From: Shawn Guo <shawnguo@kernel.org>
To: Kuldeep Singh <kuldeep.singh@nxp.com>
Cc: "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"bbrezillon@kernel.org" <bbrezillon@kernel.org>,
Ashish Kumar <ashish.kumar@nxp.com>,
"broonie@kernel.org" <broonie@kernel.org>,
"linux-mtd@lists.infradead.org" <linux-mtd@lists.infradead.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH] arm64: dts: ls1012a: Add QSPI support for ls1012a
Date: Thu, 23 May 2019 16:43:42 +0800 [thread overview]
Message-ID: <20190523084340.GM9261@dragon> (raw)
In-Reply-To: <20190516114807.30817-1-kuldeep.singh@nxp.com>
On Thu, May 16, 2019 at 11:47:04AM +0000, Kuldeep Singh wrote:
> QSPI support is added for kernel version greater than 5.0 and supports
> quad mode defined by
> TX-WIDTH = <4>, RX-WIDTH = <4>
>
> RDB/QDS has one 64MB flash from SPANSION(s25fs512s)
>
> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> ---
> Dependency on https://patchwork.ozlabs.org/patch/1100471/
> Dependency on https://patchwork.ozlabs.org/patch/1100472/
>
> .../arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts | 15 +++++++++++++++
> .../arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 15 +++++++++++++++
> 5 files changed, 75 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> index f90c040fd5e8..8826278b37bf 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> @@ -61,6 +61,21 @@
> status = "okay";
> };
>
> +&qspi {
Please sort these labeling nodes alphabetically. That said, &qspi
should go after &i2c0.
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &i2c0 {
> status = "okay";
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> index 8749634c55ee..0246e8c97628 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> @@ -20,6 +20,21 @@
> status = "okay";
> };
>
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &i2c0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> index 2fb1cb1f7d8f..c304fa20c1c9 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> @@ -90,6 +90,21 @@
> };
> };
>
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &duart0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> index 5edb1e137a52..6017e9cfe40a 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> @@ -38,3 +38,18 @@
> &sata {
> status = "okay";
> };
> +
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> index ec6257a5b251..268268c6a149 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> @@ -350,6 +350,21 @@
> status = "disabled";
> };
>
> + qspi: spi@1550000 {
Please sort node with unit-address in that address. That said, it
should go before esdhc@1560000.
> + compatible = "fsl,ls1021a-qspi", "fsl,ls1012a-qspi";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x1550000 0x0 0x10000>,
> + <0x0 0x40000000 0x0 0x10000000>;
> + reg-names = "QuadSPI", "QuadSPI-memory";
> + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "qspi_en", "qspi";
> + clocks = <&clockgen 4 1>, <&clockgen 4 1>;
> + big-endian;
> + fsl,qspi-has-second-chip;
Undocumented property?
Shawn
> + status = "disabled";
> + };
> +
> duart0: serial@21c0500 {
> compatible = "fsl,ns16550", "ns16550a";
> reg = <0x00 0x21c0500 0x0 0x100>;
> --
> 2.17.1
>
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
WARNING: multiple messages have this Message-ID (diff)
From: Shawn Guo <shawnguo@kernel.org>
To: Kuldeep Singh <kuldeep.singh@nxp.com>
Cc: "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"bbrezillon@kernel.org" <bbrezillon@kernel.org>,
Ashish Kumar <ashish.kumar@nxp.com>,
"broonie@kernel.org" <broonie@kernel.org>,
"linux-mtd@lists.infradead.org" <linux-mtd@lists.infradead.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH] arm64: dts: ls1012a: Add QSPI support for ls1012a
Date: Thu, 23 May 2019 16:43:42 +0800 [thread overview]
Message-ID: <20190523084340.GM9261@dragon> (raw)
In-Reply-To: <20190516114807.30817-1-kuldeep.singh@nxp.com>
On Thu, May 16, 2019 at 11:47:04AM +0000, Kuldeep Singh wrote:
> QSPI support is added for kernel version greater than 5.0 and supports
> quad mode defined by
> TX-WIDTH = <4>, RX-WIDTH = <4>
>
> RDB/QDS has one 64MB flash from SPANSION(s25fs512s)
>
> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> ---
> Dependency on https://patchwork.ozlabs.org/patch/1100471/
> Dependency on https://patchwork.ozlabs.org/patch/1100472/
>
> .../arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts | 15 +++++++++++++++
> .../arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 15 +++++++++++++++
> 5 files changed, 75 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> index f90c040fd5e8..8826278b37bf 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> @@ -61,6 +61,21 @@
> status = "okay";
> };
>
> +&qspi {
Please sort these labeling nodes alphabetically. That said, &qspi
should go after &i2c0.
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &i2c0 {
> status = "okay";
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> index 8749634c55ee..0246e8c97628 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> @@ -20,6 +20,21 @@
> status = "okay";
> };
>
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &i2c0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> index 2fb1cb1f7d8f..c304fa20c1c9 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> @@ -90,6 +90,21 @@
> };
> };
>
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &duart0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> index 5edb1e137a52..6017e9cfe40a 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> @@ -38,3 +38,18 @@
> &sata {
> status = "okay";
> };
> +
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> index ec6257a5b251..268268c6a149 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> @@ -350,6 +350,21 @@
> status = "disabled";
> };
>
> + qspi: spi@1550000 {
Please sort node with unit-address in that address. That said, it
should go before esdhc@1560000.
> + compatible = "fsl,ls1021a-qspi", "fsl,ls1012a-qspi";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x1550000 0x0 0x10000>,
> + <0x0 0x40000000 0x0 0x10000000>;
> + reg-names = "QuadSPI", "QuadSPI-memory";
> + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "qspi_en", "qspi";
> + clocks = <&clockgen 4 1>, <&clockgen 4 1>;
> + big-endian;
> + fsl,qspi-has-second-chip;
Undocumented property?
Shawn
> + status = "disabled";
> + };
> +
> duart0: serial@21c0500 {
> compatible = "fsl,ns16550", "ns16550a";
> reg = <0x00 0x21c0500 0x0 0x100>;
> --
> 2.17.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Shawn Guo <shawnguo@kernel.org>
To: Kuldeep Singh <kuldeep.singh@nxp.com>
Cc: "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"bbrezillon@kernel.org" <bbrezillon@kernel.org>,
Ashish Kumar <ashish.kumar@nxp.com>,
"broonie@kernel.org" <broonie@kernel.org>,
"linux-mtd@lists.infradead.org" <linux-mtd@lists.infradead.org>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH] arm64: dts: ls1012a: Add QSPI support for ls1012a
Date: Thu, 23 May 2019 16:43:42 +0800 [thread overview]
Message-ID: <20190523084340.GM9261@dragon> (raw)
In-Reply-To: <20190516114807.30817-1-kuldeep.singh@nxp.com>
On Thu, May 16, 2019 at 11:47:04AM +0000, Kuldeep Singh wrote:
> QSPI support is added for kernel version greater than 5.0 and supports
> quad mode defined by
> TX-WIDTH = <4>, RX-WIDTH = <4>
>
> RDB/QDS has one 64MB flash from SPANSION(s25fs512s)
>
> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> ---
> Dependency on https://patchwork.ozlabs.org/patch/1100471/
> Dependency on https://patchwork.ozlabs.org/patch/1100472/
>
> .../arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts | 15 +++++++++++++++
> .../arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts | 15 +++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 15 +++++++++++++++
> 5 files changed, 75 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> index f90c040fd5e8..8826278b37bf 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts
> @@ -61,6 +61,21 @@
> status = "okay";
> };
>
> +&qspi {
Please sort these labeling nodes alphabetically. That said, &qspi
should go after &i2c0.
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &i2c0 {
> status = "okay";
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> index 8749634c55ee..0246e8c97628 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frwy.dts
> @@ -20,6 +20,21 @@
> status = "okay";
> };
>
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &i2c0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> index 2fb1cb1f7d8f..c304fa20c1c9 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> @@ -90,6 +90,21 @@
> };
> };
>
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> +
> &duart0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> index 5edb1e137a52..6017e9cfe40a 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> @@ -38,3 +38,18 @@
> &sata {
> status = "okay";
> };
> +
> +&qspi {
> + status = "okay";
> +
> + qflash0: flash@0 {
> + compatible = "spansion,m25p80", "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + m25p,fast-read;
> + spi-max-frequency = <20000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <4>;
> + reg = <0>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> index ec6257a5b251..268268c6a149 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> @@ -350,6 +350,21 @@
> status = "disabled";
> };
>
> + qspi: spi@1550000 {
Please sort node with unit-address in that address. That said, it
should go before esdhc@1560000.
> + compatible = "fsl,ls1021a-qspi", "fsl,ls1012a-qspi";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x0 0x1550000 0x0 0x10000>,
> + <0x0 0x40000000 0x0 0x10000000>;
> + reg-names = "QuadSPI", "QuadSPI-memory";
> + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> + clock-names = "qspi_en", "qspi";
> + clocks = <&clockgen 4 1>, <&clockgen 4 1>;
> + big-endian;
> + fsl,qspi-has-second-chip;
Undocumented property?
Shawn
> + status = "disabled";
> + };
> +
> duart0: serial@21c0500 {
> compatible = "fsl,ns16550", "ns16550a";
> reg = <0x00 0x21c0500 0x0 0x100>;
> --
> 2.17.1
>
next prev parent reply other threads:[~2019-05-23 8:44 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-16 11:47 [PATCH] arm64: dts: ls1012a: Add QSPI support for ls1012a Kuldeep Singh
2019-05-16 11:47 ` Kuldeep Singh
2019-05-16 11:47 ` Kuldeep Singh
2019-05-16 11:47 ` [PATCH] arm64: dts: ls1046a: Fast read m25p60 Kuldeep Singh
2019-05-16 11:47 ` Kuldeep Singh
2019-05-16 11:47 ` Kuldeep Singh
2019-05-23 8:47 ` Shawn Guo
2019-05-23 8:47 ` Shawn Guo
2019-05-23 8:47 ` Shawn Guo
2019-05-16 11:47 ` [PATCH] arm64: dts: ls1088a: Add QSPI support Kuldeep Singh
2019-05-16 11:47 ` Kuldeep Singh
2019-05-23 8:48 ` Shawn Guo
2019-05-23 8:48 ` Shawn Guo
2019-05-23 8:48 ` Shawn Guo
2019-05-16 11:47 ` [PATCH] arm64: dts: ls208x: Remove non-compatible driver device from qspi node Kuldeep Singh
2019-05-16 11:47 ` Kuldeep Singh
2019-05-23 8:43 ` Shawn Guo [this message]
2019-05-23 8:43 ` [PATCH] arm64: dts: ls1012a: Add QSPI support for ls1012a Shawn Guo
2019-05-23 8:43 ` Shawn Guo
2019-05-23 9:01 ` Schrempf Frieder
2019-05-23 9:01 ` Schrempf Frieder
2019-05-23 9:01 ` Schrempf Frieder
2019-05-23 9:19 ` [EXT] " Kuldeep Singh
2019-05-23 9:19 ` Kuldeep Singh
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190523084340.GM9261@dragon \
--to=shawnguo@kernel.org \
--cc=ashish.kumar@nxp.com \
--cc=bbrezillon@kernel.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kuldeep.singh@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-mtd@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.