[linux dev-5.0 v1 1/4] dt-binding: peci: add NPCM PECI documentation

[linux dev-5.0 v1 1/4] dt-binding: peci: add NPCM PECI documentation

[Tomer Maimon]

Added device tree binding documentation for Nuvoton BMC
NPCM Platform Environment Control Interface(PECI).

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 .../devicetree/bindings/peci/peci-npcm.txt         | 38 ++++++++++++++++++++++
 1 file changed, 38 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/peci/peci-npcm.txt

diff --git a/Documentation/devicetree/bindings/peci/peci-npcm.txt b/Documentation/devicetree/bindings/peci/peci-npcm.txt
new file mode 100644
index 000000000000..ea5bead7e76a
--- /dev/null
+++ b/Documentation/devicetree/bindings/peci/peci-npcm.txt
@@ -0,0 +1,38 @@
+Nuvoton NPCM Platform Environment Control Interface (PECI) bus
+
+Required properties:
+- compatible        : "nuvoton,npcm750-peci" for the NPCM7XX BMC.
+- reg               : specifies PECI physical base address and size of the registers.
+- #address-cells    : Should be <1> required to define a client address.
+- #size-cells       : Should be <0> required to define a client address.
+- interrupts        : Contain the PECI interrupt with flags for falling edge.
+- clocks            : phandle of PECI reference clock.
+
+Optional properties:
+- cmd-timeout-ms    : Command timeout in units of ms.
+                      1 ~ 60000 (default: 1000)
+- pull-down         : Defines the PECI I/O internal pull down operation.
+		      0 - pull down always enable (default)
+		      1 - pull down only during transactions.
+		      2 - pull down always disable.
+- host-neg-bit-rate : Define host negotiation bit rate divider.
+                      the host negotiation bit rate calculate with formula:
+                      clock frequency[Hz] / [4 x {host-neg-bit-rate + 1}]
+		      7 ~ 31 (default: 15)
+- high-volt-range   : Adapts PECI I/O interface to voltage range, the property
+                      is a boolean parameter define as follow:
+		      false - PECI I/O interface voltage range of 0.8-1.06V. (default)
+		      true - PECI I/O interface voltage range of 0.95-1.26V.
+
+Example:
+	peci: peci-bus@100000 {
+		compatible = "nuvoton,npcm750-peci";
+		reg = <0x100000 0x200>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk NPCM7XX_CLK_APB3>;
+		cmd-timeout-ms = <1000>;
+		pull-down = <0>;
+		host-neg-bit-rate = <15>;
+	};
-- 
2.14.1

[linux dev-5.0 v1 2/4] peci: npcm: add NPCM PECI driver

[Tomer Maimon]

Add Nuvoton NPCM BMC Platform Environment
Control Interface(PECI) driver.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 drivers/peci/Kconfig     |  11 ++
 drivers/peci/Makefile    |   1 +
 drivers/peci/peci-npcm.c | 410 +++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 422 insertions(+)
 create mode 100644 drivers/peci/peci-npcm.c

diff --git a/drivers/peci/Kconfig b/drivers/peci/Kconfig
index 9e9845ebcff4..7293108fb543 100644
--- a/drivers/peci/Kconfig
+++ b/drivers/peci/Kconfig
@@ -34,6 +34,17 @@ config PECI_ASPEED
 	  This support is also available as a module.  If so, the module
 	  will be called peci-aspeed.
 
+config PECI_NPCM
+	tristate "Nuvoton NPCM PECI support"
+	select REGMAP_MMIO
+	depends on OF
+	depends on ARCH_NPCM || COMPILE_TEST
+	help
+	  Say Y here if you want support for the Platform Environment Control
+	  Interface (PECI) bus adapter driver on the Nuvoton NPCM SoCs.
+
+	  This support is also available as a module. If so, the module
+	  will be called peci-npcm.
 endmenu
 
 endif # PECI
diff --git a/drivers/peci/Makefile b/drivers/peci/Makefile
index 886285e69765..3326da54a21a 100644
--- a/drivers/peci/Makefile
+++ b/drivers/peci/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_PECI)		+= peci-core.o
 
 # Hardware specific bus drivers
 obj-$(CONFIG_PECI_ASPEED)	+= peci-aspeed.o
+obj-$(CONFIG_PECI_NPCM)		+= peci-npcm.o
diff --git a/drivers/peci/peci-npcm.c b/drivers/peci/peci-npcm.c
new file mode 100644
index 000000000000..f632365b1416
--- /dev/null
+++ b/drivers/peci/peci-npcm.c
@@ -0,0 +1,410 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 Nuvoton Technology corporation.
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/peci.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+#include <linux/reset.h>
+
+/* NPCM7xx GCR module */
+#define NPCM7XX_INTCR3_OFFSET		0x9C
+#define NPCM7XX_INTCR3_PECIVSEL		BIT(19)
+
+/* NPCM PECI Registers */
+#define NPCM_PECI_CTL_STS	0x00
+#define NPCM_PECI_RD_LENGTH	0x04
+#define NPCM_PECI_ADDR		0x08
+#define NPCM_PECI_CMD		0x0C
+#define NPCM_PECI_CTL2		0x10
+#define NPCM_PECI_WR_LENGTH	0x1C
+#define NPCM_PECI_PDDR		0x2C
+#define NPCM_PECI_DAT_INOUT(n)	(0x100 + ((n) * 4))
+
+#define NPCM_PECI_MAX_REG	0x200
+
+/* NPCM_PECI_CTL_STS - 0x00 : Control Register */
+#define NPCM_PECI_CTRL_DONE_INT_EN	BIT(6)
+#define NPCM_PECI_CTRL_ABRT_ERR		BIT(4)
+#define NPCM_PECI_CTRL_CRC_ERR		BIT(3)
+#define NPCM_PECI_CTRL_DONE		BIT(1)
+#define NPCM_PECI_CTRL_START_BUSY	BIT(0)
+
+/* NPCM_PECI_RD_LENGTH - 0x04 : Command Register */
+#define NPCM_PECI_RD_LEN_MASK		GENMASK(6, 0)
+
+/* NPCM_PECI_CMD - 0x10 : Command Register */
+#define NPCM_PECI_CTL2_MASK		GENMASK(7, 6)
+
+/* NPCM_PECI_WR_LENGTH - 0x1C : Command Register */
+#define NPCM_PECI_WR_LEN_MASK		GENMASK(6, 0)
+
+/* NPCM_PECI_PDDR - 0x2C : Command Register */
+#define NPCM_PECI_PDDR_MASK		GENMASK(4, 0)
+
+#define NPCM_PECI_INT_MASK	(NPCM_PECI_CTRL_ABRT_ERR | \
+				NPCM_PECI_CTRL_CRC_ERR | \
+				NPCM_PECI_CTRL_DONE)
+
+#define NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC	50000
+#define NPCM_PECI_IDLE_CHECK_INTERVAL_USEC	10000
+#define NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT	1000
+#define NPCM_PECI_CMD_TIMEOUT_MS_MAX		60000
+#define NPCM_PECI_HOST_NEG_BIT_RATE_MAX		31
+#define NPCM_PECI_HOST_NEG_BIT_RATE_MIN		7
+#define NPCM_PECI_HOST_NEG_BIT_RATE_DEFAULT	15
+#define NPCM_PECI_PULL_DOWN_DEFAULT		0
+#define NPCM_PECI_PULL_DOWN_MAX			2
+
+struct npcm_peci {
+	u32			cmd_timeout_ms;
+	u32			host_bit_rate;
+	struct completion	xfer_complete;
+	struct regmap		*gcr_regmap;
+	struct peci_adapter	*adapter;
+	struct regmap		*regmap;
+	u32			status;
+	spinlock_t		lock; /* to sync completion status handling */
+	struct device		*dev;
+	struct clk		*clk;
+	int			irq;
+};
+
+static int npcm_peci_xfer_native(struct npcm_peci *priv,
+				 struct peci_xfer_msg *msg)
+{
+	long err, timeout = msecs_to_jiffies(priv->cmd_timeout_ms);
+	unsigned long flags;
+	unsigned int msg_rd;
+	u32 cmd_sts;
+	int i, rc;
+
+	/* Check command sts and bus idle state */
+	rc = regmap_read_poll_timeout(priv->regmap, NPCM_PECI_CTL_STS, cmd_sts,
+				      !(cmd_sts & NPCM_PECI_CTRL_START_BUSY),
+				      NPCM_PECI_IDLE_CHECK_INTERVAL_USEC,
+				      NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC);
+	if (rc)
+		return rc; /* -ETIMEDOUT */
+
+	spin_lock_irqsave(&priv->lock, flags);
+	reinit_completion(&priv->xfer_complete);
+
+	regmap_write(priv->regmap, NPCM_PECI_ADDR, msg->addr);
+	regmap_write(priv->regmap, NPCM_PECI_RD_LENGTH,
+		     NPCM_PECI_WR_LEN_MASK & msg->rx_len);
+	regmap_write(priv->regmap, NPCM_PECI_WR_LENGTH,
+		     NPCM_PECI_WR_LEN_MASK & msg->tx_len);
+
+	if (msg->tx_len) {
+		regmap_write(priv->regmap, NPCM_PECI_CMD, msg->tx_buf[0]);
+
+		for (i = 0; i < (msg->tx_len - 1); i++)
+			regmap_write(priv->regmap, NPCM_PECI_DAT_INOUT(i),
+				     msg->tx_buf[i + 1]);
+	}
+
+	priv->status = 0;
+	regmap_update_bits(priv->regmap, NPCM_PECI_CTL_STS,
+			   NPCM_PECI_CTRL_START_BUSY,
+			   NPCM_PECI_CTRL_START_BUSY);
+
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	err = wait_for_completion_interruptible_timeout(&priv->xfer_complete,
+							timeout);
+
+	spin_lock_irqsave(&priv->lock, flags);
+
+	regmap_write(priv->regmap, NPCM_PECI_CMD, 0);
+
+	if (err <= 0 || priv->status  != NPCM_PECI_CTRL_DONE) {
+		if (err < 0) { /* -ERESTARTSYS */
+			rc = (int)err;
+			goto err_irqrestore;
+		} else if (err == 0) {
+			dev_dbg(priv->dev, "Timeout waiting for a response!\n");
+			rc = -ETIMEDOUT;
+			goto err_irqrestore;
+		}
+
+		dev_dbg(priv->dev, "No valid response!\n");
+		rc = -EIO;
+		goto err_irqrestore;
+	}
+
+	for (i = 0; i < msg->rx_len; i++) {
+		regmap_read(priv->regmap, NPCM_PECI_DAT_INOUT(i), &msg_rd);
+		msg->rx_buf[i] = (u8)msg_rd;
+	}
+
+err_irqrestore:
+	spin_unlock_irqrestore(&priv->lock, flags);
+	return rc;
+}
+
+static irqreturn_t npcm_peci_irq_handler(int irq, void *arg)
+{
+	struct npcm_peci *priv = arg;
+	u32 status_ack = 0;
+	u32 status;
+
+	spin_lock(&priv->lock);
+	regmap_read(priv->regmap, NPCM_PECI_CTL_STS, &status);
+	priv->status |= (status & NPCM_PECI_INT_MASK);
+
+	if (status & NPCM_PECI_CTRL_CRC_ERR) {
+		dev_dbg(priv->dev, "PECI_INT_W_FCS_BAD\n");
+		status_ack |= NPCM_PECI_CTRL_CRC_ERR;
+	}
+
+	if (status & NPCM_PECI_CTRL_ABRT_ERR) {
+		dev_dbg(priv->dev, "NPCM_PECI_CTRL_ABRT_ERR\n");
+		status_ack |= NPCM_PECI_CTRL_ABRT_ERR;
+	}
+
+	/*
+	 * All commands should be ended up with a NPCM_PECI_CTRL_DONE
+	 * bit set even in an error case.
+	 */
+	if (status & NPCM_PECI_CTRL_DONE) {
+		dev_dbg(priv->dev, "NPCM_PECI_CTRL_DONE\n");
+		status_ack |= NPCM_PECI_CTRL_DONE;
+		complete(&priv->xfer_complete);
+	}
+
+	regmap_write_bits(priv->regmap, NPCM_PECI_CTL_STS,
+			  NPCM_PECI_INT_MASK, status_ack);
+
+	spin_unlock(&priv->lock);
+	return IRQ_HANDLED;
+}
+
+static int npcm_peci_init_ctrl(struct npcm_peci *priv)
+{
+	u32 cmd_sts, host_neg_bit_rate = 0, pull_down = 0;
+	int ret;
+	bool volt;
+
+	priv->clk = devm_clk_get(priv->dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(priv->dev, "Failed to get clk source.\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret) {
+		dev_err(priv->dev, "Failed to enable clock.\n");
+		return ret;
+	}
+
+	ret = of_property_read_u32(priv->dev->of_node, "cmd-timeout-ms",
+				   &priv->cmd_timeout_ms);
+	if (ret || priv->cmd_timeout_ms > NPCM_PECI_CMD_TIMEOUT_MS_MAX ||
+	    priv->cmd_timeout_ms == 0) {
+		if (ret)
+			dev_warn(priv->dev,
+				 "cmd-timeout-ms not found, use default : %u\n",
+				 NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT);
+		else
+			dev_warn(priv->dev,
+				 "Invalid cmd-timeout-ms : %u. Use default : %u\n",
+				 priv->cmd_timeout_ms,
+				 NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT);
+
+		priv->cmd_timeout_ms = NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT;
+	}
+
+	if (of_device_is_compatible(priv->dev->of_node,
+				    "nuvoton,npcm750-peci")) {
+		priv->gcr_regmap = syscon_regmap_lookup_by_compatible
+			("nuvoton,npcm750-gcr");
+		if (!IS_ERR(priv->gcr_regmap)) {
+			volt = of_property_read_bool(priv->dev->of_node,
+						     "high-volt-range");
+			if (volt)
+				regmap_update_bits(priv->gcr_regmap,
+						   NPCM7XX_INTCR3_OFFSET,
+						   NPCM7XX_INTCR3_PECIVSEL,
+						   NPCM7XX_INTCR3_PECIVSEL);
+			else
+				regmap_update_bits(priv->gcr_regmap,
+						   NPCM7XX_INTCR3_OFFSET,
+						   NPCM7XX_INTCR3_PECIVSEL, 0);
+		}
+	}
+
+	ret = of_property_read_u32(priv->dev->of_node, "pull-down",
+				   &pull_down);
+	if (ret || pull_down > NPCM_PECI_PULL_DOWN_MAX) {
+		if (ret)
+			dev_warn(priv->dev,
+				 "pull-down not found, use default : %u\n",
+				 NPCM_PECI_PULL_DOWN_DEFAULT);
+		else
+			dev_warn(priv->dev,
+				 "Invalid pull-down : %u. Use default : %u\n",
+				 pull_down,
+				 NPCM_PECI_PULL_DOWN_DEFAULT);
+		pull_down = NPCM_PECI_PULL_DOWN_DEFAULT;
+	}
+
+	regmap_update_bits(priv->regmap, NPCM_PECI_CTL2, NPCM_PECI_CTL2_MASK,
+			   pull_down << 6);
+
+	ret = of_property_read_u32(priv->dev->of_node, "host-neg-bit-rate",
+				   &host_neg_bit_rate);
+	if (ret || host_neg_bit_rate > NPCM_PECI_HOST_NEG_BIT_RATE_MAX ||
+	    host_neg_bit_rate < NPCM_PECI_HOST_NEG_BIT_RATE_MIN) {
+		if (ret)
+			dev_warn(priv->dev,
+				 "host-neg-bit-rate not found, use default : %u\n",
+				 NPCM_PECI_HOST_NEG_BIT_RATE_DEFAULT);
+		else
+			dev_warn(priv->dev,
+				 "Invalid host-neg-bit-rate : %u. Use default : %u\n",
+				 host_neg_bit_rate,
+				 NPCM_PECI_HOST_NEG_BIT_RATE_DEFAULT);
+		host_neg_bit_rate = NPCM_PECI_HOST_NEG_BIT_RATE_DEFAULT;
+	}
+
+	regmap_update_bits(priv->regmap, NPCM_PECI_PDDR, NPCM_PECI_PDDR_MASK,
+			   host_neg_bit_rate);
+
+	priv->host_bit_rate = clk_get_rate(priv->clk) /
+		(4 * (host_neg_bit_rate + 1));
+
+	ret = regmap_read_poll_timeout(priv->regmap, NPCM_PECI_CTL_STS, cmd_sts,
+				       !(cmd_sts & NPCM_PECI_CTRL_START_BUSY),
+				       NPCM_PECI_IDLE_CHECK_INTERVAL_USEC,
+				       NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC);
+	if (ret)
+		return ret; /* -ETIMEDOUT */
+
+	/* PECI interrupt enable */
+	regmap_update_bits(priv->regmap, NPCM_PECI_CTL_STS,
+			   NPCM_PECI_CTRL_DONE_INT_EN,
+			   NPCM_PECI_CTRL_DONE_INT_EN);
+
+	return 0;
+}
+
+static const struct regmap_config npcm_peci_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = NPCM_PECI_MAX_REG,
+	.fast_io = true,
+};
+
+static int npcm_peci_xfer(struct peci_adapter *adapter,
+			  struct peci_xfer_msg *msg)
+{
+	struct npcm_peci *priv = peci_get_adapdata(adapter);
+
+	return npcm_peci_xfer_native(priv, msg);
+}
+
+static int npcm_peci_probe(struct platform_device *pdev)
+{
+	struct peci_adapter *adapter;
+	struct npcm_peci *priv;
+	struct resource *res;
+	void __iomem *base;
+	int ret;
+
+	adapter = peci_alloc_adapter(&pdev->dev, sizeof(*priv));
+	if (!adapter)
+		return -ENOMEM;
+
+	priv = peci_get_adapdata(adapter);
+	priv->adapter = adapter;
+	priv->dev = &pdev->dev;
+	dev_set_drvdata(&pdev->dev, priv);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(base)) {
+		ret = PTR_ERR(base);
+		goto err_put_adapter_dev;
+	}
+
+	priv->regmap = devm_regmap_init_mmio(&pdev->dev, base,
+					     &npcm_peci_regmap_config);
+	if (IS_ERR(priv->regmap)) {
+		ret = PTR_ERR(priv->regmap);
+		goto err_put_adapter_dev;
+	}
+
+	priv->irq = platform_get_irq(pdev, 0);
+	if (!priv->irq) {
+		ret = -ENODEV;
+		goto err_put_adapter_dev;
+	}
+
+	ret = devm_request_irq(&pdev->dev, priv->irq, npcm_peci_irq_handler,
+			       0, "peci-npcm-irq", priv);
+	if (ret)
+		goto err_put_adapter_dev;
+
+	init_completion(&priv->xfer_complete);
+	spin_lock_init(&priv->lock);
+
+	priv->adapter->owner = THIS_MODULE;
+	priv->adapter->dev.of_node = of_node_get(dev_of_node(priv->dev));
+	strlcpy(priv->adapter->name, pdev->name, sizeof(priv->adapter->name));
+	priv->adapter->xfer = npcm_peci_xfer;
+
+	ret = npcm_peci_init_ctrl(priv);
+	if (ret)
+		goto err_put_adapter_dev;
+
+	ret = peci_add_adapter(priv->adapter);
+	if (ret)
+		goto err_put_adapter_dev;
+
+	dev_info(&pdev->dev, "peci bus %d registered, host negotiation bit rate %dHz",
+		 priv->adapter->nr, priv->host_bit_rate);
+
+	return 0;
+
+err_put_adapter_dev:
+	put_device(&adapter->dev);
+	return ret;
+}
+
+static int npcm_peci_remove(struct platform_device *pdev)
+{
+	struct npcm_peci *priv = dev_get_drvdata(&pdev->dev);
+
+	clk_disable_unprepare(priv->clk);
+	peci_del_adapter(priv->adapter);
+	of_node_put(priv->adapter->dev.of_node);
+
+	return 0;
+}
+
+static const struct of_device_id npcm_peci_of_table[] = {
+	{ .compatible = "nuvoton,npcm750-peci", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, npcm_peci_of_table);
+
+static struct platform_driver npcm_peci_driver = {
+	.probe  = npcm_peci_probe,
+	.remove = npcm_peci_remove,
+	.driver = {
+		.name           = "peci-npcm",
+		.of_match_table = of_match_ptr(npcm_peci_of_table),
+	},
+};
+module_platform_driver(npcm_peci_driver);
+
+MODULE_AUTHOR("Tomer Maimon <tomer.maimon@nuvoton.com>");
+MODULE_DESCRIPTION("NPCM Platform Environment Control Interface (PECI) driver");
+MODULE_LICENSE("GPL v2");
-- 
2.14.1

[linux dev-5.0 v1 3/4] dts: npcm7xx: add PECI support to NPCM7xx device tree

[Tomer Maimon]

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi | 10 ++++++++++
 arch/arm/boot/dts/nuvoton-npcm750-evb.dts     | 12 ++++++++++++
 2 files changed, 22 insertions(+)

diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
index a24a06170660..04e842f460a9 100644
--- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
+++ b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
@@ -341,6 +341,16 @@
 				};
 			};
 
+			peci: peci-bus@100000 {
+				compatible = "nuvoton,npcm750-peci";
+				reg = <0x100000 0x200>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM7XX_CLK_APB3>;
+				status = "disabled";
+			};
+
 			spi0: spi@200000 {
 				compatible = "nuvoton,npcm750-pspi";
 				reg = <0x200000 0x1000>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
index d951ac997872..7728f7b69d13 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
+++ b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
@@ -492,6 +492,18 @@
 				};
 			};
 
+			peci: peci-bus@100000 {
+				cmd-timeout-ms = <1000>;
+				pull-down = <0>;
+				host-neg-bit-rate = <15>;
+				status = "okay";
+				intel-peci-dimmtemp@30 {
+					compatible = "intel,peci-client";
+					reg = <0x30>;
+					status = "okay";
+				};
+			};
+
 			spi0: spi@200000 {
 				cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
 				status = "okay";
-- 
2.14.1

[linux dev-5.0 v1 4/4] config: npcm7xx: add PECI support to npcm7xx defconfig

[Tomer Maimon]

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 arch/arm/configs/npcm7xx_defconfig | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/configs/npcm7xx_defconfig b/arch/arm/configs/npcm7xx_defconfig
index afddb4e88300..62aaffdba4dd 100644
--- a/arch/arm/configs/npcm7xx_defconfig
+++ b/arch/arm/configs/npcm7xx_defconfig
@@ -120,3 +120,8 @@ CONFIG_CRYPTO_LZO=y
 CONFIG_CRYPTO_USER_API_SKCIPHER=y
 CONFIG_CRYPTO_DEV_NPCMX50=y
 CONFIG_ARM_CRYPTO=y
+CONFIG_PECI=y
+CONFIG_PECI_NPCM=y
+CONFIG_MFD_INTEL_PECI_CLIENT=y
+CONFIG_SENSORS_PECI_CPUTEMP=y
+CONFIG_SENSORS_PECI_DIMMTEMP=y
-- 
2.14.1