* [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller
@ 2019-02-12 16:28 ` Neil Armstrong
0 siblings, 0 replies; 19+ messages in thread
From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw)
To: jbrunet
Cc: linux-amlogic, linux-kernel, linux-clk, linux-arm-kernel,
Neil Armstrong
This patchset add support for the Amlogic G12A SoC family Always-On
clock and reset controller.
This adds support for clocks on the Always-On domain like :
- Always-On UARTS & I2C Controllers
- CEC Controllers
- SARADC source and bus clock
- Infrared Decoder/Encoder bus clock
- USB 32K reference clock
This also adds resets lines for :
- Always-On UARTS & I2C Controllers
- SARADC, Infrared Decoder/Encoder
This patchset depends on the ("clk: meson: rework drivers dependencies")
from Jerome Brunet at [1].
Changes from v1 at [2]:
- Moved unused bindings ID out of the dt-bindings header
- Added comment about CLK_IGNORE_UNUSED
[1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com
[2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com
Neil Armstrong (2):
dt-bindings: clk: add G12A AO Clock and Reset Bindings
clk: meson: Add G12A AO Clock + Reset Controller
.../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 +
drivers/clk/meson/Kconfig | 2 +
drivers/clk/meson/Makefile | 2 +-
drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++
drivers/clk/meson/g12a-aoclk.h | 34 ++
include/dt-bindings/clock/g12a-aoclkc.h | 34 ++
include/dt-bindings/reset/g12a-aoclkc.h | 18 +
7 files changed, 544 insertions(+), 1 deletion(-)
create mode 100644 drivers/clk/meson/g12a-aoclk.c
create mode 100644 drivers/clk/meson/g12a-aoclk.h
create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h
create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h
--
2.20.1
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller @ 2019-02-12 16:28 ` Neil Armstrong 0 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw) To: jbrunet Cc: linux-amlogic, linux-kernel, linux-clk, linux-arm-kernel, Neil Armstrong This patchset add support for the Amlogic G12A SoC family Always-On clock and reset controller. This adds support for clocks on the Always-On domain like : - Always-On UARTS & I2C Controllers - CEC Controllers - SARADC source and bus clock - Infrared Decoder/Encoder bus clock - USB 32K reference clock This also adds resets lines for : - Always-On UARTS & I2C Controllers - SARADC, Infrared Decoder/Encoder This patchset depends on the ("clk: meson: rework drivers dependencies") from Jerome Brunet at [1]. Changes from v1 at [2]: - Moved unused bindings ID out of the dt-bindings header - Added comment about CLK_IGNORE_UNUSED [1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com [2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com Neil Armstrong (2): dt-bindings: clk: add G12A AO Clock and Reset Bindings clk: meson: Add G12A AO Clock + Reset Controller .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + drivers/clk/meson/Kconfig | 2 + drivers/clk/meson/Makefile | 2 +- drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++ drivers/clk/meson/g12a-aoclk.h | 34 ++ include/dt-bindings/clock/g12a-aoclkc.h | 34 ++ include/dt-bindings/reset/g12a-aoclkc.h | 18 + 7 files changed, 544 insertions(+), 1 deletion(-) create mode 100644 drivers/clk/meson/g12a-aoclk.c create mode 100644 drivers/clk/meson/g12a-aoclk.h create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller @ 2019-02-12 16:28 ` Neil Armstrong 0 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw) To: jbrunet Cc: Neil Armstrong, linux-clk, linux-amlogic, linux-arm-kernel, linux-kernel This patchset add support for the Amlogic G12A SoC family Always-On clock and reset controller. This adds support for clocks on the Always-On domain like : - Always-On UARTS & I2C Controllers - CEC Controllers - SARADC source and bus clock - Infrared Decoder/Encoder bus clock - USB 32K reference clock This also adds resets lines for : - Always-On UARTS & I2C Controllers - SARADC, Infrared Decoder/Encoder This patchset depends on the ("clk: meson: rework drivers dependencies") from Jerome Brunet at [1]. Changes from v1 at [2]: - Moved unused bindings ID out of the dt-bindings header - Added comment about CLK_IGNORE_UNUSED [1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com [2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com Neil Armstrong (2): dt-bindings: clk: add G12A AO Clock and Reset Bindings clk: meson: Add G12A AO Clock + Reset Controller .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + drivers/clk/meson/Kconfig | 2 + drivers/clk/meson/Makefile | 2 +- drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++ drivers/clk/meson/g12a-aoclk.h | 34 ++ include/dt-bindings/clock/g12a-aoclkc.h | 34 ++ include/dt-bindings/reset/g12a-aoclkc.h | 18 + 7 files changed, 544 insertions(+), 1 deletion(-) create mode 100644 drivers/clk/meson/g12a-aoclk.c create mode 100644 drivers/clk/meson/g12a-aoclk.h create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h -- 2.20.1 ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 1/2] dt-bindings: clk: add G12A AO Clock and Reset Bindings 2019-02-12 16:28 ` Neil Armstrong (?) @ 2019-02-12 16:28 ` Neil Armstrong -1 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw) To: jbrunet, devicetree Cc: linux-amlogic, linux-kernel, linux-clk, linux-arm-kernel, Neil Armstrong Add bindings for the Amlogic G12A AO Clock and Reset controllers. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + include/dt-bindings/clock/g12a-aoclkc.h | 34 +++++++++++++++++++ include/dt-bindings/reset/g12a-aoclkc.h | 18 ++++++++++ 3 files changed, 53 insertions(+) create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt index 79511d7bb321..c41f0be5d438 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -10,6 +10,7 @@ Required Properties: - GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc" - GXM (S912) : "amlogic,meson-gxm-aoclkc" - AXG (A113D, A113X) : "amlogic,meson-axg-aoclkc" + - G12A (S905X2, S905D2, S905Y2) : "amlogic,meson-g12a-aoclkc" followed by the common "amlogic,meson-gx-aoclkc" - clocks: list of clock phandle, one for each entry clock-names. - clock-names: should contain the following: diff --git a/include/dt-bindings/clock/g12a-aoclkc.h b/include/dt-bindings/clock/g12a-aoclkc.h new file mode 100644 index 000000000000..8db01ffbeb06 --- /dev/null +++ b/include/dt-bindings/clock/g12a-aoclkc.h @@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ +/* + * Copyright (c) 2016 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + * + * Copyright (c) 2018 Amlogic, inc. + * Author: Qiufang Dai <qiufang.dai@amlogic.com> + */ + +#ifndef DT_BINDINGS_CLOCK_AMLOGIC_MESON_G12A_AOCLK +#define DT_BINDINGS_CLOCK_AMLOGIC_MESON_G12A_AOCLK + +#define CLKID_AO_AHB 0 +#define CLKID_AO_IR_IN 1 +#define CLKID_AO_I2C_M0 2 +#define CLKID_AO_I2C_S0 3 +#define CLKID_AO_UART 4 +#define CLKID_AO_PROD_I2C 5 +#define CLKID_AO_UART2 6 +#define CLKID_AO_IR_OUT 7 +#define CLKID_AO_SAR_ADC 8 +#define CLKID_AO_MAILBOX 9 +#define CLKID_AO_M3 10 +#define CLKID_AO_AHB_SRAM 11 +#define CLKID_AO_RTI 12 +#define CLKID_AO_M4_FCLK 13 +#define CLKID_AO_M4_HCLK 14 +#define CLKID_AO_CLK81 15 +#define CLKID_AO_SAR_ADC_CLK 18 +#define CLKID_AO_32K 23 +#define CLKID_AO_CEC 27 +#define CLKID_AO_CTS_RTC_OSCIN 28 + +#endif diff --git a/include/dt-bindings/reset/g12a-aoclkc.h b/include/dt-bindings/reset/g12a-aoclkc.h new file mode 100644 index 000000000000..bd2e2337135c --- /dev/null +++ b/include/dt-bindings/reset/g12a-aoclkc.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ +/* + * Copyright (c) 2016 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#ifndef DT_BINDINGS_RESET_AMLOGIC_MESON_G12A_AOCLK +#define DT_BINDINGS_RESET_AMLOGIC_MESON_G12A_AOCLK + +#define RESET_AO_IR_IN 0 +#define RESET_AO_UART 1 +#define RESET_AO_I2C_M 2 +#define RESET_AO_I2C_S 3 +#define RESET_AO_SAR_ADC 4 +#define RESET_AO_UART2 5 +#define RESET_AO_IR_OUT 6 + +#endif -- 2.20.1 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 1/2] dt-bindings: clk: add G12A AO Clock and Reset Bindings @ 2019-02-12 16:28 ` Neil Armstrong 0 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw) To: jbrunet, devicetree Cc: linux-amlogic, linux-kernel, linux-clk, linux-arm-kernel, Neil Armstrong Add bindings for the Amlogic G12A AO Clock and Reset controllers. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + include/dt-bindings/clock/g12a-aoclkc.h | 34 +++++++++++++++++++ include/dt-bindings/reset/g12a-aoclkc.h | 18 ++++++++++ 3 files changed, 53 insertions(+) create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt index 79511d7bb321..c41f0be5d438 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -10,6 +10,7 @@ Required Properties: - GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc" - GXM (S912) : "amlogic,meson-gxm-aoclkc" - AXG (A113D, A113X) : "amlogic,meson-axg-aoclkc" + - G12A (S905X2, S905D2, S905Y2) : "amlogic,meson-g12a-aoclkc" followed by the common "amlogic,meson-gx-aoclkc" - clocks: list of clock phandle, one for each entry clock-names. - clock-names: should contain the following: diff --git a/include/dt-bindings/clock/g12a-aoclkc.h b/include/dt-bindings/clock/g12a-aoclkc.h new file mode 100644 index 000000000000..8db01ffbeb06 --- /dev/null +++ b/include/dt-bindings/clock/g12a-aoclkc.h @@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ +/* + * Copyright (c) 2016 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + * + * Copyright (c) 2018 Amlogic, inc. + * Author: Qiufang Dai <qiufang.dai@amlogic.com> + */ + +#ifndef DT_BINDINGS_CLOCK_AMLOGIC_MESON_G12A_AOCLK +#define DT_BINDINGS_CLOCK_AMLOGIC_MESON_G12A_AOCLK + +#define CLKID_AO_AHB 0 +#define CLKID_AO_IR_IN 1 +#define CLKID_AO_I2C_M0 2 +#define CLKID_AO_I2C_S0 3 +#define CLKID_AO_UART 4 +#define CLKID_AO_PROD_I2C 5 +#define CLKID_AO_UART2 6 +#define CLKID_AO_IR_OUT 7 +#define CLKID_AO_SAR_ADC 8 +#define CLKID_AO_MAILBOX 9 +#define CLKID_AO_M3 10 +#define CLKID_AO_AHB_SRAM 11 +#define CLKID_AO_RTI 12 +#define CLKID_AO_M4_FCLK 13 +#define CLKID_AO_M4_HCLK 14 +#define CLKID_AO_CLK81 15 +#define CLKID_AO_SAR_ADC_CLK 18 +#define CLKID_AO_32K 23 +#define CLKID_AO_CEC 27 +#define CLKID_AO_CTS_RTC_OSCIN 28 + +#endif diff --git a/include/dt-bindings/reset/g12a-aoclkc.h b/include/dt-bindings/reset/g12a-aoclkc.h new file mode 100644 index 000000000000..bd2e2337135c --- /dev/null +++ b/include/dt-bindings/reset/g12a-aoclkc.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ +/* + * Copyright (c) 2016 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#ifndef DT_BINDINGS_RESET_AMLOGIC_MESON_G12A_AOCLK +#define DT_BINDINGS_RESET_AMLOGIC_MESON_G12A_AOCLK + +#define RESET_AO_IR_IN 0 +#define RESET_AO_UART 1 +#define RESET_AO_I2C_M 2 +#define RESET_AO_I2C_S 3 +#define RESET_AO_SAR_ADC 4 +#define RESET_AO_UART2 5 +#define RESET_AO_IR_OUT 6 + +#endif -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 1/2] dt-bindings: clk: add G12A AO Clock and Reset Bindings @ 2019-02-12 16:28 ` Neil Armstrong 0 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw) To: jbrunet, devicetree Cc: Neil Armstrong, linux-clk, linux-amlogic, linux-arm-kernel, linux-kernel Add bindings for the Amlogic G12A AO Clock and Reset controllers. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + include/dt-bindings/clock/g12a-aoclkc.h | 34 +++++++++++++++++++ include/dt-bindings/reset/g12a-aoclkc.h | 18 ++++++++++ 3 files changed, 53 insertions(+) create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt index 79511d7bb321..c41f0be5d438 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -10,6 +10,7 @@ Required Properties: - GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc" - GXM (S912) : "amlogic,meson-gxm-aoclkc" - AXG (A113D, A113X) : "amlogic,meson-axg-aoclkc" + - G12A (S905X2, S905D2, S905Y2) : "amlogic,meson-g12a-aoclkc" followed by the common "amlogic,meson-gx-aoclkc" - clocks: list of clock phandle, one for each entry clock-names. - clock-names: should contain the following: diff --git a/include/dt-bindings/clock/g12a-aoclkc.h b/include/dt-bindings/clock/g12a-aoclkc.h new file mode 100644 index 000000000000..8db01ffbeb06 --- /dev/null +++ b/include/dt-bindings/clock/g12a-aoclkc.h @@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ +/* + * Copyright (c) 2016 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + * + * Copyright (c) 2018 Amlogic, inc. + * Author: Qiufang Dai <qiufang.dai@amlogic.com> + */ + +#ifndef DT_BINDINGS_CLOCK_AMLOGIC_MESON_G12A_AOCLK +#define DT_BINDINGS_CLOCK_AMLOGIC_MESON_G12A_AOCLK + +#define CLKID_AO_AHB 0 +#define CLKID_AO_IR_IN 1 +#define CLKID_AO_I2C_M0 2 +#define CLKID_AO_I2C_S0 3 +#define CLKID_AO_UART 4 +#define CLKID_AO_PROD_I2C 5 +#define CLKID_AO_UART2 6 +#define CLKID_AO_IR_OUT 7 +#define CLKID_AO_SAR_ADC 8 +#define CLKID_AO_MAILBOX 9 +#define CLKID_AO_M3 10 +#define CLKID_AO_AHB_SRAM 11 +#define CLKID_AO_RTI 12 +#define CLKID_AO_M4_FCLK 13 +#define CLKID_AO_M4_HCLK 14 +#define CLKID_AO_CLK81 15 +#define CLKID_AO_SAR_ADC_CLK 18 +#define CLKID_AO_32K 23 +#define CLKID_AO_CEC 27 +#define CLKID_AO_CTS_RTC_OSCIN 28 + +#endif diff --git a/include/dt-bindings/reset/g12a-aoclkc.h b/include/dt-bindings/reset/g12a-aoclkc.h new file mode 100644 index 000000000000..bd2e2337135c --- /dev/null +++ b/include/dt-bindings/reset/g12a-aoclkc.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ +/* + * Copyright (c) 2016 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#ifndef DT_BINDINGS_RESET_AMLOGIC_MESON_G12A_AOCLK +#define DT_BINDINGS_RESET_AMLOGIC_MESON_G12A_AOCLK + +#define RESET_AO_IR_IN 0 +#define RESET_AO_UART 1 +#define RESET_AO_I2C_M 2 +#define RESET_AO_I2C_S 3 +#define RESET_AO_SAR_ADC 4 +#define RESET_AO_UART2 5 +#define RESET_AO_IR_OUT 6 + +#endif -- 2.20.1 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: clk: add G12A AO Clock and Reset Bindings 2019-02-12 16:28 ` Neil Armstrong (?) (?) @ 2019-02-18 20:02 ` Rob Herring -1 siblings, 0 replies; 19+ messages in thread From: Rob Herring @ 2019-02-18 20:02 UTC (permalink / raw) To: Neil Armstrong Cc: devicetree, Neil Armstrong, linux-kernel, linux-amlogic, linux-clk, linux-arm-kernel, jbrunet On Tue, 12 Feb 2019 17:28:58 +0100, Neil Armstrong wrote: > Add bindings for the Amlogic G12A AO Clock and Reset controllers. > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + > include/dt-bindings/clock/g12a-aoclkc.h | 34 +++++++++++++++++++ > include/dt-bindings/reset/g12a-aoclkc.h | 18 ++++++++++ > 3 files changed, 53 insertions(+) > create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h > create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h > Reviewed-by: Rob Herring <robh@kernel.org> _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: clk: add G12A AO Clock and Reset Bindings @ 2019-02-18 20:02 ` Rob Herring 0 siblings, 0 replies; 19+ messages in thread From: Rob Herring @ 2019-02-18 20:02 UTC (permalink / raw) Cc: jbrunet, devicetree, Neil Armstrong, linux-clk, linux-amlogic, linux-arm-kernel, linux-kernel On Tue, 12 Feb 2019 17:28:58 +0100, Neil Armstrong wrote: > Add bindings for the Amlogic G12A AO Clock and Reset controllers. > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + > include/dt-bindings/clock/g12a-aoclkc.h | 34 +++++++++++++++++++ > include/dt-bindings/reset/g12a-aoclkc.h | 18 ++++++++++ > 3 files changed, 53 insertions(+) > create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h > create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h > Reviewed-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: clk: add G12A AO Clock and Reset Bindings @ 2019-02-18 20:02 ` Rob Herring 0 siblings, 0 replies; 19+ messages in thread From: Rob Herring @ 2019-02-18 20:02 UTC (permalink / raw) To: Neil Armstrong Cc: devicetree, Neil Armstrong, linux-kernel, linux-amlogic, linux-clk, linux-arm-kernel, jbrunet On Tue, 12 Feb 2019 17:28:58 +0100, Neil Armstrong wrote: > Add bindings for the Amlogic G12A AO Clock and Reset controllers. > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + > include/dt-bindings/clock/g12a-aoclkc.h | 34 +++++++++++++++++++ > include/dt-bindings/reset/g12a-aoclkc.h | 18 ++++++++++ > 3 files changed, 53 insertions(+) > create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h > create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h > Reviewed-by: Rob Herring <robh@kernel.org> _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: clk: add G12A AO Clock and Reset Bindings @ 2019-02-18 20:02 ` Rob Herring 0 siblings, 0 replies; 19+ messages in thread From: Rob Herring @ 2019-02-18 20:02 UTC (permalink / raw) To: Neil Armstrong Cc: jbrunet, devicetree, Neil Armstrong, linux-clk, linux-amlogic, linux-arm-kernel, linux-kernel On Tue, 12 Feb 2019 17:28:58 +0100, Neil Armstrong wrote: > Add bindings for the Amlogic G12A AO Clock and Reset controllers. > > Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> > --- > .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + > include/dt-bindings/clock/g12a-aoclkc.h | 34 +++++++++++++++++++ > include/dt-bindings/reset/g12a-aoclkc.h | 18 ++++++++++ > 3 files changed, 53 insertions(+) > create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h > create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h > Reviewed-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 2/2] clk: meson: Add G12A AO Clock + Reset Controller 2019-02-12 16:28 ` Neil Armstrong (?) @ 2019-02-12 16:28 ` Neil Armstrong -1 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw) To: jbrunet Cc: linux-amlogic, linux-kernel, linux-clk, linux-arm-kernel, Neil Armstrong Add the Amlogic G12A AO Clock and Reset controller driver handling generation of Always-On clocks : - AO Clocks and Reset for Always-On modules - 32K Generation for USB and CEC - SAR ADC controller clock Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- drivers/clk/meson/Kconfig | 2 + drivers/clk/meson/Makefile | 2 +- drivers/clk/meson/g12a-aoclk.c | 454 +++++++++++++++++++++++++++++++++ drivers/clk/meson/g12a-aoclk.h | 34 +++ 4 files changed, 491 insertions(+), 1 deletion(-) create mode 100644 drivers/clk/meson/g12a-aoclk.c create mode 100644 drivers/clk/meson/g12a-aoclk.h diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig index b72439315340..3858747f5438 100644 --- a/drivers/clk/meson/Kconfig +++ b/drivers/clk/meson/Kconfig @@ -98,8 +98,10 @@ config COMMON_CLK_G12A bool depends on ARCH_MESON select COMMON_CLK_MESON_REGMAP + select COMMON_CLK_MESON_DUALDIV select COMMON_CLK_MESON_MPLL select COMMON_CLK_MESON_PLL + select COMMON_CLK_MESON_AO_CLKC select COMMON_CLK_MESON_EE_CLKC select MFD_SYSCON help diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile index 32d17f18541e..021fc290e749 100644 --- a/drivers/clk/meson/Makefile +++ b/drivers/clk/meson/Makefile @@ -16,5 +16,5 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o -obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o +obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o diff --git a/drivers/clk/meson/g12a-aoclk.c b/drivers/clk/meson/g12a-aoclk.c new file mode 100644 index 000000000000..1994e735396b --- /dev/null +++ b/drivers/clk/meson/g12a-aoclk.c @@ -0,0 +1,454 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Amlogic Meson-AXG Clock Controller Driver + * + * Copyright (c) 2016 Baylibre SAS. + * Author: Michael Turquette <mturquette@baylibre.com> + * + * Copyright (c) 2019 Baylibre SAS. + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ +#include <linux/clk-provider.h> +#include <linux/platform_device.h> +#include <linux/reset-controller.h> +#include <linux/mfd/syscon.h> +#include "meson-aoclk.h" +#include "g12a-aoclk.h" + +#include "clk-regmap.h" +#include "clk-dualdiv.h" + +#define IN_PREFIX "ao-in-" + +/* + * AO Configuration Clock registers offsets + * Register offsets from the data sheet must be multiplied by 4. + */ +#define AO_RTI_STATUS_REG3 0x0C +#define AO_RTI_PWR_CNTL_REG0 0x10 +#define AO_RTI_GEN_CNTL_REG0 0x40 +#define AO_CLK_GATE0 0x4c +#define AO_CLK_GATE0_SP 0x50 +#define AO_OSCIN_CNTL 0x58 +#define AO_CEC_CLK_CNTL_REG0 0x74 +#define AO_CEC_CLK_CNTL_REG1 0x78 +#define AO_SAR_CLK 0x90 +#define AO_RTC_ALT_CLK_CNTL0 0x94 +#define AO_RTC_ALT_CLK_CNTL1 0x98 + +/* + * Like every other peripheral clock gate in Amlogic Clock drivers, + * we are using CLK_IGNORE_UNUSED here, so we keep the state of the + * bootloader. The goal is to remove this flag at some point. + * Actually removing it will require some extensive test to be done safely. + */ +#define AXG_AO_GATE(_name, _reg, _bit) \ +static struct clk_regmap g12a_aoclk_##_name = { \ + .data = &(struct clk_regmap_gate_data) { \ + .offset = (_reg), \ + .bit_idx = (_bit), \ + }, \ + .hw.init = &(struct clk_init_data) { \ + .name = "g12a_ao_" #_name, \ + .ops = &clk_regmap_gate_ops, \ + .parent_names = (const char *[]){ IN_PREFIX "mpeg-clk" }, \ + .num_parents = 1, \ + .flags = CLK_IGNORE_UNUSED, \ + }, \ +} + +AXG_AO_GATE(ahb, AO_CLK_GATE0, 0); +AXG_AO_GATE(ir_in, AO_CLK_GATE0, 1); +AXG_AO_GATE(i2c_m0, AO_CLK_GATE0, 2); +AXG_AO_GATE(i2c_s0, AO_CLK_GATE0, 3); +AXG_AO_GATE(uart, AO_CLK_GATE0, 4); +AXG_AO_GATE(prod_i2c, AO_CLK_GATE0, 5); +AXG_AO_GATE(uart2, AO_CLK_GATE0, 6); +AXG_AO_GATE(ir_out, AO_CLK_GATE0, 7); +AXG_AO_GATE(saradc, AO_CLK_GATE0, 8); +AXG_AO_GATE(mailbox, AO_CLK_GATE0_SP, 0); +AXG_AO_GATE(m3, AO_CLK_GATE0_SP, 1); +AXG_AO_GATE(ahb_sram, AO_CLK_GATE0_SP, 2); +AXG_AO_GATE(rti, AO_CLK_GATE0_SP, 3); +AXG_AO_GATE(m4_fclk, AO_CLK_GATE0_SP, 4); +AXG_AO_GATE(m4_hclk, AO_CLK_GATE0_SP, 5); + +static struct clk_regmap g12a_aoclk_cts_oscin = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTI_PWR_CNTL_REG0, + .bit_idx = 14, + }, + .hw.init = &(struct clk_init_data){ + .name = "cts_oscin", + .ops = &clk_regmap_gate_ro_ops, + .parent_names = (const char *[]){ IN_PREFIX "xtal" }, + .num_parents = 1, + }, +}; + +static const struct meson_clk_dualdiv_param g12a_32k_div_table[] = { + { + .dual = 1, + .n1 = 733, + .m1 = 8, + .n2 = 732, + .m2 = 11, + }, {} +}; + +/* 32k_by_oscin clock */ + +static struct clk_regmap g12a_aoclk_32k_by_oscin_pre = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTC_ALT_CLK_CNTL0, + .bit_idx = 31, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_pre", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "cts_oscin" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin_div = { + .data = &(struct meson_clk_dualdiv_data){ + .n1 = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 0, + .width = 12, + }, + .n2 = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 12, + .width = 12, + }, + .m1 = { + .reg_off = AO_RTC_ALT_CLK_CNTL1, + .shift = 0, + .width = 12, + }, + .m2 = { + .reg_off = AO_RTC_ALT_CLK_CNTL1, + .shift = 12, + .width = 12, + }, + .dual = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 28, + .width = 1, + }, + .table = g12a_32k_div_table, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_div", + .ops = &meson_clk_dualdiv_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_pre" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin_sel = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTC_ALT_CLK_CNTL1, + .mask = 0x1, + .shift = 24, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_sel", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_div", + "g12a_ao_32k_by_oscin_pre" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTC_ALT_CLK_CNTL0, + .bit_idx = 30, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_sel" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +/* cec clock */ + +static struct clk_regmap g12a_aoclk_cec_pre = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_CEC_CLK_CNTL_REG0, + .bit_idx = 31, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_pre", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "cts_oscin" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_cec_div = { + .data = &(struct meson_clk_dualdiv_data){ + .n1 = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 0, + .width = 12, + }, + .n2 = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 12, + .width = 12, + }, + .m1 = { + .reg_off = AO_CEC_CLK_CNTL_REG1, + .shift = 0, + .width = 12, + }, + .m2 = { + .reg_off = AO_CEC_CLK_CNTL_REG1, + .shift = 12, + .width = 12, + }, + .dual = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 28, + .width = 1, + }, + .table = g12a_32k_div_table, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_div", + .ops = &meson_clk_dualdiv_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_pre" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_cec_sel = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_CEC_CLK_CNTL_REG1, + .mask = 0x1, + .shift = 24, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_sel", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_div", + "g12a_ao_cec_pre" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_cec = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_CEC_CLK_CNTL_REG0, + .bit_idx = 30, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_sel" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_cts_rtc_oscin = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTI_PWR_CNTL_REG0, + .mask = 0x1, + .shift = 10, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cts_rtc_oscin", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin", + IN_PREFIX "ext_32k-0" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_clk81 = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTI_PWR_CNTL_REG0, + .mask = 0x1, + .shift = 8, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_clk81", + .ops = &clk_regmap_mux_ro_ops, + .parent_names = (const char *[]){ IN_PREFIX "mpeg-clk", + "g12a_ao_cts_rtc_oscin"}, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_mux = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_SAR_CLK, + .mask = 0x3, + .shift = 9, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_mux", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ IN_PREFIX "xtal", + "g12a_ao_clk81" }, + .num_parents = 2, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_div = { + .data = &(struct clk_regmap_div_data) { + .offset = AO_SAR_CLK, + .shift = 0, + .width = 8, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_div", + .ops = &clk_regmap_divider_ops, + .parent_names = (const char *[]){ "g12a_ao_saradc_mux" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_gate = { + .data = &(struct clk_regmap_gate_data) { + .offset = AO_SAR_CLK, + .bit_idx = 8, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_gate", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_saradc_div" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static const unsigned int g12a_aoclk_reset[] = { + [RESET_AO_IR_IN] = 16, + [RESET_AO_UART] = 17, + [RESET_AO_I2C_M] = 18, + [RESET_AO_I2C_S] = 19, + [RESET_AO_SAR_ADC] = 20, + [RESET_AO_UART2] = 22, + [RESET_AO_IR_OUT] = 23, +}; + +static struct clk_regmap *g12a_aoclk_regmap[] = { + &g12a_aoclk_ahb, + &g12a_aoclk_ir_in, + &g12a_aoclk_i2c_m0, + &g12a_aoclk_i2c_s0, + &g12a_aoclk_uart, + &g12a_aoclk_prod_i2c, + &g12a_aoclk_uart2, + &g12a_aoclk_ir_out, + &g12a_aoclk_saradc, + &g12a_aoclk_mailbox, + &g12a_aoclk_m3, + &g12a_aoclk_ahb_sram, + &g12a_aoclk_rti, + &g12a_aoclk_m4_fclk, + &g12a_aoclk_m4_hclk, + &g12a_aoclk_cts_oscin, + &g12a_aoclk_32k_by_oscin_pre, + &g12a_aoclk_32k_by_oscin_div, + &g12a_aoclk_32k_by_oscin_sel, + &g12a_aoclk_32k_by_oscin, + &g12a_aoclk_cec_pre, + &g12a_aoclk_cec_div, + &g12a_aoclk_cec_sel, + &g12a_aoclk_cec, + &g12a_aoclk_cts_rtc_oscin, + &g12a_aoclk_clk81, + &g12a_aoclk_saradc_mux, + &g12a_aoclk_saradc_div, + &g12a_aoclk_saradc_gate, +}; + +static const struct clk_hw_onecell_data g12a_aoclk_onecell_data = { + .hws = { + [CLKID_AO_AHB] = &g12a_aoclk_ahb.hw, + [CLKID_AO_IR_IN] = &g12a_aoclk_ir_in.hw, + [CLKID_AO_I2C_M0] = &g12a_aoclk_i2c_m0.hw, + [CLKID_AO_I2C_S0] = &g12a_aoclk_i2c_s0.hw, + [CLKID_AO_UART] = &g12a_aoclk_uart.hw, + [CLKID_AO_PROD_I2C] = &g12a_aoclk_prod_i2c.hw, + [CLKID_AO_UART2] = &g12a_aoclk_uart2.hw, + [CLKID_AO_IR_OUT] = &g12a_aoclk_ir_out.hw, + [CLKID_AO_SAR_ADC] = &g12a_aoclk_saradc.hw, + [CLKID_AO_MAILBOX] = &g12a_aoclk_mailbox.hw, + [CLKID_AO_M3] = &g12a_aoclk_m3.hw, + [CLKID_AO_AHB_SRAM] = &g12a_aoclk_ahb_sram.hw, + [CLKID_AO_RTI] = &g12a_aoclk_rti.hw, + [CLKID_AO_M4_FCLK] = &g12a_aoclk_m4_fclk.hw, + [CLKID_AO_M4_HCLK] = &g12a_aoclk_m4_hclk.hw, + [CLKID_AO_CLK81] = &g12a_aoclk_clk81.hw, + [CLKID_AO_SAR_ADC_SEL] = &g12a_aoclk_saradc_mux.hw, + [CLKID_AO_SAR_ADC_DIV] = &g12a_aoclk_saradc_div.hw, + [CLKID_AO_SAR_ADC_CLK] = &g12a_aoclk_saradc_gate.hw, + [CLKID_AO_CTS_OSCIN] = &g12a_aoclk_cts_oscin.hw, + [CLKID_AO_32K_PRE] = &g12a_aoclk_32k_by_oscin_pre.hw, + [CLKID_AO_32K_DIV] = &g12a_aoclk_32k_by_oscin_div.hw, + [CLKID_AO_32K_SEL] = &g12a_aoclk_32k_by_oscin_sel.hw, + [CLKID_AO_32K] = &g12a_aoclk_32k_by_oscin.hw, + [CLKID_AO_CEC_PRE] = &g12a_aoclk_cec_pre.hw, + [CLKID_AO_CEC_DIV] = &g12a_aoclk_cec_div.hw, + [CLKID_AO_CEC_SEL] = &g12a_aoclk_cec_sel.hw, + [CLKID_AO_CEC] = &g12a_aoclk_cec.hw, + [CLKID_AO_CTS_RTC_OSCIN] = &g12a_aoclk_cts_rtc_oscin.hw, + }, + .num = NR_CLKS, +}; + +static const struct meson_aoclk_input g12a_aoclk_inputs[] = { + { .name = "xtal", .required = true }, + { .name = "mpeg-clk", .required = true }, + { .name = "ext-32k-0", .required = false }, +}; + +static const struct meson_aoclk_data g12a_aoclkc_data = { + .reset_reg = AO_RTI_GEN_CNTL_REG0, + .num_reset = ARRAY_SIZE(g12a_aoclk_reset), + .reset = g12a_aoclk_reset, + .num_clks = ARRAY_SIZE(g12a_aoclk_regmap), + .clks = g12a_aoclk_regmap, + .hw_data = &g12a_aoclk_onecell_data, + .inputs = g12a_aoclk_inputs, + .num_inputs = ARRAY_SIZE(g12a_aoclk_inputs), + .input_prefix = IN_PREFIX, +}; + +static const struct of_device_id g12a_aoclkc_match_table[] = { + { + .compatible = "amlogic,meson-g12a-aoclkc", + .data = &g12a_aoclkc_data, + }, + { } +}; + +static struct platform_driver g12a_aoclkc_driver = { + .probe = meson_aoclkc_probe, + .driver = { + .name = "g12a-aoclkc", + .of_match_table = g12a_aoclkc_match_table, + }, +}; + +builtin_platform_driver(g12a_aoclkc_driver); diff --git a/drivers/clk/meson/g12a-aoclk.h b/drivers/clk/meson/g12a-aoclk.h new file mode 100644 index 000000000000..04b0d5506641 --- /dev/null +++ b/drivers/clk/meson/g12a-aoclk.h @@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#ifndef __G12A_AOCLKC_H +#define __G12A_AOCLKC_H + +/* + * CLKID index values + * + * These indices are entirely contrived and do not map onto the hardware. + * It has now been decided to expose everything by default in the DT header: + * include/dt-bindings/clock/g12a-aoclkc.h. Only the clocks ids we don't want + * to expose, such as the internal muxes and dividers of composite clocks, + * will remain defined here. + */ +#define CLKID_AO_SAR_ADC_SEL 16 +#define CLKID_AO_SAR_ADC_DIV 17 +#define CLKID_AO_CTS_OSCIN 19 +#define CLKID_AO_32K_PRE 20 +#define CLKID_AO_32K_DIV 21 +#define CLKID_AO_32K_SEL 22 +#define CLKID_AO_CEC_PRE 24 +#define CLKID_AO_CEC_DIV 25 +#define CLKID_AO_CEC_SEL 26 + +#define NR_CLKS 29 + +#include <dt-bindings/clock/g12a-aoclkc.h> +#include <dt-bindings/reset/g12a-aoclkc.h> + +#endif /* __G12A_AOCLKC_H */ -- 2.20.1 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 2/2] clk: meson: Add G12A AO Clock + Reset Controller @ 2019-02-12 16:28 ` Neil Armstrong 0 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw) To: jbrunet Cc: linux-amlogic, linux-kernel, linux-clk, linux-arm-kernel, Neil Armstrong Add the Amlogic G12A AO Clock and Reset controller driver handling generation of Always-On clocks : - AO Clocks and Reset for Always-On modules - 32K Generation for USB and CEC - SAR ADC controller clock Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- drivers/clk/meson/Kconfig | 2 + drivers/clk/meson/Makefile | 2 +- drivers/clk/meson/g12a-aoclk.c | 454 +++++++++++++++++++++++++++++++++ drivers/clk/meson/g12a-aoclk.h | 34 +++ 4 files changed, 491 insertions(+), 1 deletion(-) create mode 100644 drivers/clk/meson/g12a-aoclk.c create mode 100644 drivers/clk/meson/g12a-aoclk.h diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig index b72439315340..3858747f5438 100644 --- a/drivers/clk/meson/Kconfig +++ b/drivers/clk/meson/Kconfig @@ -98,8 +98,10 @@ config COMMON_CLK_G12A bool depends on ARCH_MESON select COMMON_CLK_MESON_REGMAP + select COMMON_CLK_MESON_DUALDIV select COMMON_CLK_MESON_MPLL select COMMON_CLK_MESON_PLL + select COMMON_CLK_MESON_AO_CLKC select COMMON_CLK_MESON_EE_CLKC select MFD_SYSCON help diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile index 32d17f18541e..021fc290e749 100644 --- a/drivers/clk/meson/Makefile +++ b/drivers/clk/meson/Makefile @@ -16,5 +16,5 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o -obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o +obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o diff --git a/drivers/clk/meson/g12a-aoclk.c b/drivers/clk/meson/g12a-aoclk.c new file mode 100644 index 000000000000..1994e735396b --- /dev/null +++ b/drivers/clk/meson/g12a-aoclk.c @@ -0,0 +1,454 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Amlogic Meson-AXG Clock Controller Driver + * + * Copyright (c) 2016 Baylibre SAS. + * Author: Michael Turquette <mturquette@baylibre.com> + * + * Copyright (c) 2019 Baylibre SAS. + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ +#include <linux/clk-provider.h> +#include <linux/platform_device.h> +#include <linux/reset-controller.h> +#include <linux/mfd/syscon.h> +#include "meson-aoclk.h" +#include "g12a-aoclk.h" + +#include "clk-regmap.h" +#include "clk-dualdiv.h" + +#define IN_PREFIX "ao-in-" + +/* + * AO Configuration Clock registers offsets + * Register offsets from the data sheet must be multiplied by 4. + */ +#define AO_RTI_STATUS_REG3 0x0C +#define AO_RTI_PWR_CNTL_REG0 0x10 +#define AO_RTI_GEN_CNTL_REG0 0x40 +#define AO_CLK_GATE0 0x4c +#define AO_CLK_GATE0_SP 0x50 +#define AO_OSCIN_CNTL 0x58 +#define AO_CEC_CLK_CNTL_REG0 0x74 +#define AO_CEC_CLK_CNTL_REG1 0x78 +#define AO_SAR_CLK 0x90 +#define AO_RTC_ALT_CLK_CNTL0 0x94 +#define AO_RTC_ALT_CLK_CNTL1 0x98 + +/* + * Like every other peripheral clock gate in Amlogic Clock drivers, + * we are using CLK_IGNORE_UNUSED here, so we keep the state of the + * bootloader. The goal is to remove this flag at some point. + * Actually removing it will require some extensive test to be done safely. + */ +#define AXG_AO_GATE(_name, _reg, _bit) \ +static struct clk_regmap g12a_aoclk_##_name = { \ + .data = &(struct clk_regmap_gate_data) { \ + .offset = (_reg), \ + .bit_idx = (_bit), \ + }, \ + .hw.init = &(struct clk_init_data) { \ + .name = "g12a_ao_" #_name, \ + .ops = &clk_regmap_gate_ops, \ + .parent_names = (const char *[]){ IN_PREFIX "mpeg-clk" }, \ + .num_parents = 1, \ + .flags = CLK_IGNORE_UNUSED, \ + }, \ +} + +AXG_AO_GATE(ahb, AO_CLK_GATE0, 0); +AXG_AO_GATE(ir_in, AO_CLK_GATE0, 1); +AXG_AO_GATE(i2c_m0, AO_CLK_GATE0, 2); +AXG_AO_GATE(i2c_s0, AO_CLK_GATE0, 3); +AXG_AO_GATE(uart, AO_CLK_GATE0, 4); +AXG_AO_GATE(prod_i2c, AO_CLK_GATE0, 5); +AXG_AO_GATE(uart2, AO_CLK_GATE0, 6); +AXG_AO_GATE(ir_out, AO_CLK_GATE0, 7); +AXG_AO_GATE(saradc, AO_CLK_GATE0, 8); +AXG_AO_GATE(mailbox, AO_CLK_GATE0_SP, 0); +AXG_AO_GATE(m3, AO_CLK_GATE0_SP, 1); +AXG_AO_GATE(ahb_sram, AO_CLK_GATE0_SP, 2); +AXG_AO_GATE(rti, AO_CLK_GATE0_SP, 3); +AXG_AO_GATE(m4_fclk, AO_CLK_GATE0_SP, 4); +AXG_AO_GATE(m4_hclk, AO_CLK_GATE0_SP, 5); + +static struct clk_regmap g12a_aoclk_cts_oscin = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTI_PWR_CNTL_REG0, + .bit_idx = 14, + }, + .hw.init = &(struct clk_init_data){ + .name = "cts_oscin", + .ops = &clk_regmap_gate_ro_ops, + .parent_names = (const char *[]){ IN_PREFIX "xtal" }, + .num_parents = 1, + }, +}; + +static const struct meson_clk_dualdiv_param g12a_32k_div_table[] = { + { + .dual = 1, + .n1 = 733, + .m1 = 8, + .n2 = 732, + .m2 = 11, + }, {} +}; + +/* 32k_by_oscin clock */ + +static struct clk_regmap g12a_aoclk_32k_by_oscin_pre = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTC_ALT_CLK_CNTL0, + .bit_idx = 31, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_pre", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "cts_oscin" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin_div = { + .data = &(struct meson_clk_dualdiv_data){ + .n1 = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 0, + .width = 12, + }, + .n2 = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 12, + .width = 12, + }, + .m1 = { + .reg_off = AO_RTC_ALT_CLK_CNTL1, + .shift = 0, + .width = 12, + }, + .m2 = { + .reg_off = AO_RTC_ALT_CLK_CNTL1, + .shift = 12, + .width = 12, + }, + .dual = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 28, + .width = 1, + }, + .table = g12a_32k_div_table, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_div", + .ops = &meson_clk_dualdiv_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_pre" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin_sel = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTC_ALT_CLK_CNTL1, + .mask = 0x1, + .shift = 24, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_sel", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_div", + "g12a_ao_32k_by_oscin_pre" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTC_ALT_CLK_CNTL0, + .bit_idx = 30, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_sel" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +/* cec clock */ + +static struct clk_regmap g12a_aoclk_cec_pre = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_CEC_CLK_CNTL_REG0, + .bit_idx = 31, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_pre", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "cts_oscin" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_cec_div = { + .data = &(struct meson_clk_dualdiv_data){ + .n1 = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 0, + .width = 12, + }, + .n2 = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 12, + .width = 12, + }, + .m1 = { + .reg_off = AO_CEC_CLK_CNTL_REG1, + .shift = 0, + .width = 12, + }, + .m2 = { + .reg_off = AO_CEC_CLK_CNTL_REG1, + .shift = 12, + .width = 12, + }, + .dual = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 28, + .width = 1, + }, + .table = g12a_32k_div_table, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_div", + .ops = &meson_clk_dualdiv_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_pre" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_cec_sel = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_CEC_CLK_CNTL_REG1, + .mask = 0x1, + .shift = 24, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_sel", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_div", + "g12a_ao_cec_pre" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_cec = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_CEC_CLK_CNTL_REG0, + .bit_idx = 30, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_sel" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_cts_rtc_oscin = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTI_PWR_CNTL_REG0, + .mask = 0x1, + .shift = 10, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cts_rtc_oscin", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin", + IN_PREFIX "ext_32k-0" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_clk81 = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTI_PWR_CNTL_REG0, + .mask = 0x1, + .shift = 8, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_clk81", + .ops = &clk_regmap_mux_ro_ops, + .parent_names = (const char *[]){ IN_PREFIX "mpeg-clk", + "g12a_ao_cts_rtc_oscin"}, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_mux = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_SAR_CLK, + .mask = 0x3, + .shift = 9, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_mux", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ IN_PREFIX "xtal", + "g12a_ao_clk81" }, + .num_parents = 2, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_div = { + .data = &(struct clk_regmap_div_data) { + .offset = AO_SAR_CLK, + .shift = 0, + .width = 8, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_div", + .ops = &clk_regmap_divider_ops, + .parent_names = (const char *[]){ "g12a_ao_saradc_mux" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_gate = { + .data = &(struct clk_regmap_gate_data) { + .offset = AO_SAR_CLK, + .bit_idx = 8, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_gate", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_saradc_div" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static const unsigned int g12a_aoclk_reset[] = { + [RESET_AO_IR_IN] = 16, + [RESET_AO_UART] = 17, + [RESET_AO_I2C_M] = 18, + [RESET_AO_I2C_S] = 19, + [RESET_AO_SAR_ADC] = 20, + [RESET_AO_UART2] = 22, + [RESET_AO_IR_OUT] = 23, +}; + +static struct clk_regmap *g12a_aoclk_regmap[] = { + &g12a_aoclk_ahb, + &g12a_aoclk_ir_in, + &g12a_aoclk_i2c_m0, + &g12a_aoclk_i2c_s0, + &g12a_aoclk_uart, + &g12a_aoclk_prod_i2c, + &g12a_aoclk_uart2, + &g12a_aoclk_ir_out, + &g12a_aoclk_saradc, + &g12a_aoclk_mailbox, + &g12a_aoclk_m3, + &g12a_aoclk_ahb_sram, + &g12a_aoclk_rti, + &g12a_aoclk_m4_fclk, + &g12a_aoclk_m4_hclk, + &g12a_aoclk_cts_oscin, + &g12a_aoclk_32k_by_oscin_pre, + &g12a_aoclk_32k_by_oscin_div, + &g12a_aoclk_32k_by_oscin_sel, + &g12a_aoclk_32k_by_oscin, + &g12a_aoclk_cec_pre, + &g12a_aoclk_cec_div, + &g12a_aoclk_cec_sel, + &g12a_aoclk_cec, + &g12a_aoclk_cts_rtc_oscin, + &g12a_aoclk_clk81, + &g12a_aoclk_saradc_mux, + &g12a_aoclk_saradc_div, + &g12a_aoclk_saradc_gate, +}; + +static const struct clk_hw_onecell_data g12a_aoclk_onecell_data = { + .hws = { + [CLKID_AO_AHB] = &g12a_aoclk_ahb.hw, + [CLKID_AO_IR_IN] = &g12a_aoclk_ir_in.hw, + [CLKID_AO_I2C_M0] = &g12a_aoclk_i2c_m0.hw, + [CLKID_AO_I2C_S0] = &g12a_aoclk_i2c_s0.hw, + [CLKID_AO_UART] = &g12a_aoclk_uart.hw, + [CLKID_AO_PROD_I2C] = &g12a_aoclk_prod_i2c.hw, + [CLKID_AO_UART2] = &g12a_aoclk_uart2.hw, + [CLKID_AO_IR_OUT] = &g12a_aoclk_ir_out.hw, + [CLKID_AO_SAR_ADC] = &g12a_aoclk_saradc.hw, + [CLKID_AO_MAILBOX] = &g12a_aoclk_mailbox.hw, + [CLKID_AO_M3] = &g12a_aoclk_m3.hw, + [CLKID_AO_AHB_SRAM] = &g12a_aoclk_ahb_sram.hw, + [CLKID_AO_RTI] = &g12a_aoclk_rti.hw, + [CLKID_AO_M4_FCLK] = &g12a_aoclk_m4_fclk.hw, + [CLKID_AO_M4_HCLK] = &g12a_aoclk_m4_hclk.hw, + [CLKID_AO_CLK81] = &g12a_aoclk_clk81.hw, + [CLKID_AO_SAR_ADC_SEL] = &g12a_aoclk_saradc_mux.hw, + [CLKID_AO_SAR_ADC_DIV] = &g12a_aoclk_saradc_div.hw, + [CLKID_AO_SAR_ADC_CLK] = &g12a_aoclk_saradc_gate.hw, + [CLKID_AO_CTS_OSCIN] = &g12a_aoclk_cts_oscin.hw, + [CLKID_AO_32K_PRE] = &g12a_aoclk_32k_by_oscin_pre.hw, + [CLKID_AO_32K_DIV] = &g12a_aoclk_32k_by_oscin_div.hw, + [CLKID_AO_32K_SEL] = &g12a_aoclk_32k_by_oscin_sel.hw, + [CLKID_AO_32K] = &g12a_aoclk_32k_by_oscin.hw, + [CLKID_AO_CEC_PRE] = &g12a_aoclk_cec_pre.hw, + [CLKID_AO_CEC_DIV] = &g12a_aoclk_cec_div.hw, + [CLKID_AO_CEC_SEL] = &g12a_aoclk_cec_sel.hw, + [CLKID_AO_CEC] = &g12a_aoclk_cec.hw, + [CLKID_AO_CTS_RTC_OSCIN] = &g12a_aoclk_cts_rtc_oscin.hw, + }, + .num = NR_CLKS, +}; + +static const struct meson_aoclk_input g12a_aoclk_inputs[] = { + { .name = "xtal", .required = true }, + { .name = "mpeg-clk", .required = true }, + { .name = "ext-32k-0", .required = false }, +}; + +static const struct meson_aoclk_data g12a_aoclkc_data = { + .reset_reg = AO_RTI_GEN_CNTL_REG0, + .num_reset = ARRAY_SIZE(g12a_aoclk_reset), + .reset = g12a_aoclk_reset, + .num_clks = ARRAY_SIZE(g12a_aoclk_regmap), + .clks = g12a_aoclk_regmap, + .hw_data = &g12a_aoclk_onecell_data, + .inputs = g12a_aoclk_inputs, + .num_inputs = ARRAY_SIZE(g12a_aoclk_inputs), + .input_prefix = IN_PREFIX, +}; + +static const struct of_device_id g12a_aoclkc_match_table[] = { + { + .compatible = "amlogic,meson-g12a-aoclkc", + .data = &g12a_aoclkc_data, + }, + { } +}; + +static struct platform_driver g12a_aoclkc_driver = { + .probe = meson_aoclkc_probe, + .driver = { + .name = "g12a-aoclkc", + .of_match_table = g12a_aoclkc_match_table, + }, +}; + +builtin_platform_driver(g12a_aoclkc_driver); diff --git a/drivers/clk/meson/g12a-aoclk.h b/drivers/clk/meson/g12a-aoclk.h new file mode 100644 index 000000000000..04b0d5506641 --- /dev/null +++ b/drivers/clk/meson/g12a-aoclk.h @@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#ifndef __G12A_AOCLKC_H +#define __G12A_AOCLKC_H + +/* + * CLKID index values + * + * These indices are entirely contrived and do not map onto the hardware. + * It has now been decided to expose everything by default in the DT header: + * include/dt-bindings/clock/g12a-aoclkc.h. Only the clocks ids we don't want + * to expose, such as the internal muxes and dividers of composite clocks, + * will remain defined here. + */ +#define CLKID_AO_SAR_ADC_SEL 16 +#define CLKID_AO_SAR_ADC_DIV 17 +#define CLKID_AO_CTS_OSCIN 19 +#define CLKID_AO_32K_PRE 20 +#define CLKID_AO_32K_DIV 21 +#define CLKID_AO_32K_SEL 22 +#define CLKID_AO_CEC_PRE 24 +#define CLKID_AO_CEC_DIV 25 +#define CLKID_AO_CEC_SEL 26 + +#define NR_CLKS 29 + +#include <dt-bindings/clock/g12a-aoclkc.h> +#include <dt-bindings/reset/g12a-aoclkc.h> + +#endif /* __G12A_AOCLKC_H */ -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 2/2] clk: meson: Add G12A AO Clock + Reset Controller @ 2019-02-12 16:28 ` Neil Armstrong 0 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-12 16:28 UTC (permalink / raw) To: jbrunet Cc: Neil Armstrong, linux-clk, linux-amlogic, linux-arm-kernel, linux-kernel Add the Amlogic G12A AO Clock and Reset controller driver handling generation of Always-On clocks : - AO Clocks and Reset for Always-On modules - 32K Generation for USB and CEC - SAR ADC controller clock Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- drivers/clk/meson/Kconfig | 2 + drivers/clk/meson/Makefile | 2 +- drivers/clk/meson/g12a-aoclk.c | 454 +++++++++++++++++++++++++++++++++ drivers/clk/meson/g12a-aoclk.h | 34 +++ 4 files changed, 491 insertions(+), 1 deletion(-) create mode 100644 drivers/clk/meson/g12a-aoclk.c create mode 100644 drivers/clk/meson/g12a-aoclk.h diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig index b72439315340..3858747f5438 100644 --- a/drivers/clk/meson/Kconfig +++ b/drivers/clk/meson/Kconfig @@ -98,8 +98,10 @@ config COMMON_CLK_G12A bool depends on ARCH_MESON select COMMON_CLK_MESON_REGMAP + select COMMON_CLK_MESON_DUALDIV select COMMON_CLK_MESON_MPLL select COMMON_CLK_MESON_PLL + select COMMON_CLK_MESON_AO_CLKC select COMMON_CLK_MESON_EE_CLKC select MFD_SYSCON help diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile index 32d17f18541e..021fc290e749 100644 --- a/drivers/clk/meson/Makefile +++ b/drivers/clk/meson/Makefile @@ -16,5 +16,5 @@ obj-$(CONFIG_COMMON_CLK_MESON_VID_PLL_DIV) += vid-pll-div.o obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o -obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o +obj-$(CONFIG_COMMON_CLK_G12A) += g12a.o g12a-aoclk.o obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o diff --git a/drivers/clk/meson/g12a-aoclk.c b/drivers/clk/meson/g12a-aoclk.c new file mode 100644 index 000000000000..1994e735396b --- /dev/null +++ b/drivers/clk/meson/g12a-aoclk.c @@ -0,0 +1,454 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Amlogic Meson-AXG Clock Controller Driver + * + * Copyright (c) 2016 Baylibre SAS. + * Author: Michael Turquette <mturquette@baylibre.com> + * + * Copyright (c) 2019 Baylibre SAS. + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ +#include <linux/clk-provider.h> +#include <linux/platform_device.h> +#include <linux/reset-controller.h> +#include <linux/mfd/syscon.h> +#include "meson-aoclk.h" +#include "g12a-aoclk.h" + +#include "clk-regmap.h" +#include "clk-dualdiv.h" + +#define IN_PREFIX "ao-in-" + +/* + * AO Configuration Clock registers offsets + * Register offsets from the data sheet must be multiplied by 4. + */ +#define AO_RTI_STATUS_REG3 0x0C +#define AO_RTI_PWR_CNTL_REG0 0x10 +#define AO_RTI_GEN_CNTL_REG0 0x40 +#define AO_CLK_GATE0 0x4c +#define AO_CLK_GATE0_SP 0x50 +#define AO_OSCIN_CNTL 0x58 +#define AO_CEC_CLK_CNTL_REG0 0x74 +#define AO_CEC_CLK_CNTL_REG1 0x78 +#define AO_SAR_CLK 0x90 +#define AO_RTC_ALT_CLK_CNTL0 0x94 +#define AO_RTC_ALT_CLK_CNTL1 0x98 + +/* + * Like every other peripheral clock gate in Amlogic Clock drivers, + * we are using CLK_IGNORE_UNUSED here, so we keep the state of the + * bootloader. The goal is to remove this flag at some point. + * Actually removing it will require some extensive test to be done safely. + */ +#define AXG_AO_GATE(_name, _reg, _bit) \ +static struct clk_regmap g12a_aoclk_##_name = { \ + .data = &(struct clk_regmap_gate_data) { \ + .offset = (_reg), \ + .bit_idx = (_bit), \ + }, \ + .hw.init = &(struct clk_init_data) { \ + .name = "g12a_ao_" #_name, \ + .ops = &clk_regmap_gate_ops, \ + .parent_names = (const char *[]){ IN_PREFIX "mpeg-clk" }, \ + .num_parents = 1, \ + .flags = CLK_IGNORE_UNUSED, \ + }, \ +} + +AXG_AO_GATE(ahb, AO_CLK_GATE0, 0); +AXG_AO_GATE(ir_in, AO_CLK_GATE0, 1); +AXG_AO_GATE(i2c_m0, AO_CLK_GATE0, 2); +AXG_AO_GATE(i2c_s0, AO_CLK_GATE0, 3); +AXG_AO_GATE(uart, AO_CLK_GATE0, 4); +AXG_AO_GATE(prod_i2c, AO_CLK_GATE0, 5); +AXG_AO_GATE(uart2, AO_CLK_GATE0, 6); +AXG_AO_GATE(ir_out, AO_CLK_GATE0, 7); +AXG_AO_GATE(saradc, AO_CLK_GATE0, 8); +AXG_AO_GATE(mailbox, AO_CLK_GATE0_SP, 0); +AXG_AO_GATE(m3, AO_CLK_GATE0_SP, 1); +AXG_AO_GATE(ahb_sram, AO_CLK_GATE0_SP, 2); +AXG_AO_GATE(rti, AO_CLK_GATE0_SP, 3); +AXG_AO_GATE(m4_fclk, AO_CLK_GATE0_SP, 4); +AXG_AO_GATE(m4_hclk, AO_CLK_GATE0_SP, 5); + +static struct clk_regmap g12a_aoclk_cts_oscin = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTI_PWR_CNTL_REG0, + .bit_idx = 14, + }, + .hw.init = &(struct clk_init_data){ + .name = "cts_oscin", + .ops = &clk_regmap_gate_ro_ops, + .parent_names = (const char *[]){ IN_PREFIX "xtal" }, + .num_parents = 1, + }, +}; + +static const struct meson_clk_dualdiv_param g12a_32k_div_table[] = { + { + .dual = 1, + .n1 = 733, + .m1 = 8, + .n2 = 732, + .m2 = 11, + }, {} +}; + +/* 32k_by_oscin clock */ + +static struct clk_regmap g12a_aoclk_32k_by_oscin_pre = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTC_ALT_CLK_CNTL0, + .bit_idx = 31, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_pre", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "cts_oscin" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin_div = { + .data = &(struct meson_clk_dualdiv_data){ + .n1 = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 0, + .width = 12, + }, + .n2 = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 12, + .width = 12, + }, + .m1 = { + .reg_off = AO_RTC_ALT_CLK_CNTL1, + .shift = 0, + .width = 12, + }, + .m2 = { + .reg_off = AO_RTC_ALT_CLK_CNTL1, + .shift = 12, + .width = 12, + }, + .dual = { + .reg_off = AO_RTC_ALT_CLK_CNTL0, + .shift = 28, + .width = 1, + }, + .table = g12a_32k_div_table, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_div", + .ops = &meson_clk_dualdiv_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_pre" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin_sel = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTC_ALT_CLK_CNTL1, + .mask = 0x1, + .shift = 24, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin_sel", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_div", + "g12a_ao_32k_by_oscin_pre" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_32k_by_oscin = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_RTC_ALT_CLK_CNTL0, + .bit_idx = 30, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_32k_by_oscin", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin_sel" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +/* cec clock */ + +static struct clk_regmap g12a_aoclk_cec_pre = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_CEC_CLK_CNTL_REG0, + .bit_idx = 31, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_pre", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "cts_oscin" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_cec_div = { + .data = &(struct meson_clk_dualdiv_data){ + .n1 = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 0, + .width = 12, + }, + .n2 = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 12, + .width = 12, + }, + .m1 = { + .reg_off = AO_CEC_CLK_CNTL_REG1, + .shift = 0, + .width = 12, + }, + .m2 = { + .reg_off = AO_CEC_CLK_CNTL_REG1, + .shift = 12, + .width = 12, + }, + .dual = { + .reg_off = AO_CEC_CLK_CNTL_REG0, + .shift = 28, + .width = 1, + }, + .table = g12a_32k_div_table, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_div", + .ops = &meson_clk_dualdiv_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_pre" }, + .num_parents = 1, + }, +}; + +static struct clk_regmap g12a_aoclk_cec_sel = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_CEC_CLK_CNTL_REG1, + .mask = 0x1, + .shift = 24, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec_sel", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_div", + "g12a_ao_cec_pre" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_cec = { + .data = &(struct clk_regmap_gate_data){ + .offset = AO_CEC_CLK_CNTL_REG0, + .bit_idx = 30, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cec", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_cec_sel" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_cts_rtc_oscin = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTI_PWR_CNTL_REG0, + .mask = 0x1, + .shift = 10, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_cts_rtc_oscin", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ "g12a_ao_32k_by_oscin", + IN_PREFIX "ext_32k-0" }, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_clk81 = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_RTI_PWR_CNTL_REG0, + .mask = 0x1, + .shift = 8, + .flags = CLK_MUX_ROUND_CLOSEST, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_clk81", + .ops = &clk_regmap_mux_ro_ops, + .parent_names = (const char *[]){ IN_PREFIX "mpeg-clk", + "g12a_ao_cts_rtc_oscin"}, + .num_parents = 2, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_mux = { + .data = &(struct clk_regmap_mux_data) { + .offset = AO_SAR_CLK, + .mask = 0x3, + .shift = 9, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_mux", + .ops = &clk_regmap_mux_ops, + .parent_names = (const char *[]){ IN_PREFIX "xtal", + "g12a_ao_clk81" }, + .num_parents = 2, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_div = { + .data = &(struct clk_regmap_div_data) { + .offset = AO_SAR_CLK, + .shift = 0, + .width = 8, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_div", + .ops = &clk_regmap_divider_ops, + .parent_names = (const char *[]){ "g12a_ao_saradc_mux" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static struct clk_regmap g12a_aoclk_saradc_gate = { + .data = &(struct clk_regmap_gate_data) { + .offset = AO_SAR_CLK, + .bit_idx = 8, + }, + .hw.init = &(struct clk_init_data){ + .name = "g12a_ao_saradc_gate", + .ops = &clk_regmap_gate_ops, + .parent_names = (const char *[]){ "g12a_ao_saradc_div" }, + .num_parents = 1, + .flags = CLK_SET_RATE_PARENT, + }, +}; + +static const unsigned int g12a_aoclk_reset[] = { + [RESET_AO_IR_IN] = 16, + [RESET_AO_UART] = 17, + [RESET_AO_I2C_M] = 18, + [RESET_AO_I2C_S] = 19, + [RESET_AO_SAR_ADC] = 20, + [RESET_AO_UART2] = 22, + [RESET_AO_IR_OUT] = 23, +}; + +static struct clk_regmap *g12a_aoclk_regmap[] = { + &g12a_aoclk_ahb, + &g12a_aoclk_ir_in, + &g12a_aoclk_i2c_m0, + &g12a_aoclk_i2c_s0, + &g12a_aoclk_uart, + &g12a_aoclk_prod_i2c, + &g12a_aoclk_uart2, + &g12a_aoclk_ir_out, + &g12a_aoclk_saradc, + &g12a_aoclk_mailbox, + &g12a_aoclk_m3, + &g12a_aoclk_ahb_sram, + &g12a_aoclk_rti, + &g12a_aoclk_m4_fclk, + &g12a_aoclk_m4_hclk, + &g12a_aoclk_cts_oscin, + &g12a_aoclk_32k_by_oscin_pre, + &g12a_aoclk_32k_by_oscin_div, + &g12a_aoclk_32k_by_oscin_sel, + &g12a_aoclk_32k_by_oscin, + &g12a_aoclk_cec_pre, + &g12a_aoclk_cec_div, + &g12a_aoclk_cec_sel, + &g12a_aoclk_cec, + &g12a_aoclk_cts_rtc_oscin, + &g12a_aoclk_clk81, + &g12a_aoclk_saradc_mux, + &g12a_aoclk_saradc_div, + &g12a_aoclk_saradc_gate, +}; + +static const struct clk_hw_onecell_data g12a_aoclk_onecell_data = { + .hws = { + [CLKID_AO_AHB] = &g12a_aoclk_ahb.hw, + [CLKID_AO_IR_IN] = &g12a_aoclk_ir_in.hw, + [CLKID_AO_I2C_M0] = &g12a_aoclk_i2c_m0.hw, + [CLKID_AO_I2C_S0] = &g12a_aoclk_i2c_s0.hw, + [CLKID_AO_UART] = &g12a_aoclk_uart.hw, + [CLKID_AO_PROD_I2C] = &g12a_aoclk_prod_i2c.hw, + [CLKID_AO_UART2] = &g12a_aoclk_uart2.hw, + [CLKID_AO_IR_OUT] = &g12a_aoclk_ir_out.hw, + [CLKID_AO_SAR_ADC] = &g12a_aoclk_saradc.hw, + [CLKID_AO_MAILBOX] = &g12a_aoclk_mailbox.hw, + [CLKID_AO_M3] = &g12a_aoclk_m3.hw, + [CLKID_AO_AHB_SRAM] = &g12a_aoclk_ahb_sram.hw, + [CLKID_AO_RTI] = &g12a_aoclk_rti.hw, + [CLKID_AO_M4_FCLK] = &g12a_aoclk_m4_fclk.hw, + [CLKID_AO_M4_HCLK] = &g12a_aoclk_m4_hclk.hw, + [CLKID_AO_CLK81] = &g12a_aoclk_clk81.hw, + [CLKID_AO_SAR_ADC_SEL] = &g12a_aoclk_saradc_mux.hw, + [CLKID_AO_SAR_ADC_DIV] = &g12a_aoclk_saradc_div.hw, + [CLKID_AO_SAR_ADC_CLK] = &g12a_aoclk_saradc_gate.hw, + [CLKID_AO_CTS_OSCIN] = &g12a_aoclk_cts_oscin.hw, + [CLKID_AO_32K_PRE] = &g12a_aoclk_32k_by_oscin_pre.hw, + [CLKID_AO_32K_DIV] = &g12a_aoclk_32k_by_oscin_div.hw, + [CLKID_AO_32K_SEL] = &g12a_aoclk_32k_by_oscin_sel.hw, + [CLKID_AO_32K] = &g12a_aoclk_32k_by_oscin.hw, + [CLKID_AO_CEC_PRE] = &g12a_aoclk_cec_pre.hw, + [CLKID_AO_CEC_DIV] = &g12a_aoclk_cec_div.hw, + [CLKID_AO_CEC_SEL] = &g12a_aoclk_cec_sel.hw, + [CLKID_AO_CEC] = &g12a_aoclk_cec.hw, + [CLKID_AO_CTS_RTC_OSCIN] = &g12a_aoclk_cts_rtc_oscin.hw, + }, + .num = NR_CLKS, +}; + +static const struct meson_aoclk_input g12a_aoclk_inputs[] = { + { .name = "xtal", .required = true }, + { .name = "mpeg-clk", .required = true }, + { .name = "ext-32k-0", .required = false }, +}; + +static const struct meson_aoclk_data g12a_aoclkc_data = { + .reset_reg = AO_RTI_GEN_CNTL_REG0, + .num_reset = ARRAY_SIZE(g12a_aoclk_reset), + .reset = g12a_aoclk_reset, + .num_clks = ARRAY_SIZE(g12a_aoclk_regmap), + .clks = g12a_aoclk_regmap, + .hw_data = &g12a_aoclk_onecell_data, + .inputs = g12a_aoclk_inputs, + .num_inputs = ARRAY_SIZE(g12a_aoclk_inputs), + .input_prefix = IN_PREFIX, +}; + +static const struct of_device_id g12a_aoclkc_match_table[] = { + { + .compatible = "amlogic,meson-g12a-aoclkc", + .data = &g12a_aoclkc_data, + }, + { } +}; + +static struct platform_driver g12a_aoclkc_driver = { + .probe = meson_aoclkc_probe, + .driver = { + .name = "g12a-aoclkc", + .of_match_table = g12a_aoclkc_match_table, + }, +}; + +builtin_platform_driver(g12a_aoclkc_driver); diff --git a/drivers/clk/meson/g12a-aoclk.h b/drivers/clk/meson/g12a-aoclk.h new file mode 100644 index 000000000000..04b0d5506641 --- /dev/null +++ b/drivers/clk/meson/g12a-aoclk.h @@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#ifndef __G12A_AOCLKC_H +#define __G12A_AOCLKC_H + +/* + * CLKID index values + * + * These indices are entirely contrived and do not map onto the hardware. + * It has now been decided to expose everything by default in the DT header: + * include/dt-bindings/clock/g12a-aoclkc.h. Only the clocks ids we don't want + * to expose, such as the internal muxes and dividers of composite clocks, + * will remain defined here. + */ +#define CLKID_AO_SAR_ADC_SEL 16 +#define CLKID_AO_SAR_ADC_DIV 17 +#define CLKID_AO_CTS_OSCIN 19 +#define CLKID_AO_32K_PRE 20 +#define CLKID_AO_32K_DIV 21 +#define CLKID_AO_32K_SEL 22 +#define CLKID_AO_CEC_PRE 24 +#define CLKID_AO_CEC_DIV 25 +#define CLKID_AO_CEC_SEL 26 + +#define NR_CLKS 29 + +#include <dt-bindings/clock/g12a-aoclkc.h> +#include <dt-bindings/reset/g12a-aoclkc.h> + +#endif /* __G12A_AOCLKC_H */ -- 2.20.1 ^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller 2019-02-12 16:28 ` Neil Armstrong (?) @ 2019-02-13 8:38 ` Jerome Brunet -1 siblings, 0 replies; 19+ messages in thread From: Jerome Brunet @ 2019-02-13 8:38 UTC (permalink / raw) To: Neil Armstrong; +Cc: linux-amlogic, linux-clk, linux-arm-kernel, linux-kernel On Tue, 2019-02-12 at 17:28 +0100, Neil Armstrong wrote: > This patchset add support for the Amlogic G12A SoC family Always-On > clock and reset controller. > > This adds support for clocks on the Always-On domain like : > - Always-On UARTS & I2C Controllers > - CEC Controllers > - SARADC source and bus clock > - Infrared Decoder/Encoder bus clock > - USB 32K reference clock > > This also adds resets lines for : > - Always-On UARTS & I2C Controllers > - SARADC, Infrared Decoder/Encoder > > This patchset depends on the ("clk: meson: rework drivers dependencies") > from Jerome Brunet at [1]. > > Changes from v1 at [2]: > - Moved unused bindings ID out of the dt-bindings header > - Added comment about CLK_IGNORE_UNUSED > > [1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com > [2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com > > Neil Armstrong (2): > dt-bindings: clk: add G12A AO Clock and Reset Bindings > clk: meson: Add G12A AO Clock + Reset Controller Acked-by: Jerome Brunet <jbrunet@baylibre.com> > > .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + > drivers/clk/meson/Kconfig | 2 + > drivers/clk/meson/Makefile | 2 +- > drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++ > drivers/clk/meson/g12a-aoclk.h | 34 ++ > include/dt-bindings/clock/g12a-aoclkc.h | 34 ++ > include/dt-bindings/reset/g12a-aoclkc.h | 18 + > 7 files changed, 544 insertions(+), 1 deletion(-) > create mode 100644 drivers/clk/meson/g12a-aoclk.c > create mode 100644 drivers/clk/meson/g12a-aoclk.h > create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h > create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h > _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller @ 2019-02-13 8:38 ` Jerome Brunet 0 siblings, 0 replies; 19+ messages in thread From: Jerome Brunet @ 2019-02-13 8:38 UTC (permalink / raw) To: Neil Armstrong; +Cc: linux-amlogic, linux-clk, linux-arm-kernel, linux-kernel On Tue, 2019-02-12 at 17:28 +0100, Neil Armstrong wrote: > This patchset add support for the Amlogic G12A SoC family Always-On > clock and reset controller. > > This adds support for clocks on the Always-On domain like : > - Always-On UARTS & I2C Controllers > - CEC Controllers > - SARADC source and bus clock > - Infrared Decoder/Encoder bus clock > - USB 32K reference clock > > This also adds resets lines for : > - Always-On UARTS & I2C Controllers > - SARADC, Infrared Decoder/Encoder > > This patchset depends on the ("clk: meson: rework drivers dependencies") > from Jerome Brunet at [1]. > > Changes from v1 at [2]: > - Moved unused bindings ID out of the dt-bindings header > - Added comment about CLK_IGNORE_UNUSED > > [1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com > [2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com > > Neil Armstrong (2): > dt-bindings: clk: add G12A AO Clock and Reset Bindings > clk: meson: Add G12A AO Clock + Reset Controller Acked-by: Jerome Brunet <jbrunet@baylibre.com> > > .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + > drivers/clk/meson/Kconfig | 2 + > drivers/clk/meson/Makefile | 2 +- > drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++ > drivers/clk/meson/g12a-aoclk.h | 34 ++ > include/dt-bindings/clock/g12a-aoclkc.h | 34 ++ > include/dt-bindings/reset/g12a-aoclkc.h | 18 + > 7 files changed, 544 insertions(+), 1 deletion(-) > create mode 100644 drivers/clk/meson/g12a-aoclk.c > create mode 100644 drivers/clk/meson/g12a-aoclk.h > create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h > create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller @ 2019-02-13 8:38 ` Jerome Brunet 0 siblings, 0 replies; 19+ messages in thread From: Jerome Brunet @ 2019-02-13 8:38 UTC (permalink / raw) To: Neil Armstrong; +Cc: linux-clk, linux-amlogic, linux-arm-kernel, linux-kernel On Tue, 2019-02-12 at 17:28 +0100, Neil Armstrong wrote: > This patchset add support for the Amlogic G12A SoC family Always-On > clock and reset controller. > > This adds support for clocks on the Always-On domain like : > - Always-On UARTS & I2C Controllers > - CEC Controllers > - SARADC source and bus clock > - Infrared Decoder/Encoder bus clock > - USB 32K reference clock > > This also adds resets lines for : > - Always-On UARTS & I2C Controllers > - SARADC, Infrared Decoder/Encoder > > This patchset depends on the ("clk: meson: rework drivers dependencies") > from Jerome Brunet at [1]. > > Changes from v1 at [2]: > - Moved unused bindings ID out of the dt-bindings header > - Added comment about CLK_IGNORE_UNUSED > > [1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com > [2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com > > Neil Armstrong (2): > dt-bindings: clk: add G12A AO Clock and Reset Bindings > clk: meson: Add G12A AO Clock + Reset Controller Acked-by: Jerome Brunet <jbrunet@baylibre.com> > > .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + > drivers/clk/meson/Kconfig | 2 + > drivers/clk/meson/Makefile | 2 +- > drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++ > drivers/clk/meson/g12a-aoclk.h | 34 ++ > include/dt-bindings/clock/g12a-aoclkc.h | 34 ++ > include/dt-bindings/reset/g12a-aoclkc.h | 18 + > 7 files changed, 544 insertions(+), 1 deletion(-) > create mode 100644 drivers/clk/meson/g12a-aoclk.c > create mode 100644 drivers/clk/meson/g12a-aoclk.h > create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h > create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h > ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller 2019-02-13 8:38 ` Jerome Brunet (?) @ 2019-02-13 9:00 ` Neil Armstrong -1 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-13 9:00 UTC (permalink / raw) To: Jerome Brunet; +Cc: linux-amlogic, linux-clk, linux-arm-kernel, linux-kernel On 13/02/2019 09:38, Jerome Brunet wrote: > On Tue, 2019-02-12 at 17:28 +0100, Neil Armstrong wrote: >> This patchset add support for the Amlogic G12A SoC family Always-On >> clock and reset controller. >> >> This adds support for clocks on the Always-On domain like : >> - Always-On UARTS & I2C Controllers >> - CEC Controllers >> - SARADC source and bus clock >> - Infrared Decoder/Encoder bus clock >> - USB 32K reference clock >> >> This also adds resets lines for : >> - Always-On UARTS & I2C Controllers >> - SARADC, Infrared Decoder/Encoder >> >> This patchset depends on the ("clk: meson: rework drivers dependencies") >> from Jerome Brunet at [1]. >> >> Changes from v1 at [2]: >> - Moved unused bindings ID out of the dt-bindings header >> - Added comment about CLK_IGNORE_UNUSED >> >> [1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com >> [2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com >> >> Neil Armstrong (2): >> dt-bindings: clk: add G12A AO Clock and Reset Bindings >> clk: meson: Add G12A AO Clock + Reset Controller > > Acked-by: Jerome Brunet <jbrunet@baylibre.com> > >> >> .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + >> drivers/clk/meson/Kconfig | 2 + >> drivers/clk/meson/Makefile | 2 +- >> drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++ >> drivers/clk/meson/g12a-aoclk.h | 34 ++ >> include/dt-bindings/clock/g12a-aoclkc.h | 34 ++ >> include/dt-bindings/reset/g12a-aoclkc.h | 18 + >> 7 files changed, 544 insertions(+), 1 deletion(-) >> create mode 100644 drivers/clk/meson/g12a-aoclk.c >> create mode 100644 drivers/clk/meson/g12a-aoclk.h >> create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h >> create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h >> > > Applied to next/drivers for Linux 5.1-rc1 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller @ 2019-02-13 9:00 ` Neil Armstrong 0 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-13 9:00 UTC (permalink / raw) To: Jerome Brunet; +Cc: linux-amlogic, linux-clk, linux-arm-kernel, linux-kernel On 13/02/2019 09:38, Jerome Brunet wrote: > On Tue, 2019-02-12 at 17:28 +0100, Neil Armstrong wrote: >> This patchset add support for the Amlogic G12A SoC family Always-On >> clock and reset controller. >> >> This adds support for clocks on the Always-On domain like : >> - Always-On UARTS & I2C Controllers >> - CEC Controllers >> - SARADC source and bus clock >> - Infrared Decoder/Encoder bus clock >> - USB 32K reference clock >> >> This also adds resets lines for : >> - Always-On UARTS & I2C Controllers >> - SARADC, Infrared Decoder/Encoder >> >> This patchset depends on the ("clk: meson: rework drivers dependencies") >> from Jerome Brunet at [1]. >> >> Changes from v1 at [2]: >> - Moved unused bindings ID out of the dt-bindings header >> - Added comment about CLK_IGNORE_UNUSED >> >> [1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com >> [2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com >> >> Neil Armstrong (2): >> dt-bindings: clk: add G12A AO Clock and Reset Bindings >> clk: meson: Add G12A AO Clock + Reset Controller > > Acked-by: Jerome Brunet <jbrunet@baylibre.com> > >> >> .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + >> drivers/clk/meson/Kconfig | 2 + >> drivers/clk/meson/Makefile | 2 +- >> drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++ >> drivers/clk/meson/g12a-aoclk.h | 34 ++ >> include/dt-bindings/clock/g12a-aoclkc.h | 34 ++ >> include/dt-bindings/reset/g12a-aoclkc.h | 18 + >> 7 files changed, 544 insertions(+), 1 deletion(-) >> create mode 100644 drivers/clk/meson/g12a-aoclk.c >> create mode 100644 drivers/clk/meson/g12a-aoclk.h >> create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h >> create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h >> > > Applied to next/drivers for Linux 5.1-rc1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller @ 2019-02-13 9:00 ` Neil Armstrong 0 siblings, 0 replies; 19+ messages in thread From: Neil Armstrong @ 2019-02-13 9:00 UTC (permalink / raw) To: Jerome Brunet; +Cc: linux-clk, linux-amlogic, linux-arm-kernel, linux-kernel On 13/02/2019 09:38, Jerome Brunet wrote: > On Tue, 2019-02-12 at 17:28 +0100, Neil Armstrong wrote: >> This patchset add support for the Amlogic G12A SoC family Always-On >> clock and reset controller. >> >> This adds support for clocks on the Always-On domain like : >> - Always-On UARTS & I2C Controllers >> - CEC Controllers >> - SARADC source and bus clock >> - Infrared Decoder/Encoder bus clock >> - USB 32K reference clock >> >> This also adds resets lines for : >> - Always-On UARTS & I2C Controllers >> - SARADC, Infrared Decoder/Encoder >> >> This patchset depends on the ("clk: meson: rework drivers dependencies") >> from Jerome Brunet at [1]. >> >> Changes from v1 at [2]: >> - Moved unused bindings ID out of the dt-bindings header >> - Added comment about CLK_IGNORE_UNUSED >> >> [1] https://lkml.kernel.org/r/20190201125841.26785-1-jbrunet@baylibre.com >> [2] https://lkml.kernel.org/r/20190204091331.9298-1-narmstrong@baylibre.com >> >> Neil Armstrong (2): >> dt-bindings: clk: add G12A AO Clock and Reset Bindings >> clk: meson: Add G12A AO Clock + Reset Controller > > Acked-by: Jerome Brunet <jbrunet@baylibre.com> > >> >> .../bindings/clock/amlogic,gxbb-aoclkc.txt | 1 + >> drivers/clk/meson/Kconfig | 2 + >> drivers/clk/meson/Makefile | 2 +- >> drivers/clk/meson/g12a-aoclk.c | 454 ++++++++++++++++++ >> drivers/clk/meson/g12a-aoclk.h | 34 ++ >> include/dt-bindings/clock/g12a-aoclkc.h | 34 ++ >> include/dt-bindings/reset/g12a-aoclkc.h | 18 + >> 7 files changed, 544 insertions(+), 1 deletion(-) >> create mode 100644 drivers/clk/meson/g12a-aoclk.c >> create mode 100644 drivers/clk/meson/g12a-aoclk.h >> create mode 100644 include/dt-bindings/clock/g12a-aoclkc.h >> create mode 100644 include/dt-bindings/reset/g12a-aoclkc.h >> > > Applied to next/drivers for Linux 5.1-rc1 ^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2019-02-18 20:02 UTC | newest] Thread overview: 19+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2019-02-12 16:28 [PATCH v2 0/2] clk: meson: Add G12A AO Clock + Reset Controller Neil Armstrong 2019-02-12 16:28 ` Neil Armstrong 2019-02-12 16:28 ` Neil Armstrong 2019-02-12 16:28 ` [PATCH v2 1/2] dt-bindings: clk: add G12A AO Clock and Reset Bindings Neil Armstrong 2019-02-12 16:28 ` Neil Armstrong 2019-02-12 16:28 ` Neil Armstrong 2019-02-18 20:02 ` Rob Herring 2019-02-18 20:02 ` Rob Herring 2019-02-18 20:02 ` Rob Herring 2019-02-18 20:02 ` Rob Herring 2019-02-12 16:28 ` [PATCH v2 2/2] clk: meson: Add G12A AO Clock + Reset Controller Neil Armstrong 2019-02-12 16:28 ` Neil Armstrong 2019-02-12 16:28 ` Neil Armstrong 2019-02-13 8:38 ` [PATCH v2 0/2] " Jerome Brunet 2019-02-13 8:38 ` Jerome Brunet 2019-02-13 8:38 ` Jerome Brunet 2019-02-13 9:00 ` Neil Armstrong 2019-02-13 9:00 ` Neil Armstrong 2019-02-13 9:00 ` Neil Armstrong
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.