From: Manivannan Sadhasivam <mani@kernel.org>
To: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Cc: "Rob Herring" <robh+dt@kernel.org>,
"Andreas Färber" <afaerber@suse.de>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-actions@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 2/2] ARM: dts: owl-s500-roseapplepi: Add ethernet support
Date: Mon, 14 Jun 2021 16:57:33 +0530 [thread overview]
Message-ID: <20210614112733.GA38584@thinkpad> (raw)
In-Reply-To: <d0e1fbf81984127f0352eb740c7129424b5e40f9.1623401998.git.cristian.ciocaltea@gmail.com>
On Fri, Jun 11, 2021 at 12:11:33PM +0300, Cristian Ciocaltea wrote:
> Add pinctrl configuration for enabling the Ethernet MAC on RoseapplePi
> SBC. Additionally, provide the necessary properties for the generic S500
> ethernet node in order to setup PHY and MDIO.
>
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> arch/arm/boot/dts/owl-s500-roseapplepi.dts | 45 ++++++++++++++++++++++
> 1 file changed, 45 insertions(+)
>
> diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> index b8c5db2344aa..eb555f385283 100644
> --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> @@ -225,6 +225,27 @@ bias1-pinconf {
> bias-pull-down;
> };
> };
> +
> + ethernet_pins: ethernet-pins {
> + eth_rmii-pinmux {
> + groups = "rmii_txd0_mfp", "rmii_txd1_mfp",
> + "rmii_rxd0_mfp", "rmii_rxd1_mfp",
> + "rmii_txen_mfp", "rmii_rxen_mfp",
> + "rmii_crs_dv_mfp", "rmii_ref_clk_mfp";
> + function = "eth_rmii";
> + };
> +
> + phy_clk-pinmux {
> + groups = "clko_25m_mfp";
> + function = "clko_25m";
> + };
> +
> + ref_clk-pinconf {
> + groups = "rmii_ref_clk_drv";
> + drive-strength = <2>;
> + };
> +
> + };
> };
>
> /* uSD */
> @@ -241,6 +262,30 @@ &mmc0 {
> vqmmc-supply = <&sd_vcc>;
> };
>
> +ðernet {
> + pinctrl-names = "default";
> + pinctrl-0 = <ðernet_pins>;
> + phy-mode = "rmii";
> + phy-handle = <ð_phy>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reset-gpios = <&pinctrl 88 GPIO_ACTIVE_LOW>; /* GPIOC24 */
> + reset-delay-us = <10000>;
> + reset-post-delay-us = <150000>;
> +
> + eth_phy: ethernet-phy@3 {
> + reg = <0x3>;
> + max-speed = <100>;
> + interrupt-parent = <&sirq>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +};
> +
> &twd_timer {
> status = "okay";
> };
> --
> 2.32.0
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Manivannan Sadhasivam <mani@kernel.org>
To: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Cc: "Rob Herring" <robh+dt@kernel.org>,
"Andreas Färber" <afaerber@suse.de>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-actions@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 2/2] ARM: dts: owl-s500-roseapplepi: Add ethernet support
Date: Mon, 14 Jun 2021 16:57:33 +0530 [thread overview]
Message-ID: <20210614112733.GA38584@thinkpad> (raw)
In-Reply-To: <d0e1fbf81984127f0352eb740c7129424b5e40f9.1623401998.git.cristian.ciocaltea@gmail.com>
On Fri, Jun 11, 2021 at 12:11:33PM +0300, Cristian Ciocaltea wrote:
> Add pinctrl configuration for enabling the Ethernet MAC on RoseapplePi
> SBC. Additionally, provide the necessary properties for the generic S500
> ethernet node in order to setup PHY and MDIO.
>
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> arch/arm/boot/dts/owl-s500-roseapplepi.dts | 45 ++++++++++++++++++++++
> 1 file changed, 45 insertions(+)
>
> diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> index b8c5db2344aa..eb555f385283 100644
> --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> @@ -225,6 +225,27 @@ bias1-pinconf {
> bias-pull-down;
> };
> };
> +
> + ethernet_pins: ethernet-pins {
> + eth_rmii-pinmux {
> + groups = "rmii_txd0_mfp", "rmii_txd1_mfp",
> + "rmii_rxd0_mfp", "rmii_rxd1_mfp",
> + "rmii_txen_mfp", "rmii_rxen_mfp",
> + "rmii_crs_dv_mfp", "rmii_ref_clk_mfp";
> + function = "eth_rmii";
> + };
> +
> + phy_clk-pinmux {
> + groups = "clko_25m_mfp";
> + function = "clko_25m";
> + };
> +
> + ref_clk-pinconf {
> + groups = "rmii_ref_clk_drv";
> + drive-strength = <2>;
> + };
> +
> + };
> };
>
> /* uSD */
> @@ -241,6 +262,30 @@ &mmc0 {
> vqmmc-supply = <&sd_vcc>;
> };
>
> +ðernet {
> + pinctrl-names = "default";
> + pinctrl-0 = <ðernet_pins>;
> + phy-mode = "rmii";
> + phy-handle = <ð_phy>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reset-gpios = <&pinctrl 88 GPIO_ACTIVE_LOW>; /* GPIOC24 */
> + reset-delay-us = <10000>;
> + reset-post-delay-us = <150000>;
> +
> + eth_phy: ethernet-phy@3 {
> + reg = <0x3>;
> + max-speed = <100>;
> + interrupt-parent = <&sirq>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +};
> +
> &twd_timer {
> status = "okay";
> };
> --
> 2.32.0
>
next prev parent reply other threads:[~2021-06-14 11:29 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-11 9:11 [PATCH v2 0/2] Add Ethernet DTS for Actions Semi Owl S500 SoCs Cristian Ciocaltea
2021-06-11 9:11 ` Cristian Ciocaltea
2021-06-11 9:11 ` [PATCH v2 1/2] ARM: dts: owl-s500: Add ethernet support Cristian Ciocaltea
2021-06-11 9:11 ` Cristian Ciocaltea
2021-06-16 13:30 ` kernel test robot
2021-06-16 13:30 ` kernel test robot
2021-06-16 13:30 ` kernel test robot
2021-06-28 6:22 ` Manivannan Sadhasivam
2021-06-28 6:22 ` Manivannan Sadhasivam
2021-06-28 6:22 ` Manivannan Sadhasivam
2021-06-28 7:02 ` Cristian Ciocaltea
2021-06-28 7:02 ` Cristian Ciocaltea
2021-06-28 7:02 ` Cristian Ciocaltea
2021-06-28 7:31 ` Manivannan Sadhasivam
2021-06-28 7:31 ` Manivannan Sadhasivam
2021-06-28 7:31 ` Manivannan Sadhasivam
2021-06-11 9:11 ` [PATCH v2 2/2] ARM: dts: owl-s500-roseapplepi: " Cristian Ciocaltea
2021-06-11 9:11 ` Cristian Ciocaltea
2021-06-14 11:27 ` Manivannan Sadhasivam [this message]
2021-06-14 11:27 ` Manivannan Sadhasivam
2021-06-14 11:28 ` [PATCH v2 0/2] Add Ethernet DTS for Actions Semi Owl S500 SoCs Manivannan Sadhasivam
2021-06-14 11:28 ` Manivannan Sadhasivam
2021-06-14 12:11 ` Cristian Ciocaltea
2021-06-14 12:11 ` Cristian Ciocaltea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210614112733.GA38584@thinkpad \
--to=mani@kernel.org \
--cc=afaerber@suse.de \
--cc=cristian.ciocaltea@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-actions@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.