Re: [PATCH v2] arch: arm: imx6qdl-icore: Fix OTG_ID pin and sdcard detect

From: Shawn Guo <shawnguo@kernel.org>
To: Suniel Mahesh <sunil@amarulasolutions.com>
Cc: sashal@kernel.org, devicetree@vger.kernel.org,
	gregkh@linuxfoundation.org, s.hauer@pengutronix.de,
	linux-kernel@vger.kernel.org, robh+dt@kernel.org,
	linux-imx@nxp.com, kernel@pengutronix.de,
	Michael Trimarchi <michael@amarulasolutions.com>,
	festevam@gmail.com, linux-amarula@amarulasolutions.com,
	linux-arm-kernel@lists.infradead.org, jagan@amarulasolutions.com
Subject: Re: [PATCH v2] arch: arm: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
Date: Sat, 11 Jul 2020 21:59:26 +0800	[thread overview]
Message-ID: <20200711135925.GG21277@dragon> (raw)
In-Reply-To: <1592623696-21485-1-git-send-email-sunil@amarulasolutions.com>

On Sat, Jun 20, 2020 at 08:58:16AM +0530, Suniel Mahesh wrote:
> From: Michael Trimarchi <michael@amarulasolutions.com>
> 
> The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID
> because of which when card is inserted, usb otg is enumerated
> and the card is never detected.
> 
> [   64.492645] cfg80211: failed to load regulatory.db
> [   64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
> [   76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller
> [   76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
> [   76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
> [   76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
> [   76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [   76.412763] usb usb2: Product: EHCI Host Controller
> [   76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd
> [   76.424623] usb usb2: SerialNumber: ci_hdrc.0
> [   76.431755] hub 2-0:1.0: USB hub found
> [   76.435862] hub 2-0:1.0: 1 port detected
> 
> The TRM mentions GPIO_1 pad should be muxed/assigned for card detect
> and ENET_RX_ER pad for USB_OTG_ID for proper operation.
> 
> This patch fixes pin muxing as per TRM and is tested on a
> i.Core 1.5 MX6 DL SOM.
> 
> [   22.449165] mmc0: host does not support reading read-only switch, assuming write-enable
> [   22.459992] mmc0: new high speed SDHC card at address 0001
> [   22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
> [   22.478856]  mmcblk0: p1 p2
> 
> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>

Do you need to have Fixes tag and copy stable kernel?

Also, subject prefix should be like 'ARM: dts: ...'

Shawn

> ---
> Changes for v2:
> - Changed patch description as suggested by Michael Trimarchi to make it
>   more readable/understandable.
> ---
>  arch/arm/boot/dts/imx6qdl-icore.dtsi | 3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/imx6qdl-icore.dtsi
> index 756f3a9..12997da 100644
> --- a/arch/arm/boot/dts/imx6qdl-icore.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-icore.dtsi
> @@ -397,7 +397,7 @@
>  
>  	pinctrl_usbotg: usbotggrp {
>  		fsl,pins = <
> -			MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
> +			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
>  		>;
>  	};
>  
> @@ -409,6 +409,7 @@
>  			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17070
>  			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17070
>  			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17070
> +			MX6QDL_PAD_GPIO_1__GPIO1_IO01  0x1b0b0
>  		>;
>  	};
>  
> -- 
> 2.7.4
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel