* [PATCH 1/3] dt-bindings: vendor-prefixes: add Seeed Studio
@ 2020-07-06 17:33 ` Marcin Sloniewski
0 siblings, 0 replies; 12+ messages in thread
From: Marcin Sloniewski @ 2020-07-06 17:33 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marcin Sloniewski, Rob Herring, Maxime Coquelin, Alexandre Torgue,
Manivannan Sadhasivam, Ahmad Fatoum, Sam Ravnborg, Linus Walleij,
Heiko Stuebner, Stephan Gerhold, Lubomir Rintel, Mark Brown,
allen, devicetree, linux-stm32, linux-kernel
Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
Website: https://www.seeedstudio.com/
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 9aeab66be85f..7dd03b3e9d3c 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -902,6 +902,8 @@ patternProperties:
description: Schindler
"^seagate,.*":
description: Seagate Technology PLC
+ "^seeed,.*":
+ description: Seeed Technology Co., Ltd
"^seirobotics,.*":
description: Shenzhen SEI Robotics Co., Ltd
"^semtech,.*":
--
2.26.2
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 2/3] dt-bindings: arm: stm32: document Odyssey compatible
2020-07-06 17:33 ` Marcin Sloniewski
@ 2020-07-06 17:33 ` Marcin Sloniewski
-1 siblings, 0 replies; 12+ messages in thread
From: Marcin Sloniewski @ 2020-07-06 17:33 UTC (permalink / raw)
To: linux-arm-kernel
Cc: devicetree, Ahmad Fatoum, Alexandre Torgue, Stephan Gerhold,
Manivannan Sadhasivam, Heiko Stuebner, Linus Walleij,
linux-kernel, Lubomir Rintel, Marcin Sloniewski, Rob Herring,
Mark Brown, Maxime Coquelin, allen, Sam Ravnborg, linux-stm32
Document device tree bindings of Seeed SoM and carrier board.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
---
Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
index 790e6dd48e34..22b9aaa75eee 100644
--- a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
+++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
@@ -39,6 +39,8 @@ properties:
- enum:
- arrow,stm32mp157a-avenger96 # Avenger96
- lxa,stm32mp157c-mc1
+ - seeed,stm32mp157c-odyssey
+ - seeed,stm32mp157c-odyssey-som
- shiratech,stm32mp157a-iot-box # IoT Box
- shiratech,stm32mp157a-stinger96 # Stinger96
- st,stm32mp157c-ed1
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 2/3] dt-bindings: arm: stm32: document Odyssey compatible
@ 2020-07-06 17:33 ` Marcin Sloniewski
0 siblings, 0 replies; 12+ messages in thread
From: Marcin Sloniewski @ 2020-07-06 17:33 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marcin Sloniewski, Rob Herring, Maxime Coquelin, Alexandre Torgue,
Manivannan Sadhasivam, Ahmad Fatoum, Sam Ravnborg, Linus Walleij,
Stephan Gerhold, Heiko Stuebner, Lubomir Rintel, Mark Brown,
allen, devicetree, linux-stm32, linux-kernel
Document device tree bindings of Seeed SoM and carrier board.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
---
Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
index 790e6dd48e34..22b9aaa75eee 100644
--- a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
+++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml
@@ -39,6 +39,8 @@ properties:
- enum:
- arrow,stm32mp157a-avenger96 # Avenger96
- lxa,stm32mp157c-mc1
+ - seeed,stm32mp157c-odyssey
+ - seeed,stm32mp157c-odyssey-som
- shiratech,stm32mp157a-iot-box # IoT Box
- shiratech,stm32mp157a-stinger96 # Stinger96
- st,stm32mp157c-ed1
--
2.26.2
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH 2/3] dt-bindings: arm: stm32: document Odyssey compatible
2020-07-06 17:33 ` Marcin Sloniewski
@ 2020-07-15 22:04 ` Rob Herring
-1 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2020-07-15 22:04 UTC (permalink / raw)
To: Marcin Sloniewski
Cc: devicetree, Ahmad Fatoum, Alexandre Torgue, Stephan Gerhold,
Manivannan Sadhasivam, Heiko Stuebner, Linus Walleij,
linux-kernel, Lubomir Rintel, Rob Herring, Mark Brown,
Maxime Coquelin, allen, Sam Ravnborg, linux-stm32,
linux-arm-kernel
On Mon, 06 Jul 2020 19:33:48 +0200, Marcin Sloniewski wrote:
> Document device tree bindings of Seeed SoM and carrier board.
>
> Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/3] dt-bindings: arm: stm32: document Odyssey compatible
@ 2020-07-15 22:04 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2020-07-15 22:04 UTC (permalink / raw)
To: Marcin Sloniewski
Cc: Linus Walleij, Ahmad Fatoum, linux-kernel, linux-stm32,
linux-arm-kernel, Manivannan Sadhasivam, Rob Herring,
Sam Ravnborg, devicetree, Mark Brown, Stephan Gerhold,
Heiko Stuebner, allen, Lubomir Rintel, Alexandre Torgue,
Maxime Coquelin
On Mon, 06 Jul 2020 19:33:48 +0200, Marcin Sloniewski wrote:
> Document device tree bindings of Seeed SoM and carrier board.
>
> Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
> ---
> Documentation/devicetree/bindings/arm/stm32/stm32.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
2020-07-06 17:33 ` Marcin Sloniewski
@ 2020-07-06 17:33 ` Marcin Sloniewski
-1 siblings, 0 replies; 12+ messages in thread
From: Marcin Sloniewski @ 2020-07-06 17:33 UTC (permalink / raw)
To: linux-arm-kernel
Cc: devicetree, Ahmad Fatoum, Alexandre Torgue, Stephan Gerhold,
Manivannan Sadhasivam, Heiko Stuebner, Linus Walleij,
linux-kernel, Lubomir Rintel, Marcin Sloniewski, Rob Herring,
Mark Brown, Maxime Coquelin, allen, Sam Ravnborg, linux-stm32
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
---
.../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
2 files changed, 348 insertions(+)
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 000000000000..620ff9e7f370
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C SOM";
+ compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+ memory@c0000000 {
+ reg = <0xc0000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ gpu_reserved: gpu@d4000000 {
+ reg = <0xd4000000 0x4000000>;
+ no-map;
+ };
+ };
+
+ led {
+ compatible = "gpio-leds";
+ blue {
+ label = "heartbeat";
+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+ ldo1-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v3v3_hdmi: ldo2 {
+ regulator-name = "v3v3_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v2_hdmi: ldo6 {
+ regulator-name = "v1v2_hdmi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
new file mode 100644
index 000000000000..6c1b091af14f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C Board";
+ compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ serial0 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-1 = <&i2c1_pins_sleep_a>;
+ i2c-scl-rising-time-ns = <100>;
+ i2c-scl-falling-time-ns = <7>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
--
2.26.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
@ 2020-07-06 17:33 ` Marcin Sloniewski
0 siblings, 0 replies; 12+ messages in thread
From: Marcin Sloniewski @ 2020-07-06 17:33 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Marcin Sloniewski, Rob Herring, Maxime Coquelin, Alexandre Torgue,
Manivannan Sadhasivam, Ahmad Fatoum, Sam Ravnborg, Linus Walleij,
Heiko Stuebner, Stephan Gerhold, Lubomir Rintel, Mark Brown,
allen, devicetree, linux-stm32, linux-kernel
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
---
.../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
2 files changed, 348 insertions(+)
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 000000000000..620ff9e7f370
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C SOM";
+ compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+ memory@c0000000 {
+ reg = <0xc0000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+
+ gpu_reserved: gpu@d4000000 {
+ reg = <0xd4000000 0x4000000>;
+ no-map;
+ };
+ };
+
+ led {
+ compatible = "gpio-leds";
+ blue {
+ label = "heartbeat";
+ gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+};
+
+&gpu {
+ contiguous-area = <&gpu_reserved>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /* spare dmas for other usage */
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+ ldo1-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v3v3_hdmi: ldo2 {
+ regulator-name = "v3v3_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v2_hdmi: ldo6 {
+ regulator-name = "v1v2_hdmi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ power-off-time-sec = <10>;
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ vqmmc-supply = <&v3v3>;
+ mmc-ddr-3_3v;
+ status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
new file mode 100644
index 000000000000..6c1b091af14f
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+ model = "Seeed Studio Odyssey-STM32MP157C Board";
+ compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ serial0 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii-id";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_pins_a>;
+ pinctrl-1 = <&i2c1_pins_sleep_a>;
+ i2c-scl-rising-time-ns = <100>;
+ i2c-scl-falling-time-ns = <7>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
--
2.26.2
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
2020-07-06 17:33 ` Marcin Sloniewski
@ 2020-07-21 9:26 ` Alexandre Torgue
-1 siblings, 0 replies; 12+ messages in thread
From: Alexandre Torgue @ 2020-07-21 9:26 UTC (permalink / raw)
To: Marcin Sloniewski, linux-arm-kernel
Cc: devicetree, Ahmad Fatoum, Stephan Gerhold, Manivannan Sadhasivam,
Heiko Stuebner, Linus Walleij, linux-kernel, Lubomir Rintel,
Rob Herring, Mark Brown, Maxime Coquelin, allen, Sam Ravnborg,
linux-stm32
Hi Marcin,
On 7/6/20 7:33 PM, Marcin Sloniewski wrote:
> Add support for Seeed Studio's stm32mp157c odyssey board.
> Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
> and carrier board with USB and ETH interfaces, SD card connector,
> wifi and BT chip AP6236.
>
> In this patch only basic kernel boot is supported and interfacing
> SD card and on-board eMMC.
>
> Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Thanks for adding a new STM32MP157 board. Nothing to say about your DT
patchs except that Makefile update is missing.
regards
Alex
> ---
> .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
> arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
> 2 files changed, 348 insertions(+)
> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
>
> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> new file mode 100644
> index 000000000000..620ff9e7f370
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> @@ -0,0 +1,276 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157.dtsi"
> +#include "stm32mp15xc.dtsi"
> +#include "stm32mp15-pinctrl.dtsi"
> +#include "stm32mp15xxac-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/mfd/st,stpmic1.h>
> +
> +/ {
> + model = "Seeed Studio Odyssey-STM32MP157C SOM";
> + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
> +
> + memory@c0000000 {
> + reg = <0xc0000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + mcuram2: mcuram2@10000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10000000 0x40000>;
> + no-map;
> + };
> +
> + vdev0vring0: vdev0vring0@10040000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10040000 0x1000>;
> + no-map;
> + };
> +
> + vdev0vring1: vdev0vring1@10041000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10041000 0x1000>;
> + no-map;
> + };
> +
> + vdev0buffer: vdev0buffer@10042000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10042000 0x4000>;
> + no-map;
> + };
> +
> + mcuram: mcuram@30000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x30000000 0x40000>;
> + no-map;
> + };
> +
> + retram: retram@38000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x38000000 0x10000>;
> + no-map;
> + };
> +
> + gpu_reserved: gpu@d4000000 {
> + reg = <0xd4000000 0x4000000>;
> + no-map;
> + };
> + };
> +
> + led {
> + compatible = "gpio-leds";
> + blue {
> + label = "heartbeat";
> + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + default-state = "off";
> + };
> + };
> +};
> +
> +&gpu {
> + contiguous-area = <&gpu_reserved>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> + /* spare dmas for other usage */
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +
> + pmic: stpmic@33 {
> + compatible = "st,stpmic1";
> + reg = <0x33>;
> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "okay";
> +
> + regulators {
> + compatible = "st,stpmic1-regulators";
> + ldo1-supply = <&v3v3>;
> + ldo3-supply = <&vdd_ddr>;
> + ldo6-supply = <&v3v3>;
> + pwr_sw1-supply = <&bst_out>;
> + pwr_sw2-supply = <&bst_out>;
> +
> + vddcore: buck1 {
> + regulator-name = "vddcore";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd_ddr: buck2 {
> + regulator-name = "vdd_ddr";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd: buck3 {
> + regulator-name = "vdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + st,mask-reset;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + v3v3: buck4 {
> + regulator-name = "v3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + regulator-initial-mode = <0>;
> + };
> +
> + v1v8_audio: ldo1 {
> + regulator-name = "v1v8_audio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO1 0>;
> + };
> +
> + v3v3_hdmi: ldo2 {
> + regulator-name = "v3v3_hdmi";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO2 0>;
> + };
> +
> + vtt_ddr: ldo3 {
> + regulator-name = "vtt_ddr";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <750000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + vdd_usb: ldo4 {
> + regulator-name = "vdd_usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + interrupts = <IT_CURLIM_LDO4 0>;
> + };
> +
> + vdda: ldo5 {
> + regulator-name = "vdda";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO5 0>;
> + regulator-boot-on;
> + };
> +
> + v1v2_hdmi: ldo6 {
> + regulator-name = "v1v2_hdmi";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO6 0>;
> + };
> +
> + vref_ddr: vref_ddr {
> + regulator-name = "vref_ddr";
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + bst_out: boost {
> + regulator-name = "bst_out";
> + interrupts = <IT_OCP_BOOST 0>;
> + };
> +
> + vbus_otg: pwr_sw1 {
> + regulator-name = "vbus_otg";
> + interrupts = <IT_OCP_OTG 0>;
> + };
> +
> + vbus_sw: pwr_sw2 {
> + regulator-name = "vbus_sw";
> + interrupts = <IT_OCP_SWOUT 0>;
> + regulator-active-discharge;
> + };
> + };
> +
> + onkey {
> + compatible = "st,stpmic1-onkey";
> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> + interrupt-names = "onkey-falling", "onkey-rising";
> + power-off-time-sec = <10>;
> + status = "okay";
> + };
> +
> + watchdog {
> + compatible = "st,stpmic1-wdt";
> + status = "disabled";
> + };
> + };
> +};
> +
> +&ipcc {
> + status = "okay";
> +};
> +
> +&iwdg2 {
> + timeout-sec = <32>;
> + status = "okay";
> +};
> +
> +&m4_rproc {
> + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
> + <&vdev0vring1>, <&vdev0buffer>;
> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> + mbox-names = "vq0", "vq1", "shutdown";
> + interrupt-parent = <&exti>;
> + interrupts = <68 1>;
> + status = "okay";
> +};
> +
> +&rng1 {
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + vqmmc-supply = <&v3v3>;
> + mmc-ddr-3_3v;
> + status = "okay";
> +};
> +
> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> new file mode 100644
> index 000000000000..6c1b091af14f
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> @@ -0,0 +1,72 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157c-odyssey-som.dtsi"
> +
> +/ {
> + model = "Seeed Studio Odyssey-STM32MP157C Board";
> + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
> +
> + aliases {
> + ethernet0 = ðernet0;
> + serial0 = &uart4;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +ðernet0 {
> + status = "okay";
> + pinctrl-0 = <ðernet0_rgmii_pins_a>;
> + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
> + pinctrl-names = "default", "sleep";
> + phy-mode = "rgmii-id";
> + max-speed = <1000>;
> + phy-handle = <&phy0>;
> +
> + mdio0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c1_pins_a>;
> + pinctrl-1 = <&i2c1_pins_sleep_a>;
> + i2c-scl-rising-time-ns = <100>;
> + i2c-scl-falling-time-ns = <7>;
> + status = "okay";
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +};
> +
> +&sdmmc1 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + disable-wp;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_pins_a>;
> + status = "okay";
> +};
> +
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH 3/3] ARM: dts: stm32: add initial support for stm32mp157-odyssey board
@ 2020-07-21 9:26 ` Alexandre Torgue
0 siblings, 0 replies; 12+ messages in thread
From: Alexandre Torgue @ 2020-07-21 9:26 UTC (permalink / raw)
To: Marcin Sloniewski, linux-arm-kernel
Cc: Rob Herring, Maxime Coquelin, Manivannan Sadhasivam, Ahmad Fatoum,
Sam Ravnborg, Linus Walleij, Heiko Stuebner, Stephan Gerhold,
Lubomir Rintel, Mark Brown, allen, devicetree, linux-stm32,
linux-kernel
Hi Marcin,
On 7/6/20 7:33 PM, Marcin Sloniewski wrote:
> Add support for Seeed Studio's stm32mp157c odyssey board.
> Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
> and carrier board with USB and ETH interfaces, SD card connector,
> wifi and BT chip AP6236.
>
> In this patch only basic kernel boot is supported and interfacing
> SD card and on-board eMMC.
>
> Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Thanks for adding a new STM32MP157 board. Nothing to say about your DT
patchs except that Makefile update is missing.
regards
Alex
> ---
> .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
> arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
> 2 files changed, 348 insertions(+)
> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
>
> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> new file mode 100644
> index 000000000000..620ff9e7f370
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> @@ -0,0 +1,276 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157.dtsi"
> +#include "stm32mp15xc.dtsi"
> +#include "stm32mp15-pinctrl.dtsi"
> +#include "stm32mp15xxac-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/mfd/st,stpmic1.h>
> +
> +/ {
> + model = "Seeed Studio Odyssey-STM32MP157C SOM";
> + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
> +
> + memory@c0000000 {
> + reg = <0xc0000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + mcuram2: mcuram2@10000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10000000 0x40000>;
> + no-map;
> + };
> +
> + vdev0vring0: vdev0vring0@10040000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10040000 0x1000>;
> + no-map;
> + };
> +
> + vdev0vring1: vdev0vring1@10041000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10041000 0x1000>;
> + no-map;
> + };
> +
> + vdev0buffer: vdev0buffer@10042000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10042000 0x4000>;
> + no-map;
> + };
> +
> + mcuram: mcuram@30000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x30000000 0x40000>;
> + no-map;
> + };
> +
> + retram: retram@38000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x38000000 0x10000>;
> + no-map;
> + };
> +
> + gpu_reserved: gpu@d4000000 {
> + reg = <0xd4000000 0x4000000>;
> + no-map;
> + };
> + };
> +
> + led {
> + compatible = "gpio-leds";
> + blue {
> + label = "heartbeat";
> + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + default-state = "off";
> + };
> + };
> +};
> +
> +&gpu {
> + contiguous-area = <&gpu_reserved>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> + /* spare dmas for other usage */
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +
> + pmic: stpmic@33 {
> + compatible = "st,stpmic1";
> + reg = <0x33>;
> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "okay";
> +
> + regulators {
> + compatible = "st,stpmic1-regulators";
> + ldo1-supply = <&v3v3>;
> + ldo3-supply = <&vdd_ddr>;
> + ldo6-supply = <&v3v3>;
> + pwr_sw1-supply = <&bst_out>;
> + pwr_sw2-supply = <&bst_out>;
> +
> + vddcore: buck1 {
> + regulator-name = "vddcore";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd_ddr: buck2 {
> + regulator-name = "vdd_ddr";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd: buck3 {
> + regulator-name = "vdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + st,mask-reset;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + v3v3: buck4 {
> + regulator-name = "v3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + regulator-initial-mode = <0>;
> + };
> +
> + v1v8_audio: ldo1 {
> + regulator-name = "v1v8_audio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO1 0>;
> + };
> +
> + v3v3_hdmi: ldo2 {
> + regulator-name = "v3v3_hdmi";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO2 0>;
> + };
> +
> + vtt_ddr: ldo3 {
> + regulator-name = "vtt_ddr";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <750000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + vdd_usb: ldo4 {
> + regulator-name = "vdd_usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + interrupts = <IT_CURLIM_LDO4 0>;
> + };
> +
> + vdda: ldo5 {
> + regulator-name = "vdda";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO5 0>;
> + regulator-boot-on;
> + };
> +
> + v1v2_hdmi: ldo6 {
> + regulator-name = "v1v2_hdmi";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO6 0>;
> + };
> +
> + vref_ddr: vref_ddr {
> + regulator-name = "vref_ddr";
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + bst_out: boost {
> + regulator-name = "bst_out";
> + interrupts = <IT_OCP_BOOST 0>;
> + };
> +
> + vbus_otg: pwr_sw1 {
> + regulator-name = "vbus_otg";
> + interrupts = <IT_OCP_OTG 0>;
> + };
> +
> + vbus_sw: pwr_sw2 {
> + regulator-name = "vbus_sw";
> + interrupts = <IT_OCP_SWOUT 0>;
> + regulator-active-discharge;
> + };
> + };
> +
> + onkey {
> + compatible = "st,stpmic1-onkey";
> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> + interrupt-names = "onkey-falling", "onkey-rising";
> + power-off-time-sec = <10>;
> + status = "okay";
> + };
> +
> + watchdog {
> + compatible = "st,stpmic1-wdt";
> + status = "disabled";
> + };
> + };
> +};
> +
> +&ipcc {
> + status = "okay";
> +};
> +
> +&iwdg2 {
> + timeout-sec = <32>;
> + status = "okay";
> +};
> +
> +&m4_rproc {
> + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
> + <&vdev0vring1>, <&vdev0buffer>;
> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> + mbox-names = "vq0", "vq1", "shutdown";
> + interrupt-parent = <&exti>;
> + interrupts = <68 1>;
> + status = "okay";
> +};
> +
> +&rng1 {
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + vqmmc-supply = <&v3v3>;
> + mmc-ddr-3_3v;
> + status = "okay";
> +};
> +
> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> new file mode 100644
> index 000000000000..6c1b091af14f
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> @@ -0,0 +1,72 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157c-odyssey-som.dtsi"
> +
> +/ {
> + model = "Seeed Studio Odyssey-STM32MP157C Board";
> + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
> +
> + aliases {
> + ethernet0 = ðernet0;
> + serial0 = &uart4;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +ðernet0 {
> + status = "okay";
> + pinctrl-0 = <ðernet0_rgmii_pins_a>;
> + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
> + pinctrl-names = "default", "sleep";
> + phy-mode = "rgmii-id";
> + max-speed = <1000>;
> + phy-handle = <&phy0>;
> +
> + mdio0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c1_pins_a>;
> + pinctrl-1 = <&i2c1_pins_sleep_a>;
> + i2c-scl-rising-time-ns = <100>;
> + i2c-scl-falling-time-ns = <7>;
> + status = "okay";
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +};
> +
> +&sdmmc1 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + disable-wp;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_pins_a>;
> + status = "okay";
> +};
> +
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/3] dt-bindings: vendor-prefixes: add Seeed Studio
2020-07-06 17:33 ` Marcin Sloniewski
@ 2020-07-15 22:03 ` Rob Herring
-1 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2020-07-15 22:03 UTC (permalink / raw)
To: Marcin Sloniewski
Cc: devicetree, Linus Walleij, Ahmad Fatoum, Alexandre Torgue,
Stephan Gerhold, Manivannan Sadhasivam, Heiko Stuebner,
Mark Brown, linux-kernel, Lubomir Rintel, Rob Herring,
Maxime Coquelin, allen, Sam Ravnborg, linux-stm32,
linux-arm-kernel
On Mon, 06 Jul 2020 19:33:47 +0200, Marcin Sloniewski wrote:
> Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
> Website: https://www.seeedstudio.com/
>
> Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 1/3] dt-bindings: vendor-prefixes: add Seeed Studio
@ 2020-07-15 22:03 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2020-07-15 22:03 UTC (permalink / raw)
To: Marcin Sloniewski
Cc: Heiko Stuebner, devicetree, Manivannan Sadhasivam,
Maxime Coquelin, Rob Herring, linux-stm32, Mark Brown,
Lubomir Rintel, allen, linux-kernel, Sam Ravnborg,
Alexandre Torgue, linux-arm-kernel, Ahmad Fatoum, Linus Walleij,
Stephan Gerhold
On Mon, 06 Jul 2020 19:33:47 +0200, Marcin Sloniewski wrote:
> Add the "seeed" vendor prefix for Seeed Technology Co., Ltd
> Website: https://www.seeedstudio.com/
>
> Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
> ---
> Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread