* [PATCH v4 1/5] MIPS: Ingenic: Add Ingenic X1830 support.
2020-07-14 5:32 [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
@ 2020-07-14 5:32 ` 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` [PATCH v4 2/5] dt-bindings: MIPS: Add X1830 based CU1830-Neo and fix bug in CU1000-Neo 周琰杰 (Zhou Yanjie)
` (4 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-07-14 5:32 UTC (permalink / raw)
To: tsbogend, robh+dt
Cc: linux-mips, devicetree, linux-kernel, paulburton, paul, ak,
ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
Support the Ingenic X1830 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1830 based board is
added in a later commit.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v1->v2:
No change.
v2->v3:
Adjust the order of nodes according to the
corresponding address value.
v3->v4:
No change.
arch/mips/boot/dts/ingenic/x1830.dtsi | 300 ++++++++++++++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 6 +
2 files changed, 306 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/x1830.dtsi
diff --git a/arch/mips/boot/dts/ingenic/x1830.dtsi b/arch/mips/boot/dts/ingenic/x1830.dtsi
new file mode 100644
index 000000000000..eb1214481a33
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1830.dtsi
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/clock/x1830-cgu.h>
+#include <dt-bindings/dma/x1830-dma.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "ingenic,x1830";
+
+ cpuintc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ compatible = "mti,cpu-interrupt-controller";
+ };
+
+ intc: interrupt-controller@10001000 {
+ compatible = "ingenic,x1830-intc", "ingenic,jz4780-intc";
+ reg = <0x10001000 0x50>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&cpuintc>;
+ interrupts = <2>;
+ };
+
+ exclk: ext {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ rtclk: rtc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+
+ cgu: x1830-cgu@10000000 {
+ compatible = "ingenic,x1830-cgu";
+ reg = <0x10000000 0x100>;
+
+ #clock-cells = <1>;
+
+ clocks = <&exclk>, <&rtclk>;
+ clock-names = "ext", "rtc";
+ };
+
+ tcu: timer@10002000 {
+ compatible = "ingenic,x1830-tcu", "ingenic,x1000-tcu", "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu X1830_CLK_RTCLK
+ &cgu X1830_CLK_EXCLK
+ &cgu X1830_CLK_PCLK>;
+ clock-names = "rtc", "ext", "pclk";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27 26 25>;
+
+ wdt: watchdog@0 {
+ compatible = "ingenic,x1830-watchdog", "ingenic,jz4780-watchdog";
+ reg = <0x0 0x10>;
+
+ clocks = <&tcu TCU_CLK_WDT>;
+ clock-names = "wdt";
+ };
+ };
+
+ rtc: rtc@10003000 {
+ compatible = "ingenic,x1830-rtc", "ingenic,jz4780-rtc";
+ reg = <0x10003000 0x4c>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <32>;
+
+ clocks = <&cgu X1830_CLK_RTCLK>;
+ clock-names = "rtc";
+ };
+
+ pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,x1830-pinctrl";
+ reg = <0x10010000 0x800>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+ };
+
+ gpb: gpio@1 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <1>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 32 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <16>;
+ };
+
+ gpc: gpio@2 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <2>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 64 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <15>;
+ };
+
+ gpd: gpio@3 {
+ compatible = "ingenic,x1830-gpio";
+ reg = <3>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 96 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <14>;
+ };
+ };
+
+ uart0: serial@10030000 {
+ compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+ reg = <0x10030000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <51>;
+
+ clocks = <&exclk>, <&cgu X1830_CLK_UART0>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart1: serial@10031000 {
+ compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+ reg = <0x10031000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <50>;
+
+ clocks = <&exclk>, <&cgu X1830_CLK_UART1>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ i2c0: i2c-controller@10050000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10050000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <60>;
+
+ clocks = <&cgu X1830_CLK_SMB0>;
+
+ status = "disabled";
+ };
+
+ i2c1: i2c-controller@10051000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10051000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <59>;
+
+ clocks = <&cgu X1830_CLK_SMB1>;
+
+ status = "disabled";
+ };
+
+ i2c2: i2c-controller@10052000 {
+ compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+ reg = <0x10052000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <58>;
+
+ clocks = <&cgu X1830_CLK_SMB2>;
+
+ status = "disabled";
+ };
+
+ pdma: dma-controller@13420000 {
+ compatible = "ingenic,x1830-dma";
+ reg = <0x13420000 0x400
+ 0x13421000 0x40>;
+ #dma-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <10>;
+
+ clocks = <&cgu X1830_CLK_PDMA>;
+ };
+
+ msc0: mmc@13450000 {
+ compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+ reg = <0x13450000 0x1000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <37>;
+
+ clocks = <&cgu X1830_CLK_MSC0>;
+ clock-names = "mmc";
+
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+
+ dmas = <&pdma X1830_DMA_MSC0_RX 0xffffffff>,
+ <&pdma X1830_DMA_MSC0_TX 0xffffffff>;
+ dma-names = "rx", "tx";
+
+ status = "disabled";
+ };
+
+ msc1: mmc@13460000 {
+ compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+ reg = <0x13460000 0x1000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <36>;
+
+ clocks = <&cgu X1830_CLK_MSC1>;
+ clock-names = "mmc";
+
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ cap-sdio-irq;
+
+ dmas = <&pdma X1830_DMA_MSC1_RX 0xffffffff>,
+ <&pdma X1830_DMA_MSC1_TX 0xffffffff>;
+ dma-names = "rx", "tx";
+
+ status = "disabled";
+ };
+
+ mac: ethernet@134b0000 {
+ compatible = "ingenic,x1830-mac", "snps,dwmac";
+ reg = <0x134b0000 0x2000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <55>;
+ interrupt-names = "macirq";
+
+ clocks = <&cgu X1830_CLK_MAC>;
+ clock-names = "stmmaceth";
+
+ status = "disabled";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 9c2e8c15bb97..cd0ddb52da99 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -50,3 +50,9 @@ config MACH_X1000
select MIPS_CPU_SCACHE
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1830
+ bool
+ select MIPS_CPU_SCACHE
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_SUPPORTS_HIGHMEM
--
2.11.0
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v4 2/5] dt-bindings: MIPS: Add X1830 based CU1830-Neo and fix bug in CU1000-Neo.
2020-07-14 5:32 [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` [PATCH v4 1/5] MIPS: Ingenic: Add Ingenic X1830 support 周琰杰 (Zhou Yanjie)
@ 2020-07-14 5:32 ` 周琰杰 (Zhou Yanjie)
2020-07-14 20:49 ` Rob Herring
2020-07-14 5:32 ` [PATCH v4 3/5] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
` (3 subsequent siblings)
5 siblings, 1 reply; 8+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-07-14 5:32 UTC (permalink / raw)
To: tsbogend, robh+dt
Cc: linux-mips, devicetree, linux-kernel, paulburton, paul, ak,
ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
1.Add bindings for Ingenic X1830 based board, prepare for later dts.
2.The CU1000-Neo board actually uses X1000E instead of X1000, so
the wrongly written "ingenic,x1000" in bindings should be changed
to "ingenic,x1000e", the corresponding dts file modification will
be made in a patch later in this series.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v1->v2:
No change.
v2->v3:
No change.
v3->v4:
Modify the commit message and add the change description
for CU1000-Neo.
Documentation/devicetree/bindings/mips/ingenic/devices.yaml | 12 +++++++++---
1 file changed, 9 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
index d1175030781a..feb695be9f66 100644
--- a/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
+++ b/Documentation/devicetree/bindings/mips/ingenic/devices.yaml
@@ -8,7 +8,8 @@ title: Ingenic XBurst based Platforms Device Tree Bindings
maintainers:
- 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
-description: |
+
+description:
Devices with a Ingenic XBurst CPU shall have the following properties.
properties:
@@ -32,8 +33,13 @@ properties:
- const: img,ci20
- const: ingenic,jz4780
- - description: YSH & ATIL General Board CU Neo
+ - description: YSH & ATIL General Board, CU1000 Module with Neo Backplane
items:
- const: yna,cu1000-neo
- - const: ingenic,x1000
+ - const: ingenic,x1000e
+
+ - description: YSH & ATIL General Board, CU1830 Module with Neo Backplane
+ items:
+ - const: yna,cu1830-neo
+ - const: ingenic,x1830
...
--
2.11.0
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH v4 2/5] dt-bindings: MIPS: Add X1830 based CU1830-Neo and fix bug in CU1000-Neo.
2020-07-14 5:32 ` [PATCH v4 2/5] dt-bindings: MIPS: Add X1830 based CU1830-Neo and fix bug in CU1000-Neo 周琰杰 (Zhou Yanjie)
@ 2020-07-14 20:49 ` Rob Herring
0 siblings, 0 replies; 8+ messages in thread
From: Rob Herring @ 2020-07-14 20:49 UTC (permalink / raw)
To: 周琰杰 (Zhou Yanjie)
Cc: linux-kernel, yanfei.li, dongsheng.qiu, zhenwenjin, rick.tyliu,
paulburton, sernia.zhou, ebiederm, aric.pzqi, tsbogend,
linux-mips, devicetree, ak, paul, robh+dt
On Tue, 14 Jul 2020 13:32:26 +0800, 周琰杰 (Zhou Yanjie) wrote:
> 1.Add bindings for Ingenic X1830 based board, prepare for later dts.
> 2.The CU1000-Neo board actually uses X1000E instead of X1000, so
> the wrongly written "ingenic,x1000" in bindings should be changed
> to "ingenic,x1000e", the corresponding dts file modification will
> be made in a patch later in this series.
>
> Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
> ---
>
> Notes:
> v1->v2:
> No change.
>
> v2->v3:
> No change.
>
> v3->v4:
> Modify the commit message and add the change description
> for CU1000-Neo.
>
> Documentation/devicetree/bindings/mips/ingenic/devices.yaml | 12 +++++++++---
> 1 file changed, 9 insertions(+), 3 deletions(-)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v4 3/5] MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
2020-07-14 5:32 [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` [PATCH v4 1/5] MIPS: Ingenic: Add Ingenic X1830 support 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` [PATCH v4 2/5] dt-bindings: MIPS: Add X1830 based CU1830-Neo and fix bug in CU1000-Neo 周琰杰 (Zhou Yanjie)
@ 2020-07-14 5:32 ` 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` [PATCH v4 4/5] MIPS: Ingenic: Fix bugs and add missing LED node for X1000 周琰杰 (Zhou Yanjie)
` (2 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-07-14 5:32 UTC (permalink / raw)
To: tsbogend, robh+dt
Cc: linux-mips, devicetree, linux-kernel, paulburton, paul, ak,
ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
Add a device tree and a defconfig for the Ingenic X1830 based
YSH & ATIL CU Neo board.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v1->v2:
1.Add DT node for LED.
2.Update defconfig for LED.
v2->v3:
Adjust the order of nodes according to the
corresponding address value.
v3->v4:
No change.
arch/mips/boot/dts/ingenic/Makefile | 1 +
arch/mips/boot/dts/ingenic/cu1830-neo.dts | 168 ++++++++++++++++++++++++++++++
arch/mips/configs/cu1830-neo_defconfig | 123 ++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 4 +
4 files changed, 296 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/cu1830-neo.dts
create mode 100644 arch/mips/configs/cu1830-neo_defconfig
diff --git a/arch/mips/boot/dts/ingenic/Makefile b/arch/mips/boot/dts/ingenic/Makefile
index e1654291a7b0..c33434fad007 100644
--- a/arch/mips/boot/dts/ingenic/Makefile
+++ b/arch/mips/boot/dts/ingenic/Makefile
@@ -3,5 +3,6 @@ dtb-$(CONFIG_JZ4740_QI_LB60) += qi_lb60.dtb
dtb-$(CONFIG_JZ4770_GCW0) += gcw0.dtb
dtb-$(CONFIG_JZ4780_CI20) += ci20.dtb
dtb-$(CONFIG_X1000_CU1000_NEO) += cu1000-neo.dtb
+dtb-$(CONFIG_X1830_CU1830_NEO) += cu1830-neo.dtb
obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/ingenic/cu1830-neo.dts b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
new file mode 100644
index 000000000000..640f96c00d63
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1830.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ compatible = "yna,cu1830-neo", "ingenic,x1830";
+ model = "YSH & ATIL General Board CU1830-Neo";
+
+ aliases {
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x08000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-0 {
+ gpios = <&gpc 17 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ wlan_pwrseq: msc1-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+
+ reset-gpios = <&gpc 13 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&exclk {
+ clock-frequency = <24000000>;
+};
+
+&tcu {
+ /* 1500 kHz for the system timer and clocksource */
+ assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+ assigned-clock-rates = <1500000>, <1500000>;
+
+ /* Use channel #0 for the system timer channel #2 for the clocksource */
+ ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&uart1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart1>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_i2c0>;
+
+ ads7830: adc@48 {
+ compatible = "ti,ads7830";
+ reg = <0x48>;
+ };
+};
+
+&msc0 {
+ status = "okay";
+
+ bus-width = <4>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc0>;
+
+ non-removable;
+};
+
+&msc1 {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ max-frequency = <50000000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_msc1>;
+
+ non-removable;
+
+ mmc-pwrseq = <&wlan_pwrseq>;
+
+ ap6212a: wifi@1 {
+ compatible = "brcm,bcm4329-fmac";
+ reg = <1>;
+
+ interrupt-parent = <&gpc>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "host-wake";
+
+ brcm,drive-strength = <10>;
+ };
+};
+
+&mac {
+ status = "okay";
+
+ phy-mode = "rmii";
+ phy-handle = <&ip101gr>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_mac>;
+
+ snps,reset-gpio = <&gpb 28 GPIO_ACTIVE_LOW>; /* PB28 */
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+ status = "okay";
+
+ ip101gr: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0243.0c54", "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&pinctrl {
+ pins_uart1: uart1 {
+ function = "uart1";
+ groups = "uart1-data";
+ bias-pull-up;
+ };
+
+ pins_i2c0: i2c0 {
+ function = "i2c0";
+ groups = "i2c0-data";
+ bias-pull-up;
+ };
+
+ pins_msc0: msc0 {
+ function = "mmc0";
+ groups = "mmc0-1bit", "mmc0-4bit";
+ bias-disable;
+ };
+
+ pins_msc1: msc1 {
+ function = "mmc1";
+ groups = "mmc1-1bit", "mmc1-4bit";
+ bias-disable;
+ };
+
+ pins_mac: mac {
+ function = "mac";
+ groups = "mac";
+ bias-disable;
+ };
+};
diff --git a/arch/mips/configs/cu1830-neo_defconfig b/arch/mips/configs/cu1830-neo_defconfig
new file mode 100644
index 000000000000..cbfb62900273
--- /dev/null
+++ b/arch/mips/configs/cu1830-neo_defconfig
@@ -0,0 +1,123 @@
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_KERNEL_GZIP=y
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_MEMCG_KMEM=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC=y
+CONFIG_X1830_CU1830_NEO=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_CMA_AREAS=7
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_CFG80211=y
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=y
+CONFIG_BLK_DEV_DM=y
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_ICPLUS_PHY=y
+CONFIG_BRCMFMAC=y
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_EARLYCON=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+CONFIG_I2C_JZ4780=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_SENSORS_ADS7828=y
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_NVMEM=y
+CONFIG_NVMEM_SYSFS=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_PRINTK_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CONSOLE_LOGLEVEL_QUIET=15
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon clk_ignore_unused"
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index cd0ddb52da99..6c065dcaeff8 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -27,6 +27,10 @@ config X1000_CU1000_NEO
bool "YSH & ATIL CU1000 Module with Neo backplane"
select MACH_X1000
+config X1830_CU1830_NEO
+ bool "YSH & ATIL CU1830 Module with Neo backplane"
+ select MACH_X1830
+
endchoice
config MACH_JZ4740
--
2.11.0
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v4 4/5] MIPS: Ingenic: Fix bugs and add missing LED node for X1000.
2020-07-14 5:32 [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
` (2 preceding siblings ...)
2020-07-14 5:32 ` [PATCH v4 3/5] MIPS: Ingenic: Add YSH & ATIL CU Neo board support 周琰杰 (Zhou Yanjie)
@ 2020-07-14 5:32 ` 周琰杰 (Zhou Yanjie)
2020-07-14 5:32 ` [PATCH v4 5/5] MIPS: CU1000-Neo: Refresh defconfig to support LED 周琰杰 (Zhou Yanjie)
2020-07-16 9:51 ` [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board Thomas Bogendoerfer
5 siblings, 0 replies; 8+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-07-14 5:32 UTC (permalink / raw)
To: tsbogend, robh+dt
Cc: linux-mips, devicetree, linux-kernel, paulburton, paul, ak,
ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
1.The CU1000-Neo board actually uses X1000E instead of X1000,
so the wrongly written "ingenic,x1000" in compatible should
be changed to "ingenic,x1000e".
2.Adjust the order of nodes according to the corresponding
address value.
3.Drop unnecessary node in "wlan_pwrseq".
4.Add the leds node to "cu1000-neo.dts".
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v4:
New patch.
arch/mips/boot/dts/ingenic/cu1000-neo.dts | 114 +++++++++++++--------------
arch/mips/boot/dts/ingenic/x1000.dtsi | 126 +++++++++++++++---------------
2 files changed, 118 insertions(+), 122 deletions(-)
diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
index 03abd94acd84..22a1066d637b 100644
--- a/arch/mips/boot/dts/ingenic/cu1000-neo.dts
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -7,8 +7,8 @@
#include <dt-bindings/interrupt-controller/irq.h>
/ {
- compatible = "yna,cu1000-neo", "ingenic,x1000";
- model = "YSH & ATIL General Board CU Neo";
+ compatible = "yna,cu1000-neo", "ingenic,x1000e";
+ model = "YSH & ATIL General Board CU1000-Neo";
aliases {
serial2 = &uart2;
@@ -23,20 +23,19 @@
reg = <0x0 0x04000000>;
};
+ leds {
+ compatible = "gpio-leds";
+ led-0 {
+ gpios = <&gpb 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
wlan_pwrseq: msc1-pwrseq {
compatible = "mmc-pwrseq-simple";
- clocks = <&lpoclk>;
- clock-names = "ext_clock";
-
reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
post-power-on-delay-ms = <200>;
-
- lpoclk: ap6212a {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- };
};
};
@@ -53,6 +52,13 @@
ingenic,pwm-channels-mask = <0xfa>;
};
+&uart2 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_uart2>;
+};
+
&i2c0 {
status = "okay";
@@ -61,43 +67,15 @@
pinctrl-names = "default";
pinctrl-0 = <&pins_i2c0>;
- ads7830@48 {
+ ads7830: adc@48 {
compatible = "ti,ads7830";
reg = <0x48>;
};
};
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pins_uart2>;
-
- status = "okay";
-};
-
-&mac {
- phy-mode = "rmii";
- phy-handle = <&lan8720a>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&pins_mac>;
-
- snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
- snps,reset-active-low;
- snps,reset-delays-us = <0 10000 30000>;
-
- status = "okay";
-};
-
-&mdio {
+&msc0 {
status = "okay";
- lan8720a: ethernet-phy@0 {
- compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- };
-};
-
-&msc0 {
bus-width = <8>;
max-frequency = <50000000>;
@@ -105,26 +83,23 @@
pinctrl-0 = <&pins_msc0>;
non-removable;
-
- status = "okay";
};
&msc1 {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
bus-width = <4>;
max-frequency = <50000000>;
pinctrl-names = "default";
pinctrl-0 = <&pins_msc1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
non-removable;
mmc-pwrseq = <&wlan_pwrseq>;
- status = "okay";
-
ap6212a: wifi@1 {
compatible = "brcm,bcm4329-fmac";
reg = <1>;
@@ -137,23 +112,40 @@
};
};
-&pinctrl {
- pins_i2c0: i2c0 {
- function = "i2c0";
- groups = "i2c0-data";
- bias-disable;
+&mac {
+ status = "okay";
+
+ phy-mode = "rmii";
+ phy-handle = <&lan8720a>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_mac>;
+
+ snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+ status = "okay";
+
+ lan8720a: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
};
+};
+&pinctrl {
pins_uart2: uart2 {
function = "uart2";
groups = "uart2-data-d";
- bias-disable;
+ bias-pull-up;
};
- pins_mac: mac {
- function = "mac";
- groups = "mac";
- bias-disable;
+ pins_i2c0: i2c0 {
+ function = "i2c0";
+ groups = "i2c0-data";
+ bias-pull-up;
};
pins_msc0: msc0 {
@@ -167,4 +159,10 @@
groups = "mmc1-1bit", "mmc1-4bit";
bias-disable;
};
+
+ pins_mac: mac {
+ function = "mac";
+ groups = "mac";
+ bias-disable;
+ };
};
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
index 59a63a0985a8..9de9e7c2d523 100644
--- a/arch/mips/boot/dts/ingenic/x1000.dtsi
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -48,9 +48,7 @@
};
tcu: timer@10002000 {
- compatible = "ingenic,x1000-tcu",
- "ingenic,jz4770-tcu",
- "simple-mfd";
+ compatible = "ingenic,x1000-tcu", "simple-mfd";
reg = <0x10002000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
@@ -156,48 +154,6 @@
};
};
- i2c0: i2c-controller@10050000 {
- compatible = "ingenic,x1000-i2c";
- reg = <0x10050000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- interrupt-parent = <&intc>;
- interrupts = <60>;
-
- clocks = <&cgu X1000_CLK_I2C0>;
-
- status = "disabled";
- };
-
- i2c1: i2c-controller@10051000 {
- compatible = "ingenic,x1000-i2c";
- reg = <0x10051000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- interrupt-parent = <&intc>;
- interrupts = <59>;
-
- clocks = <&cgu X1000_CLK_I2C1>;
-
- status = "disabled";
- };
-
- i2c2: i2c-controller@10052000 {
- compatible = "ingenic,x1000-i2c";
- reg = <0x10052000 0x1000>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- interrupt-parent = <&intc>;
- interrupts = <58>;
-
- clocks = <&cgu X1000_CLK_I2C2>;
-
- status = "disabled";
- };
-
uart0: serial@10030000 {
compatible = "ingenic,x1000-uart";
reg = <0x10030000 0x100>;
@@ -237,37 +193,57 @@
status = "disabled";
};
- pdma: dma-controller@13420000 {
- compatible = "ingenic,x1000-dma";
- reg = <0x13420000 0x400>, <0x13421000 0x40>;
- #dma-cells = <2>;
+ i2c0: i2c-controller@10050000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10050000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
interrupt-parent = <&intc>;
- interrupts = <10>;
+ interrupts = <60>;
- clocks = <&cgu X1000_CLK_PDMA>;
+ clocks = <&cgu X1000_CLK_I2C0>;
+
+ status = "disabled";
};
- mac: ethernet@134b0000 {
- compatible = "ingenic,x1000-mac", "snps,dwmac";
- reg = <0x134b0000 0x2000>;
+ i2c1: i2c-controller@10051000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10051000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
interrupt-parent = <&intc>;
- interrupts = <55>;
- interrupt-names = "macirq";
+ interrupts = <59>;
- clocks = <&cgu X1000_CLK_MAC>;
- clock-names = "stmmaceth";
+ clocks = <&cgu X1000_CLK_I2C1>;
status = "disabled";
+ };
- mdio: mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
+ i2c2: i2c-controller@10052000 {
+ compatible = "ingenic,x1000-i2c";
+ reg = <0x10052000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
- status = "disabled";
- };
+ interrupt-parent = <&intc>;
+ interrupts = <58>;
+
+ clocks = <&cgu X1000_CLK_I2C2>;
+
+ status = "disabled";
+ };
+
+ pdma: dma-controller@13420000 {
+ compatible = "ingenic,x1000-dma";
+ reg = <0x13420000 0x400>, <0x13421000 0x40>;
+ #dma-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <10>;
+
+ clocks = <&cgu X1000_CLK_PDMA>;
};
msc0: mmc@13450000 {
@@ -311,4 +287,26 @@
status = "disabled";
};
+
+ mac: ethernet@134b0000 {
+ compatible = "ingenic,x1000-mac", "snps,dwmac";
+ reg = <0x134b0000 0x2000>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <55>;
+ interrupt-names = "macirq";
+
+ clocks = <&cgu X1000_CLK_MAC>;
+ clock-names = "stmmaceth";
+
+ status = "disabled";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+ };
};
--
2.11.0
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v4 5/5] MIPS: CU1000-Neo: Refresh defconfig to support LED.
2020-07-14 5:32 [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
` (3 preceding siblings ...)
2020-07-14 5:32 ` [PATCH v4 4/5] MIPS: Ingenic: Fix bugs and add missing LED node for X1000 周琰杰 (Zhou Yanjie)
@ 2020-07-14 5:32 ` 周琰杰 (Zhou Yanjie)
2020-07-16 9:51 ` [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board Thomas Bogendoerfer
5 siblings, 0 replies; 8+ messages in thread
From: 周琰杰 (Zhou Yanjie) @ 2020-07-14 5:32 UTC (permalink / raw)
To: tsbogend, robh+dt
Cc: linux-mips, devicetree, linux-kernel, paulburton, paul, ak,
ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
Refresh CU1000-Neo's defconfig to support LED.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
---
Notes:
v4:
New patch.
arch/mips/configs/cu1000-neo_defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/mips/configs/cu1000-neo_defconfig b/arch/mips/configs/cu1000-neo_defconfig
index 9b05a8fdabe1..6b471cdb16cf 100644
--- a/arch/mips/configs/cu1000-neo_defconfig
+++ b/arch/mips/configs/cu1000-neo_defconfig
@@ -74,6 +74,10 @@ CONFIG_JZ4740_WDT=y
# CONFIG_USB_SUPPORT is not set
CONFIG_MMC=y
CONFIG_MMC_JZ4740=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_JZ4740=y
CONFIG_DMADEVICES=y
--
2.11.0
^ permalink raw reply related [flat|nested] 8+ messages in thread* Re: [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board.
2020-07-14 5:32 [PATCH v4 0/5] Add support for Ingenic X1830 SoC and Y&A CU1830-Neo board 周琰杰 (Zhou Yanjie)
` (4 preceding siblings ...)
2020-07-14 5:32 ` [PATCH v4 5/5] MIPS: CU1000-Neo: Refresh defconfig to support LED 周琰杰 (Zhou Yanjie)
@ 2020-07-16 9:51 ` Thomas Bogendoerfer
5 siblings, 0 replies; 8+ messages in thread
From: Thomas Bogendoerfer @ 2020-07-16 9:51 UTC (permalink / raw)
To: 周琰杰 (Zhou Yanjie)
Cc: robh+dt, linux-mips, devicetree, linux-kernel, paulburton, paul,
ak, ebiederm, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li,
sernia.zhou, zhenwenjin
On Tue, Jul 14, 2020 at 01:32:24PM +0800, 周琰杰 (Zhou Yanjie) wrote:
> v3->v4:
> 1.Modify the commit message and add the change description
> for CU1000-Neo in patch [2/5].
> 2.The wrongly written "ingenic,x1000" in compatible is
> changed to "ingenic,x1000e" in "cu1000-neo.dts".
> 3.Adjust the order of nodes according to the corresponding
> address value for X1000.
> 4.Drop unnecessary node in "wlan_pwrseq" in "cu1000-neo.dts".
> 5.Add the leds node to "cu1000-neo.dts".
>
> 周琰杰 (Zhou Yanjie) (5):
> MIPS: Ingenic: Add Ingenic X1830 support.
> dt-bindings: MIPS: Add X1830 based CU1830-Neo and fix bug in
> CU1000-Neo.
> MIPS: Ingenic: Add YSH & ATIL CU Neo board support.
> MIPS: Ingenic: Fix bugs and add missing LED node for X1000.
> MIPS: CU1000-Neo: Refresh defconfig to support LED.
>
> .../devicetree/bindings/mips/ingenic/devices.yaml | 12 +-
> arch/mips/boot/dts/ingenic/Makefile | 1 +
> arch/mips/boot/dts/ingenic/cu1000-neo.dts | 114 ++++----
> arch/mips/boot/dts/ingenic/cu1830-neo.dts | 168 ++++++++++++
> arch/mips/boot/dts/ingenic/x1000.dtsi | 126 +++++----
> arch/mips/boot/dts/ingenic/x1830.dtsi | 300 +++++++++++++++++++++
> arch/mips/configs/cu1000-neo_defconfig | 4 +
> arch/mips/configs/cu1830-neo_defconfig | 123 +++++++++
> arch/mips/jz4740/Kconfig | 10 +
> 9 files changed, 733 insertions(+), 125 deletions(-)
> create mode 100644 arch/mips/boot/dts/ingenic/cu1830-neo.dts
> create mode 100644 arch/mips/boot/dts/ingenic/x1830.dtsi
> create mode 100644 arch/mips/configs/cu1830-neo_defconfig
series applied to mips-next.
Thomas.
--
Crap can work. Given enough thrust pigs will fly, but it's not necessarily a
good idea. [ RFC1925, 2.3 ]
^ permalink raw reply [flat|nested] 8+ messages in thread