[PATCH 2/2] ARM: dts: Add bcm2711-rpi-4-b-7inch-ts-dsi.dts

From: Detlev Casanova <detlev.casanova@collabora.com>
To: linux-kernel@vger.kernel.org
Cc: Detlev Casanova <detlev.casanova@collabora.com>,
	Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
	soc@kernel.org (maintainer:ARM AND ARM64 SoC SUB-ARCHITECTURES
	(COMMON PARTS)), Rob Herring <robh+dt@kernel.org>,
	Nicolas Saenz Julienne <nsaenz@kernel.org>,
	Florian Fainelli <f.fainelli@gmail.com>,
	Ray Jui <rjui@broadcom.com>,
	Scott Branden <sbranden@broadcom.com>,
	bcm-kernel-feedback-list@broadcom.com (maintainer:BROADCOM
	BCM281XX/BCM11XXX/BCM216XX ARM ARCHITE...),
	Stefan Wahren <stefan.wahren@i2se.com>,
	linux-arm-kernel@lists.infradead.org (moderated list:ARM AND
	ARM64 SoC SUB-ARCHITECTURES (COMMON PARTS)),
	devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND
	FLATTENED DEVICE TREE BINDINGS),
	linux-rpi-kernel@lists.infradead.org (moderated list:BROADCOM
	BCM2711/BCM2835 ARM ARCHITECTURE)
Subject: [PATCH 2/2] ARM: dts: Add bcm2711-rpi-4-b-7inch-ts-dsi.dts
Date: Wed,  9 Feb 2022 11:25:12 -0500	[thread overview]
Message-ID: <20220209162515.706729-3-detlev.casanova@collabora.com> (raw)
In-Reply-To: <20220209162515.706729-1-detlev.casanova@collabora.com>

Add a device tree to support the official Raspberrypi 7" touchscreen for
the Raspberry Pi 4 B

The panel is connected on the DSI 1 port and uses the simple-panel
driver.

The device tree also makes sure to activate:
 * dvp: bcm2711 clock driver
 * hvs: Hardware Video Scaler
 * pixelvalve[0-4]: CRTC modules
 * txp: CRTC Writeback

Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/bcm2711-rpi-4-b-7inch-ts-dsi.dts | 129 ++++++++++++++++++
 arch/arm64/boot/dts/broadcom/Makefile         |   1 +
 .../broadcom/bcm2711-rpi-4-b-7inch-ts-dsi.dts |   2 +
 4 files changed, 133 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm2711-rpi-4-b-7inch-ts-dsi.dts
 create mode 100644 arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b-7inch-ts-dsi.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..b46daf2df4ce 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -94,6 +94,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2837-rpi-cm3-io3.dtb \
 	bcm2711-rpi-400.dtb \
 	bcm2711-rpi-4-b.dtb \
+	bcm2711-rpi-4-b-7inch-ts-dsi.dtb \
 	bcm2711-rpi-cm4-io.dtb \
 	bcm2835-rpi-zero.dtb \
 	bcm2835-rpi-zero-w.dtb
diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b-7inch-ts-dsi.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b-7inch-ts-dsi.dts
new file mode 100644
index 000000000000..62e986358c2a
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b-7inch-ts-dsi.dts
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "bcm2711-rpi-4-b.dts"
+
+/ {
+	model = "Raspberry Pi 4 Model B + Rpi 7inch touchscreen";
+
+	panel_disp1: panel_disp1@0 {
+		reg = <0 0 0>;
+		compatible = "raspberrypi,7inch-dsi", "simple-panel";
+		backlight = <&reg_display>;
+		power-supply = <&reg_display>;
+		status = "okay";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&bridge_out>;
+			};
+		};
+	};
+
+	reg_bridge: reg_bridge@0 {
+		reg = <0 0 0>;
+		compatible = "regulator-fixed";
+		regulator-name = "bridge_reg";
+		gpio = <&reg_display 0 0>;
+		vin-supply = <&reg_display>;
+		enable-active-high;
+		status = "okay";
+	};
+};
+
+&i2c_csi_dsi {
+	ft5406: ts@38 {
+		compatible = "edt,edt-ft5506";
+		reg = <0x38>;
+		status = "okay";
+
+		vcc-supply = <&reg_display>;
+		reset-gpio = <&reg_display 1 1>;
+
+		touchscreen-size-x = < 800 >;
+		touchscreen-size-y = < 480 >;
+
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+	};
+
+	reg_display: reg_display@45 {
+		compatible = "raspberrypi,7inch-touchscreen-panel-regulator";
+		reg = <0x45>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+
+};
+
+&dsi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	port {
+		dsi_out: endpoint {
+			remote-endpoint = <&bridge_in>;
+		};
+	};
+
+	bridge@0 {
+		reg = <0>;
+		compatible = "toshiba,tc358762";
+		vddc-supply = <&reg_bridge>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in: endpoint {
+					remote-endpoint = <&dsi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				bridge_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&aon_intr {
+	status = "okay";
+};
+
+&dvp {
+	status = "okay";
+};
+
+&hvs {
+	status = "okay";
+};
+
+&pixelvalve0 {
+	status = "okay";
+};
+
+&pixelvalve1 {
+	status = "okay";
+};
+
+&pixelvalve2 {
+	status = "okay";
+};
+
+&pixelvalve3 {
+	status = "okay";
+};
+
+&pixelvalve4 {
+	status = "okay";
+};
+
+&txp {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
index c6882032a428..965361bff829 100644
--- a/arch/arm64/boot/dts/broadcom/Makefile
+++ b/arch/arm64/boot/dts/broadcom/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-400.dtb \
 			      bcm2711-rpi-4-b.dtb \
+			      bcm2711-rpi-4-b-7inch-ts-dsi.dtb \
 			      bcm2711-rpi-cm4-io.dtb \
 			      bcm2837-rpi-3-a-plus.dtb \
 			      bcm2837-rpi-3-b.dtb \
diff --git a/arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b-7inch-ts-dsi.dts b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b-7inch-ts-dsi.dts
new file mode 100644
index 000000000000..c325adc4f874
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b-7inch-ts-dsi.dts
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "arm/bcm2711-rpi-4-b-7inch-ts-dsi.dts"
-- 
2.35.1

