From: Miquel Raynal <miquel.raynal@bootlin.com>
To: Richard Weinberger <richard@nod.at>,
David Woodhouse <dwmw2@infradead.org>,
Brian Norris <computersforpeace@gmail.com>,
Marek Vasut <marek.vasut@gmail.com>,
Tudor Ambarus <Tudor.Ambarus@microchip.com>,
Vignesh Raghavendra <vigneshr@ti.com>
Cc: stable@vger.kernel.org,
Boris Brezillon <boris.brezillon@collabora.com>,
linux-mtd@lists.infradead.org,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
rmk+kernel@arm.linux.org.uk,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] mtd: spear_smi: Fix nonalignment not handled in memcpy_toio
Date: Fri, 18 Oct 2019 16:49:20 +0200 [thread overview]
Message-ID: <20191018164920.11250935@xps13> (raw)
In-Reply-To: <20191018143643.29676-1-miquel.raynal@bootlin.com>
Hello,
+Russell who might have thoughts about the issue
Miquel Raynal <miquel.raynal@bootlin.com> wrote on Fri, 18 Oct 2019
16:36:43 +0200:
> Any write with either dd or flashcp to a device driven by the
> spear_smi.c driver will pass through the spear_smi_cpy_toio()
> function. This function will get called for chunks of up to 256 bytes.
> If the amount of data is smaller, we may have a problem if the data
> length is not 4-byte aligned. In this situation, the kernel panics
> during the memcpy:
>
> # dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
> spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
> spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
> spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
> spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
> Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
> [...]
> PC is at memcpy+0xcc/0x330
>
> Workaround this issue by using the alternate _memcpy_toio() method
> which at least does not present the same problem.
>
> Fixes: f18dbbb1bfe0 ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
> Cc: stable@vger.kernel.org
> Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>
> Hello,
>
> This patch could not be tested with a mainline kernel (only compiled)
> but was tested with a stable 4.14.x kernel. I have really no idea why
> memcpy fails in this situation that's why I propose this workaround
> but I bet there is something deeper not working.
I did not mention that the opposite direction using memcpy_fromio() does
not present any issue.
>
> Thanks,
> Miquèl
>
> drivers/mtd/devices/spear_smi.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/mtd/devices/spear_smi.c b/drivers/mtd/devices/spear_smi.c
> index 986f81d2f93e..d888625a3244 100644
> --- a/drivers/mtd/devices/spear_smi.c
> +++ b/drivers/mtd/devices/spear_smi.c
> @@ -614,7 +614,7 @@ static inline int spear_smi_cpy_toio(struct spear_smi *dev, u32 bank,
> ctrlreg1 = readl(dev->io_base + SMI_CR1);
> writel((ctrlreg1 | WB_MODE) & ~SW_MODE, dev->io_base + SMI_CR1);
>
> - memcpy_toio(dest, src, len);
> + _memcpy_toio(dest, src, len);
>
> writel(ctrlreg1, dev->io_base + SMI_CR1);
>
Thanks,
Miquèl
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
WARNING: multiple messages have this Message-ID (diff)
From: Miquel Raynal <miquel.raynal@bootlin.com>
To: Richard Weinberger <richard@nod.at>,
David Woodhouse <dwmw2@infradead.org>,
Brian Norris <computersforpeace@gmail.com>,
Marek Vasut <marek.vasut@gmail.com>,
Tudor Ambarus <Tudor.Ambarus@microchip.com>,
Vignesh Raghavendra <vigneshr@ti.com>
Cc: stable@vger.kernel.org,
Boris Brezillon <boris.brezillon@collabora.com>,
linux-mtd@lists.infradead.org,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
rmk+kernel@arm.linux.org.uk,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH] mtd: spear_smi: Fix nonalignment not handled in memcpy_toio
Date: Fri, 18 Oct 2019 16:49:20 +0200 [thread overview]
Message-ID: <20191018164920.11250935@xps13> (raw)
In-Reply-To: <20191018143643.29676-1-miquel.raynal@bootlin.com>
Hello,
+Russell who might have thoughts about the issue
Miquel Raynal <miquel.raynal@bootlin.com> wrote on Fri, 18 Oct 2019
16:36:43 +0200:
> Any write with either dd or flashcp to a device driven by the
> spear_smi.c driver will pass through the spear_smi_cpy_toio()
> function. This function will get called for chunks of up to 256 bytes.
> If the amount of data is smaller, we may have a problem if the data
> length is not 4-byte aligned. In this situation, the kernel panics
> during the memcpy:
>
> # dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
> spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
> spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
> spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
> spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
> Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
> [...]
> PC is at memcpy+0xcc/0x330
>
> Workaround this issue by using the alternate _memcpy_toio() method
> which at least does not present the same problem.
>
> Fixes: f18dbbb1bfe0 ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
> Cc: stable@vger.kernel.org
> Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>
> Hello,
>
> This patch could not be tested with a mainline kernel (only compiled)
> but was tested with a stable 4.14.x kernel. I have really no idea why
> memcpy fails in this situation that's why I propose this workaround
> but I bet there is something deeper not working.
I did not mention that the opposite direction using memcpy_fromio() does
not present any issue.
>
> Thanks,
> Miquèl
>
> drivers/mtd/devices/spear_smi.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/mtd/devices/spear_smi.c b/drivers/mtd/devices/spear_smi.c
> index 986f81d2f93e..d888625a3244 100644
> --- a/drivers/mtd/devices/spear_smi.c
> +++ b/drivers/mtd/devices/spear_smi.c
> @@ -614,7 +614,7 @@ static inline int spear_smi_cpy_toio(struct spear_smi *dev, u32 bank,
> ctrlreg1 = readl(dev->io_base + SMI_CR1);
> writel((ctrlreg1 | WB_MODE) & ~SW_MODE, dev->io_base + SMI_CR1);
>
> - memcpy_toio(dest, src, len);
> + _memcpy_toio(dest, src, len);
>
> writel(ctrlreg1, dev->io_base + SMI_CR1);
>
Thanks,
Miquèl
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Miquel Raynal <miquel.raynal@bootlin.com>
To: Richard Weinberger <richard@nod.at>,
David Woodhouse <dwmw2@infradead.org>,
Brian Norris <computersforpeace@gmail.com>,
Marek Vasut <marek.vasut@gmail.com>,
Tudor Ambarus <Tudor.Ambarus@microchip.com>,
Vignesh Raghavendra <vigneshr@ti.com>
Cc: <linux-mtd@lists.infradead.org>,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
<linux-arm-kernel@lists.infradead.org>,
stable@vger.kernel.org,
Boris Brezillon <boris.brezillon@collabora.com>,
rmk+kernel@arm.linux.org.uk
Subject: Re: [PATCH] mtd: spear_smi: Fix nonalignment not handled in memcpy_toio
Date: Fri, 18 Oct 2019 16:49:20 +0200 [thread overview]
Message-ID: <20191018164920.11250935@xps13> (raw)
In-Reply-To: <20191018143643.29676-1-miquel.raynal@bootlin.com>
Hello,
+Russell who might have thoughts about the issue
Miquel Raynal <miquel.raynal@bootlin.com> wrote on Fri, 18 Oct 2019
16:36:43 +0200:
> Any write with either dd or flashcp to a device driven by the
> spear_smi.c driver will pass through the spear_smi_cpy_toio()
> function. This function will get called for chunks of up to 256 bytes.
> If the amount of data is smaller, we may have a problem if the data
> length is not 4-byte aligned. In this situation, the kernel panics
> during the memcpy:
>
> # dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
> spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
> spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
> spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
> spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
> Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
> [...]
> PC is at memcpy+0xcc/0x330
>
> Workaround this issue by using the alternate _memcpy_toio() method
> which at least does not present the same problem.
>
> Fixes: f18dbbb1bfe0 ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
> Cc: stable@vger.kernel.org
> Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>
> Hello,
>
> This patch could not be tested with a mainline kernel (only compiled)
> but was tested with a stable 4.14.x kernel. I have really no idea why
> memcpy fails in this situation that's why I propose this workaround
> but I bet there is something deeper not working.
I did not mention that the opposite direction using memcpy_fromio() does
not present any issue.
>
> Thanks,
> Miquèl
>
> drivers/mtd/devices/spear_smi.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/mtd/devices/spear_smi.c b/drivers/mtd/devices/spear_smi.c
> index 986f81d2f93e..d888625a3244 100644
> --- a/drivers/mtd/devices/spear_smi.c
> +++ b/drivers/mtd/devices/spear_smi.c
> @@ -614,7 +614,7 @@ static inline int spear_smi_cpy_toio(struct spear_smi *dev, u32 bank,
> ctrlreg1 = readl(dev->io_base + SMI_CR1);
> writel((ctrlreg1 | WB_MODE) & ~SW_MODE, dev->io_base + SMI_CR1);
>
> - memcpy_toio(dest, src, len);
> + _memcpy_toio(dest, src, len);
>
> writel(ctrlreg1, dev->io_base + SMI_CR1);
>
Thanks,
Miquèl
next prev parent reply other threads:[~2019-10-18 14:49 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-18 14:36 [PATCH] mtd: spear_smi: Fix nonalignment not handled in memcpy_toio Miquel Raynal
2019-10-18 14:36 ` Miquel Raynal
2019-10-18 14:36 ` Miquel Raynal
2019-10-18 14:49 ` Miquel Raynal [this message]
2019-10-18 14:49 ` Miquel Raynal
2019-10-18 14:49 ` Miquel Raynal
2019-10-21 8:01 ` Boris Brezillon
2019-10-21 8:01 ` Boris Brezillon
2019-10-21 8:01 ` Boris Brezillon
2019-10-22 7:44 ` Miquel Raynal
2019-10-22 7:44 ` Miquel Raynal
2019-10-22 7:44 ` Miquel Raynal
2019-10-22 7:51 ` Miquel Raynal
2019-10-22 7:51 ` Miquel Raynal
2019-10-22 7:51 ` Miquel Raynal
2019-10-22 7:52 ` Thomas Petazzoni
2019-10-22 7:52 ` Thomas Petazzoni
2019-10-22 7:52 ` Thomas Petazzoni
2019-10-22 8:26 ` Russell King - ARM Linux admin
2019-10-22 8:26 ` Russell King - ARM Linux admin
2019-10-22 8:26 ` Russell King - ARM Linux admin
2019-10-22 9:17 ` Miquel Raynal
2019-10-22 9:17 ` Miquel Raynal
2019-10-22 9:17 ` Miquel Raynal
2019-10-22 9:26 ` Russell King - ARM Linux admin
2019-10-22 9:26 ` Russell King - ARM Linux admin
2019-10-22 9:26 ` Russell King - ARM Linux admin
2019-10-22 9:47 ` Miquel Raynal
2019-10-22 9:47 ` Miquel Raynal
2019-10-22 9:47 ` Miquel Raynal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191018164920.11250935@xps13 \
--to=miquel.raynal@bootlin.com \
--cc=Tudor.Ambarus@microchip.com \
--cc=boris.brezillon@collabora.com \
--cc=computersforpeace@gmail.com \
--cc=dwmw2@infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-mtd@lists.infradead.org \
--cc=marek.vasut@gmail.com \
--cc=richard@nod.at \
--cc=rmk+kernel@arm.linux.org.uk \
--cc=stable@vger.kernel.org \
--cc=thomas.petazzoni@bootlin.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.