Re: [alsa-devel] [PATCH v3 1/2] dt-bindings: soundwire: add bindings for Qcom controller

[Vinod Koul <vkoul@kernel.org>]

On 11-10-19, 16:44, Srinivas Kandagatla wrote:
> This patch adds bindings for Qualcomm soundwire controller.
> 
> Qualcomm SoundWire Master controller is present in most Qualcomm SoCs
> either integrated as part of WCD audio codecs via slimbus or
> as part of SOC I/O.
> 
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---
>  .../bindings/soundwire/qcom,sdw.txt           | 167 ++++++++++++++++++
>  1 file changed, 167 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/soundwire/qcom,sdw.txt
> 
> diff --git a/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt
> new file mode 100644
> index 000000000000..436547f3b155
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt
> @@ -0,0 +1,167 @@
> +Qualcomm SoundWire Controller Bindings
> +
> +
> +This binding describes the Qualcomm SoundWire Controller along with its
> +board specific bus parameters.
> +
> +- compatible:
> +	Usage: required
> +	Value type: <stringlist>
> +	Definition: must be "qcom,soundwire-v<MAJOR>.<MINOR>.<STEP>",
> +		    Example:
> +			"qcom,soundwire-v1.3.0"
> +			"qcom,soundwire-v1.5.0"
> +			"qcom,soundwire-v1.6.0"
> +- reg:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: the base address and size of SoundWire controller
> +		    address space.
> +
> +- interrupts:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: should specify the SoundWire Controller IRQ
> +
> +- clock-names:
> +	Usage: required
> +	Value type: <stringlist>
> +	Definition: should be "iface" for SoundWire Controller interface clock
> +
> +- clocks:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: should specify the SoundWire Controller interface clock
> +
> +- #sound-dai-cells:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: must be 1 for digital audio interfaces on the controller.
> +
> +- qcom,dout-ports:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: must be count of data out ports
> +
> +- qcom,din-ports:
> +	Usage: required
> +	Value type: <u32>
> +	Definition: must be count of data in ports
> +
> +- qcom,ports-offset1:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: should specify payload transport window offset1 of each
> +		    data port. Out ports followed by In ports.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.
> +
> +- qcom,ports-offset2:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: should specify payload transport window offset2 of each
> +		    data port. Out ports followed by In ports.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.

Do we need to define these two in DT? Would this not be allocated in
Software and programmed?

> +
> +- qcom,ports-sinterval-low:
> +	Usage: required
> +	Value type: <prop-encoded-array>
> +	Definition: should be sample interval low of each data port.
> +		    Out ports followed by In ports. Used for Sample Interval
> +		    calculation.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.
> +
> +- qcom,ports-word-length:
> +	Usage: optional
> +	Value type: <prop-encoded-array>
> +	Definition: should be size of payload channel sample.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.
> +
> +- qcom,ports-block-pack-mode:
> +	Usage: optional
> +	Value type: <prop-encoded-array>
> +	Definition: should be 0 or 1 to indicate the block packing mode.
> +		    0 to indicate Blocks are per Channel
> +		    1 to indicate Blocks are per Port.
> +		    Out ports followed by In ports.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.
> +
> +- qcom,ports-block-group-count:
> +	Usage: optional
> +	Value type: <prop-encoded-array>
> +	Definition: should be in range 1 to 4 to indicate how many sample
> +		    intervals are combined into a payload.
> +		    Out ports followed by In ports.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.
> +
> +- qcom,ports-lane-control:
> +	Usage: optional
> +	Value type: <prop-encoded-array>
> +	Definition: should be in range 0 to 7 to identify which	data lane
> +		    the data port uses.
> +		    Out ports followed by In ports.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.
> +
> +- qcom,ports-hstart:
> +	Usage: optional
> +	Value type: <prop-encoded-array>
> +	Definition: should be number identifying lowerst numbered coloum in
> +		    SoundWire Frame, i.e. left edge of the Transport sub-frame
> +		    for each port. Values between 0 and 15 are valid.
> +		    Out ports followed by In ports.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.
> +
> +- qcom,ports-hstop:
> +	Usage: optional
> +	Value type: <prop-encoded-array>
> +	Definition: should be number identifying highest numbered coloum in
> +		    SoundWire Frame, i.e. the right edge of the Transport
> +		    sub-frame for each port. Values between 0 and 15 are valid.
> +		    Out ports followed by In ports.
> +		    More info in MIPI Alliance SoundWire 1.0 Specifications.

Ditto with these two as well
-- 
~Vinod
_______________________________________________
Alsa-devel mailing list
Alsa-devel@alsa-project.org
https://mailman.alsa-project.org/mailman/listinfo/alsa-devel