From: Rob Herring <robh@kernel.org>
To: Robin Gong <yibin.gong@nxp.com>
Cc: will@kernel.org, festevam@gmail.com, vkoul@kernel.org,
dan.j.williams@intel.com, kernel@pengutronix.de,
catalin.marinas@arm.com, robh+dt@kernel.org, linux-imx@nxp.com,
dmaengine@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, shawnguo@kernel.org,
s.hauer@pengutronix.de, angelo@sysam.it,
devicetree@vger.kernel.org
Subject: Re: [PATCH v1 6/9] dt-bindings: dma: add fsl-edma3 yaml
Date: Thu, 2 Jul 2020 15:01:07 -0600 [thread overview]
Message-ID: <20200702210107.GA1686199@bogus> (raw)
In-Reply-To: <1593702489-21648-7-git-send-email-yibin.gong@nxp.com>
On Thu, 02 Jul 2020 23:08:06 +0800, Robin Gong wrote:
> Add device binding doc for fsl-edma3 driver.
>
> Signed-off-by: Robin Gong <yibin.gong@nxp.com>
> ---
> .../devicetree/bindings/dma/nxp,fsl-edma3.yaml | 129 +++++++++++++++++++++
> 1 file changed, 129 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/dma/nxp,fsl-edma3.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: 'power-domain-names' does not match any of the regexes: 'pinctrl-[0-9]+'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: interrupt-names:1: 'edma2-chan9-tx' does not match '^edma[0-2]-chan[0-31]-tx|rx+$'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: interrupt-names:3: 'edma2-chan11-tx' does not match '^edma[0-2]-chan[0-31]-tx|rx+$'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: interrupt-names:5: 'edma2-chan13-tx' does not match '^edma[0-2]-chan[0-31]-tx|rx+$'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: interrupt-names:7: 'edma2-chan15-tx' does not match '^edma[0-2]-chan[0-31]-tx|rx+$'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: reg: [[1512570880, 65536], [1512636416, 65536], [1512701952, 65536], [1512767488, 65536], [1512833024, 65536], [1512898560, 65536], [1512964096, 65536], [1513029632, 65536]] is too long
See https://patchwork.ozlabs.org/patch/1321003
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
WARNING: multiple messages have this Message-ID (diff)
From: Rob Herring <robh@kernel.org>
To: Robin Gong <yibin.gong@nxp.com>
Cc: devicetree@vger.kernel.org, angelo@sysam.it, will@kernel.org,
s.hauer@pengutronix.de, linux-kernel@vger.kernel.org,
vkoul@kernel.org, robh+dt@kernel.org, linux-imx@nxp.com,
kernel@pengutronix.de, catalin.marinas@arm.com,
dmaengine@vger.kernel.org, shawnguo@kernel.org,
dan.j.williams@intel.com, festevam@gmail.com,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v1 6/9] dt-bindings: dma: add fsl-edma3 yaml
Date: Thu, 2 Jul 2020 15:01:07 -0600 [thread overview]
Message-ID: <20200702210107.GA1686199@bogus> (raw)
In-Reply-To: <1593702489-21648-7-git-send-email-yibin.gong@nxp.com>
On Thu, 02 Jul 2020 23:08:06 +0800, Robin Gong wrote:
> Add device binding doc for fsl-edma3 driver.
>
> Signed-off-by: Robin Gong <yibin.gong@nxp.com>
> ---
> .../devicetree/bindings/dma/nxp,fsl-edma3.yaml | 129 +++++++++++++++++++++
> 1 file changed, 129 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/dma/nxp,fsl-edma3.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: 'power-domain-names' does not match any of the regexes: 'pinctrl-[0-9]+'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: interrupt-names:1: 'edma2-chan9-tx' does not match '^edma[0-2]-chan[0-31]-tx|rx+$'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: interrupt-names:3: 'edma2-chan11-tx' does not match '^edma[0-2]-chan[0-31]-tx|rx+$'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: interrupt-names:5: 'edma2-chan13-tx' does not match '^edma[0-2]-chan[0-31]-tx|rx+$'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: interrupt-names:7: 'edma2-chan15-tx' does not match '^edma[0-2]-chan[0-31]-tx|rx+$'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/dma/nxp,fsl-edma3.example.dt.yaml: dma-controller@5a1f0000: reg: [[1512570880, 65536], [1512636416, 65536], [1512701952, 65536], [1512767488, 65536], [1512833024, 65536], [1512898560, 65536], [1512964096, 65536], [1513029632, 65536]] is too long
See https://patchwork.ozlabs.org/patch/1321003
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-07-02 21:01 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-02 15:08 [PATCH v1 0/9] add fsl-edma3 support Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 1/9] dmaengine: fsl-edma: move edma_request functions into drvdata Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 2/9] dmaengine: fsl-edma-common: add condition check for fsl_edma_chan_mux Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 3/9] dmaengine: fsl-edma-common: add fsl_chan into fsl_edma_fill_tcd Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 4/9] dmaengine: fsl-edma-common: export fsl_edma_set_tcd_regs Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 5/9] dmaengine: fsl-edma3: add fsl-edma3 driver Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 6/9] dt-bindings: dma: add fsl-edma3 yaml Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 21:01 ` Rob Herring [this message]
2020-07-02 21:01 ` Rob Herring
2020-07-03 6:47 ` Robin Gong
2020-07-03 6:47 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 7/9] firmware: imx: scu-pd: correct dma resource Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 8/9] arm64: dts: imx8qxp: add edma2 Robin Gong
2020-07-02 15:08 ` Robin Gong
2020-07-02 15:08 ` [PATCH v1 9/9] arm64: configs: defconfig: add CONFIG_FSL_EDMA3 Robin Gong
2020-07-02 15:08 ` Robin Gong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200702210107.GA1686199@bogus \
--to=robh@kernel.org \
--cc=angelo@sysam.it \
--cc=catalin.marinas@arm.com \
--cc=dan.j.williams@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=vkoul@kernel.org \
--cc=will@kernel.org \
--cc=yibin.gong@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.