All of lore.kernel.org
 help / color / mirror / Atom feed
From: Fabio Estevam <festevam@gmail.com>
To: shawnguo@kernel.org
Cc: linux-arm-kernel@lists.infradead.org,
	Fabio Estevam <festevam@gmail.com>,
	linux-imx@nxp.com, kernel@pengutronix.de, slongerbeam@gmail.com
Subject: [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support
Date: Mon, 20 May 2019 10:24:11 -0300	[thread overview]
Message-ID: <20190520132411.8540-2-festevam@gmail.com> (raw)
In-Reply-To: <20190520132411.8540-1-festevam@gmail.com>

From: Steve Longerbeam <slongerbeam@gmail.com>

Add video capture support from the OV5642 to IPU CSI0 on
the i.MX53 SMD.

Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
[fabio: remove unnecessary 'regulator-always-on' from camera regulators]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
---
 arch/arm/boot/dts/imx53-smd.dts | 73 +++++++++++++++++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts
index 09071ca11c6c..ffdc6d990795 100644
--- a/arch/arm/boot/dts/imx53-smd.dts
+++ b/arch/arm/boot/dts/imx53-smd.dts
@@ -185,6 +185,31 @@
 			>;
 		};
 
+		pinctrl_ipu_csi0: ipucsi0grp {
+			fsl,pins = <
+				MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12    0x1c4
+				MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13    0x1c4
+				MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14    0x1c4
+				MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15    0x1c4
+				MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16    0x1c4
+				MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17    0x1c4
+				MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18    0x1c4
+				MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19    0x1c4
+				MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK 0x1e4
+				MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC   0x1e4
+				MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC    0x1e4
+				MX53_PAD_CSI0_DATA_EN__IPU_CSI0_DATA_EN 0x1e4
+			>;
+		};
+
+		pinctrl_ov5642: ov5642grp {
+			fsl,pins = <
+				MX53_PAD_NANDF_WP_B__GPIO6_9   0x1e4
+				MX53_PAD_NANDF_RB0__GPIO6_10   0x1e4
+				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x1c4
+			>;
+		};
+
 		pinctrl_uart1: uart1grp {
 			fsl,pins = <
 				MX53_PAD_CSI0_DAT10__UART1_TXD_MUX	0x1e4
@@ -256,11 +281,47 @@
 	camera: ov5642@3c {
 		compatible = "ovti,ov5642";
 		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5642>;
+		assigned-clocks = <&clks IMX5_CLK_SSI_EXT1_SEL>,
+				  <&clks IMX5_CLK_SSI_EXT1_COM_SEL>;
+		assigned-clock-parents = <&clks IMX5_CLK_PLL2_SW>,
+					 <&clks IMX5_CLK_SSI_EXT1_PODF>;
+		assigned-clock-rates = <0>, <24000000>;
+		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
+		clock-names = "xclk";
+		DVDD-supply = <&ldo9_reg>;
+		AVDD-supply = <&ldo7_reg>;
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+
+		port {
+			ov5642_to_ipu_csi0: endpoint {
+				remote-endpoint = <&ipu_csi0_from_parallel_sensor>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
 	};
 
 	pmic: dialog@48 {
 		compatible = "dlg,da9053", "dlg,da9052";
 		reg = <0x48>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			ldo7_reg: ldo7 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+			};
+
+			ldo9_reg: ldo9 {
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <3650000>;
+			};
+		};
 	};
 };
 
@@ -271,3 +332,15 @@
 	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
+
+&ipu_csi0_from_parallel_sensor {
+	remote-endpoint = <&ov5642_to_ipu_csi0>;
+	data-shift = <12>; /* Lines 19:12 used */
+	hsync-active = <1>;
+	vsync-active = <1>;
+};
+
+&ipu_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu_csi0>;
+};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2019-05-20 13:24 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-20 13:24 [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Fabio Estevam
2019-05-20 13:24 ` Fabio Estevam [this message]
2019-05-23  9:06 ` Shawn Guo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190520132411.8540-2-festevam@gmail.com \
    --to=festevam@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=shawnguo@kernel.org \
    --cc=slongerbeam@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.