From: Rob Herring <robh@kernel.org>
To: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>,
Ralf Baechle <ralf@linux-mips.org>,
Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>,
linux-kernel@vger.kernel.org, Mark Brown <broonie@kernel.org>,
Paul Burton <paulburton@kernel.org>,
Arnd Bergmann <arnd@arndb.de>,
linux-spi@vger.kernel.org,
Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>,
linux-mips@vger.kernel.org, devicetree@vger.kernel.org,
Thomas Bogendoerfer <tsbogend@alpha.franken.de>,
Serge Semin <fancer.lancer@gmail.com>,
Rob Herring <robh+dt@kernel.org>,
Gareth Williams <gareth.williams.jx@renesas.com>,
Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Subject: Re: [PATCH v4 16/16] dt-bindings: spi: Convert DW SPI binding to DT schema
Date: Thu, 28 May 2020 17:28:10 -0600 [thread overview]
Message-ID: <20200528232810.GA875356@bogus> (raw)
In-Reply-To: <20200522000806.7381-17-Sergey.Semin@baikalelectronics.ru>
On Fri, 22 May 2020 03:08:05 +0300, Serge Semin wrote:
> Modern device tree bindings are supposed to be created as YAML-files
> in accordance with dt-schema. This commit replaces two DW SPI legacy
> bare text bindings with YAML file. As before the bindings file states
> that the corresponding dts node is supposed to be compatible either
> with generic DW APB SSI controller or with Microsemi/Amazon/Renesas/Intel
> vendors-specific controllers, to have registers, interrupts and clocks
> properties. Though in case of Microsemi version of the controller
> there must be two registers resources specified. Properties like
> clock-names, reg-io-width, cs-gpio, num-cs, DMA and slave device
> sub-nodes are optional.
>
> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
> Cc: Paul Burton <paulburton@kernel.org>
> Cc: Ralf Baechle <ralf@linux-mips.org>
> Cc: Arnd Bergmann <arnd@arndb.de>
> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> Cc: linux-mips@vger.kernel.org
> ---
> .../bindings/spi/snps,dw-apb-ssi.txt | 44 ------
> .../bindings/spi/snps,dw-apb-ssi.yaml | 127 ++++++++++++++++++
> .../devicetree/bindings/spi/spi-dw.txt | 24 ----
> 3 files changed, 127 insertions(+), 68 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
> create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
> delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
>
Reviewed-by: Rob Herring <robh@kernel.org>
next prev parent reply other threads:[~2020-05-28 23:57 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-22 0:07 [PATCH v4 00/16] spi: dw: Add generic DW DMA controller support Serge Semin
2020-05-22 0:07 ` [PATCH v4 02/16] spi: dw: Enable interrupts in accordance with DMA xfer mode Serge Semin
2020-05-22 0:07 ` [PATCH v4 04/16] spi: dw: Discard unused void priv pointer Serge Semin
2020-05-22 0:07 ` [PATCH v4 06/16] spi: dw: Parameterize the DMA Rx/Tx burst length Serge Semin
2020-05-22 11:06 ` Andy Shevchenko
2020-05-22 0:07 ` [PATCH v4 07/16] spi: dw: Use DMA max burst to set the request thresholds Serge Semin
2020-05-22 0:08 ` [PATCH v4 11/16] spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI Serge Semin
2020-05-22 0:08 ` [PATCH v4 12/16] spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core Serge Semin
2020-05-22 11:07 ` Andy Shevchenko
2020-05-22 11:08 ` Andy Shevchenko
2020-05-22 0:08 ` [PATCH v4 14/16] spi: dw: Add DMA support to the DW SPI MMIO driver Serge Semin
2020-05-22 0:08 ` [PATCH v4 16/16] dt-bindings: spi: Convert DW SPI binding to DT schema Serge Semin
2020-05-28 23:28 ` Rob Herring [this message]
[not found] ` <20200522000806.7381-2-Sergey.Semin@baikalelectronics.ru>
2020-05-22 11:13 ` [PATCH v4 01/16] spi: dw: Add Tx/Rx finish wait methods to the MID DMA Andy Shevchenko
[not found] ` <20200522115235.rt3ay7lveimrgooa@mobilestation>
2020-05-22 12:10 ` Mark Brown
2020-05-22 12:12 ` Andy Shevchenko
2020-05-22 12:18 ` Mark Brown
2020-05-22 12:34 ` Andy Shevchenko
[not found] ` <20200522124406.co7gmteojfsooerc@mobilestation>
[not found] ` <20200522131013.GH5801@sirena.org.uk>
[not found] ` <20200522132742.taf2ixfjpyd5u3dt@mobilestation>
[not found] ` <20200522140025.bmd6bhpjjk5msvsm@mobilestation>
2020-05-22 14:36 ` Andy Shevchenko
[not found] ` <20200522144542.brhibh453wid2d6v@mobilestation>
2020-05-22 15:22 ` Mark Brown
2020-05-23 8:34 ` Serge Semin
2020-05-25 11:41 ` Mark Brown
2020-05-25 21:36 ` Serge Semin
2020-05-22 11:22 ` [PATCH v4 00/16] spi: dw: Add generic DW DMA controller support Andy Shevchenko
2020-05-22 11:23 ` Andy Shevchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200528232810.GA875356@bogus \
--to=robh@kernel.org \
--cc=Alexey.Malahov@baikalelectronics.ru \
--cc=Georgy.Vlasov@baikalelectronics.ru \
--cc=Ramil.Zaripov@baikalelectronics.ru \
--cc=Sergey.Semin@baikalelectronics.ru \
--cc=andriy.shevchenko@linux.intel.com \
--cc=arnd@arndb.de \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=fancer.lancer@gmail.com \
--cc=gareth.williams.jx@renesas.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=paulburton@kernel.org \
--cc=ralf@linux-mips.org \
--cc=robh+dt@kernel.org \
--cc=tsbogend@alpha.franken.de \
--cc=wan.ahmad.zainie.wan.mohamad@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.