All of lore.kernel.org
 help / color / mirror / Atom feed
From: Andrew Lunn <andrew@lunn.ch>
To: John David Anglin <dave.anglin@bell.net>
Cc: Russell King <linux@arm.linux.org.uk>,
	Vivien Didelot <vivien.didelot@savoirfairelinux.com>,
	Florian Fainelli <f.fainelli@gmail.com>,
	netdev@vger.kernel.org
Subject: Re: [PATCH net] dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit
Date: Thu, 14 Feb 2019 03:07:23 +0100	[thread overview]
Message-ID: <20190214020723.GE24589@lunn.ch> (raw)
In-Reply-To: <6a1ebc61-3505-beb8-21cb-ea42ad9fe67e@bell.net>

On Mon, Feb 11, 2019 at 01:40:21PM -0500, John David Anglin wrote:
> The GPIO interrupt controller on the espressobin board only supports edge interrupts.
> If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
> possible to miss an edge.  When this happens, the INTn pin on the Marvell switch is
> stuck low and no further interrupts occur.
> 
> I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
> a race in handling device interrupts (e.g. PHY link interrupts).  Some interrupts are
> directly cleared by reading the Global 1 status register.  However, the device interrupt
> flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
> This is done by reading the relevant SERDES and PHY status register.
> 
> The code only services interrupts whose status bit is set at the time of reading its status
> register.  If an interrupt event occurs after its status is read and before all interrupts
> are serviced, then this event will not be serviced and the INTn output pin will remain low.
> 
> This is not a problem with polling or level interrupts since the handler will be called
> again to process the event.  However, it's a big problem when using level interrupts.
> 
> The fix presented here is to add a loop around the code servicing switch interrupts.  If
> any pending interrupts remain after the current set has been handled, we loop and process
> the new set.  If there are no pending interrupts after servicing, we are sure that INTn has
> gone high and we will get an edge when a new event occurs.
> 
> Tested on espressobin board.
> 
> Signed-off-by:  John David Anglin <dave.anglin@bell.net>

Fixes: dc30c35be720 ("net: dsa: mv88e6xxx: Implement interrupt support.")

Tested-by: Andrew Lunn <andrew@lunn.ch>

David, please ensure that Heiner's patch:

net: phy: fix interrupt handling in non-started states

is applied first. Otherwise we can get into an interrupt storm.

    Andrew

  parent reply	other threads:[~2019-02-14  2:07 UTC|newest]

Thread overview: 52+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-01-22 19:16 net: phylink: dsa: mv88e6xxx: flaky link detection on switch ports with internal PHYs John David Anglin
2019-01-22 20:28 ` Andrew Lunn
2019-01-22 21:40   ` John David Anglin
2019-01-22 22:36     ` Andrew Lunn
2019-01-22 23:52       ` John David Anglin
2019-01-23  0:11       ` John David Anglin
2019-01-23  0:22         ` Andrew Lunn
2019-01-25 16:30           ` John David Anglin
2019-01-25 16:48             ` Russell King - ARM Linux admin
2019-01-25 18:38               ` John David Anglin
2019-01-30 17:08           ` John David Anglin
2019-01-30 17:28             ` Andrew Lunn
2019-01-30 19:01               ` John David Anglin
2019-01-30 19:09                 ` Andrew Lunn
2019-01-30 22:24               ` John David Anglin
2019-01-30 22:38                 ` Andrew Lunn
2019-01-31  1:27                   ` John David Anglin
2019-01-31 17:27                     ` John David Anglin
2019-02-04 18:37                       ` [PATCH] net: phylink: dsa: mv88e6xxx: Revise irq setup ordering John David Anglin
2019-02-04 19:35                         ` Andrew Lunn
2019-02-04 19:52                           ` John David Anglin
2019-02-04 20:19                             ` Andrew Lunn
2019-02-04 21:38                               ` John David Anglin
2019-02-04 22:47                                 ` Andrew Lunn
2019-02-04 21:59                         ` [PATCH v2] net: " John David Anglin
2019-02-04 23:14                           ` Andrew Lunn
2019-02-05  0:38                             ` John David Anglin
2019-02-05  2:21                               ` Andrew Lunn
2019-02-05 19:20                                 ` John David Anglin
2019-02-05 19:54                                   ` Andrew Lunn
2019-02-05 18:37                           ` David Miller
2019-02-11 18:40                           ` [PATCH net] dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit John David Anglin
2019-02-11 23:33                             ` Andrew Lunn
2019-02-12  0:57                               ` John David Anglin
2019-02-12  1:21                                 ` Andrew Lunn
2019-02-12  3:58                                 ` Andrew Lunn
2019-02-12  6:51                                   ` Heiner Kallweit
2019-02-12 12:56                                     ` Andrew Lunn
2019-02-12 18:42                                       ` Heiner Kallweit
2019-02-12 20:09                                       ` John David Anglin
2019-02-12 16:30                                     ` Russell King - ARM Linux admin
2019-02-12 20:11                                       ` Heiner Kallweit
2019-02-12 20:54                                       ` Heiner Kallweit
2019-02-12 22:55                                         ` Russell King - ARM Linux admin
2019-02-14  2:07                             ` Andrew Lunn [this message]
2019-02-14  4:47                               ` David Miller
2019-02-14  4:50                                 ` Andrew Lunn
2019-02-14 15:27                                   ` David Miller
2019-01-22 23:12 ` net: phylink: dsa: mv88e6xxx: flaky link detection on switch ports with internal PHYs Andrew Lunn
2019-01-22 23:48   ` John David Anglin
2019-01-23  0:00   ` John David Anglin
2019-01-23  0:04     ` Florian Fainelli

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190214020723.GE24589@lunn.ch \
    --to=andrew@lunn.ch \
    --cc=dave.anglin@bell.net \
    --cc=f.fainelli@gmail.com \
    --cc=linux@arm.linux.org.uk \
    --cc=netdev@vger.kernel.org \
    --cc=vivien.didelot@savoirfairelinux.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.