* [PATCH 0/3] Add new Overkiz Kizbox3 support @ 2019-10-11 12:50 ` Kamel Bouhara 0 siblings, 0 replies; 18+ messages in thread From: Kamel Bouhara @ 2019-10-11 12:50 UTC (permalink / raw) To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel Cc: devicetree, linux-kernel, Thomas Petazzoni, Kamel Bouhara Add support for the Kizbox3 Overkiz SAS boards. Those boards are based on the Atmel SAMA5D27 SoC. Kamel Bouhara (3): dt-bindings: Add vendor prefix for Overkiz SAS dt-bindings: arm: at91: Document Kizbox3 HS board binding ARM: at91: add Overkiz KIZBOX3 board .../devicetree/bindings/arm/atmel-at91.yaml | 7 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-kizbox3-hs.dts | 309 +++++++++++++ arch/arm/boot/dts/at91-kizbox3_common.dtsi | 412 ++++++++++++++++++ 5 files changed, 731 insertions(+) create mode 100644 arch/arm/boot/dts/at91-kizbox3-hs.dts create mode 100644 arch/arm/boot/dts/at91-kizbox3_common.dtsi -- 2.23.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 0/3] Add new Overkiz Kizbox3 support @ 2019-10-11 12:50 ` Kamel Bouhara 0 siblings, 0 replies; 18+ messages in thread From: Kamel Bouhara @ 2019-10-11 12:50 UTC (permalink / raw) To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel Cc: Thomas Petazzoni, devicetree, linux-kernel, Kamel Bouhara Add support for the Kizbox3 Overkiz SAS boards. Those boards are based on the Atmel SAMA5D27 SoC. Kamel Bouhara (3): dt-bindings: Add vendor prefix for Overkiz SAS dt-bindings: arm: at91: Document Kizbox3 HS board binding ARM: at91: add Overkiz KIZBOX3 board .../devicetree/bindings/arm/atmel-at91.yaml | 7 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-kizbox3-hs.dts | 309 +++++++++++++ arch/arm/boot/dts/at91-kizbox3_common.dtsi | 412 ++++++++++++++++++ 5 files changed, 731 insertions(+) create mode 100644 arch/arm/boot/dts/at91-kizbox3-hs.dts create mode 100644 arch/arm/boot/dts/at91-kizbox3_common.dtsi -- 2.23.0 ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 1/3] dt-bindings: Add vendor prefix for Overkiz SAS 2019-10-11 12:50 ` Kamel Bouhara @ 2019-10-11 12:50 ` Kamel Bouhara -1 siblings, 0 replies; 18+ messages in thread From: Kamel Bouhara @ 2019-10-11 12:50 UTC (permalink / raw) To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel Cc: devicetree, linux-kernel, Thomas Petazzoni, Kamel Bouhara Overkiz is a smarthome solutions provider, more information on: https://www.overkiz.com Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 967e78c5ec0a..9b1582b3bdc3 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -705,6 +705,8 @@ patternProperties: description: Ortus Technology Co., Ltd. "^osddisplays,.*": description: OSD Displays + "^overkiz,.*": + description: Overkiz SAS "^ovti,.*": description: OmniVision Technologies "^oxsemi,.*": -- 2.23.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 1/3] dt-bindings: Add vendor prefix for Overkiz SAS @ 2019-10-11 12:50 ` Kamel Bouhara 0 siblings, 0 replies; 18+ messages in thread From: Kamel Bouhara @ 2019-10-11 12:50 UTC (permalink / raw) To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel Cc: Thomas Petazzoni, devicetree, linux-kernel, Kamel Bouhara Overkiz is a smarthome solutions provider, more information on: https://www.overkiz.com Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 967e78c5ec0a..9b1582b3bdc3 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -705,6 +705,8 @@ patternProperties: description: Ortus Technology Co., Ltd. "^osddisplays,.*": description: OSD Displays + "^overkiz,.*": + description: Overkiz SAS "^ovti,.*": description: OmniVision Technologies "^oxsemi,.*": -- 2.23.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH 1/3] dt-bindings: Add vendor prefix for Overkiz SAS 2019-10-11 12:50 ` Kamel Bouhara @ 2019-10-15 22:46 ` Rob Herring -1 siblings, 0 replies; 18+ messages in thread From: Rob Herring @ 2019-10-15 22:46 UTC (permalink / raw) To: Kamel Bouhara Cc: devicetree, Alexandre Belloni, Kamel Bouhara, linux-kernel, Ludovic Desroches, Thomas Petazzoni, linux-arm-kernel On Fri, 11 Oct 2019 14:50:20 +0200, Kamel Bouhara wrote: > Overkiz is a smarthome solutions provider, more information on: > https://www.overkiz.com > > Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> > --- > Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ > 1 file changed, 2 insertions(+) > Acked-by: Rob Herring <robh@kernel.org> _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 1/3] dt-bindings: Add vendor prefix for Overkiz SAS @ 2019-10-15 22:46 ` Rob Herring 0 siblings, 0 replies; 18+ messages in thread From: Rob Herring @ 2019-10-15 22:46 UTC (permalink / raw) To: Kamel Bouhara Cc: Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel, Thomas Petazzoni, devicetree, linux-kernel, Kamel Bouhara On Fri, 11 Oct 2019 14:50:20 +0200, Kamel Bouhara wrote: > Overkiz is a smarthome solutions provider, more information on: > https://www.overkiz.com > > Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> > --- > Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ > 1 file changed, 2 insertions(+) > Acked-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 2/3] dt-bindings: arm: at91: Document Kizbox3 HS board binding 2019-10-11 12:50 ` Kamel Bouhara @ 2019-10-11 12:50 ` Kamel Bouhara -1 siblings, 0 replies; 18+ messages in thread From: Kamel Bouhara @ 2019-10-11 12:50 UTC (permalink / raw) To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel Cc: devicetree, linux-kernel, Thomas Petazzoni, Kamel Bouhara Document devicetree binding of SAMA5D27 Kizbox3 HS board from Overkiz SAS. Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> --- Documentation/devicetree/bindings/arm/atmel-at91.yaml | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml index 6e168abcd4d1..c0869cb860f3 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml +++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml @@ -45,6 +45,13 @@ properties: - const: atmel,at91sam9x5 - const: atmel,at91sam9 + - description: Overkiz kizbox3 board + items: + - const: overkiz,kizbox3-hs + - const: atmel,sama5d27 + - const: atmel,sama5d2 + - const: atmel,sama5 + - items: - const: atmel,sama5d27 - const: atmel,sama5d2 -- 2.23.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 2/3] dt-bindings: arm: at91: Document Kizbox3 HS board binding @ 2019-10-11 12:50 ` Kamel Bouhara 0 siblings, 0 replies; 18+ messages in thread From: Kamel Bouhara @ 2019-10-11 12:50 UTC (permalink / raw) To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel Cc: Thomas Petazzoni, devicetree, linux-kernel, Kamel Bouhara Document devicetree binding of SAMA5D27 Kizbox3 HS board from Overkiz SAS. Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> --- Documentation/devicetree/bindings/arm/atmel-at91.yaml | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml index 6e168abcd4d1..c0869cb860f3 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml +++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml @@ -45,6 +45,13 @@ properties: - const: atmel,at91sam9x5 - const: atmel,at91sam9 + - description: Overkiz kizbox3 board + items: + - const: overkiz,kizbox3-hs + - const: atmel,sama5d27 + - const: atmel,sama5d2 + - const: atmel,sama5 + - items: - const: atmel,sama5d27 - const: atmel,sama5d2 -- 2.23.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] dt-bindings: arm: at91: Document Kizbox3 HS board binding 2019-10-11 12:50 ` Kamel Bouhara @ 2019-10-15 22:47 ` Rob Herring -1 siblings, 0 replies; 18+ messages in thread From: Rob Herring @ 2019-10-15 22:47 UTC (permalink / raw) To: Kamel Bouhara Cc: devicetree, Alexandre Belloni, Kamel Bouhara, linux-kernel, Ludovic Desroches, Thomas Petazzoni, linux-arm-kernel On Fri, 11 Oct 2019 14:50:21 +0200, Kamel Bouhara wrote: > Document devicetree binding of SAMA5D27 Kizbox3 HS board from Overkiz > SAS. > > Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> > --- > Documentation/devicetree/bindings/arm/atmel-at91.yaml | 7 +++++++ > 1 file changed, 7 insertions(+) > Reviewed-by: Rob Herring <robh@kernel.org> _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 2/3] dt-bindings: arm: at91: Document Kizbox3 HS board binding @ 2019-10-15 22:47 ` Rob Herring 0 siblings, 0 replies; 18+ messages in thread From: Rob Herring @ 2019-10-15 22:47 UTC (permalink / raw) To: Kamel Bouhara Cc: Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel, Thomas Petazzoni, devicetree, linux-kernel, Kamel Bouhara On Fri, 11 Oct 2019 14:50:21 +0200, Kamel Bouhara wrote: > Document devicetree binding of SAMA5D27 Kizbox3 HS board from Overkiz > SAS. > > Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> > --- > Documentation/devicetree/bindings/arm/atmel-at91.yaml | 7 +++++++ > 1 file changed, 7 insertions(+) > Reviewed-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH 3/3] ARM: at91: add Overkiz KIZBOX3 board 2019-10-11 12:50 ` Kamel Bouhara @ 2019-10-11 12:50 ` Kamel Bouhara -1 siblings, 0 replies; 18+ messages in thread From: Kamel Bouhara @ 2019-10-11 12:50 UTC (permalink / raw) To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel Cc: devicetree, Kamel Bouhara, Mickael GARDET, linux-kernel, Kévin RAYMOND, Thomas Petazzoni Add a common DT include file for the Kizbox3 boards. Add the devicetree for the Kizbox3 HS board. Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> Signed-off-by: Kévin RAYMOND <k.raymond@overkiz.com> Signed-off-by: Mickael GARDET <m.gardet@overkiz.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-kizbox3-hs.dts | 309 ++++++++++++++++ arch/arm/boot/dts/at91-kizbox3_common.dtsi | 412 +++++++++++++++++++++ 3 files changed, 722 insertions(+) create mode 100644 arch/arm/boot/dts/at91-kizbox3-hs.dts create mode 100644 arch/arm/boot/dts/at91-kizbox3_common.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b21b3a64641a..3bda216c41be 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -46,6 +46,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \ at91sam9x35ek.dtb dtb-$(CONFIG_SOC_SAM_V7) += \ at91-kizbox2.dtb \ + at91-kizbox3-hs.dtb \ at91-nattis-2-natte-2.dtb \ at91-sama5d27_som1_ek.dtb \ at91-sama5d2_ptc_ek.dtb \ diff --git a/arch/arm/boot/dts/at91-kizbox3-hs.dts b/arch/arm/boot/dts/at91-kizbox3-hs.dts new file mode 100644 index 000000000000..8734e7f8939e --- /dev/null +++ b/arch/arm/boot/dts/at91-kizbox3-hs.dts @@ -0,0 +1,309 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * at91-kizbox3-hs.dts - Device Tree file for Overkiz KIZBOX3-HS board + * + * Copyright (C) 2018 Overkiz SAS + * + * Authors: Dorian Rocipon <d.rocipon@overkiz.com> + * Kevin Carli <k.carli@overkiz.com> + * Mickael Gardet <m.gardet@overkiz.com> + */ +/dts-v1/; +#include "at91-kizbox3_common.dtsi" + +/ { + model = "Overkiz KIZBOX3-HS"; + compatible = "overkiz,kizbox3-hs", "atmel,sama5d2", "atmel,sama5"; + + pwm_leds { + status = "okay"; + + red { + status = "okay"; + }; + + green { + status = "okay"; + }; + + blue { + status = "okay"; + }; + + white { + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led_red + &pinctrl_led_white>; + status = "okay"; + + red { + label = "pio:red:user"; + gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + white { + label = "pio:white:user"; + gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default" , "default", "default", + "default", "default" ; + pinctrl-0 = <&pinctrl_key_gpio_default>; + pinctrl-1 = <&pinctrl_pio_rf &pinctrl_pio_wifi>; + pinctrl-2 = <&pinctrl_pio_io_boot + &pinctrl_pio_io_reset + &pinctrl_pio_io_test_radio>; + pinctrl-3 = <&pinctrl_pio_zbe_test_radio + &pinctrl_pio_zbe_rst>; + pinctrl-4 = <&pinctrl_pio_input>; + + SW1 { + label = "SW1"; + gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>; + linux,code = <0x101>; + wakeup-source; + }; + + SW2 { + label = "SW2"; + gpios = <&pioA PIN_PA18 GPIO_ACTIVE_LOW>; + linux,code = <0x102>; + wakeup-source; + }; + + SW3 { + label = "SW3"; + gpios = <&pioA PIN_PA22 GPIO_ACTIVE_LOW>; + linux,code = <0x103>; + wakeup-source; + }; + + SW7 { + label = "SW7"; + gpios = <&pioA PIN_PA26 GPIO_ACTIVE_LOW>; + linux,code = <0x107>; + wakeup-source; + }; + + SW8 { + label = "SW8"; + gpios = <&pioA PIN_PA24 GPIO_ACTIVE_LOW>; + linux,code = <0x108>; + wakeup-source; + }; + }; + + gpios { + compatible = "gpio"; + status = "okay"; + + rf_on { + label = "rf on"; + gpio = <&pioA PIN_PC19 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + wifi_on { + label = "wifi on"; + gpio = <&pioA PIN_PC20 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + zbe_test_radio { + label = "zbe test radio"; + gpio = <&pioA PIN_PB21 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + zbe_rst { + label = "zbe rst"; + gpio = <&pioA PIN_PB25 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + io_reset { + label = "io reset"; + gpio = <&pioA PIN_PB30 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + io_test_radio { + label = "io test radio"; + gpio = <&pioA PIN_PC9 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + io_boot_0 { + label = "io boot 0"; + gpio = <&pioA PIN_PC11 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + io_boot_1 { + label = "io boot 1"; + gpio = <&pioA PIN_PC17 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + verbose_bootloader { + label = "verbose bootloader"; + gpio = <&pioA PIN_PB11 GPIO_ACTIVE_HIGH>; + input; + }; + + nail_bed_detection { + label = "nail bed detection"; + gpio = <&pioA PIN_PB12 GPIO_ACTIVE_HIGH>; + input; + }; + + id_usba { + label = "id usba"; + gpio = <&pioA PIN_PC0 GPIO_ACTIVE_LOW>; + input; + }; + }; +}; + +&pioA { + pinctrl_key_gpio_default: key_gpio_default { + pinmux= <PIN_PA22__GPIO>, + <PIN_PA24__GPIO>, + <PIN_PA26__GPIO>, + <PIN_PA29__GPIO>, + <PIN_PA18__GPIO>; + bias-disable; + }; + + pinctrl_gpio { + pinctrl_pio_rf: gpio_rf { + pinmux = <PIN_PC19__GPIO>; + bias-disable; + }; + pinctrl_pio_wifi: gpio_wifi { + pinmux = <PIN_PC20__GPIO>; + bias-disable; + }; + pinctrl_pio_io_boot: gpio_io_boot { + pinmux = + <PIN_PC11__GPIO>, + <PIN_PC17__GPIO>; + bias-disable; + }; + pinctrl_pio_io_test_radio: gpio_io_test_radio { + pinmux = <PIN_PC9__GPIO>; + bias-disable; + }; + pinctrl_pio_zbe_test_radio: gpio_zbe_test_radio { + pinmux = <PIN_PB21__GPIO>; + bias-disable; + }; + pinctrl_pio_zbe_rst: gpio_zbe_rst { + pinmux = <PIN_PB25__GPIO>; + bias-disable; + }; + /* stm32 reset must be open drain (internal pull up) */ + pinctrl_pio_io_reset: gpio_io_reset { + pinmux = <PIN_PB30__GPIO>; + bias-disable; + drive-open-drain = <1>; + output-low; + }; + pinctrl_pio_input: gpio_input { + pinmux = + <PIN_PB11__GPIO>, + <PIN_PB12__GPIO>, + <PIN_PC0__GPIO>; + bias-disable; + }; + }; + + pinctrl_leds { + pinctrl_led_red: led_red { + pinmux = <PIN_PB1__GPIO>; + bias-disable; + }; + pinctrl_led_white: led_white { + pinmux = <PIN_PB8__GPIO>; + bias-disable; + }; + }; +}; + +&adc { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&flx0 { + status = "okay"; + + uart5: serial@200 { + status = "okay"; + }; +}; + +&flx3 { + status = "okay"; + uart6: serial@200 { + status = "okay"; + }; +}; + +&flx4 { + status = "okay"; + + i2c2: i2c@600 { + status = "okay"; + }; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/at91-kizbox3_common.dtsi new file mode 100644 index 000000000000..299e74d23184 --- /dev/null +++ b/arch/arm/boot/dts/at91-kizbox3_common.dtsi @@ -0,0 +1,412 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * at91-kizbox3.dts - Device Tree Include file for Overkiz Kizbox 3 + * family SoC boards + * + * Copyright (C) 2018 Overkiz SAS + * + * Authors: Dorian Rocipon <d.rocipon@overkiz.com> + * Kevin Carli <k.carli@overkiz.com> + * Mickael Gardet <m.gardet@overkiz.com> + */ +/dts-v1/; +#include "sama5d2.dtsi" +#include "sama5d2-pinfunc.h" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/atmel-flexcom.h> +#include <dt-bindings/pinctrl/at91.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "Overkiz Kizbox3"; + compatible = "overkiz,kizbox3", "atmel,sama5d2", "atmel,sama5"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + serial6 = &uart6; + }; + + chosen { + bootargs = "ubi.mtd=ubi"; + stdout-path = "serial1:115200n8"; + }; + + clocks { + slow_xtal { + clock-frequency = <32768>; + }; + + main_xtal { + clock-frequency = <12000000>; + }; + }; + + vdd_adc_vddana: supply_3v3_ana { + compatible = "regulator-fixed"; + regulator-name = "adc-vddana"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_adc_vref: supply_3v3_ref { + compatible = "regulator-fixed"; + regulator-name = "adc-vref"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + pwm_leds { + compatible = "pwm-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_pwm_h0 + &pinctrl_pwm0_pwm_h1 + &pinctrl_pwm0_pwm_h2 + &pinctrl_pwm0_pwm_h3>; + status = "disabled"; + + red { + label = "pwm:red:user"; + pwms = <&pwm0 0 10000000 0>; + max-brightness = <255>; + linux,default-trigger = "default-on"; + status = "disabled"; + }; + + green { + label = "pwm:green:user"; + pwms = <&pwm0 1 10000000 0>; + max-brightness = <255>; + linux,default-trigger = "default-on"; + status = "disabled"; + }; + + blue { + label = "pwm:blue:user"; + pwms = <&pwm0 2 10000000 0>; + max-brightness = <255>; + status = "disabled"; + }; + + white { + label = "pwm:white:user"; + pwms = <&pwm0 3 10000000 0>; + max-brightness = <255>; + status = "disabled"; + }; + }; +}; + +&ebi { + status = "okay"; +}; + +&nand_controller { + status = "okay"; + + nand@3 { + pinctrl-0 = <&pinctrl_ebi_nand_addr>; + pinctrl-names = "default"; + reg = <0x3 0x0 0x800000>; + + atmel,rb = <0>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-on-flash-bbt; + label = "atmel_nand"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + bootstrap@0 { + label = "bootstrap"; + reg = <0x0 0x20000>; + }; + + u-boot@20000 { + label = "u-boot"; + reg = <0x20000 0x140000>; + }; + + u-boot-factory@160000 { + label = "u-boot-factory"; + reg = <0x160000 0x140000>; + }; + + ubi@2A0000 { + label = "ubi"; + reg = <0x2A0000 0x7D60000>; + }; + }; + + }; +}; + +&rtc { + status = "okay"; +}; + +&pioA { + pinctrl_ebi_nand_addr: ebi-addr-1 { + pinmux = <PIN_PA0__D0>, + <PIN_PA1__D1>, + <PIN_PA2__D2>, + <PIN_PA3__D3>, + <PIN_PA4__D4>, + <PIN_PA5__D5>, + <PIN_PA6__D6>, + <PIN_PA7__D7>, + <PIN_PA8__NWE_NANDWE>, + <PIN_PA9__NCS3>, + <PIN_PA10__A21_NANDALE>, + <PIN_PA11__A22_NANDCLE>, + <PIN_PA21__NANDRDY>; + bias-disable; + }; + + pinctrl_usart { + pinctrl_usart_0: usart0-0 { + pinmux = < PIN_PB26__URXD0>, <PIN_PB27__UTXD0>; + bias-disable; + }; + pinctrl_usart_1: usart1-0 { + pinmux = < PIN_PD2__URXD1>, <PIN_PD3__UTXD1>; + bias-disable; + }; + pinctrl_usart_2: usart2-0 { + pinmux = < PIN_PD4__URXD2>, <PIN_PD5__UTXD2>; + bias-disable; + }; + pinctrl_usart_3: usart3-0 { + pinmux = < PIN_PC12__URXD3>, <PIN_PC13__UTXD3>; + bias-disable; + }; + pinctrl_usart_4: usart4-0 { + pinmux = < PIN_PB3__URXD4>, <PIN_PB4__UTXD4>; + bias-disable; + }; + pinctrl_flx0_default: flx0_usart_default { + pinmux = <PIN_PB28__FLEXCOM0_IO0>, //TX + <PIN_PB29__FLEXCOM0_IO1>; //RX + bias-disable; + }; + pinctrl_flx3_default: flx3_usart_default { + pinmux = <PIN_PB22__FLEXCOM3_IO1>, //RX + <PIN_PB23__FLEXCOM3_IO0>; //TX + bias-disable; + }; + }; + + pinctrl_flx4_default: flx4_i2c2_default { + pinmux = <PIN_PD12__FLEXCOM4_IO0>, //DATA + <PIN_PD13__FLEXCOM4_IO1>; //CLK + bias-disable; + drive-open-drain = <1>; + }; + + pinctrl_pwm0 { + pinctrl_pwm0_pwm_h0: pwm0_pwm_h0 { + pinmux = <PIN_PA30__PWMH0>; + bias-disable; + }; + pinctrl_pwm0_pwm_h1: pwm0_pwmh1 { + pinmux = <PIN_PB0__PWMH1>; + bias-disable; + }; + pinctrl_pwm0_pwm_h2: pwm0_pwm_h2 { + pinmux = <PIN_PB5__PWMH2>; + bias-disable; + }; + pinctrl_pwm0_pwm_h3: pwm0_pwm_h3 { + pinmux = <PIN_PB7__PWMH3>; + bias-disable; + }; + }; + + pinctrl_adc { + pinctrl_adc2: adc2 { + pinmux = <PIN_PD21__GPIO>; + bias-disable; + }; + pinctrl_adc3: adc3 { + pinmux = <PIN_PD22__GPIO>; + bias-disable; + }; + pinctrl_adc4: adc4 { + pinmux = <PIN_PD23__GPIO>; + bias-disable; + }; + pinctrl_adc5: adc5 { + pinmux = <PIN_PD24__GPIO>; + bias-disable; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_0>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +/* debug uart */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_1>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_2>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_3>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +&flx0 { + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>; + status = "disabled"; + + uart5: serial@200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0x200 0x400>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(11))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(12))>; + dma-names = "tx", "rx"; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; + clock-names = "usart"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx0_default>; + atmel,fifo-size = <32>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; +}; + +&flx3 { + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>; + status = "disabled"; + + uart6: serial@200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0x200 0x400>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(17))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(18))>; + dma-names = "tx", "rx"; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; + clock-names = "usart"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx3_default>; + atmel,fifo-size = <32>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; +}; + +&flx4 { + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>; + status = "disabled"; + + i2c2: i2c@600 { + compatible = "atmel,sama5d2-i2c"; + reg = <0x600 0x200>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(19))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(20))>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx4_default>; + atmel,fifo-size = <16>; + status = "disabled"; + }; +}; + +&pwm0 { + status = "okay"; +}; + +&shutdown_controller { + atmel,shdwc-debouncer = <976>; + atmel,wakeup-rtc-timer; + + input@0 { + reg = <0>; + atmel,wakeup-type = "low"; + }; +}; + +&watchdog { + status = "okay"; +}; + +&adc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc2 + &pinctrl_adc3 + &pinctrl_adc4 + &pinctrl_adc5>; + + vddana-supply = <&vdd_adc_vddana>; + vref-supply = <&vdd_adc_vref>; + status = "disabled"; +}; + +&securam { + export; + + /* export overkiz u-boot mode/version and factory */ + uboot@1400 { + reg = <0x1400 0x20>; + export; + }; +}; -- 2.23.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH 3/3] ARM: at91: add Overkiz KIZBOX3 board @ 2019-10-11 12:50 ` Kamel Bouhara 0 siblings, 0 replies; 18+ messages in thread From: Kamel Bouhara @ 2019-10-11 12:50 UTC (permalink / raw) To: Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel Cc: Thomas Petazzoni, devicetree, linux-kernel, Kamel Bouhara, Kévin RAYMOND, Mickael GARDET Add a common DT include file for the Kizbox3 boards. Add the devicetree for the Kizbox3 HS board. Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com> Signed-off-by: Kévin RAYMOND <k.raymond@overkiz.com> Signed-off-by: Mickael GARDET <m.gardet@overkiz.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-kizbox3-hs.dts | 309 ++++++++++++++++ arch/arm/boot/dts/at91-kizbox3_common.dtsi | 412 +++++++++++++++++++++ 3 files changed, 722 insertions(+) create mode 100644 arch/arm/boot/dts/at91-kizbox3-hs.dts create mode 100644 arch/arm/boot/dts/at91-kizbox3_common.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b21b3a64641a..3bda216c41be 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -46,6 +46,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \ at91sam9x35ek.dtb dtb-$(CONFIG_SOC_SAM_V7) += \ at91-kizbox2.dtb \ + at91-kizbox3-hs.dtb \ at91-nattis-2-natte-2.dtb \ at91-sama5d27_som1_ek.dtb \ at91-sama5d2_ptc_ek.dtb \ diff --git a/arch/arm/boot/dts/at91-kizbox3-hs.dts b/arch/arm/boot/dts/at91-kizbox3-hs.dts new file mode 100644 index 000000000000..8734e7f8939e --- /dev/null +++ b/arch/arm/boot/dts/at91-kizbox3-hs.dts @@ -0,0 +1,309 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * at91-kizbox3-hs.dts - Device Tree file for Overkiz KIZBOX3-HS board + * + * Copyright (C) 2018 Overkiz SAS + * + * Authors: Dorian Rocipon <d.rocipon@overkiz.com> + * Kevin Carli <k.carli@overkiz.com> + * Mickael Gardet <m.gardet@overkiz.com> + */ +/dts-v1/; +#include "at91-kizbox3_common.dtsi" + +/ { + model = "Overkiz KIZBOX3-HS"; + compatible = "overkiz,kizbox3-hs", "atmel,sama5d2", "atmel,sama5"; + + pwm_leds { + status = "okay"; + + red { + status = "okay"; + }; + + green { + status = "okay"; + }; + + blue { + status = "okay"; + }; + + white { + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led_red + &pinctrl_led_white>; + status = "okay"; + + red { + label = "pio:red:user"; + gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + white { + label = "pio:white:user"; + gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default" , "default", "default", + "default", "default" ; + pinctrl-0 = <&pinctrl_key_gpio_default>; + pinctrl-1 = <&pinctrl_pio_rf &pinctrl_pio_wifi>; + pinctrl-2 = <&pinctrl_pio_io_boot + &pinctrl_pio_io_reset + &pinctrl_pio_io_test_radio>; + pinctrl-3 = <&pinctrl_pio_zbe_test_radio + &pinctrl_pio_zbe_rst>; + pinctrl-4 = <&pinctrl_pio_input>; + + SW1 { + label = "SW1"; + gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>; + linux,code = <0x101>; + wakeup-source; + }; + + SW2 { + label = "SW2"; + gpios = <&pioA PIN_PA18 GPIO_ACTIVE_LOW>; + linux,code = <0x102>; + wakeup-source; + }; + + SW3 { + label = "SW3"; + gpios = <&pioA PIN_PA22 GPIO_ACTIVE_LOW>; + linux,code = <0x103>; + wakeup-source; + }; + + SW7 { + label = "SW7"; + gpios = <&pioA PIN_PA26 GPIO_ACTIVE_LOW>; + linux,code = <0x107>; + wakeup-source; + }; + + SW8 { + label = "SW8"; + gpios = <&pioA PIN_PA24 GPIO_ACTIVE_LOW>; + linux,code = <0x108>; + wakeup-source; + }; + }; + + gpios { + compatible = "gpio"; + status = "okay"; + + rf_on { + label = "rf on"; + gpio = <&pioA PIN_PC19 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + wifi_on { + label = "wifi on"; + gpio = <&pioA PIN_PC20 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + zbe_test_radio { + label = "zbe test radio"; + gpio = <&pioA PIN_PB21 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + zbe_rst { + label = "zbe rst"; + gpio = <&pioA PIN_PB25 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + io_reset { + label = "io reset"; + gpio = <&pioA PIN_PB30 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + io_test_radio { + label = "io test radio"; + gpio = <&pioA PIN_PC9 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + io_boot_0 { + label = "io boot 0"; + gpio = <&pioA PIN_PC11 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + io_boot_1 { + label = "io boot 1"; + gpio = <&pioA PIN_PC17 GPIO_ACTIVE_HIGH>; + output; + init-low; + }; + + verbose_bootloader { + label = "verbose bootloader"; + gpio = <&pioA PIN_PB11 GPIO_ACTIVE_HIGH>; + input; + }; + + nail_bed_detection { + label = "nail bed detection"; + gpio = <&pioA PIN_PB12 GPIO_ACTIVE_HIGH>; + input; + }; + + id_usba { + label = "id usba"; + gpio = <&pioA PIN_PC0 GPIO_ACTIVE_LOW>; + input; + }; + }; +}; + +&pioA { + pinctrl_key_gpio_default: key_gpio_default { + pinmux= <PIN_PA22__GPIO>, + <PIN_PA24__GPIO>, + <PIN_PA26__GPIO>, + <PIN_PA29__GPIO>, + <PIN_PA18__GPIO>; + bias-disable; + }; + + pinctrl_gpio { + pinctrl_pio_rf: gpio_rf { + pinmux = <PIN_PC19__GPIO>; + bias-disable; + }; + pinctrl_pio_wifi: gpio_wifi { + pinmux = <PIN_PC20__GPIO>; + bias-disable; + }; + pinctrl_pio_io_boot: gpio_io_boot { + pinmux = + <PIN_PC11__GPIO>, + <PIN_PC17__GPIO>; + bias-disable; + }; + pinctrl_pio_io_test_radio: gpio_io_test_radio { + pinmux = <PIN_PC9__GPIO>; + bias-disable; + }; + pinctrl_pio_zbe_test_radio: gpio_zbe_test_radio { + pinmux = <PIN_PB21__GPIO>; + bias-disable; + }; + pinctrl_pio_zbe_rst: gpio_zbe_rst { + pinmux = <PIN_PB25__GPIO>; + bias-disable; + }; + /* stm32 reset must be open drain (internal pull up) */ + pinctrl_pio_io_reset: gpio_io_reset { + pinmux = <PIN_PB30__GPIO>; + bias-disable; + drive-open-drain = <1>; + output-low; + }; + pinctrl_pio_input: gpio_input { + pinmux = + <PIN_PB11__GPIO>, + <PIN_PB12__GPIO>, + <PIN_PC0__GPIO>; + bias-disable; + }; + }; + + pinctrl_leds { + pinctrl_led_red: led_red { + pinmux = <PIN_PB1__GPIO>; + bias-disable; + }; + pinctrl_led_white: led_white { + pinmux = <PIN_PB8__GPIO>; + bias-disable; + }; + }; +}; + +&adc { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&flx0 { + status = "okay"; + + uart5: serial@200 { + status = "okay"; + }; +}; + +&flx3 { + status = "okay"; + uart6: serial@200 { + status = "okay"; + }; +}; + +&flx4 { + status = "okay"; + + i2c2: i2c@600 { + status = "okay"; + }; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/at91-kizbox3_common.dtsi new file mode 100644 index 000000000000..299e74d23184 --- /dev/null +++ b/arch/arm/boot/dts/at91-kizbox3_common.dtsi @@ -0,0 +1,412 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * at91-kizbox3.dts - Device Tree Include file for Overkiz Kizbox 3 + * family SoC boards + * + * Copyright (C) 2018 Overkiz SAS + * + * Authors: Dorian Rocipon <d.rocipon@overkiz.com> + * Kevin Carli <k.carli@overkiz.com> + * Mickael Gardet <m.gardet@overkiz.com> + */ +/dts-v1/; +#include "sama5d2.dtsi" +#include "sama5d2-pinfunc.h" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/atmel-flexcom.h> +#include <dt-bindings/pinctrl/at91.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "Overkiz Kizbox3"; + compatible = "overkiz,kizbox3", "atmel,sama5d2", "atmel,sama5"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + serial6 = &uart6; + }; + + chosen { + bootargs = "ubi.mtd=ubi"; + stdout-path = "serial1:115200n8"; + }; + + clocks { + slow_xtal { + clock-frequency = <32768>; + }; + + main_xtal { + clock-frequency = <12000000>; + }; + }; + + vdd_adc_vddana: supply_3v3_ana { + compatible = "regulator-fixed"; + regulator-name = "adc-vddana"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_adc_vref: supply_3v3_ref { + compatible = "regulator-fixed"; + regulator-name = "adc-vref"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + pwm_leds { + compatible = "pwm-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_pwm_h0 + &pinctrl_pwm0_pwm_h1 + &pinctrl_pwm0_pwm_h2 + &pinctrl_pwm0_pwm_h3>; + status = "disabled"; + + red { + label = "pwm:red:user"; + pwms = <&pwm0 0 10000000 0>; + max-brightness = <255>; + linux,default-trigger = "default-on"; + status = "disabled"; + }; + + green { + label = "pwm:green:user"; + pwms = <&pwm0 1 10000000 0>; + max-brightness = <255>; + linux,default-trigger = "default-on"; + status = "disabled"; + }; + + blue { + label = "pwm:blue:user"; + pwms = <&pwm0 2 10000000 0>; + max-brightness = <255>; + status = "disabled"; + }; + + white { + label = "pwm:white:user"; + pwms = <&pwm0 3 10000000 0>; + max-brightness = <255>; + status = "disabled"; + }; + }; +}; + +&ebi { + status = "okay"; +}; + +&nand_controller { + status = "okay"; + + nand@3 { + pinctrl-0 = <&pinctrl_ebi_nand_addr>; + pinctrl-names = "default"; + reg = <0x3 0x0 0x800000>; + + atmel,rb = <0>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-on-flash-bbt; + label = "atmel_nand"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + bootstrap@0 { + label = "bootstrap"; + reg = <0x0 0x20000>; + }; + + u-boot@20000 { + label = "u-boot"; + reg = <0x20000 0x140000>; + }; + + u-boot-factory@160000 { + label = "u-boot-factory"; + reg = <0x160000 0x140000>; + }; + + ubi@2A0000 { + label = "ubi"; + reg = <0x2A0000 0x7D60000>; + }; + }; + + }; +}; + +&rtc { + status = "okay"; +}; + +&pioA { + pinctrl_ebi_nand_addr: ebi-addr-1 { + pinmux = <PIN_PA0__D0>, + <PIN_PA1__D1>, + <PIN_PA2__D2>, + <PIN_PA3__D3>, + <PIN_PA4__D4>, + <PIN_PA5__D5>, + <PIN_PA6__D6>, + <PIN_PA7__D7>, + <PIN_PA8__NWE_NANDWE>, + <PIN_PA9__NCS3>, + <PIN_PA10__A21_NANDALE>, + <PIN_PA11__A22_NANDCLE>, + <PIN_PA21__NANDRDY>; + bias-disable; + }; + + pinctrl_usart { + pinctrl_usart_0: usart0-0 { + pinmux = < PIN_PB26__URXD0>, <PIN_PB27__UTXD0>; + bias-disable; + }; + pinctrl_usart_1: usart1-0 { + pinmux = < PIN_PD2__URXD1>, <PIN_PD3__UTXD1>; + bias-disable; + }; + pinctrl_usart_2: usart2-0 { + pinmux = < PIN_PD4__URXD2>, <PIN_PD5__UTXD2>; + bias-disable; + }; + pinctrl_usart_3: usart3-0 { + pinmux = < PIN_PC12__URXD3>, <PIN_PC13__UTXD3>; + bias-disable; + }; + pinctrl_usart_4: usart4-0 { + pinmux = < PIN_PB3__URXD4>, <PIN_PB4__UTXD4>; + bias-disable; + }; + pinctrl_flx0_default: flx0_usart_default { + pinmux = <PIN_PB28__FLEXCOM0_IO0>, //TX + <PIN_PB29__FLEXCOM0_IO1>; //RX + bias-disable; + }; + pinctrl_flx3_default: flx3_usart_default { + pinmux = <PIN_PB22__FLEXCOM3_IO1>, //RX + <PIN_PB23__FLEXCOM3_IO0>; //TX + bias-disable; + }; + }; + + pinctrl_flx4_default: flx4_i2c2_default { + pinmux = <PIN_PD12__FLEXCOM4_IO0>, //DATA + <PIN_PD13__FLEXCOM4_IO1>; //CLK + bias-disable; + drive-open-drain = <1>; + }; + + pinctrl_pwm0 { + pinctrl_pwm0_pwm_h0: pwm0_pwm_h0 { + pinmux = <PIN_PA30__PWMH0>; + bias-disable; + }; + pinctrl_pwm0_pwm_h1: pwm0_pwmh1 { + pinmux = <PIN_PB0__PWMH1>; + bias-disable; + }; + pinctrl_pwm0_pwm_h2: pwm0_pwm_h2 { + pinmux = <PIN_PB5__PWMH2>; + bias-disable; + }; + pinctrl_pwm0_pwm_h3: pwm0_pwm_h3 { + pinmux = <PIN_PB7__PWMH3>; + bias-disable; + }; + }; + + pinctrl_adc { + pinctrl_adc2: adc2 { + pinmux = <PIN_PD21__GPIO>; + bias-disable; + }; + pinctrl_adc3: adc3 { + pinmux = <PIN_PD22__GPIO>; + bias-disable; + }; + pinctrl_adc4: adc4 { + pinmux = <PIN_PD23__GPIO>; + bias-disable; + }; + pinctrl_adc5: adc5 { + pinmux = <PIN_PD24__GPIO>; + bias-disable; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_0>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +/* debug uart */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_1>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_2>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_3>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usart_4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; +}; + +&flx0 { + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>; + status = "disabled"; + + uart5: serial@200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0x200 0x400>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(11))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(12))>; + dma-names = "tx", "rx"; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; + clock-names = "usart"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx0_default>; + atmel,fifo-size = <32>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; +}; + +&flx3 { + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>; + status = "disabled"; + + uart6: serial@200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0x200 0x400>; + interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(17))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(18))>; + dma-names = "tx", "rx"; + clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; + clock-names = "usart"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx3_default>; + atmel,fifo-size = <32>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; +}; + +&flx4 { + atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>; + status = "disabled"; + + i2c2: i2c@600 { + compatible = "atmel,sama5d2-i2c"; + reg = <0x600 0x200>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(19))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(20))>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flx4_default>; + atmel,fifo-size = <16>; + status = "disabled"; + }; +}; + +&pwm0 { + status = "okay"; +}; + +&shutdown_controller { + atmel,shdwc-debouncer = <976>; + atmel,wakeup-rtc-timer; + + input@0 { + reg = <0>; + atmel,wakeup-type = "low"; + }; +}; + +&watchdog { + status = "okay"; +}; + +&adc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc2 + &pinctrl_adc3 + &pinctrl_adc4 + &pinctrl_adc5>; + + vddana-supply = <&vdd_adc_vddana>; + vref-supply = <&vdd_adc_vref>; + status = "disabled"; +}; + +&securam { + export; + + /* export overkiz u-boot mode/version and factory */ + uboot@1400 { + reg = <0x1400 0x20>; + export; + }; +}; -- 2.23.0 ^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: at91: add Overkiz KIZBOX3 board 2019-10-11 12:50 ` Kamel Bouhara (?) (?) @ 2019-10-14 4:49 ` kbuild test robot -1 siblings, 0 replies; 18+ messages in thread From: kbuild test robot @ 2019-10-14 4:49 UTC (permalink / raw) To: Kamel Bouhara Cc: devicetree, Alexandre Belloni, kbuild-all, Kamel Bouhara, Mickael GARDET, linux-kernel, Ludovic Desroches, Rob Herring, Thomas Petazzoni, Kévin RAYMOND, linux-arm-kernel [-- Attachment #1: Type: text/plain, Size: 1353 bytes --] Hi Kamel, Thank you for the patch! Yet something to improve: [auto build test ERROR on robh/for-next] [cannot apply to v5.4-rc3 next-20191011] [if your patch is applied to the wrong git tree, please drop us a note to help improve the system. BTW, we also suggest to use '--base' option to specify the base tree in git format-patch, please see https://stackoverflow.com/a/37406982] url: https://github.com/0day-ci/linux/commits/Kamel-Bouhara/Add-new-Overkiz-Kizbox3-support/20191014-054232 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm-allmodconfig (attached as .config) compiler: arm-linux-gnueabi-gcc (GCC) 7.4.0 reproduce: wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # save the attached .config to linux build tree GCC_VERSION=7.4.0 make.cross ARCH=arm If you fix the issue, kindly add following tag Reported-by: kbuild test robot <lkp@intel.com> All errors (new ones prefixed by >>): >> Error: arch/arm/boot/dts/at91-kizbox3_common.dtsi:155.1-5 Label or path rtc not found FATAL ERROR: Syntax error parsing input tree --- 0-DAY kernel test infrastructure Open Source Technology Center https://lists.01.org/pipermail/kbuild-all Intel Corporation [-- Attachment #2: .config.gz --] [-- Type: application/gzip, Size: 71975 bytes --] [-- Attachment #3: Type: text/plain, Size: 176 bytes --] _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: at91: add Overkiz KIZBOX3 board @ 2019-10-14 4:49 ` kbuild test robot 0 siblings, 0 replies; 18+ messages in thread From: kbuild test robot @ 2019-10-14 4:49 UTC (permalink / raw) To: Kamel Bouhara Cc: kbuild-all, Rob Herring, Nicolas Ferre, Alexandre Belloni, Ludovic Desroches, linux-arm-kernel, Thomas Petazzoni, devicetree, linux-kernel, Kamel Bouhara, Kévin RAYMOND, Mickael GARDET [-- Attachment #1: Type: text/plain, Size: 1353 bytes --] Hi Kamel, Thank you for the patch! Yet something to improve: [auto build test ERROR on robh/for-next] [cannot apply to v5.4-rc3 next-20191011] [if your patch is applied to the wrong git tree, please drop us a note to help improve the system. BTW, we also suggest to use '--base' option to specify the base tree in git format-patch, please see https://stackoverflow.com/a/37406982] url: https://github.com/0day-ci/linux/commits/Kamel-Bouhara/Add-new-Overkiz-Kizbox3-support/20191014-054232 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm-allmodconfig (attached as .config) compiler: arm-linux-gnueabi-gcc (GCC) 7.4.0 reproduce: wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # save the attached .config to linux build tree GCC_VERSION=7.4.0 make.cross ARCH=arm If you fix the issue, kindly add following tag Reported-by: kbuild test robot <lkp@intel.com> All errors (new ones prefixed by >>): >> Error: arch/arm/boot/dts/at91-kizbox3_common.dtsi:155.1-5 Label or path rtc not found FATAL ERROR: Syntax error parsing input tree --- 0-DAY kernel test infrastructure Open Source Technology Center https://lists.01.org/pipermail/kbuild-all Intel Corporation [-- Attachment #2: .config.gz --] [-- Type: application/gzip, Size: 71975 bytes --] ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: at91: add Overkiz KIZBOX3 board @ 2019-10-14 4:49 ` kbuild test robot 0 siblings, 0 replies; 18+ messages in thread From: kbuild test robot @ 2019-10-14 4:49 UTC (permalink / raw) To: kbuild-all [-- Attachment #1: Type: text/plain, Size: 1384 bytes --] Hi Kamel, Thank you for the patch! Yet something to improve: [auto build test ERROR on robh/for-next] [cannot apply to v5.4-rc3 next-20191011] [if your patch is applied to the wrong git tree, please drop us a note to help improve the system. BTW, we also suggest to use '--base' option to specify the base tree in git format-patch, please see https://stackoverflow.com/a/37406982] url: https://github.com/0day-ci/linux/commits/Kamel-Bouhara/Add-new-Overkiz-Kizbox3-support/20191014-054232 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm-allmodconfig (attached as .config) compiler: arm-linux-gnueabi-gcc (GCC) 7.4.0 reproduce: wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # save the attached .config to linux build tree GCC_VERSION=7.4.0 make.cross ARCH=arm If you fix the issue, kindly add following tag Reported-by: kbuild test robot <lkp@intel.com> All errors (new ones prefixed by >>): >> Error: arch/arm/boot/dts/at91-kizbox3_common.dtsi:155.1-5 Label or path rtc not found FATAL ERROR: Syntax error parsing input tree --- 0-DAY kernel test infrastructure Open Source Technology Center https://lists.01.org/pipermail/kbuild-all Intel Corporation [-- Attachment #2: config.gz --] [-- Type: application/gzip, Size: 71975 bytes --] ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 3/3] ARM: at91: add Overkiz KIZBOX3 board @ 2019-10-14 4:49 ` kbuild test robot 0 siblings, 0 replies; 18+ messages in thread From: kbuild test robot @ 2019-10-14 4:49 UTC (permalink / raw) Cc: devicetree, Alexandre Belloni, kbuild-all, Kamel Bouhara, Mickael GARDET, linux-kernel, Ludovic Desroches, Rob Herring, Thomas Petazzoni, Kévin RAYMOND, linux-arm-kernel [-- Attachment #1: Type: text/plain, Size: 1353 bytes --] Hi Kamel, Thank you for the patch! Yet something to improve: [auto build test ERROR on robh/for-next] [cannot apply to v5.4-rc3 next-20191011] [if your patch is applied to the wrong git tree, please drop us a note to help improve the system. BTW, we also suggest to use '--base' option to specify the base tree in git format-patch, please see https://stackoverflow.com/a/37406982] url: https://github.com/0day-ci/linux/commits/Kamel-Bouhara/Add-new-Overkiz-Kizbox3-support/20191014-054232 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm-allmodconfig (attached as .config) compiler: arm-linux-gnueabi-gcc (GCC) 7.4.0 reproduce: wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # save the attached .config to linux build tree GCC_VERSION=7.4.0 make.cross ARCH=arm If you fix the issue, kindly add following tag Reported-by: kbuild test robot <lkp@intel.com> All errors (new ones prefixed by >>): >> Error: arch/arm/boot/dts/at91-kizbox3_common.dtsi:155.1-5 Label or path rtc not found FATAL ERROR: Syntax error parsing input tree --- 0-DAY kernel test infrastructure Open Source Technology Center https://lists.01.org/pipermail/kbuild-all Intel Corporation [-- Attachment #2: .config.gz --] [-- Type: application/gzip, Size: 71975 bytes --] [-- Attachment #3: Type: text/plain, Size: 176 bytes --] _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 0/3] Add new Overkiz Kizbox3 support 2019-10-11 12:50 ` Kamel Bouhara @ 2019-10-16 8:08 ` Alexandre Belloni -1 siblings, 0 replies; 18+ messages in thread From: Alexandre Belloni @ 2019-10-16 8:08 UTC (permalink / raw) To: Kamel Bouhara Cc: devicetree, linux-kernel, Ludovic Desroches, Rob Herring, Thomas Petazzoni, linux-arm-kernel On 11/10/2019 14:50:19+0200, Kamel Bouhara wrote: > Add support for the Kizbox3 Overkiz SAS boards. > Those boards are based on the Atmel SAMA5D27 SoC. > > Kamel Bouhara (3): > dt-bindings: Add vendor prefix for Overkiz SAS > dt-bindings: arm: at91: Document Kizbox3 HS board binding > ARM: at91: add Overkiz KIZBOX3 board > > .../devicetree/bindings/arm/atmel-at91.yaml | 7 + > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/at91-kizbox3-hs.dts | 309 +++++++++++++ > arch/arm/boot/dts/at91-kizbox3_common.dtsi | 412 ++++++++++++++++++ > 5 files changed, 731 insertions(+) > create mode 100644 arch/arm/boot/dts/at91-kizbox3-hs.dts > create mode 100644 arch/arm/boot/dts/at91-kizbox3_common.dtsi > All applied, thanks. -- Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH 0/3] Add new Overkiz Kizbox3 support @ 2019-10-16 8:08 ` Alexandre Belloni 0 siblings, 0 replies; 18+ messages in thread From: Alexandre Belloni @ 2019-10-16 8:08 UTC (permalink / raw) To: Kamel Bouhara Cc: Rob Herring, Nicolas Ferre, Ludovic Desroches, linux-arm-kernel, Thomas Petazzoni, devicetree, linux-kernel On 11/10/2019 14:50:19+0200, Kamel Bouhara wrote: > Add support for the Kizbox3 Overkiz SAS boards. > Those boards are based on the Atmel SAMA5D27 SoC. > > Kamel Bouhara (3): > dt-bindings: Add vendor prefix for Overkiz SAS > dt-bindings: arm: at91: Document Kizbox3 HS board binding > ARM: at91: add Overkiz KIZBOX3 board > > .../devicetree/bindings/arm/atmel-at91.yaml | 7 + > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/at91-kizbox3-hs.dts | 309 +++++++++++++ > arch/arm/boot/dts/at91-kizbox3_common.dtsi | 412 ++++++++++++++++++ > 5 files changed, 731 insertions(+) > create mode 100644 arch/arm/boot/dts/at91-kizbox3-hs.dts > create mode 100644 arch/arm/boot/dts/at91-kizbox3_common.dtsi > All applied, thanks. -- Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com ^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2019-10-16 8:08 UTC | newest] Thread overview: 18+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2019-10-11 12:50 [PATCH 0/3] Add new Overkiz Kizbox3 support Kamel Bouhara 2019-10-11 12:50 ` Kamel Bouhara 2019-10-11 12:50 ` [PATCH 1/3] dt-bindings: Add vendor prefix for Overkiz SAS Kamel Bouhara 2019-10-11 12:50 ` Kamel Bouhara 2019-10-15 22:46 ` Rob Herring 2019-10-15 22:46 ` Rob Herring 2019-10-11 12:50 ` [PATCH 2/3] dt-bindings: arm: at91: Document Kizbox3 HS board binding Kamel Bouhara 2019-10-11 12:50 ` Kamel Bouhara 2019-10-15 22:47 ` Rob Herring 2019-10-15 22:47 ` Rob Herring 2019-10-11 12:50 ` [PATCH 3/3] ARM: at91: add Overkiz KIZBOX3 board Kamel Bouhara 2019-10-11 12:50 ` Kamel Bouhara 2019-10-14 4:49 ` kbuild test robot 2019-10-14 4:49 ` kbuild test robot 2019-10-14 4:49 ` kbuild test robot 2019-10-14 4:49 ` kbuild test robot 2019-10-16 8:08 ` [PATCH 0/3] Add new Overkiz Kizbox3 support Alexandre Belloni 2019-10-16 8:08 ` Alexandre Belloni
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.