* [PATCH v2] serial: samsung: Re-factors UART IRQ resource for various Samsung SoC [not found] <CGME20200628071932epcas5p175059c085421a95de76202767bd132cf@epcas5p1.samsung.com> @ 2020-06-28 7:00 ` Tamseel Shams 0 siblings, 0 replies; 6+ messages in thread From: Tamseel Shams @ 2020-06-28 7:00 UTC (permalink / raw) To: kgene, krzk, gregkh, jslaby Cc: linux-arm-kernel, linux-samsung-soc, linux-serial, linux-kernel, alim.akhtar, Tamseel Shams In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP is having 2 interrupt lines. However, in other SoCs like s3c6400, s5pv210, exynos5433, and exynos4210 UART is having only 1 interrupt line. Due to this, "platform_get_irq(platdev, 1)" call in the driver gives the following warning: "IRQ index 1 not found" on recent platforms. This patch re-factors the IRQ resources handling for each platform and hence fixing the above warnings seen on some platforms. Signed-off-by: Tamseel Shams <m.shams@samsung.com> --- Removed the RFC tag and using 'platform_get_irq_optional' instead of 'platform_get_irq' as per comment received from Robin Murphy. drivers/tty/serial/samsung_tty.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c index 6ef614d8648c..60554f42e208 100644 --- a/drivers/tty/serial/samsung_tty.c +++ b/drivers/tty/serial/samsung_tty.c @@ -60,6 +60,7 @@ struct s3c24xx_uart_info { char *name; unsigned int type; unsigned int fifosize; + unsigned int irq_cnt; unsigned long rx_fifomask; unsigned long rx_fifoshift; unsigned long rx_fifofull; @@ -1908,10 +1909,13 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport, else { port->irq = ret; ourport->rx_irq = ret; - ourport->tx_irq = ret + 1; + if (ourport->info->irq_cnt == 1) + ourport->tx_irq = ret; + else + ourport->tx_irq = ret + 1; } - ret = platform_get_irq(platdev, 1); + ret = platform_get_irq_optional(platdev, 1); if (ret > 0) ourport->tx_irq = ret; /* @@ -2387,6 +2391,7 @@ static struct s3c24xx_serial_drv_data s3c2410_serial_drv_data = { .name = "Samsung S3C2410 UART", .type = PORT_S3C2410, .fifosize = 16, + .irq_cnt = 2, .rx_fifomask = S3C2410_UFSTAT_RXMASK, .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT, .rx_fifofull = S3C2410_UFSTAT_RXFULL, @@ -2414,6 +2419,7 @@ static struct s3c24xx_serial_drv_data s3c2412_serial_drv_data = { .name = "Samsung S3C2412 UART", .type = PORT_S3C2412, .fifosize = 64, + .irq_cnt = 2, .has_divslot = 1, .rx_fifomask = S3C2440_UFSTAT_RXMASK, .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, @@ -2443,6 +2449,7 @@ static struct s3c24xx_serial_drv_data s3c2440_serial_drv_data = { .name = "Samsung S3C2440 UART", .type = PORT_S3C2440, .fifosize = 64, + .irq_cnt = 2, .has_divslot = 1, .rx_fifomask = S3C2440_UFSTAT_RXMASK, .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, @@ -2471,6 +2478,7 @@ static struct s3c24xx_serial_drv_data s3c6400_serial_drv_data = { .name = "Samsung S3C6400 UART", .type = PORT_S3C6400, .fifosize = 64, + .irq_cnt = 1, .has_divslot = 1, .rx_fifomask = S3C2440_UFSTAT_RXMASK, .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, @@ -2498,6 +2506,7 @@ static struct s3c24xx_serial_drv_data s5pv210_serial_drv_data = { .info = &(struct s3c24xx_uart_info) { .name = "Samsung S5PV210 UART", .type = PORT_S3C6400, + .irq_cnt = 1, .has_divslot = 1, .rx_fifomask = S5PV210_UFSTAT_RXMASK, .rx_fifoshift = S5PV210_UFSTAT_RXSHIFT, @@ -2526,6 +2535,7 @@ static struct s3c24xx_serial_drv_data s5pv210_serial_drv_data = { .info = &(struct s3c24xx_uart_info) { \ .name = "Samsung Exynos UART", \ .type = PORT_S3C6400, \ + .irq_cnt = 1, \ .has_divslot = 1, \ .rx_fifomask = S5PV210_UFSTAT_RXMASK, \ .rx_fifoshift = S5PV210_UFSTAT_RXSHIFT, \ -- 2.17.1 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2] serial: samsung: Re-factors UART IRQ resource for various Samsung SoC @ 2020-06-28 7:00 ` Tamseel Shams 0 siblings, 0 replies; 6+ messages in thread From: Tamseel Shams @ 2020-06-28 7:00 UTC (permalink / raw) To: kgene, krzk, gregkh, jslaby Cc: linux-samsung-soc, linux-serial, linux-kernel, alim.akhtar, Tamseel Shams, linux-arm-kernel In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP is having 2 interrupt lines. However, in other SoCs like s3c6400, s5pv210, exynos5433, and exynos4210 UART is having only 1 interrupt line. Due to this, "platform_get_irq(platdev, 1)" call in the driver gives the following warning: "IRQ index 1 not found" on recent platforms. This patch re-factors the IRQ resources handling for each platform and hence fixing the above warnings seen on some platforms. Signed-off-by: Tamseel Shams <m.shams@samsung.com> --- Removed the RFC tag and using 'platform_get_irq_optional' instead of 'platform_get_irq' as per comment received from Robin Murphy. drivers/tty/serial/samsung_tty.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-) diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c index 6ef614d8648c..60554f42e208 100644 --- a/drivers/tty/serial/samsung_tty.c +++ b/drivers/tty/serial/samsung_tty.c @@ -60,6 +60,7 @@ struct s3c24xx_uart_info { char *name; unsigned int type; unsigned int fifosize; + unsigned int irq_cnt; unsigned long rx_fifomask; unsigned long rx_fifoshift; unsigned long rx_fifofull; @@ -1908,10 +1909,13 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport, else { port->irq = ret; ourport->rx_irq = ret; - ourport->tx_irq = ret + 1; + if (ourport->info->irq_cnt == 1) + ourport->tx_irq = ret; + else + ourport->tx_irq = ret + 1; } - ret = platform_get_irq(platdev, 1); + ret = platform_get_irq_optional(platdev, 1); if (ret > 0) ourport->tx_irq = ret; /* @@ -2387,6 +2391,7 @@ static struct s3c24xx_serial_drv_data s3c2410_serial_drv_data = { .name = "Samsung S3C2410 UART", .type = PORT_S3C2410, .fifosize = 16, + .irq_cnt = 2, .rx_fifomask = S3C2410_UFSTAT_RXMASK, .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT, .rx_fifofull = S3C2410_UFSTAT_RXFULL, @@ -2414,6 +2419,7 @@ static struct s3c24xx_serial_drv_data s3c2412_serial_drv_data = { .name = "Samsung S3C2412 UART", .type = PORT_S3C2412, .fifosize = 64, + .irq_cnt = 2, .has_divslot = 1, .rx_fifomask = S3C2440_UFSTAT_RXMASK, .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, @@ -2443,6 +2449,7 @@ static struct s3c24xx_serial_drv_data s3c2440_serial_drv_data = { .name = "Samsung S3C2440 UART", .type = PORT_S3C2440, .fifosize = 64, + .irq_cnt = 2, .has_divslot = 1, .rx_fifomask = S3C2440_UFSTAT_RXMASK, .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, @@ -2471,6 +2478,7 @@ static struct s3c24xx_serial_drv_data s3c6400_serial_drv_data = { .name = "Samsung S3C6400 UART", .type = PORT_S3C6400, .fifosize = 64, + .irq_cnt = 1, .has_divslot = 1, .rx_fifomask = S3C2440_UFSTAT_RXMASK, .rx_fifoshift = S3C2440_UFSTAT_RXSHIFT, @@ -2498,6 +2506,7 @@ static struct s3c24xx_serial_drv_data s5pv210_serial_drv_data = { .info = &(struct s3c24xx_uart_info) { .name = "Samsung S5PV210 UART", .type = PORT_S3C6400, + .irq_cnt = 1, .has_divslot = 1, .rx_fifomask = S5PV210_UFSTAT_RXMASK, .rx_fifoshift = S5PV210_UFSTAT_RXSHIFT, @@ -2526,6 +2535,7 @@ static struct s3c24xx_serial_drv_data s5pv210_serial_drv_data = { .info = &(struct s3c24xx_uart_info) { \ .name = "Samsung Exynos UART", \ .type = PORT_S3C6400, \ + .irq_cnt = 1, \ .has_divslot = 1, \ .rx_fifomask = S5PV210_UFSTAT_RXMASK, \ .rx_fifoshift = S5PV210_UFSTAT_RXSHIFT, \ -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v2] serial: samsung: Re-factors UART IRQ resource for various Samsung SoC 2020-06-28 7:00 ` Tamseel Shams @ 2020-06-29 8:35 ` Krzysztof Kozlowski -1 siblings, 0 replies; 6+ messages in thread From: Krzysztof Kozlowski @ 2020-06-29 8:35 UTC (permalink / raw) To: Tamseel Shams Cc: kgene, gregkh, jslaby, linux-arm-kernel, linux-samsung-soc, linux-serial, linux-kernel, alim.akhtar On Sun, Jun 28, 2020 at 12:30:07PM +0530, Tamseel Shams wrote: > In few older Samsung SoCs like s3c2410, s3c2412 > and s3c2440, UART IP is having 2 interrupt lines. > However, in other SoCs like s3c6400, s5pv210, > exynos5433, and exynos4210 UART is having only 1 > interrupt line. Due to this, "platform_get_irq(platdev, 1)" > call in the driver gives the following warning: > "IRQ index 1 not found" on recent platforms. > > This patch re-factors the IRQ resources handling for > each platform and hence fixing the above warnings seen > on some platforms. > > Signed-off-by: Tamseel Shams <m.shams@samsung.com> > --- > Removed the RFC tag and using 'platform_get_irq_optional' > instead of 'platform_get_irq' as per comment received from > Robin Murphy. > > drivers/tty/serial/samsung_tty.c | 14 ++++++++++++-- > 1 file changed, 12 insertions(+), 2 deletions(-) > > diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c > index 6ef614d8648c..60554f42e208 100644 > --- a/drivers/tty/serial/samsung_tty.c > +++ b/drivers/tty/serial/samsung_tty.c > @@ -60,6 +60,7 @@ struct s3c24xx_uart_info { > char *name; > unsigned int type; > unsigned int fifosize; > + unsigned int irq_cnt; No, it's duplicating the logic. The driver already checks whether SoC has two or one interrupt line with s3c24xx_serial_has_interrupt_mask() so there is no point to have two of such methods. Instead unify it please. Probably entire s3c24xx_serial_has_interrupt_mask() and s3c24xx_serial_type() should be removed and switched into *serial_drv_data. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2] serial: samsung: Re-factors UART IRQ resource for various Samsung SoC @ 2020-06-29 8:35 ` Krzysztof Kozlowski 0 siblings, 0 replies; 6+ messages in thread From: Krzysztof Kozlowski @ 2020-06-29 8:35 UTC (permalink / raw) To: Tamseel Shams Cc: linux-samsung-soc, alim.akhtar, gregkh, linux-kernel, kgene, linux-serial, jslaby, linux-arm-kernel On Sun, Jun 28, 2020 at 12:30:07PM +0530, Tamseel Shams wrote: > In few older Samsung SoCs like s3c2410, s3c2412 > and s3c2440, UART IP is having 2 interrupt lines. > However, in other SoCs like s3c6400, s5pv210, > exynos5433, and exynos4210 UART is having only 1 > interrupt line. Due to this, "platform_get_irq(platdev, 1)" > call in the driver gives the following warning: > "IRQ index 1 not found" on recent platforms. > > This patch re-factors the IRQ resources handling for > each platform and hence fixing the above warnings seen > on some platforms. > > Signed-off-by: Tamseel Shams <m.shams@samsung.com> > --- > Removed the RFC tag and using 'platform_get_irq_optional' > instead of 'platform_get_irq' as per comment received from > Robin Murphy. > > drivers/tty/serial/samsung_tty.c | 14 ++++++++++++-- > 1 file changed, 12 insertions(+), 2 deletions(-) > > diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c > index 6ef614d8648c..60554f42e208 100644 > --- a/drivers/tty/serial/samsung_tty.c > +++ b/drivers/tty/serial/samsung_tty.c > @@ -60,6 +60,7 @@ struct s3c24xx_uart_info { > char *name; > unsigned int type; > unsigned int fifosize; > + unsigned int irq_cnt; No, it's duplicating the logic. The driver already checks whether SoC has two or one interrupt line with s3c24xx_serial_has_interrupt_mask() so there is no point to have two of such methods. Instead unify it please. Probably entire s3c24xx_serial_has_interrupt_mask() and s3c24xx_serial_type() should be removed and switched into *serial_drv_data. Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: [PATCH v2] serial: samsung: Re-factors UART IRQ resource for various Samsung SoC 2020-06-29 8:35 ` Krzysztof Kozlowski @ 2020-07-04 14:25 ` M Tamseel Shams -1 siblings, 0 replies; 6+ messages in thread From: M Tamseel Shams @ 2020-07-04 14:25 UTC (permalink / raw) To: 'Krzysztof Kozlowski' Cc: kgene, gregkh, jslaby, linux-arm-kernel, linux-samsung-soc, linux-serial, linux-kernel, alim.akhtar > On Sun, Jun 28, 2020 at 12:30:07PM +0530, Tamseel Shams wrote: > > In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP > > is having 2 interrupt lines. > > However, in other SoCs like s3c6400, s5pv210, exynos5433, and > > exynos4210 UART is having only 1 interrupt line. Due to this, > > "platform_get_irq(platdev, 1)" > > call in the driver gives the following warning: > > "IRQ index 1 not found" on recent platforms. > > > > This patch re-factors the IRQ resources handling for each platform and > > hence fixing the above warnings seen on some platforms. > > > > Signed-off-by: Tamseel Shams <m.shams@samsung.com> > > --- > > Removed the RFC tag and using 'platform_get_irq_optional' > > instead of 'platform_get_irq' as per comment received from Robin > > Murphy. > > > > drivers/tty/serial/samsung_tty.c | 14 ++++++++++++-- > > 1 file changed, 12 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/tty/serial/samsung_tty.c > > b/drivers/tty/serial/samsung_tty.c > > index 6ef614d8648c..60554f42e208 100644 > > --- a/drivers/tty/serial/samsung_tty.c > > +++ b/drivers/tty/serial/samsung_tty.c > > @@ -60,6 +60,7 @@ struct s3c24xx_uart_info { > > char *name; > > unsigned int type; > > unsigned int fifosize; > > + unsigned int irq_cnt; > > No, it's duplicating the logic. > > The driver already checks whether SoC has two or one interrupt line with > s3c24xx_serial_has_interrupt_mask() so there is no point to have two of such > methods. > > Instead unify it please. Probably entire > s3c24xx_serial_has_interrupt_mask() and s3c24xx_serial_type() should be > removed and switched into *serial_drv_data. > > Best regards, > Krzysztof Hi Krzysztof, Thanks for letting me know about duplication of logic. I will remove my logic of checking of number of interrupt line and replace it with check using s3c24xx_serial_has_interrupt_mask(). I will come up with another patch regarding the suggestion of removal of the two functions s3c24xx_serial_has_interrupt_mask() and s3c24xx_serial_type() and moving it to *serial_drv_data. Thanks & Regards, Tamseel ^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: [PATCH v2] serial: samsung: Re-factors UART IRQ resource for various Samsung SoC @ 2020-07-04 14:25 ` M Tamseel Shams 0 siblings, 0 replies; 6+ messages in thread From: M Tamseel Shams @ 2020-07-04 14:25 UTC (permalink / raw) To: 'Krzysztof Kozlowski' Cc: linux-samsung-soc, alim.akhtar, gregkh, linux-kernel, kgene, linux-serial, jslaby, linux-arm-kernel > On Sun, Jun 28, 2020 at 12:30:07PM +0530, Tamseel Shams wrote: > > In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP > > is having 2 interrupt lines. > > However, in other SoCs like s3c6400, s5pv210, exynos5433, and > > exynos4210 UART is having only 1 interrupt line. Due to this, > > "platform_get_irq(platdev, 1)" > > call in the driver gives the following warning: > > "IRQ index 1 not found" on recent platforms. > > > > This patch re-factors the IRQ resources handling for each platform and > > hence fixing the above warnings seen on some platforms. > > > > Signed-off-by: Tamseel Shams <m.shams@samsung.com> > > --- > > Removed the RFC tag and using 'platform_get_irq_optional' > > instead of 'platform_get_irq' as per comment received from Robin > > Murphy. > > > > drivers/tty/serial/samsung_tty.c | 14 ++++++++++++-- > > 1 file changed, 12 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/tty/serial/samsung_tty.c > > b/drivers/tty/serial/samsung_tty.c > > index 6ef614d8648c..60554f42e208 100644 > > --- a/drivers/tty/serial/samsung_tty.c > > +++ b/drivers/tty/serial/samsung_tty.c > > @@ -60,6 +60,7 @@ struct s3c24xx_uart_info { > > char *name; > > unsigned int type; > > unsigned int fifosize; > > + unsigned int irq_cnt; > > No, it's duplicating the logic. > > The driver already checks whether SoC has two or one interrupt line with > s3c24xx_serial_has_interrupt_mask() so there is no point to have two of such > methods. > > Instead unify it please. Probably entire > s3c24xx_serial_has_interrupt_mask() and s3c24xx_serial_type() should be > removed and switched into *serial_drv_data. > > Best regards, > Krzysztof Hi Krzysztof, Thanks for letting me know about duplication of logic. I will remove my logic of checking of number of interrupt line and replace it with check using s3c24xx_serial_has_interrupt_mask(). I will come up with another patch regarding the suggestion of removal of the two functions s3c24xx_serial_has_interrupt_mask() and s3c24xx_serial_type() and moving it to *serial_drv_data. Thanks & Regards, Tamseel _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-07-04 14:28 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <CGME20200628071932epcas5p175059c085421a95de76202767bd132cf@epcas5p1.samsung.com>
2020-06-28 7:00 ` [PATCH v2] serial: samsung: Re-factors UART IRQ resource for various Samsung SoC Tamseel Shams
2020-06-28 7:00 ` Tamseel Shams
2020-06-29 8:35 ` Krzysztof Kozlowski
2020-06-29 8:35 ` Krzysztof Kozlowski
2020-07-04 14:25 ` M Tamseel Shams
2020-07-04 14:25 ` M Tamseel Shams
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.