* [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for RDB board
@ 2020-02-04 4:09 ` Yangbo Lu
0 siblings, 0 replies; 6+ messages in thread
From: Yangbo Lu @ 2020-02-04 4:09 UTC (permalink / raw)
To: linux-arm-kernel, devicetree, linux-kernel, Shawn Guo, Li Yang
Cc: Mark Rutland, Rob Herring, Yangbo Lu
This patch is to add eMMC HS200 speed mode support on ls1088ardb
whose controller and peripheral circut support such capability.
And clocks dts property is needed for driver to get peripheral
clock value used for this speed mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts | 1 +
arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 1 +
2 files changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
index 4d77b34..5633e59 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
@@ -83,6 +83,7 @@
};
&esdhc {
+ mmc-hs200-1_8v;
status = "okay";
};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index 5945662..ec6013a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -393,6 +393,7 @@
reg = <0x0 0x2140000 0x0 0x10000>;
interrupts = <0 28 0x4>; /* Level high type */
clock-frequency = <0>;
+ clocks = <&clockgen 2 1>;
voltage-ranges = <1800 1800 3300 3300>;
sdhci,auto-cmd12;
little-endian;
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for RDB board
@ 2020-02-04 4:09 ` Yangbo Lu
0 siblings, 0 replies; 6+ messages in thread
From: Yangbo Lu @ 2020-02-04 4:09 UTC (permalink / raw)
To: linux-arm-kernel, devicetree, linux-kernel, Shawn Guo, Li Yang
Cc: Rob Herring, Mark Rutland, Yangbo Lu
This patch is to add eMMC HS200 speed mode support on ls1088ardb
whose controller and peripheral circut support such capability.
And clocks dts property is needed for driver to get peripheral
clock value used for this speed mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts | 1 +
arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 1 +
2 files changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
index 4d77b34..5633e59 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
@@ -83,6 +83,7 @@
};
&esdhc {
+ mmc-hs200-1_8v;
status = "okay";
};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index 5945662..ec6013a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -393,6 +393,7 @@
reg = <0x0 0x2140000 0x0 0x10000>;
interrupts = <0 28 0x4>; /* Level high type */
clock-frequency = <0>;
+ clocks = <&clockgen 2 1>;
voltage-ranges = <1800 1800 3300 3300>;
sdhci,auto-cmd12;
little-endian;
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* RE: [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for RDB board
2020-02-04 4:09 ` Yangbo Lu
@ 2020-02-11 5:05 ` Y.b. Lu
-1 siblings, 0 replies; 6+ messages in thread
From: Y.b. Lu @ 2020-02-11 5:05 UTC (permalink / raw)
To: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, Shawn Guo, Leo Li
Cc: Mark Rutland, Rob Herring
Any comments? Thanks!
> -----Original Message-----
> From: Yangbo Lu <yangbo.lu@nxp.com>
> Sent: Tuesday, February 4, 2020 12:09 PM
> To: linux-arm-kernel@lists.infradead.org; devicetree@vger.kernel.org;
> linux-kernel@vger.kernel.org; Shawn Guo <shawnguo@kernel.org>; Leo Li
> <leoyang.li@nxp.com>
> Cc: Rob Herring <robh+dt@kernel.org>; Mark Rutland
> <mark.rutland@arm.com>; Y.b. Lu <yangbo.lu@nxp.com>
> Subject: [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for
> RDB board
>
> This patch is to add eMMC HS200 speed mode support on ls1088ardb
> whose controller and peripheral circut support such capability.
> And clocks dts property is needed for driver to get peripheral
> clock value used for this speed mode.
>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts | 1 +
> arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 1 +
> 2 files changed, 2 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
> b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
> index 4d77b34..5633e59 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
> @@ -83,6 +83,7 @@
> };
>
> &esdhc {
> + mmc-hs200-1_8v;
> status = "okay";
> };
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> index 5945662..ec6013a 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> @@ -393,6 +393,7 @@
> reg = <0x0 0x2140000 0x0 0x10000>;
> interrupts = <0 28 0x4>; /* Level high type */
> clock-frequency = <0>;
> + clocks = <&clockgen 2 1>;
> voltage-ranges = <1800 1800 3300 3300>;
> sdhci,auto-cmd12;
> little-endian;
> --
> 2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for RDB board
@ 2020-02-11 5:05 ` Y.b. Lu
0 siblings, 0 replies; 6+ messages in thread
From: Y.b. Lu @ 2020-02-11 5:05 UTC (permalink / raw)
To: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, Shawn Guo, Leo Li
Cc: Rob Herring, Mark Rutland
Any comments? Thanks!
> -----Original Message-----
> From: Yangbo Lu <yangbo.lu@nxp.com>
> Sent: Tuesday, February 4, 2020 12:09 PM
> To: linux-arm-kernel@lists.infradead.org; devicetree@vger.kernel.org;
> linux-kernel@vger.kernel.org; Shawn Guo <shawnguo@kernel.org>; Leo Li
> <leoyang.li@nxp.com>
> Cc: Rob Herring <robh+dt@kernel.org>; Mark Rutland
> <mark.rutland@arm.com>; Y.b. Lu <yangbo.lu@nxp.com>
> Subject: [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for
> RDB board
>
> This patch is to add eMMC HS200 speed mode support on ls1088ardb
> whose controller and peripheral circut support such capability.
> And clocks dts property is needed for driver to get peripheral
> clock value used for this speed mode.
>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts | 1 +
> arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 1 +
> 2 files changed, 2 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
> b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
> index 4d77b34..5633e59 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
> @@ -83,6 +83,7 @@
> };
>
> &esdhc {
> + mmc-hs200-1_8v;
> status = "okay";
> };
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> index 5945662..ec6013a 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> @@ -393,6 +393,7 @@
> reg = <0x0 0x2140000 0x0 0x10000>;
> interrupts = <0 28 0x4>; /* Level high type */
> clock-frequency = <0>;
> + clocks = <&clockgen 2 1>;
> voltage-ranges = <1800 1800 3300 3300>;
> sdhci,auto-cmd12;
> little-endian;
> --
> 2.7.4
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for RDB board
2020-02-04 4:09 ` Yangbo Lu
@ 2020-02-14 3:40 ` Shawn Guo
-1 siblings, 0 replies; 6+ messages in thread
From: Shawn Guo @ 2020-02-14 3:40 UTC (permalink / raw)
To: Yangbo Lu
Cc: Mark Rutland, devicetree, linux-kernel, Li Yang, Rob Herring,
linux-arm-kernel
On Tue, Feb 04, 2020 at 12:09:28PM +0800, Yangbo Lu wrote:
> This patch is to add eMMC HS200 speed mode support on ls1088ardb
> whose controller and peripheral circut support such capability.
> And clocks dts property is needed for driver to get peripheral
> clock value used for this speed mode.
>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Applied, thanks.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for RDB board
@ 2020-02-14 3:40 ` Shawn Guo
0 siblings, 0 replies; 6+ messages in thread
From: Shawn Guo @ 2020-02-14 3:40 UTC (permalink / raw)
To: Yangbo Lu
Cc: linux-arm-kernel, devicetree, linux-kernel, Li Yang, Rob Herring,
Mark Rutland
On Tue, Feb 04, 2020 at 12:09:28PM +0800, Yangbo Lu wrote:
> This patch is to add eMMC HS200 speed mode support on ls1088ardb
> whose controller and peripheral circut support such capability.
> And clocks dts property is needed for driver to get peripheral
> clock value used for this speed mode.
>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Applied, thanks.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-02-14 3:40 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2020-02-04 4:09 [PATCH] arm64: dts: ls1088a: support eMMC HS200 speed mode for RDB board Yangbo Lu
2020-02-04 4:09 ` Yangbo Lu
2020-02-11 5:05 ` Y.b. Lu
2020-02-11 5:05 ` Y.b. Lu
2020-02-14 3:40 ` Shawn Guo
2020-02-14 3:40 ` Shawn Guo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.