Re: [PATCH v2 3/3] arm64: dts: freescale: Add support for i.MX8QXP AI_ML board

[Shawn Guo <shawnguo@kernel.org>]

On Fri, Jul 19, 2019 at 12:39:26PM +0530, Manivannan Sadhasivam wrote:
> Add support for i.MX8QXP AI_ML board from Einfochips. This board is one
> of the Consumer Edition boards of the 96Boards family based on i.MX8QXP
> SoC from NXP/Freescale.
> 
> The initial support includes following peripherals which are tested and
> known to be working:
> 
> 1. Debug serial via UART2
> 2. uSD
> 3. WiFi
> 4. Ethernet
> 
> More information about this board can be found in Arrow website:
> https://www.arrow.com/en/products/imx8-ai-ml/arrow-development-tools
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
> ---
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../boot/dts/freescale/imx8qxp-ai_ml.dts      | 249 ++++++++++++++++++
>  2 files changed, 250 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 0bd122f60549..bd8460549d1a 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -24,4 +24,5 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts b/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts
> new file mode 100644
> index 000000000000..3dc8757d9c42
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts
> @@ -0,0 +1,249 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2018 Einfochips
> + * Copyright 2019 Linaro Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8qxp.dtsi"
> +
> +/ {
> +	model = "Einfochips i.MX8QXP AI_ML";
> +	compatible = "einfochips,imx8qxp-ai_ml", "fsl,imx8qxp";
> +
> +	aliases {
> +		serial1 = &adma_lpuart1;
> +		serial2 = &adma_lpuart2;
> +		serial3 = &adma_lpuart3;
> +	};
> +
> +	chosen {
> +		stdout-path = &adma_lpuart2;
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x00000000 0x80000000 0 0x80000000>;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_leds>;
> +
> +		user_led1 {
> +			label = "green:user1";
> +			gpios = <&lsio_gpio4 16 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		user_led2 {
> +			label = "green:user2";
> +			gpios = <&lsio_gpio0 6 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "none";
> +		};
> +
> +		user_led3 {
> +			label = "green:user3";
> +			gpios = <&lsio_gpio0 7 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "mmc1";
> +			default-state = "off";
> +		};
> +
> +		user_led4 {
> +			label = "green:user4";
> +			gpios = <&lsio_gpio4 21 GPIO_ACTIVE_HIGH>;
> +			panic-indicator;
> +			linux,default-trigger = "none";
> +		};
> +
> +		wlan_active_led {
> +			label = "yellow:wlan";
> +			gpios = <&lsio_gpio4 17 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "phy0tx";
> +			default-state = "off";
> +		};
> +
> +		bt_active_led {

We prefer to use hyphen over underscore in node names.  I fixed them up
and applied the series.

Shawn

> +			label = "blue:bt";
> +			gpios = <&lsio_gpio4 18 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "hci0-power";
> +			default-state = "off";
> +		};
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_wifi_reg_on>;
> +		reset-gpios = <&lsio_gpio3 24 GPIO_ACTIVE_LOW>;
> +	};
> +};
> +
> +/* BT */
> +&adma_lpuart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart0>;
> +	uart-has-rtscts;
> +	status = "okay";
> +};
> +
> +/* LS-UART0 */
> +&adma_lpuart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart1>;
> +	status = "okay";
> +};
> +
> +/* Debug */
> +&adma_lpuart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart2>;
> +	status = "okay";
> +};
> +
> +/* PCI-E UART */
> +&adma_lpuart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart3>;
> +	status = "okay";
> +};
> +
> +&fec1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_fec1>;
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&ethphy0>;
> +	fsl,magic-packet;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy0: ethernet-phy@0 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +		};
> +	};
> +};
> +
> +/* WiFi */
> +&usdhc1 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	bus-width = <4>;
> +	no-sd;
> +	non-removable;
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +	status = "okay";
> +
> +	brcmf: wifi@1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +/* SD */
> +&usdhc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc2>;
> +	bus-width = <4>;
> +	cd-gpios = <&lsio_gpio4 22 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl_fec1: fec1grp {
> +		fsl,pins = <
> +			IMX8QXP_ENET0_MDC_CONN_ENET0_MDC			0x06000020
> +			IMX8QXP_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
> +			IMX8QXP_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x06000020
> +			IMX8QXP_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC		0x06000020
> +			IMX8QXP_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0		0x06000020
> +			IMX8QXP_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1		0x06000020
> +			IMX8QXP_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2		0x06000020
> +			IMX8QXP_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3		0x06000020
> +			IMX8QXP_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC		0x06000020
> +			IMX8QXP_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x06000020
> +			IMX8QXP_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0		0x06000020
> +			IMX8QXP_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1		0x06000020
> +			IMX8QXP_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2		0x06000020
> +			IMX8QXP_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3		0x06000020
> +		>;
> +	};
> +
> +	pinctrl_leds: ledsgrp{
> +		fsl,pins = <
> +			IMX8QXP_ESAI0_TX2_RX3_LSIO_GPIO0_IO06			0x00000021
> +			IMX8QXP_ESAI0_TX3_RX2_LSIO_GPIO0_IO07			0x00000021
> +			IMX8QXP_EMMC0_DATA7_LSIO_GPIO4_IO16			0x00000021
> +			IMX8QXP_USDHC1_WP_LSIO_GPIO4_IO21			0x00000021
> +			IMX8QXP_EMMC0_STROBE_LSIO_GPIO4_IO17			0x00000021
> +			IMX8QXP_EMMC0_RESET_B_LSIO_GPIO4_IO18			0x00000021
> +		>;
> +	};
> +
> +	pinctrl_lpuart0: lpuart0grp {
> +		fsl,pins = <
> +			IMX8QXP_UART0_RX_ADMA_UART0_RX				0X06000020
> +			IMX8QXP_UART0_TX_ADMA_UART0_TX				0X06000020
> +			IMX8QXP_FLEXCAN0_TX_ADMA_UART0_CTS_B 			0x06000020
> +			IMX8QXP_FLEXCAN0_RX_ADMA_UART0_RTS_B			0x06000020
> +		>;
> +	};
> +
> +	pinctrl_lpuart1: lpuart1grp {
> +		fsl,pins = <
> +			IMX8QXP_UART1_RX_ADMA_UART1_RX				0X06000020
> +			IMX8QXP_UART1_TX_ADMA_UART1_TX				0X06000020
> +		>;
> +	};
> +
> +	pinctrl_lpuart2: lpuart2grp {
> +		fsl,pins = <
> +			IMX8QXP_UART2_RX_ADMA_UART2_RX				0X06000020
> +			IMX8QXP_UART2_TX_ADMA_UART2_TX				0X06000020
> +		>;
> +	};
> +
> +	pinctrl_lpuart3: lpuart3grp {
> +		fsl,pins = <
> +			IMX8QXP_FLEXCAN2_RX_ADMA_UART3_RX			0X06000020
> +			IMX8QXP_FLEXCAN2_TX_ADMA_UART3_TX			0X06000020
> +		>;
> +	};
> +
> +	pinctrl_usdhc1: usdhc1grp {
> +		fsl,pins = <
> +			IMX8QXP_EMMC0_CLK_CONN_EMMC0_CLK			0x06000041
> +			IMX8QXP_EMMC0_CMD_CONN_EMMC0_CMD			0x00000021
> +			IMX8QXP_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000021
> +			IMX8QXP_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000021
> +			IMX8QXP_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000021
> +			IMX8QXP_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000021
> +		>;
> +	};
> +
> +	pinctrl_usdhc2: usdhc2grp {
> +		fsl,pins = <
> +			IMX8QXP_USDHC1_CLK_CONN_USDHC1_CLK			0x06000041
> +			IMX8QXP_USDHC1_CMD_CONN_USDHC1_CMD			0x00000021
> +			IMX8QXP_USDHC1_DATA0_CONN_USDHC1_DATA0			0x00000021
> +			IMX8QXP_USDHC1_DATA1_CONN_USDHC1_DATA1			0x00000021
> +			IMX8QXP_USDHC1_DATA2_CONN_USDHC1_DATA2			0x00000021
> +			IMX8QXP_USDHC1_DATA3_CONN_USDHC1_DATA3			0x00000021
> +			IMX8QXP_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021
> +			IMX8QXP_USDHC1_CD_B_LSIO_GPIO4_IO22			0x00000021
> +		>;
> +	};
> +
> +	pinctrl_wifi_reg_on: wifiregongrp {
> +		fsl,pins = <
> +			IMX8QXP_QSPI0B_SS1_B_LSIO_GPIO3_IO24			0x00000021
> +		>;
> +	};
> +};
> -- 
> 2.17.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel