* [PATCH v2 0/3] arm64: dts: Add InnoComm WB15-EVK support @ 2022-09-13 10:33 ` Sascha Hauer 0 siblings, 0 replies; 16+ messages in thread From: Sascha Hauer @ 2022-09-13 10:33 UTC (permalink / raw) To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer The InnoComm WB15-EVK [1] board is a Eval base board for the WB15 SoM [2] which is based on the NXP i.MX8MM. This series adds InnoComm as a vendor prefix and the necessary dts/dtsi files. Sascha [1] https://www.innocomm.com/product_inner.aspx?num=2233 [2] https://www.innocomm.com/product_inner.aspx?num=2232 Changes since v1: - Fix spelling of InnoComm: s/innocom/innocomm/ s/Innocom/InnoComm/ Sascha Hauer (3): dt-bindings: vendor-prefixes: Add prefix for InnoComm dt-bindings: arm: fsl: Add InnoComm WB15 EVK arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK .../devicetree/bindings/arm/fsl.yaml | 1 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm64/boot/dts/freescale/Makefile | 1 + .../freescale/imx8mm-innocomm-wb15-evk.dts | 147 ++++++ .../dts/freescale/imx8mm-innocomm-wb15.dtsi | 480 ++++++++++++++++++ 5 files changed, 631 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi -- 2.30.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v2 0/3] arm64: dts: Add InnoComm WB15-EVK support @ 2022-09-13 10:33 ` Sascha Hauer 0 siblings, 0 replies; 16+ messages in thread From: Sascha Hauer @ 2022-09-13 10:33 UTC (permalink / raw) To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer The InnoComm WB15-EVK [1] board is a Eval base board for the WB15 SoM [2] which is based on the NXP i.MX8MM. This series adds InnoComm as a vendor prefix and the necessary dts/dtsi files. Sascha [1] https://www.innocomm.com/product_inner.aspx?num=2233 [2] https://www.innocomm.com/product_inner.aspx?num=2232 Changes since v1: - Fix spelling of InnoComm: s/innocom/innocomm/ s/Innocom/InnoComm/ Sascha Hauer (3): dt-bindings: vendor-prefixes: Add prefix for InnoComm dt-bindings: arm: fsl: Add InnoComm WB15 EVK arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK .../devicetree/bindings/arm/fsl.yaml | 1 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm64/boot/dts/freescale/Makefile | 1 + .../freescale/imx8mm-innocomm-wb15-evk.dts | 147 ++++++ .../dts/freescale/imx8mm-innocomm-wb15.dtsi | 480 ++++++++++++++++++ 5 files changed, 631 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi -- 2.30.2 ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add prefix for InnoComm 2022-09-13 10:33 ` Sascha Hauer @ 2022-09-13 10:33 ` Sascha Hauer -1 siblings, 0 replies; 16+ messages in thread From: Sascha Hauer @ 2022-09-13 10:33 UTC (permalink / raw) To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer This adds a vendor prefix for InnoComm Mobile Technology Corp., see https://www.innocomm.com/. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- Notes: Changes since v1: - Fix spelling of InnoComm Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 2f0151e9f6bef..2ddb4778a06ad 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -601,6 +601,8 @@ patternProperties: description: Ingenic Semiconductor "^injoinic,.*": description: Injoinic Technology Corp. + "^innocomm,.*": + description: InnoComm Mobile Technology Corp. "^innolux,.*": description: Innolux Corporation "^inside-secure,.*": -- 2.30.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add prefix for InnoComm @ 2022-09-13 10:33 ` Sascha Hauer 0 siblings, 0 replies; 16+ messages in thread From: Sascha Hauer @ 2022-09-13 10:33 UTC (permalink / raw) To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer This adds a vendor prefix for InnoComm Mobile Technology Corp., see https://www.innocomm.com/. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- Notes: Changes since v1: - Fix spelling of InnoComm Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 2f0151e9f6bef..2ddb4778a06ad 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -601,6 +601,8 @@ patternProperties: description: Ingenic Semiconductor "^injoinic,.*": description: Injoinic Technology Corp. + "^innocomm,.*": + description: InnoComm Mobile Technology Corp. "^innolux,.*": description: Innolux Corporation "^inside-secure,.*": -- 2.30.2 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add prefix for InnoComm 2022-09-13 10:33 ` Sascha Hauer @ 2022-09-14 11:54 ` Rob Herring -1 siblings, 0 replies; 16+ messages in thread From: Rob Herring @ 2022-09-14 11:54 UTC (permalink / raw) To: Sascha Hauer; +Cc: kernel, devicetree, Rob Herring, linux-arm-kernel On Tue, 13 Sep 2022 12:33:35 +0200, Sascha Hauer wrote: > This adds a vendor prefix for InnoComm Mobile Technology Corp., > see https://www.innocomm.com/. > > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> > --- > > Notes: > Changes since v1: > - Fix spelling of InnoComm > > Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ > 1 file changed, 2 insertions(+) > Reviewed-by: Rob Herring <robh@kernel.org> _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add prefix for InnoComm @ 2022-09-14 11:54 ` Rob Herring 0 siblings, 0 replies; 16+ messages in thread From: Rob Herring @ 2022-09-14 11:54 UTC (permalink / raw) To: Sascha Hauer; +Cc: kernel, devicetree, Rob Herring, linux-arm-kernel On Tue, 13 Sep 2022 12:33:35 +0200, Sascha Hauer wrote: > This adds a vendor prefix for InnoComm Mobile Technology Corp., > see https://www.innocomm.com/. > > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> > --- > > Notes: > Changes since v1: > - Fix spelling of InnoComm > > Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ > 1 file changed, 2 insertions(+) > Reviewed-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v2 2/3] dt-bindings: arm: fsl: Add InnoComm WB15 EVK 2022-09-13 10:33 ` Sascha Hauer @ 2022-09-13 10:33 ` Sascha Hauer -1 siblings, 0 replies; 16+ messages in thread From: Sascha Hauer @ 2022-09-13 10:33 UTC (permalink / raw) To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer Add board compatibles for the InnoComm WB15 EVK board. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- Notes: Changes since v1: - Fix spelling of InnoComm Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 7431579ab0e85..eca63433ac057 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -831,6 +831,7 @@ properties: - gw,imx8mm-gw7901 # i.MX8MM Gateworks Board - gw,imx8mm-gw7902 # i.MX8MM Gateworks Board - gw,imx8mm-gw7903 # i.MX8MM Gateworks Board + - innocomm,wb15-evk # i.MX8MM Innocomm EVK board with WB15 SoM - kontron,imx8mm-n801x-som # i.MX8MM Kontron SL (N801X) SOM - menlo,mx8menlo # i.MX8MM Menlo board with Verdin SoM - toradex,verdin-imx8mm # Verdin iMX8M Mini Modules -- 2.30.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 2/3] dt-bindings: arm: fsl: Add InnoComm WB15 EVK @ 2022-09-13 10:33 ` Sascha Hauer 0 siblings, 0 replies; 16+ messages in thread From: Sascha Hauer @ 2022-09-13 10:33 UTC (permalink / raw) To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer Add board compatibles for the InnoComm WB15 EVK board. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- Notes: Changes since v1: - Fix spelling of InnoComm Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 7431579ab0e85..eca63433ac057 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -831,6 +831,7 @@ properties: - gw,imx8mm-gw7901 # i.MX8MM Gateworks Board - gw,imx8mm-gw7902 # i.MX8MM Gateworks Board - gw,imx8mm-gw7903 # i.MX8MM Gateworks Board + - innocomm,wb15-evk # i.MX8MM Innocomm EVK board with WB15 SoM - kontron,imx8mm-n801x-som # i.MX8MM Kontron SL (N801X) SOM - menlo,mx8menlo # i.MX8MM Menlo board with Verdin SoM - toradex,verdin-imx8mm # Verdin iMX8M Mini Modules -- 2.30.2 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: arm: fsl: Add InnoComm WB15 EVK 2022-09-13 10:33 ` Sascha Hauer @ 2022-09-14 11:54 ` Rob Herring -1 siblings, 0 replies; 16+ messages in thread From: Rob Herring @ 2022-09-14 11:54 UTC (permalink / raw) To: Sascha Hauer; +Cc: linux-arm-kernel, kernel, devicetree, Rob Herring On Tue, 13 Sep 2022 12:33:36 +0200, Sascha Hauer wrote: > Add board compatibles for the InnoComm WB15 EVK board. > > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> > --- > > Notes: > Changes since v1: > - Fix spelling of InnoComm > > Documentation/devicetree/bindings/arm/fsl.yaml | 1 + > 1 file changed, 1 insertion(+) > Acked-by: Rob Herring <robh@kernel.org> _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/3] dt-bindings: arm: fsl: Add InnoComm WB15 EVK @ 2022-09-14 11:54 ` Rob Herring 0 siblings, 0 replies; 16+ messages in thread From: Rob Herring @ 2022-09-14 11:54 UTC (permalink / raw) To: Sascha Hauer; +Cc: linux-arm-kernel, kernel, devicetree, Rob Herring On Tue, 13 Sep 2022 12:33:36 +0200, Sascha Hauer wrote: > Add board compatibles for the InnoComm WB15 EVK board. > > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> > --- > > Notes: > Changes since v1: > - Fix spelling of InnoComm > > Documentation/devicetree/bindings/arm/fsl.yaml | 1 + > 1 file changed, 1 insertion(+) > Acked-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v2 3/3] arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK 2022-09-13 10:33 ` Sascha Hauer @ 2022-09-13 10:33 ` Sascha Hauer -1 siblings, 0 replies; 16+ messages in thread From: Sascha Hauer @ 2022-09-13 10:33 UTC (permalink / raw) To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer Add the InnoComm i.MX8MM based WB15 SoM and its EVK. The WB15 is a half credit card sized board featuring: - i.MX8MM CPU - LPDDR4, 1GiB - eMMC, 8GiB - 1Gb Ethernet RGMII interface - WiFi 802.11 a/b/g/n/ac, Bluetooth 4.2 Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- Notes: Changes since v1: - Fix spelling of InnoComm arch/arm64/boot/dts/freescale/Makefile | 1 + .../freescale/imx8mm-innocomm-wb15-evk.dts | 147 ++++++ .../dts/freescale/imx8mm-innocomm-wb15.dtsi | 480 ++++++++++++++++++ 3 files changed, 628 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 8bf7f7ecebaa1..61ea927158f30 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -55,6 +55,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-innocom-wb15-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts new file mode 100644 index 0000000000000..0a28e7ceabbeb --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts @@ -0,0 +1,147 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2018 Bang & Olufsen + * Copyright 2022 Pengutronix + */ + +/dts-v1/; + +#include "imx8mm-innocomm-wb15.dtsi" + +/ { + model = "InnoComm WB15-EVK"; + compatible = "innocomm,wb15-evk", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + status = "okay"; + + led-0 { + label = "debug"; + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + reg_vsd_3v3: regulator-vsd-3v3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_vsd_3v3>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_ethphy: regulator-eth-phy { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec_phy_reg>; + regulator-name = "PHY_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec_phy>; + reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + phy-supply = <®_ethphy>; + }; + }; +}; + +&uart2 { + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + samsung,picophy-pre-emp-curr-control = <3>; + samsung,picophy-dc-vol-level-adjust = <7>; + disable-over-current; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + samsung,picophy-pre-emp-curr-control = <3>; + samsung,picophy-dc-vol-level-adjust = <7>; + disable-over-current; + status = "okay"; +}; + +&usdhc2 { + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_vsd_3v3>; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec: fecgrp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + >; + }; + + pinctrl_fec_phy: fecphygrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + >; + }; + + pinctrl_fec_phy_reg: fecphyreggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x16 + >; + }; + + pinctrl_gpio_leds: led_grp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0xd6 + >; + }; + + pinctrl_reg_vsd_3v3: reg-vsd-3v3-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi new file mode 100644 index 0000000000000..4a20508d560dd --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi @@ -0,0 +1,480 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2018 Bang & Olufsen + */ + +#include "imx8mm.dtsi" +#include <dt-bindings/phy/phy-imx8-pcie.h> + +/ { + reg_modem: regulator-modem { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_modem_regulator>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "epdev_on"; + gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_3v3_out: regulator-3v3-out { + compatible = "regulator-fixed"; + regulator-name = "3V3_OUT"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&cpu_alert0 { + temperature = <95000>; +}; + +&cpu_crit0 { + temperature = <105000>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25000000 { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-600000000 { + opp-hz = /bits/ 64 <600000000>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 GPIO_ACTIVE_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <850000>; + rohm,dvs-idle-voltage = <850000>; + rohm,dvs-suspend-voltage = <850000>; + }; + + buck2_reg: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + buck3_reg: BUCK3 { + // buck5 in datasheet + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + // buck6 in datasheet + regulator-name = "buck4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + // buck7 in datasheet + regulator-name = "buck5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + // buck8 in datasheet + regulator-name = "buck6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo6_reg: LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c2>; + pinctrl-1 = <&pinctrl_i2c2_gpio>; + scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c3>; + pinctrl-1 = <&pinctrl_i2c3_gpio>; + scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; +}; + +&pcie_phy { + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>; + fsl,tx-deemph-gen1 = <0x2d>; + fsl,tx-deemph-gen2 = <0xf>; + status = "okay"; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie0>; + reset-gpio = <&gpio5 21 GPIO_ACTIVE_LOW>; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_PHY>, + <&clk IMX8MM_CLK_PCIE1_AUX>; + clock-names = "pcie", "pcie_bus", "pcie_aux"; + fsl,max-link-speed = <1>; + assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; + assigned-clock-rates = <10000000>, <250000000>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, <&clk IMX8MM_SYS_PLL2_250M>; + status = "okay"; +}; + +&uart1 { /* BT */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clk IMX8MM_CLK_UART1>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; + fsl,uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4349-bt"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_modem_bt>; + device-wakeup-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>; + vbat-supply = <®_3v3_out>; + vddio-supply = <®_3v3_out>; + clocks = <&osc_32k>; + max-speed = <3000000>; + clock-names = "extclk"; + }; +}; + +&uart2 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&A53_1 { + cpu-supply = <&buck2_reg>; +}; + +&A53_2 { + cpu-supply = <&buck2_reg>; +}; + +&A53_3 { + cpu-supply = <&buck2_reg>; +}; + +/delete-node/ &sec_jr1; /* Job ring in use by OP-TEE */ + +&iomuxc { + pinctrl_i2c1: i2c1-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c1_gpio: i2c1-gpio-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c3 + >; + }; + + pinctrl_i2c2: i2c2-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c2_gpio: i2c2-gpio-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001c3 + >; + }; + + pinctrl_i2c3: i2c3-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3_gpio: i2c3-gpio-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001c3 + >; + }; + + pinctrl_pcie0: pcie0-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x61 + MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0x6 + >; + }; + + pinctrl_modem_bt: modembt-grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5 0x19 + MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x19 + MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 + MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19 + MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x141 + >; + }; + + pinctrl_modem_regulator: modemreg-grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x41 + >; + }; + + pinctrl_pmic: pmicirq-grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + + pinctrl_uart1: uart1-grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + MX8MM_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140 + MX8MM_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140 + >; + }; + + pinctrl_uart2: uart2-grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1-grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d0 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000194 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000196 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2-gpio-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x1d0 + >; + }; + + pinctrl_usdhc2: usdhc2-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_wdog: wdog-grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; -- 2.30.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 3/3] arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK @ 2022-09-13 10:33 ` Sascha Hauer 0 siblings, 0 replies; 16+ messages in thread From: Sascha Hauer @ 2022-09-13 10:33 UTC (permalink / raw) To: devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel, Sascha Hauer Add the InnoComm i.MX8MM based WB15 SoM and its EVK. The WB15 is a half credit card sized board featuring: - i.MX8MM CPU - LPDDR4, 1GiB - eMMC, 8GiB - 1Gb Ethernet RGMII interface - WiFi 802.11 a/b/g/n/ac, Bluetooth 4.2 Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> --- Notes: Changes since v1: - Fix spelling of InnoComm arch/arm64/boot/dts/freescale/Makefile | 1 + .../freescale/imx8mm-innocomm-wb15-evk.dts | 147 ++++++ .../dts/freescale/imx8mm-innocomm-wb15.dtsi | 480 ++++++++++++++++++ 3 files changed, 628 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 8bf7f7ecebaa1..61ea927158f30 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -55,6 +55,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-innocom-wb15-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts new file mode 100644 index 0000000000000..0a28e7ceabbeb --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15-evk.dts @@ -0,0 +1,147 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2018 Bang & Olufsen + * Copyright 2022 Pengutronix + */ + +/dts-v1/; + +#include "imx8mm-innocomm-wb15.dtsi" + +/ { + model = "InnoComm WB15-EVK"; + compatible = "innocomm,wb15-evk", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + status = "okay"; + + led-0 { + label = "debug"; + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + reg_vsd_3v3: regulator-vsd-3v3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_vsd_3v3>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_ethphy: regulator-eth-phy { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec_phy_reg>; + regulator-name = "PHY_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec_phy>; + reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + phy-supply = <®_ethphy>; + }; + }; +}; + +&uart2 { + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + samsung,picophy-pre-emp-curr-control = <3>; + samsung,picophy-dc-vol-level-adjust = <7>; + disable-over-current; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + samsung,picophy-pre-emp-curr-control = <3>; + samsung,picophy-dc-vol-level-adjust = <7>; + disable-over-current; + status = "okay"; +}; + +&usdhc2 { + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_vsd_3v3>; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec: fecgrp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + >; + }; + + pinctrl_fec_phy: fecphygrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 + >; + }; + + pinctrl_fec_phy_reg: fecphyreggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x16 + >; + }; + + pinctrl_gpio_leds: led_grp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0xd6 + >; + }; + + pinctrl_reg_vsd_3v3: reg-vsd-3v3-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi new file mode 100644 index 0000000000000..4a20508d560dd --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi @@ -0,0 +1,480 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2018 Bang & Olufsen + */ + +#include "imx8mm.dtsi" +#include <dt-bindings/phy/phy-imx8-pcie.h> + +/ { + reg_modem: regulator-modem { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_modem_regulator>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "epdev_on"; + gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_3v3_out: regulator-3v3-out { + compatible = "regulator-fixed"; + regulator-name = "3V3_OUT"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&cpu_alert0 { + temperature = <95000>; +}; + +&cpu_crit0 { + temperature = <105000>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25000000 { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100000000 { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-600000000 { + opp-hz = /bits/ 64 <600000000>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 GPIO_ACTIVE_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <850000>; + rohm,dvs-idle-voltage = <850000>; + rohm,dvs-suspend-voltage = <850000>; + }; + + buck2_reg: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + buck3_reg: BUCK3 { + // buck5 in datasheet + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + // buck6 in datasheet + regulator-name = "buck4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + // buck7 in datasheet + regulator-name = "buck5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + // buck8 in datasheet + regulator-name = "buck6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo6_reg: LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c2>; + pinctrl-1 = <&pinctrl_i2c2_gpio>; + scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c3>; + pinctrl-1 = <&pinctrl_i2c3_gpio>; + scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; +}; + +&pcie_phy { + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>; + fsl,tx-deemph-gen1 = <0x2d>; + fsl,tx-deemph-gen2 = <0xf>; + status = "okay"; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie0>; + reset-gpio = <&gpio5 21 GPIO_ACTIVE_LOW>; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_PHY>, + <&clk IMX8MM_CLK_PCIE1_AUX>; + clock-names = "pcie", "pcie_bus", "pcie_aux"; + fsl,max-link-speed = <1>; + assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; + assigned-clock-rates = <10000000>, <250000000>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, <&clk IMX8MM_SYS_PLL2_250M>; + status = "okay"; +}; + +&uart1 { /* BT */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clk IMX8MM_CLK_UART1>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; + fsl,uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4349-bt"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_modem_bt>; + device-wakeup-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>; + vbat-supply = <®_3v3_out>; + vddio-supply = <®_3v3_out>; + clocks = <&osc_32k>; + max-speed = <3000000>; + clock-names = "extclk"; + }; +}; + +&uart2 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&A53_1 { + cpu-supply = <&buck2_reg>; +}; + +&A53_2 { + cpu-supply = <&buck2_reg>; +}; + +&A53_3 { + cpu-supply = <&buck2_reg>; +}; + +/delete-node/ &sec_jr1; /* Job ring in use by OP-TEE */ + +&iomuxc { + pinctrl_i2c1: i2c1-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c1_gpio: i2c1-gpio-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c3 + >; + }; + + pinctrl_i2c2: i2c2-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c2_gpio: i2c2-gpio-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001c3 + >; + }; + + pinctrl_i2c3: i2c3-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3_gpio: i2c3-gpio-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001c3 + >; + }; + + pinctrl_pcie0: pcie0-grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B 0x61 + MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0x6 + >; + }; + + pinctrl_modem_bt: modembt-grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5 0x19 + MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x19 + MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 + MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19 + MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x141 + >; + }; + + pinctrl_modem_regulator: modemreg-grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x41 + >; + }; + + pinctrl_pmic: pmicirq-grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + + pinctrl_uart1: uart1-grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + MX8MM_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140 + MX8MM_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140 + >; + }; + + pinctrl_uart2: uart2-grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1-grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d0 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000194 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000196 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6 + MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196 + MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2-gpio-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x1d0 + >; + }; + + pinctrl_usdhc2: usdhc2-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_wdog: wdog-grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; -- 2.30.2 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK 2022-09-13 10:33 ` Sascha Hauer @ 2022-09-15 2:47 ` kernel test robot -1 siblings, 0 replies; 16+ messages in thread From: kernel test robot @ 2022-09-15 2:47 UTC (permalink / raw) To: Sascha Hauer, devicetree Cc: kbuild-all, Rob Herring, linux-arm-kernel, kernel, Sascha Hauer Hi Sascha, I love your patch! Yet something to improve: [auto build test ERROR on robh/for-next] [also build test ERROR on linus/master v6.0-rc5] [cannot apply to next-20220914] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Sascha-Hauer/arm64-dts-Add-InnoComm-WB15-EVK-support/20220913-183559 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm64-allyesconfig (https://download.01.org/0day-ci/archive/20220915/202209151014.DmoRoYFo-lkp@intel.com/config) compiler: aarch64-linux-gcc (GCC) 12.1.0 reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # https://github.com/intel-lab-lkp/linux/commit/1d6fe7241418270e6c26852e85104d10141c8678 git remote add linux-review https://github.com/intel-lab-lkp/linux git fetch --no-tags linux-review Sascha-Hauer/arm64-dts-Add-InnoComm-WB15-EVK-support/20220913-183559 git checkout 1d6fe7241418270e6c26852e85104d10141c8678 # save the config file mkdir build_dir && cp config build_dir/.config COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=arm64 SHELL=/bin/bash If you fix the issue, kindly add following tag where applicable Reported-by: kernel test robot <lkp@intel.com> All errors (new ones prefixed by >>): >> make[3]: *** No rule to make target 'arch/arm64/boot/dts/freescale/imx8mm-innocom-wb15-evk.dtb', needed by '__build'. make[3]: Target '__build' not remade because of errors. -- 0-DAY CI Kernel Test Service https://01.org/lkp _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK @ 2022-09-15 2:47 ` kernel test robot 0 siblings, 0 replies; 16+ messages in thread From: kernel test robot @ 2022-09-15 2:47 UTC (permalink / raw) To: Sascha Hauer, devicetree Cc: kbuild-all, Rob Herring, linux-arm-kernel, kernel, Sascha Hauer Hi Sascha, I love your patch! Yet something to improve: [auto build test ERROR on robh/for-next] [also build test ERROR on linus/master v6.0-rc5] [cannot apply to next-20220914] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Sascha-Hauer/arm64-dts-Add-InnoComm-WB15-EVK-support/20220913-183559 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm64-allyesconfig (https://download.01.org/0day-ci/archive/20220915/202209151014.DmoRoYFo-lkp@intel.com/config) compiler: aarch64-linux-gcc (GCC) 12.1.0 reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # https://github.com/intel-lab-lkp/linux/commit/1d6fe7241418270e6c26852e85104d10141c8678 git remote add linux-review https://github.com/intel-lab-lkp/linux git fetch --no-tags linux-review Sascha-Hauer/arm64-dts-Add-InnoComm-WB15-EVK-support/20220913-183559 git checkout 1d6fe7241418270e6c26852e85104d10141c8678 # save the config file mkdir build_dir && cp config build_dir/.config COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=arm64 SHELL=/bin/bash If you fix the issue, kindly add following tag where applicable Reported-by: kernel test robot <lkp@intel.com> All errors (new ones prefixed by >>): >> make[3]: *** No rule to make target 'arch/arm64/boot/dts/freescale/imx8mm-innocom-wb15-evk.dtb', needed by '__build'. make[3]: Target '__build' not remade because of errors. -- 0-DAY CI Kernel Test Service https://01.org/lkp ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK 2022-09-13 10:33 ` Sascha Hauer @ 2022-09-15 15:21 ` Krzysztof Kozlowski -1 siblings, 0 replies; 16+ messages in thread From: Krzysztof Kozlowski @ 2022-09-15 15:21 UTC (permalink / raw) To: Sascha Hauer, devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel On 13/09/2022 11:33, Sascha Hauer wrote: > Add the InnoComm i.MX8MM based WB15 SoM and its EVK. The WB15 is a > half credit card sized board featuring: > > - i.MX8MM CPU > - LPDDR4, 1GiB > - eMMC, 8GiB > - 1Gb Ethernet RGMII interface > - WiFi 802.11 a/b/g/n/ac, Bluetooth 4.2 > > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Thank you for your patch. There is something to discuss/improve. > + pinctrl_fec: fecgrp { > + fsl,pins = < > + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 > + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 > + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f > + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f > + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f > + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f > + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 > + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 > + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 > + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 > + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f > + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 > + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 > + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f > + >; > + }; > + > + pinctrl_fec_phy: fecphygrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 > + >; > + }; > + > + pinctrl_fec_phy_reg: fecphyreggrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x16 > + >; > + }; > + > + pinctrl_gpio_leds: led_grp { No underscores in node names. > + fsl,pins = < > + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0xd6 > + >; > + }; > + > + pinctrl_reg_vsd_3v3: reg-vsd-3v3-grp { > + fsl,pins = < > + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi > new file mode 100644 > index 0000000000000..4a20508d560dd > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi > @@ -0,0 +1,480 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2018 Bang & Olufsen > + */ > + > +#include "imx8mm.dtsi" > +#include <dt-bindings/phy/phy-imx8-pcie.h> > + > +/ { > + reg_modem: regulator-modem { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_modem_regulator>; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "epdev_on"; > + gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; > + }; > + > + reg_3v3_out: regulator-3v3-out { > + compatible = "regulator-fixed"; > + regulator-name = "3V3_OUT"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > +}; > + > +&cpu_alert0 { > + temperature = <95000>; > +}; > + > +&cpu_crit0 { > + temperature = <105000>; > +}; > + > +&ddrc { > + operating-points-v2 = <&ddrc_opp_table>; > + > + ddrc_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-25000000 { > + opp-hz = /bits/ 64 <25000000>; > + }; > + > + opp-100000000 { > + opp-hz = /bits/ 64 <100000000>; > + }; > + > + opp-600000000 { > + opp-hz = /bits/ 64 <600000000>; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default", "gpio"; > + pinctrl-0 = <&pinctrl_i2c1>; > + pinctrl-1 = <&pinctrl_i2c1_gpio>; > + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + status = "okay"; > + > + pmic@4b { > + compatible = "rohm,bd71847"; > + reg = <0x4b>; > + pinctrl-0 = <&pinctrl_pmic>; > + interrupt-parent = <&gpio1>; > + interrupts = <3 GPIO_ACTIVE_LOW>; Wrong flag. This is very old bug. Please base your work on recent DTSes. Don't start with vendor/downstream DTS because it contains bugs. Instead take recent mainline and customize it for the manufacturer. > + rohm,reset-snvs-powered; > + Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 3/3] arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK @ 2022-09-15 15:21 ` Krzysztof Kozlowski 0 siblings, 0 replies; 16+ messages in thread From: Krzysztof Kozlowski @ 2022-09-15 15:21 UTC (permalink / raw) To: Sascha Hauer, devicetree; +Cc: Rob Herring, linux-arm-kernel, kernel On 13/09/2022 11:33, Sascha Hauer wrote: > Add the InnoComm i.MX8MM based WB15 SoM and its EVK. The WB15 is a > half credit card sized board featuring: > > - i.MX8MM CPU > - LPDDR4, 1GiB > - eMMC, 8GiB > - 1Gb Ethernet RGMII interface > - WiFi 802.11 a/b/g/n/ac, Bluetooth 4.2 > > Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Thank you for your patch. There is something to discuss/improve. > + pinctrl_fec: fecgrp { > + fsl,pins = < > + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x03 > + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x03 > + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f > + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f > + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f > + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f > + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 > + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 > + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 > + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 > + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f > + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 > + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 > + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f > + >; > + }; > + > + pinctrl_fec_phy: fecphygrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 > + >; > + }; > + > + pinctrl_fec_phy_reg: fecphyreggrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x16 > + >; > + }; > + > + pinctrl_gpio_leds: led_grp { No underscores in node names. > + fsl,pins = < > + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0xd6 > + >; > + }; > + > + pinctrl_reg_vsd_3v3: reg-vsd-3v3-grp { > + fsl,pins = < > + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi > new file mode 100644 > index 0000000000000..4a20508d560dd > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi > @@ -0,0 +1,480 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2018 Bang & Olufsen > + */ > + > +#include "imx8mm.dtsi" > +#include <dt-bindings/phy/phy-imx8-pcie.h> > + > +/ { > + reg_modem: regulator-modem { > + compatible = "regulator-fixed"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_modem_regulator>; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "epdev_on"; > + gpio = <&gpio3 16 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-always-on; > + }; > + > + reg_3v3_out: regulator-3v3-out { > + compatible = "regulator-fixed"; > + regulator-name = "3V3_OUT"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > +}; > + > +&cpu_alert0 { > + temperature = <95000>; > +}; > + > +&cpu_crit0 { > + temperature = <105000>; > +}; > + > +&ddrc { > + operating-points-v2 = <&ddrc_opp_table>; > + > + ddrc_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-25000000 { > + opp-hz = /bits/ 64 <25000000>; > + }; > + > + opp-100000000 { > + opp-hz = /bits/ 64 <100000000>; > + }; > + > + opp-600000000 { > + opp-hz = /bits/ 64 <600000000>; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default", "gpio"; > + pinctrl-0 = <&pinctrl_i2c1>; > + pinctrl-1 = <&pinctrl_i2c1_gpio>; > + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + status = "okay"; > + > + pmic@4b { > + compatible = "rohm,bd71847"; > + reg = <0x4b>; > + pinctrl-0 = <&pinctrl_pmic>; > + interrupt-parent = <&gpio1>; > + interrupts = <3 GPIO_ACTIVE_LOW>; Wrong flag. This is very old bug. Please base your work on recent DTSes. Don't start with vendor/downstream DTS because it contains bugs. Instead take recent mainline and customize it for the manufacturer. > + rohm,reset-snvs-powered; > + Best regards, Krzysztof ^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2022-09-15 15:23 UTC | newest] Thread overview: 16+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2022-09-13 10:33 [PATCH v2 0/3] arm64: dts: Add InnoComm WB15-EVK support Sascha Hauer 2022-09-13 10:33 ` Sascha Hauer 2022-09-13 10:33 ` [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add prefix for InnoComm Sascha Hauer 2022-09-13 10:33 ` Sascha Hauer 2022-09-14 11:54 ` Rob Herring 2022-09-14 11:54 ` Rob Herring 2022-09-13 10:33 ` [PATCH v2 2/3] dt-bindings: arm: fsl: Add InnoComm WB15 EVK Sascha Hauer 2022-09-13 10:33 ` Sascha Hauer 2022-09-14 11:54 ` Rob Herring 2022-09-14 11:54 ` Rob Herring 2022-09-13 10:33 ` [PATCH v2 3/3] arm64: dts: freescale: Add InnoComm i.MX8MM based WB15 SoM and EVK Sascha Hauer 2022-09-13 10:33 ` Sascha Hauer 2022-09-15 2:47 ` kernel test robot 2022-09-15 2:47 ` kernel test robot 2022-09-15 15:21 ` Krzysztof Kozlowski 2022-09-15 15:21 ` Krzysztof Kozlowski
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.