* [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device
@ 2019-05-20 13:24 Fabio Estevam
2019-05-20 13:24 ` [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support Fabio Estevam
2019-05-23 9:06 ` [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Shawn Guo
0 siblings, 2 replies; 3+ messages in thread
From: Fabio Estevam @ 2019-05-20 13:24 UTC (permalink / raw)
To: shawnguo; +Cc: linux-arm-kernel, Fabio Estevam, linux-imx, kernel, slongerbeam
From: Steve Longerbeam <slongerbeam@gmail.com>
Add video capture_subsystem device node, and include both CSI ports.
Prepare for adding sensors by adding the parallel sensor anchor endpoints
to the CSI ports.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
---
arch/arm/boot/dts/imx53.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi
index 9b672ed2486d..ed341cfd9d09 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/imx53.dtsi
@@ -31,6 +31,7 @@
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
+ ipu0 = &ipu;
mmc0 = &esdhc1;
mmc1 = &esdhc2;
mmc2 = &esdhc3;
@@ -71,6 +72,11 @@
ports = <&ipu_di0>, <&ipu_di1>;
};
+ capture_subsystem {
+ compatible = "fsl,imx-capture-subsystem";
+ ports = <&ipu_csi0>, <&ipu_csi1>;
+ };
+
tzic: tz-interrupt-controller@fffc000 {
compatible = "fsl,imx53-tzic", "fsl,tzic";
interrupt-controller;
@@ -158,10 +164,16 @@
ipu_csi0: port@0 {
reg = <0>;
+
+ ipu_csi0_from_parallel_sensor: endpoint {
+ };
};
ipu_csi1: port@1 {
reg = <1>;
+
+ ipu_csi1_from_parallel_sensor: endpoint {
+ };
};
ipu_di0: port@2 {
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 3+ messages in thread* [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support
2019-05-20 13:24 [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Fabio Estevam
@ 2019-05-20 13:24 ` Fabio Estevam
2019-05-23 9:06 ` [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Fabio Estevam @ 2019-05-20 13:24 UTC (permalink / raw)
To: shawnguo; +Cc: linux-arm-kernel, Fabio Estevam, linux-imx, kernel, slongerbeam
From: Steve Longerbeam <slongerbeam@gmail.com>
Add video capture support from the OV5642 to IPU CSI0 on
the i.MX53 SMD.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
[fabio: remove unnecessary 'regulator-always-on' from camera regulators]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
---
arch/arm/boot/dts/imx53-smd.dts | 73 +++++++++++++++++++++++++++++++++
1 file changed, 73 insertions(+)
diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts
index 09071ca11c6c..ffdc6d990795 100644
--- a/arch/arm/boot/dts/imx53-smd.dts
+++ b/arch/arm/boot/dts/imx53-smd.dts
@@ -185,6 +185,31 @@
>;
};
+ pinctrl_ipu_csi0: ipucsi0grp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12 0x1c4
+ MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13 0x1c4
+ MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14 0x1c4
+ MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15 0x1c4
+ MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16 0x1c4
+ MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17 0x1c4
+ MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18 0x1c4
+ MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19 0x1c4
+ MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK 0x1e4
+ MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC 0x1e4
+ MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC 0x1e4
+ MX53_PAD_CSI0_DATA_EN__IPU_CSI0_DATA_EN 0x1e4
+ >;
+ };
+
+ pinctrl_ov5642: ov5642grp {
+ fsl,pins = <
+ MX53_PAD_NANDF_WP_B__GPIO6_9 0x1e4
+ MX53_PAD_NANDF_RB0__GPIO6_10 0x1e4
+ MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x1c4
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4
@@ -256,11 +281,47 @@
camera: ov5642@3c {
compatible = "ovti,ov5642";
reg = <0x3c>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5642>;
+ assigned-clocks = <&clks IMX5_CLK_SSI_EXT1_SEL>,
+ <&clks IMX5_CLK_SSI_EXT1_COM_SEL>;
+ assigned-clock-parents = <&clks IMX5_CLK_PLL2_SW>,
+ <&clks IMX5_CLK_SSI_EXT1_PODF>;
+ assigned-clock-rates = <0>, <24000000>;
+ clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
+ clock-names = "xclk";
+ DVDD-supply = <&ldo9_reg>;
+ AVDD-supply = <&ldo7_reg>;
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+
+ port {
+ ov5642_to_ipu_csi0: endpoint {
+ remote-endpoint = <&ipu_csi0_from_parallel_sensor>;
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
};
pmic: dialog@48 {
compatible = "dlg,da9053", "dlg,da9052";
reg = <0x48>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ ldo7_reg: ldo7 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ ldo9_reg: ldo9 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <3650000>;
+ };
+ };
};
};
@@ -271,3 +332,15 @@
phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
+
+&ipu_csi0_from_parallel_sensor {
+ remote-endpoint = <&ov5642_to_ipu_csi0>;
+ data-shift = <12>; /* Lines 19:12 used */
+ hsync-active = <1>;
+ vsync-active = <1>;
+};
+
+&ipu_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_csi0>;
+};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device
2019-05-20 13:24 [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Fabio Estevam
2019-05-20 13:24 ` [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support Fabio Estevam
@ 2019-05-23 9:06 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2019-05-23 9:06 UTC (permalink / raw)
To: Fabio Estevam; +Cc: linux-arm-kernel, linux-imx, kernel, slongerbeam
On Mon, May 20, 2019 at 10:24:10AM -0300, Fabio Estevam wrote:
> From: Steve Longerbeam <slongerbeam@gmail.com>
>
> Add video capture_subsystem device node, and include both CSI ports.
> Prepare for adding sensors by adding the parallel sensor anchor endpoints
> to the CSI ports.
>
> Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
> Signed-off-by: Fabio Estevam <festevam@gmail.com>
Applied both, thanks.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-05-23 9:07 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2019-05-20 13:24 [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Fabio Estevam
2019-05-20 13:24 ` [PATCH RESEND 2/2] ARM: dts: imx53-smd: Add OV5642 video capture support Fabio Estevam
2019-05-23 9:06 ` [PATCH RESEND 1/2] ARM: dts: imx53: Add capture-subsystem device Shawn Guo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.