[PATCH v3 1/4] dt-bindings: display: bridge: Convert cdns,dsi.txt to yaml

[Rahul T R <r-ravikumar@ti.com>]

Convert cdns,dsi.txt binding to yaml format

Signed-off-by: Rahul T R <r-ravikumar@ti.com>
---
 .../bindings/display/bridge/cdns,dsi.txt      | 112 ----------
 .../bindings/display/bridge/cdns,dsi.yaml     | 193 ++++++++++++++++++
 2 files changed, 193 insertions(+), 112 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
 create mode 100644 Documentation/devicetree/bindings/display/bridge/cdns,dsi.yaml

diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
deleted file mode 100644
index 525a4bfd8634..000000000000
--- a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
+++ /dev/null
@@ -1,112 +0,0 @@
-Cadence DSI bridge
-==================
-
-The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes.
-
-Required properties:
-- compatible: should be set to "cdns,dsi".
-- reg: physical base address and length of the controller's registers.
-- interrupts: interrupt line connected to the DSI bridge.
-- clocks: DSI bridge clocks.
-- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk".
-- phys: phandle link to the MIPI D-PHY controller.
-- phy-names: must contain "dphy".
-- #address-cells: must be set to 1.
-- #size-cells: must be set to 0.
-
-Optional properties:
-- resets: DSI reset lines.
-- reset-names: can contain "dsi_p_rst".
-
-Required subnodes:
-- ports: Ports as described in Documentation/devicetree/bindings/graph.txt.
-  2 ports are available:
-  * port 0: this port is only needed if some of your DSI devices are
-	    controlled through  an external bus like I2C or SPI. Can have at
-	    most 4 endpoints. The endpoint number is directly encoding the
-	    DSI virtual channel used by this device.
-  * port 1: represents the DPI input.
-  Other ports will be added later to support the new kind of inputs.
-
-- one subnode per DSI device connected on the DSI bus. Each DSI device should
-  contain a reg property encoding its virtual channel.
-
-Example:
-	dsi0: dsi@fd0c0000 {
-		compatible = "cdns,dsi";
-		reg = <0x0 0xfd0c0000 0x0 0x1000>;
-		clocks = <&pclk>, <&sysclk>;
-		clock-names = "dsi_p_clk", "dsi_sys_clk";
-		interrupts = <1>;
-		phys = <&dphy0>;
-		phy-names = "dphy";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@1 {
-				reg = <1>;
-				dsi0_dpi_input: endpoint {
-					remote-endpoint = <&xxx_dpi_output>;
-				};
-			};
-		};
-
-		panel: dsi-dev@0 {
-			compatible = "<vendor,panel>";
-			reg = <0>;
-		};
-	};
-
-or
-
-	dsi0: dsi@fd0c0000 {
-		compatible = "cdns,dsi";
-		reg = <0x0 0xfd0c0000 0x0 0x1000>;
-		clocks = <&pclk>, <&sysclk>;
-		clock-names = "dsi_p_clk", "dsi_sys_clk";
-		interrupts = <1>;
-		phys = <&dphy1>;
-		phy-names = "dphy";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				dsi0_output: endpoint@0 {
-					reg = <0>;
-					remote-endpoint = <&dsi_panel_input>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				dsi0_dpi_input: endpoint {
-					remote-endpoint = <&xxx_dpi_output>;
-				};
-			};
-		};
-	};
-
-	i2c@xxx {
-		panel: panel@59 {
-			compatible = "<vendor,panel>";
-			reg = <0x59>;
-
-			port {
-				dsi_panel_input: endpoint {
-					remote-endpoint = <&dsi0_output>;
-				};
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.yaml b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.yaml
new file mode 100644
index 000000000000..3da47c01dca8
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.yaml
@@ -0,0 +1,193 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/cdns,dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence DSI bridge
+
+maintainers:
+  - Boris Brezillon <boris.brezillon@bootlin.com>
+
+description: |
+   CDNS DSI is a bridge device which converts DPI to DSI
+
+properties:
+  compatible:
+    enum:
+      - cdns,dsi
+      - ti,j721e-dsi
+
+  reg:
+    minItems: 1
+    items:
+      - description:
+          Register block for controller's registers.
+      - description:
+          Register block for wrapper settings registers in case of TI J7 SoCs.
+
+  clocks:
+    items:
+      - description: PSM clock, used by the IP
+      - description: sys clock, used by the IP
+
+  clock-names:
+    items:
+      - const: dsi_p_clk
+      - const: dsi_sys_clk
+
+  phys:
+    minItems: 1
+    description: phandle link to the MIPI D-PHY controller.
+
+  phy-names:
+    const: dphy
+
+  power-domains:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  resets:
+    minItems: 1
+    description: PHY reset.
+
+  reset-names:
+    const: dsi_p_rst
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Output port representing the DSI output. It can have
+          most 4 endpoints. The endpoint number is directly encoding
+          the DSI virtual channel used by this device.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Input port representing the DP bridge input.
+
+    required:
+      - port@1
+
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - phys
+  - phy-names
+  - ports
+
+allOf:
+  - $ref: ../dsi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    dsi@fd0c0000 {
+        compatible = "cdns,dsi";
+        reg = <0x0 0xfd0c0000 0x0 0x1000>;
+        clocks = <&pclk>, <&sysclk>;
+        clock-names = "dsi_p_clk", "dsi_sys_clk";
+        interrupts = <1>;
+        phys = <&dphy0>;
+        phy-names = "dphy";
+
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@1 {
+                reg = <1>;
+                endpoint {
+                    remote-endpoint = <&xxx_dpi_output>;
+                };
+            };
+        };
+
+        panel@0 {
+            compatible = "panasonic,vvx10f034n00";
+            reg = <0>;
+            power-supply = <&vcc_lcd_reg>;
+        };
+    };
+
+  - |
+    dsi@fd0c0000 {
+        compatible = "cdns,dsi";
+        reg = <0x0 0xfd0c0000 0x0 0x1000>;
+        clocks = <&pclk>, <&sysclk>;
+        clock-names = "dsi_p_clk", "dsi_sys_clk";
+        interrupts = <1>;
+        phys = <&dphy1>;
+        phy-names = "dphy";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                dsi0_output: endpoint@0 {
+                    reg = <0>;
+                    remote-endpoint = <&dsi_panel_input>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                endpoint {
+                    remote-endpoint = <&xxx_dpi_output>;
+                };
+            };
+        };
+    };
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bridge@2d {
+            compatible = "ti,sn65dsi86";
+            reg = <0x2d>;
+
+            vpll-supply = <&src_pp1800_s4a>;
+            vccio-supply = <&src_pp1800_s4a>;
+            vcca-supply = <&src_pp1200_l2a>;
+            vcc-supply = <&src_pp1200_l2a>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    dsi_panel_input: endpoint {
+                        remote-endpoint = <&dsi0_output>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    endpoint {
+                        remote-endpoint = <&panel_in_edp>;
+                    };
+                };
+            };
+        };
+    };
-- 
2.36.1