All of lore.kernel.org
 help / color / mirror / Atom feed
From: Sudeep Holla <sudeep.holla@arm.com>
To: Prasad Sodagudi <psodagud@codeaurora.org>
Cc: mark.rutland@arm.com, lorenzo.pieralisi@arm.com,
	julien.thierry@arm.com, catalin.marinas@arm.com,
	will.deacon@arm.com, linux-kernel@vger.kernel.org,
	Sudeep Holla <sudeep.holla@arm.com>,
	akpm@linux-foundation.org, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] kernel/panic: Use SYSTEM_RESET2 command for warm reset
Date: Thu, 9 May 2019 10:40:44 +0100	[thread overview]
Message-ID: <20190509094021.GA8239@e107155-lin> (raw)
In-Reply-To: <1557366432-352469-1-git-send-email-psodagud@codeaurora.org>

On Wed, May 08, 2019 at 06:47:12PM -0700, Prasad Sodagudi wrote:
> Some platforms may need warm reboot support when kernel crashed
> for post mortem analysis instead of cold reboot. So use config
> CONFIG_WARM_REBOOT_ON_PANIC and SYSTEM_RESET2 psci command
> support for warm reset.
>

Please drop all the references to PSCI and SYSTEM_RESET2 including
in subject. This is more generic and PSCIv1.1 with SYSTEM_RESET2 can
make use of it.

> Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
> ---
>  kernel/panic.c    |  4 ++++
>  lib/Kconfig.debug | 10 ++++++++++
>  2 files changed, 14 insertions(+)
> 
> diff --git a/kernel/panic.c b/kernel/panic.c
> index c1fcaad..6ab6675 100644
> --- a/kernel/panic.c
> +++ b/kernel/panic.c
> @@ -198,6 +198,10 @@ void panic(const char *fmt, ...)
>  
>  	console_verbose();
>  	bust_spinlocks(1);
> +#ifdef CONFIG_WARM_REBOOT_ON_PANIC
> +	/* Configure for warm reboot instead of cold reboot. */
> +	reboot_mode = REBOOT_WARM;
> +#endif
>  	va_start(args, fmt);
>  	len = vscnprintf(buf, sizeof(buf), fmt, args);
>  	va_end(args);
> diff --git a/lib/Kconfig.debug b/lib/Kconfig.debug
> index d695ec1..2a727d8 100644
> --- a/lib/Kconfig.debug
> +++ b/lib/Kconfig.debug
> @@ -1000,6 +1000,16 @@ config PANIC_TIMEOUT
>  	  value n > 0 will wait n seconds before rebooting, while a timeout
>  	  value n < 0 will reboot immediately.
>  
> +config WARM_REBOOT_ON_PANIC
> +	bool "Warm reboot instead of cold reboot for panic"
> +	default n
> +	help
> +	  Some vendor platform may need warm reboot instead of cold reboot
> +	  for debugging. Before vendor specific power off driver is
> +	  probed, platform always gets cold reset. By setting Y here and
> +	  support for PSCI V1.1 is present from firmware, platform would
> +	  get warm reset instead of cold reset.
> +

Ditto here, drop PSCI reference. Since it's being pushed as generic
solution, expecting anyone reading this to understand what is this PSCI
makes no sense and may be even confusing.

--
Regards,
Sudeep


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

WARNING: multiple messages have this Message-ID (diff)
From: Sudeep Holla <sudeep.holla@arm.com>
To: Prasad Sodagudi <psodagud@codeaurora.org>
Cc: julien.thierry@arm.com, will.deacon@arm.com,
	catalin.marinas@arm.com, mark.rutland@arm.com,
	lorenzo.pieralisi@arm.com, akpm@linux-foundation.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, Sudeep Holla <sudeep.holla@arm.com>
Subject: Re: [PATCH] kernel/panic: Use SYSTEM_RESET2 command for warm reset
Date: Thu, 9 May 2019 10:40:44 +0100	[thread overview]
Message-ID: <20190509094021.GA8239@e107155-lin> (raw)
In-Reply-To: <1557366432-352469-1-git-send-email-psodagud@codeaurora.org>

On Wed, May 08, 2019 at 06:47:12PM -0700, Prasad Sodagudi wrote:
> Some platforms may need warm reboot support when kernel crashed
> for post mortem analysis instead of cold reboot. So use config
> CONFIG_WARM_REBOOT_ON_PANIC and SYSTEM_RESET2 psci command
> support for warm reset.
>

Please drop all the references to PSCI and SYSTEM_RESET2 including
in subject. This is more generic and PSCIv1.1 with SYSTEM_RESET2 can
make use of it.

> Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
> ---
>  kernel/panic.c    |  4 ++++
>  lib/Kconfig.debug | 10 ++++++++++
>  2 files changed, 14 insertions(+)
> 
> diff --git a/kernel/panic.c b/kernel/panic.c
> index c1fcaad..6ab6675 100644
> --- a/kernel/panic.c
> +++ b/kernel/panic.c
> @@ -198,6 +198,10 @@ void panic(const char *fmt, ...)
>  
>  	console_verbose();
>  	bust_spinlocks(1);
> +#ifdef CONFIG_WARM_REBOOT_ON_PANIC
> +	/* Configure for warm reboot instead of cold reboot. */
> +	reboot_mode = REBOOT_WARM;
> +#endif
>  	va_start(args, fmt);
>  	len = vscnprintf(buf, sizeof(buf), fmt, args);
>  	va_end(args);
> diff --git a/lib/Kconfig.debug b/lib/Kconfig.debug
> index d695ec1..2a727d8 100644
> --- a/lib/Kconfig.debug
> +++ b/lib/Kconfig.debug
> @@ -1000,6 +1000,16 @@ config PANIC_TIMEOUT
>  	  value n > 0 will wait n seconds before rebooting, while a timeout
>  	  value n < 0 will reboot immediately.
>  
> +config WARM_REBOOT_ON_PANIC
> +	bool "Warm reboot instead of cold reboot for panic"
> +	default n
> +	help
> +	  Some vendor platform may need warm reboot instead of cold reboot
> +	  for debugging. Before vendor specific power off driver is
> +	  probed, platform always gets cold reset. By setting Y here and
> +	  support for PSCI V1.1 is present from firmware, platform would
> +	  get warm reset instead of cold reset.
> +

Ditto here, drop PSCI reference. Since it's being pushed as generic
solution, expecting anyone reading this to understand what is this PSCI
makes no sense and may be even confusing.

--
Regards,
Sudeep


  reply	other threads:[~2019-05-09  9:41 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-04-30 21:44 PSCI version 1.1 and SYSTEM_RESET2 Sodagudi Prasad
2019-04-30 21:44 ` Sodagudi Prasad
2019-05-01  0:07 ` Sodagudi Prasad
2019-05-01  0:07   ` Sodagudi Prasad
2019-05-01  9:49   ` Sudeep Holla
2019-05-01  9:49     ` Sudeep Holla
2019-05-01 18:43     ` Sodagudi Prasad
2019-05-01 18:43       ` Sodagudi Prasad
2019-05-02  9:05       ` Sudeep Holla
2019-05-02  9:05         ` Sudeep Holla
2019-05-09  1:38         ` Sodagudi Prasad
2019-05-09  1:38           ` Sodagudi Prasad
2019-05-09  1:47           ` [PATCH] kernel/panic: Use SYSTEM_RESET2 command for warm reset Prasad Sodagudi
2019-05-09  1:47             ` Prasad Sodagudi
2019-05-09  9:40             ` Sudeep Holla [this message]
2019-05-09  9:40               ` Sudeep Holla
2019-05-16 18:29             ` Aaro Koskinen
2019-05-16 18:29               ` Aaro Koskinen
2019-05-17 18:03               ` Sodagudi Prasad
2019-05-17 18:03                 ` Sodagudi Prasad

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190509094021.GA8239@e107155-lin \
    --to=sudeep.holla@arm.com \
    --cc=akpm@linux-foundation.org \
    --cc=catalin.marinas@arm.com \
    --cc=julien.thierry@arm.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=lorenzo.pieralisi@arm.com \
    --cc=mark.rutland@arm.com \
    --cc=psodagud@codeaurora.org \
    --cc=will.deacon@arm.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.