All of lore.kernel.org
 help / color / mirror / Atom feed
From: Peng Ma <peng.ma@nxp.com>
To: "vkoul@kernel.org" <vkoul@kernel.org>,
	"robh+dt@kernel.org" <robh+dt@kernel.org>,
	"mark.rutland@arm.com" <mark.rutland@arm.com>,
	"shawnguo@kernel.org" <shawnguo@kernel.org>,
	Leo Li <leoyang.li@nxp.com>,
	"dan.j.williams@intel.com" <dan.j.williams@intel.com>,
	Robin Gong <yibin.gong@nxp.com>
Cc: "dmaengine@vger.kernel.org" <dmaengine@vger.kernel.org>,
	"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	"linux-arm-kernel@lists.infradead.org" 
	<linux-arm-kernel@lists.infradead.org>, Peng Ma <peng.ma@nxp.com>
Subject: [v4 1/2] dmaengine: fsl-edma: Add eDMA support for QorIQ LS1028A platform
Date: Wed, 11 Dec 2019 08:09:33 +0000	[thread overview]
Message-ID: <20191211080749.30751-1-peng.ma@nxp.com> (raw)

Our platforms(such as LS1021A, LS1012A, LS1043A, LS1046A, LS1028A) with
below registers(CHCFG0 - CHCFG15) of eDMA as follows:
*-----------------------------------------------------------*
|     Offset   |	OTHERS      |		LS1028A	    |
|--------------|--------------------|-----------------------|
|     0x0      |        CHCFG0      |           CHCFG3      |
|--------------|--------------------|-----------------------|
|     0x1      |        CHCFG1      |           CHCFG2      |
|--------------|--------------------|-----------------------|
|     0x2      |        CHCFG2      |           CHCFG1      |
|--------------|--------------------|-----------------------|
|     0x3      |        CHCFG3      |           CHCFG0      |
|--------------|--------------------|-----------------------|
|     ...      |        ......      |           ......      |
|--------------|--------------------|-----------------------|
|     0xC      |        CHCFG12     |           CHCFG15     |
|--------------|--------------------|-----------------------|
|     0xD      |        CHCFG13     |           CHCFG14     |
|--------------|--------------------|-----------------------|
|     0xE      |        CHCFG14     |           CHCFG13     |
|--------------|--------------------|-----------------------|
|     0xF      |        CHCFG15     |           CHCFG12     |
*-----------------------------------------------------------*

This patch is to improve edma driver to fit LS1028A platform.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
---
Changed for v4:
	- Add 'mux_swap' into 'struct fsl_edma_drvdata'
	- Remove soc match function  

 drivers/dma/fsl-edma-common.c | 5 +++++
 drivers/dma/fsl-edma-common.h | 1 +
 drivers/dma/fsl-edma.c        | 8 ++++++++
 3 files changed, 14 insertions(+)

diff --git a/drivers/dma/fsl-edma-common.c b/drivers/dma/fsl-edma-common.c
index b1a7ca91701a..5697c3622699 100644
--- a/drivers/dma/fsl-edma-common.c
+++ b/drivers/dma/fsl-edma-common.c
@@ -109,10 +109,15 @@ void fsl_edma_chan_mux(struct fsl_edma_chan *fsl_chan,
 	u32 ch = fsl_chan->vchan.chan.chan_id;
 	void __iomem *muxaddr;
 	unsigned int chans_per_mux, ch_off;
+	int endian_diff[4] = {3, 1, -1, -3};
 	u32 dmamux_nr = fsl_chan->edma->drvdata->dmamuxs;
 
 	chans_per_mux = fsl_chan->edma->n_chans / dmamux_nr;
 	ch_off = fsl_chan->vchan.chan.chan_id % chans_per_mux;
+
+	if (fsl_chan->edma->drvdata->mux_swap)
+		ch_off += endian_diff[ch_off % 4];
+
 	muxaddr = fsl_chan->edma->muxbase[ch / chans_per_mux];
 	slot = EDMAMUX_CHCFG_SOURCE(slot);
 
diff --git a/drivers/dma/fsl-edma-common.h b/drivers/dma/fsl-edma-common.h
index 5eaa2902ed39..67e422590c9a 100644
--- a/drivers/dma/fsl-edma-common.h
+++ b/drivers/dma/fsl-edma-common.h
@@ -147,6 +147,7 @@ struct fsl_edma_drvdata {
 	enum edma_version	version;
 	u32			dmamuxs;
 	bool			has_dmaclk;
+	bool			mux_swap;
 	int			(*setup_irq)(struct platform_device *pdev,
 					     struct fsl_edma_engine *fsl_edma);
 };
diff --git a/drivers/dma/fsl-edma.c b/drivers/dma/fsl-edma.c
index b626c06ac2e0..eff7ebd8cf35 100644
--- a/drivers/dma/fsl-edma.c
+++ b/drivers/dma/fsl-edma.c
@@ -233,6 +233,13 @@ static struct fsl_edma_drvdata vf610_data = {
 	.setup_irq = fsl_edma_irq_init,
 };
 
+static struct fsl_edma_drvdata ls1028a_data = {
+	.version = v1,
+	.dmamuxs = DMAMUX_NR,
+	.mux_swap = true,
+	.setup_irq = fsl_edma_irq_init,
+};
+
 static struct fsl_edma_drvdata imx7ulp_data = {
 	.version = v3,
 	.dmamuxs = 1,
@@ -242,6 +249,7 @@ static struct fsl_edma_drvdata imx7ulp_data = {
 
 static const struct of_device_id fsl_edma_dt_ids[] = {
 	{ .compatible = "fsl,vf610-edma", .data = &vf610_data},
+	{ .compatible = "fsl,ls1028a-edma", .data = &ls1028a_data},
 	{ .compatible = "fsl,imx7ulp-edma", .data = &imx7ulp_data},
 	{ /* sentinel */ }
 };
-- 
2.17.1


WARNING: multiple messages have this Message-ID (diff)
From: Peng Ma <peng.ma@nxp.com>
To: "vkoul@kernel.org" <vkoul@kernel.org>,
	"robh+dt@kernel.org" <robh+dt@kernel.org>,
	"mark.rutland@arm.com" <mark.rutland@arm.com>,
	"shawnguo@kernel.org" <shawnguo@kernel.org>,
	Leo Li <leoyang.li@nxp.com>,
	"dan.j.williams@intel.com" <dan.j.williams@intel.com>,
	Robin Gong <yibin.gong@nxp.com>
Cc: "dmaengine@vger.kernel.org" <dmaengine@vger.kernel.org>,
	"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
	Peng Ma <peng.ma@nxp.com>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	"linux-arm-kernel@lists.infradead.org"
	<linux-arm-kernel@lists.infradead.org>
Subject: [v4 1/2] dmaengine: fsl-edma: Add eDMA support for QorIQ LS1028A platform
Date: Wed, 11 Dec 2019 08:09:33 +0000	[thread overview]
Message-ID: <20191211080749.30751-1-peng.ma@nxp.com> (raw)

Our platforms(such as LS1021A, LS1012A, LS1043A, LS1046A, LS1028A) with
below registers(CHCFG0 - CHCFG15) of eDMA as follows:
*-----------------------------------------------------------*
|     Offset   |	OTHERS      |		LS1028A	    |
|--------------|--------------------|-----------------------|
|     0x0      |        CHCFG0      |           CHCFG3      |
|--------------|--------------------|-----------------------|
|     0x1      |        CHCFG1      |           CHCFG2      |
|--------------|--------------------|-----------------------|
|     0x2      |        CHCFG2      |           CHCFG1      |
|--------------|--------------------|-----------------------|
|     0x3      |        CHCFG3      |           CHCFG0      |
|--------------|--------------------|-----------------------|
|     ...      |        ......      |           ......      |
|--------------|--------------------|-----------------------|
|     0xC      |        CHCFG12     |           CHCFG15     |
|--------------|--------------------|-----------------------|
|     0xD      |        CHCFG13     |           CHCFG14     |
|--------------|--------------------|-----------------------|
|     0xE      |        CHCFG14     |           CHCFG13     |
|--------------|--------------------|-----------------------|
|     0xF      |        CHCFG15     |           CHCFG12     |
*-----------------------------------------------------------*

This patch is to improve edma driver to fit LS1028A platform.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
---
Changed for v4:
	- Add 'mux_swap' into 'struct fsl_edma_drvdata'
	- Remove soc match function  

 drivers/dma/fsl-edma-common.c | 5 +++++
 drivers/dma/fsl-edma-common.h | 1 +
 drivers/dma/fsl-edma.c        | 8 ++++++++
 3 files changed, 14 insertions(+)

diff --git a/drivers/dma/fsl-edma-common.c b/drivers/dma/fsl-edma-common.c
index b1a7ca91701a..5697c3622699 100644
--- a/drivers/dma/fsl-edma-common.c
+++ b/drivers/dma/fsl-edma-common.c
@@ -109,10 +109,15 @@ void fsl_edma_chan_mux(struct fsl_edma_chan *fsl_chan,
 	u32 ch = fsl_chan->vchan.chan.chan_id;
 	void __iomem *muxaddr;
 	unsigned int chans_per_mux, ch_off;
+	int endian_diff[4] = {3, 1, -1, -3};
 	u32 dmamux_nr = fsl_chan->edma->drvdata->dmamuxs;
 
 	chans_per_mux = fsl_chan->edma->n_chans / dmamux_nr;
 	ch_off = fsl_chan->vchan.chan.chan_id % chans_per_mux;
+
+	if (fsl_chan->edma->drvdata->mux_swap)
+		ch_off += endian_diff[ch_off % 4];
+
 	muxaddr = fsl_chan->edma->muxbase[ch / chans_per_mux];
 	slot = EDMAMUX_CHCFG_SOURCE(slot);
 
diff --git a/drivers/dma/fsl-edma-common.h b/drivers/dma/fsl-edma-common.h
index 5eaa2902ed39..67e422590c9a 100644
--- a/drivers/dma/fsl-edma-common.h
+++ b/drivers/dma/fsl-edma-common.h
@@ -147,6 +147,7 @@ struct fsl_edma_drvdata {
 	enum edma_version	version;
 	u32			dmamuxs;
 	bool			has_dmaclk;
+	bool			mux_swap;
 	int			(*setup_irq)(struct platform_device *pdev,
 					     struct fsl_edma_engine *fsl_edma);
 };
diff --git a/drivers/dma/fsl-edma.c b/drivers/dma/fsl-edma.c
index b626c06ac2e0..eff7ebd8cf35 100644
--- a/drivers/dma/fsl-edma.c
+++ b/drivers/dma/fsl-edma.c
@@ -233,6 +233,13 @@ static struct fsl_edma_drvdata vf610_data = {
 	.setup_irq = fsl_edma_irq_init,
 };
 
+static struct fsl_edma_drvdata ls1028a_data = {
+	.version = v1,
+	.dmamuxs = DMAMUX_NR,
+	.mux_swap = true,
+	.setup_irq = fsl_edma_irq_init,
+};
+
 static struct fsl_edma_drvdata imx7ulp_data = {
 	.version = v3,
 	.dmamuxs = 1,
@@ -242,6 +249,7 @@ static struct fsl_edma_drvdata imx7ulp_data = {
 
 static const struct of_device_id fsl_edma_dt_ids[] = {
 	{ .compatible = "fsl,vf610-edma", .data = &vf610_data},
+	{ .compatible = "fsl,ls1028a-edma", .data = &ls1028a_data},
 	{ .compatible = "fsl,imx7ulp-edma", .data = &imx7ulp_data},
 	{ /* sentinel */ }
 };
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2019-12-11  8:09 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-11  8:09 Peng Ma [this message]
2019-12-11  8:09 ` [v4 1/2] dmaengine: fsl-edma: Add eDMA support for QorIQ LS1028A platform Peng Ma
2019-12-11  8:09 ` [v4 2/2] arm64: dts: ls1028a: Update edma compatible to fit eDMA driver Peng Ma
2019-12-11  8:09   ` Peng Ma
2019-12-12  2:19   ` Shawn Guo
2019-12-12  2:19     ` Shawn Guo
2019-12-12  1:56 ` [v4 1/2] dmaengine: fsl-edma: Add eDMA support for QorIQ LS1028A platform Robin Gong
2019-12-12  1:56   ` Robin Gong

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191211080749.30751-1-peng.ma@nxp.com \
    --to=peng.ma@nxp.com \
    --cc=dan.j.williams@intel.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dmaengine@vger.kernel.org \
    --cc=leoyang.li@nxp.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=shawnguo@kernel.org \
    --cc=vkoul@kernel.org \
    --cc=yibin.gong@nxp.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.