All of lore.kernel.org
 help / color / mirror / Atom feed
From: Rob Herring <robh@kernel.org>
To: Roger Quadros <rogerq@ti.com>
Cc: nm@ti.com, devicetree@vger.kernel.org, vigneshr@ti.com,
	nsekhar@ti.com, linux-kernel@vger.kernel.org, kishon@ti.com,
	t-kristo@ti.com, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 2/5] arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select SERDES lane mux
Date: Tue, 14 Jan 2020 19:47:24 -0600	[thread overview]
Message-ID: <20200115014724.GA20772@bogus> (raw)
In-Reply-To: <20200108111830.8482-3-rogerq@ti.com>

On Wed, Jan 08, 2020 at 01:18:27PM +0200, Roger Quadros wrote:
> From: Kishon Vijay Abraham I <kishon@ti.com>
> 
> Add serdes_ln_ctrl node used for selecting SERDES lane mux.
> 
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 26 +++++++++++
>  include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
>  2 files changed, 79 insertions(+)
>  create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> index 24cb78db28e4..6741c1e67f50 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> @@ -5,6 +5,8 @@
>   * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
>   */
>  #include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/mux/mux.h>
> +#include <dt-bindings/mux/mux-j721e-wiz.h>
>  
>  &cbass_main {
>  	msmc_ram: sram@70000000 {
> @@ -19,6 +21,30 @@
>  		};
>  	};
>  
> +	scm_conf: scm_conf@100000 {

Don't use '_' in node names.

> +		compatible = "syscon", "simple-mfd";

Needs a specific compatible especially since the child node doesn't have 
one.

> +		reg = <0 0x00100000 0 0x1c000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0x0 0x0 0x00100000 0x1c000>;
> +
> +		serdes_ln_ctrl: serdes_ln_ctrl@4080 {

'reg' is needed if there's a unit-address. If there's a register range 
with only the mux controls, then add 'reg'.

> +			compatible = "mmio-mux";
> +			#mux-control-cells = <1>;
> +			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
> +					<0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
> +					<0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
> +					<0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
> +					<0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
> +					/* SERDES4 lane0/1/2/3 select */
> +			idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
> +				      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
> +				      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
> +				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
> +				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
> +		};
> +	};
> +
>  	gic500: interrupt-controller@1800000 {
>  		compatible = "arm,gic-v3";
>  		#address-cells = <2>;
> diff --git a/include/dt-bindings/mux/mux-j721e-wiz.h b/include/dt-bindings/mux/mux-j721e-wiz.h
> new file mode 100644
> index 000000000000..fd1c4ea9fc7f
> --- /dev/null
> +++ b/include/dt-bindings/mux/mux-j721e-wiz.h
> @@ -0,0 +1,53 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * This header provides constants for J721E WIZ.
> + */
> +
> +#ifndef _DT_BINDINGS_J721E_WIZ
> +#define _DT_BINDINGS_J721E_WIZ
> +
> +#define SERDES0_LANE0_QSGMII_LANE1	0x0
> +#define SERDES0_LANE0_PCIE0_LANE0	0x1
> +#define SERDES0_LANE0_USB3_0_SWAP	0x2
> +
> +#define SERDES0_LANE1_QSGMII_LANE2	0x0
> +#define SERDES0_LANE1_PCIE0_LANE1	0x1
> +#define SERDES0_LANE1_USB3_0		0x2
> +
> +#define SERDES1_LANE0_QSGMII_LANE3	0x0
> +#define SERDES1_LANE0_PCIE1_LANE0	0x1
> +#define SERDES1_LANE0_USB3_1_SWAP	0x2
> +#define SERDES1_LANE0_SGMII_LANE0	0x3
> +
> +#define SERDES1_LANE1_QSGMII_LANE4	0x0
> +#define SERDES1_LANE1_PCIE1_LANE1	0x1
> +#define SERDES1_LANE1_USB3_1		0x2
> +#define SERDES1_LANE1_SGMII_LANE1	0x3
> +
> +#define SERDES2_LANE0_PCIE2_LANE0	0x1
> +#define SERDES2_LANE0_SGMII_LANE0	0x3
> +#define SERDES2_LANE0_USB3_1_SWAP	0x2
> +
> +#define SERDES2_LANE1_PCIE2_LANE1	0x1
> +#define SERDES2_LANE1_USB3_1		0x2
> +#define SERDES2_LANE1_SGMII_LANE1	0x3
> +
> +#define SERDES3_LANE0_PCIE3_LANE0	0x1
> +#define SERDES3_LANE0_USB3_0_SWAP	0x2
> +
> +#define SERDES3_LANE1_PCIE3_LANE1	0x1
> +#define SERDES3_LANE1_USB3_0		0x2
> +
> +#define SERDES4_LANE0_EDP_LANE0		0x0
> +#define SERDES4_LANE0_QSGMII_LANE5	0x2
> +
> +#define SERDES4_LANE1_EDP_LANE1		0x0
> +#define SERDES4_LANE1_QSGMII_LANE6	0x2
> +
> +#define SERDES4_LANE2_EDP_LANE2		0x0
> +#define SERDES4_LANE2_QSGMII_LANE7	0x2
> +
> +#define SERDES4_LANE3_EDP_LANE3		0x0
> +#define SERDES4_LANE3_QSGMII_LANE8	0x2
> +
> +#endif /* _DT_BINDINGS_J721E_WIZ */
> -- 
> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
> Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

WARNING: multiple messages have this Message-ID (diff)
From: Rob Herring <robh@kernel.org>
To: Roger Quadros <rogerq@ti.com>
Cc: t-kristo@ti.com, nm@ti.com, kishon@ti.com, nsekhar@ti.com,
	vigneshr@ti.com, linux-arm-kernel@lists.infradead.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 2/5] arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select SERDES lane mux
Date: Tue, 14 Jan 2020 19:47:24 -0600	[thread overview]
Message-ID: <20200115014724.GA20772@bogus> (raw)
In-Reply-To: <20200108111830.8482-3-rogerq@ti.com>

On Wed, Jan 08, 2020 at 01:18:27PM +0200, Roger Quadros wrote:
> From: Kishon Vijay Abraham I <kishon@ti.com>
> 
> Add serdes_ln_ctrl node used for selecting SERDES lane mux.
> 
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 26 +++++++++++
>  include/dt-bindings/mux/mux-j721e-wiz.h   | 53 +++++++++++++++++++++++
>  2 files changed, 79 insertions(+)
>  create mode 100644 include/dt-bindings/mux/mux-j721e-wiz.h
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> index 24cb78db28e4..6741c1e67f50 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> @@ -5,6 +5,8 @@
>   * Copyright (C) 2016-2019 Texas Instruments Incorporated - http://www.ti.com/
>   */
>  #include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/mux/mux.h>
> +#include <dt-bindings/mux/mux-j721e-wiz.h>
>  
>  &cbass_main {
>  	msmc_ram: sram@70000000 {
> @@ -19,6 +21,30 @@
>  		};
>  	};
>  
> +	scm_conf: scm_conf@100000 {

Don't use '_' in node names.

> +		compatible = "syscon", "simple-mfd";

Needs a specific compatible especially since the child node doesn't have 
one.

> +		reg = <0 0x00100000 0 0x1c000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0x0 0x0 0x00100000 0x1c000>;
> +
> +		serdes_ln_ctrl: serdes_ln_ctrl@4080 {

'reg' is needed if there's a unit-address. If there's a register range 
with only the mux controls, then add 'reg'.

> +			compatible = "mmio-mux";
> +			#mux-control-cells = <1>;
> +			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
> +					<0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
> +					<0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
> +					<0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
> +					<0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
> +					/* SERDES4 lane0/1/2/3 select */
> +			idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
> +				      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
> +				      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
> +				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
> +				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
> +		};
> +	};
> +
>  	gic500: interrupt-controller@1800000 {
>  		compatible = "arm,gic-v3";
>  		#address-cells = <2>;
> diff --git a/include/dt-bindings/mux/mux-j721e-wiz.h b/include/dt-bindings/mux/mux-j721e-wiz.h
> new file mode 100644
> index 000000000000..fd1c4ea9fc7f
> --- /dev/null
> +++ b/include/dt-bindings/mux/mux-j721e-wiz.h
> @@ -0,0 +1,53 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * This header provides constants for J721E WIZ.
> + */
> +
> +#ifndef _DT_BINDINGS_J721E_WIZ
> +#define _DT_BINDINGS_J721E_WIZ
> +
> +#define SERDES0_LANE0_QSGMII_LANE1	0x0
> +#define SERDES0_LANE0_PCIE0_LANE0	0x1
> +#define SERDES0_LANE0_USB3_0_SWAP	0x2
> +
> +#define SERDES0_LANE1_QSGMII_LANE2	0x0
> +#define SERDES0_LANE1_PCIE0_LANE1	0x1
> +#define SERDES0_LANE1_USB3_0		0x2
> +
> +#define SERDES1_LANE0_QSGMII_LANE3	0x0
> +#define SERDES1_LANE0_PCIE1_LANE0	0x1
> +#define SERDES1_LANE0_USB3_1_SWAP	0x2
> +#define SERDES1_LANE0_SGMII_LANE0	0x3
> +
> +#define SERDES1_LANE1_QSGMII_LANE4	0x0
> +#define SERDES1_LANE1_PCIE1_LANE1	0x1
> +#define SERDES1_LANE1_USB3_1		0x2
> +#define SERDES1_LANE1_SGMII_LANE1	0x3
> +
> +#define SERDES2_LANE0_PCIE2_LANE0	0x1
> +#define SERDES2_LANE0_SGMII_LANE0	0x3
> +#define SERDES2_LANE0_USB3_1_SWAP	0x2
> +
> +#define SERDES2_LANE1_PCIE2_LANE1	0x1
> +#define SERDES2_LANE1_USB3_1		0x2
> +#define SERDES2_LANE1_SGMII_LANE1	0x3
> +
> +#define SERDES3_LANE0_PCIE3_LANE0	0x1
> +#define SERDES3_LANE0_USB3_0_SWAP	0x2
> +
> +#define SERDES3_LANE1_PCIE3_LANE1	0x1
> +#define SERDES3_LANE1_USB3_0		0x2
> +
> +#define SERDES4_LANE0_EDP_LANE0		0x0
> +#define SERDES4_LANE0_QSGMII_LANE5	0x2
> +
> +#define SERDES4_LANE1_EDP_LANE1		0x0
> +#define SERDES4_LANE1_QSGMII_LANE6	0x2
> +
> +#define SERDES4_LANE2_EDP_LANE2		0x0
> +#define SERDES4_LANE2_QSGMII_LANE7	0x2
> +
> +#define SERDES4_LANE3_EDP_LANE3		0x0
> +#define SERDES4_LANE3_QSGMII_LANE8	0x2
> +
> +#endif /* _DT_BINDINGS_J721E_WIZ */
> -- 
> Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
> Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
> 

  reply	other threads:[~2020-01-15  1:47 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-08 11:18 [PATCH 0/5] arm64: ti: k3-j721e: Add SERDES PHY and USB3.0 support Roger Quadros
2020-01-08 11:18 ` Roger Quadros
2020-01-08 11:18 ` [PATCH 1/5] arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes Roger Quadros
2020-01-08 11:18   ` Roger Quadros
2020-01-08 11:18 ` [PATCH 2/5] arm64: dts: ti: k3-j721e-main: Add serdes_ln_ctrl node to select SERDES lane mux Roger Quadros
2020-01-08 11:18   ` Roger Quadros
2020-01-15  1:47   ` Rob Herring [this message]
2020-01-15  1:47     ` Rob Herring
2020-01-21  5:13     ` Kishon Vijay Abraham I
2020-01-21  5:13       ` Kishon Vijay Abraham I
2020-01-21 17:57       ` Rob Herring
2020-01-21 17:57         ` Rob Herring
2020-01-22  5:05         ` Kishon Vijay Abraham I
2020-01-22  5:05           ` Kishon Vijay Abraham I
2020-01-08 11:18 ` [PATCH 3/5] arm64: dts: ti: k3-j721e-main.dtsi: Add USB to SERDES MUX Roger Quadros
2020-01-08 11:18   ` Roger Quadros
2020-01-08 11:18 ` [PATCH 4/5] arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0 Roger Quadros
2020-01-08 11:18   ` Roger Quadros
2020-01-08 11:18 ` [PATCH 5/5] arm64: dts: k3-j721e-proc-board: Add wait time for sampling Type-C DIR line Roger Quadros
2020-01-08 11:18   ` Roger Quadros

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200115014724.GA20772@bogus \
    --to=robh@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kishon@ti.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=nm@ti.com \
    --cc=nsekhar@ti.com \
    --cc=rogerq@ti.com \
    --cc=t-kristo@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.