Re: [PATCH 2/7] dt-bindings: phy: add binding document for Allwinner F1C100s USB PHY

[Rob Herring <robh@kernel.org>]

On Wed, Jun 08, 2022 at 03:04:47PM +0800, Icenowy Zheng wrote:
> Allwinner F1C100s has the most simple USB PHY among all Allwinner SoCs,
> because it has only one OTG USB controller, no host-only OHCI/EHCI
> controllers.
> 
> Add a binding document for it.
> 
> Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
> ---
>  .../phy/allwinner,suniv-f1c100s-usb-phy.yaml  | 83 +++++++++++++++++++
>  1 file changed, 83 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml
> new file mode 100644
> index 000000000000..180fa8840bf7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml
> @@ -0,0 +1,83 @@
> +# SPDX-License-Identifier: GPL-2.0

Dual license please.

> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/allwinner,suniv-f1c100s-usb-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Allwinner F1C100s USB PHY Device Tree Bindings
> +
> +maintainers:
> +  - Chen-Yu Tsai <wens@csie.org>
> +  - Maxime Ripard <mripard@kernel.org>
> +
> +properties:
> +  "#phy-cells":
> +    const: 1
> +
> +  compatible:
> +    const: allwinner,suniv-f1c100s-usb-phy
> +
> +  reg:
> +    maxItems: 1
> +    description: PHY Control registers
> +
> +  reg-names:
> +    const: phy_ctrl
> +
> +  clocks:
> +    maxItems: 1
> +    description: USB OTG PHY bus clock
> +
> +  clock-names:
> +    const: usb0_phy

*-names is not needed with only one entry. Plus, just using the module 
name is not a great choice.

> +
> +  resets:
> +    maxItems: 1
> +    description: USB OTG reset
> +
> +  reset-names:
> +    const: usb0_reset

Same here.

> +  usb0_id_det-gpios:
> +    maxItems: 1
> +    description: GPIO to the USB OTG ID pin
> +
> +  usb0_vbus_det-gpios:
> +    maxItems: 1
> +    description: GPIO to the USB OTG VBUS detect pin
> +
> +  usb0_vbus_power-supply:
> +    description: Power supply to detect the USB OTG VBUS
> +
> +  usb0_vbus-supply:
> +    description: Regulator controlling USB OTG VBUS

Why the 'usb0_' prefix?

Are these GPIOs and Vbus supply connected to the phy? If not, these all 
belong in a connector node (as that is where they are connected to in 
h/w).

> +
> +required:
> +  - "#phy-cells"
> +  - compatible
> +  - clocks
> +  - clock-names
> +  - reg
> +  - reg-names
> +  - resets
> +  - reset-names
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/clock/suniv-f1c100s-ccu.h>
> +    #include <dt-bindings/reset/suniv-f1c100s-ccu.h>
> +
> +    phy@1c13400 {
> +        compatible = "allwinner,suniv-f1c100s-usb-phy";
> +        reg = <0x01c13400 0x10>;
> +        reg-names = "phy_ctrl";
> +        clocks = <&ccu CLK_USB_PHY0>;
> +        clock-names = "usb0_phy";
> +        resets = <&ccu RST_USB_PHY0>;
> +        reset-names = "usb0_reset";
> +        #phy-cells = <1>;
> +        usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>;
> +    };
> -- 
> 2.36.0
> 
> 

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy