Re: [PATCH 1/6] dt-bindings: usb: ci-hdrc-usb2: convert to yaml

[Rob Herring <robh@kernel.org>]

On Mon, Oct 10, 2022 at 06:18:11PM +0800, Peng Fan (OSS) wrote:
> From: Peng Fan <peng.fan@nxp.com>
> 
> Convert the binding to yaml format

s/yaml/DT schema/

> 
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> ---
>  .../devicetree/bindings/usb/ci-hdrc-usb2.txt  | 158 ---------
>  .../devicetree/bindings/usb/ci-hdrc-usb2.yaml | 306 ++++++++++++++++++
>  2 files changed, 306 insertions(+), 158 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
>  create mode 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml

> diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml
> new file mode 100644
> index 000000000000..1c10691c45f2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml
> @@ -0,0 +1,306 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: USB2 ChipIdea USB controller for ci13xxx Binding
> +
> +maintainers:
> +  - Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> +
> +properties:
> +  compatible:
> +    oneOf:
> +      - enum:
> +          - chipidea,usb2
> +          - lsi,zevio-usb
> +          - nvidia,tegra20-udc
> +          - nvidia,tegra30-udc
> +          - nvidia,tegra114-udc
> +          - nvidia,tegra124-udc
> +          - qcom,ci-hdrc
> +      - items:
> +          - enum:
> +              - fsl,imx23-usb
> +              - fsl,imx25-usb
> +              - fsl,imx28-usb
> +              - fsl,imx6q-usb
> +              - fsl,imx6sl-usb
> +              - fsl,imx6sx-usb
> +              - fsl,imx6ul-usb
> +              - fsl,imx7d-usb
> +          - const: fsl,imx27-usb
> +      - items:
> +          - const: fsl,imx7ulp-usb
> +          - const: fsl,imx6ul-usb
> +      - items:
> +          - const: lsi,zevio-usb
> +      - items:
> +          - const: xlnx,zynq-usb-2.20a
> +          - const: chipidea,usb2
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +  
> +  clocks:
> +    maxItems: 2
> +
> +  itc-setting:
> +    description:
> +      interrupt threshold control register control, the setting should be
> +      aligned with ITC bits at register USBCMD.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  ahb-burst-config:
> +    description:
> +      it is vendor dependent, the required value should be aligned with
> +      AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is
> +      used to change AHB burst configuration, check the chipidea spec for
> +      meaning of each value. If this property is not existed, it will use
> +      the reset value.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    minimum: 0x0
> +    maximum: 0x7
> +
> +  tx-burst-size-dword:
> +    description:
> +      it is vendor dependent, the tx burst size in dword (4 bytes), This
> +      register represents the maximum length of a the burst in 32-bit
> +      words while moving data from system memory to the USB bus, the value
> +      of this property will only take effect if property "ahb-burst-config"
> +      is set to 0, if this property is missing the reset default of the
> +      hardware implementation will be used.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  rx-burst-size-dword:
> +    description:
> +      it is vendor dependent, the rx burst size in dword (4 bytes), This
> +      register represents the maximum length of a the burst in 32-bit words
> +      while moving data from the USB bus to system memory, the value of
> +      this property will only take effect if property "ahb-burst-config"
> +      is set to 0, if this property is missing the reset default of the
> +      hardware implementation will be used.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  extcon:
> +    description: |
> +      Phandles to external connector devices. First phandle should point
> +      to external connector, which provide "USB" cable events, the second
> +      should point to external connector device, which provide "USB-HOST"
> +      cable events. If one of the external connector devices is not
> +      required, empty <0> phandle should be specified.
> +
> +  phy-clkgate-delay-us:
> +    description: |
> +      The delay time (us) between putting the PHY into low power mode and
> +      gating the PHY clock.
> +
> +  non-zero-ttctrl-ttha:
> +    description: |
> +      After setting this property, the value of register ttctrl.ttha
> +      will be 0x7f; if not, the value will be 0x0, this is the default
> +      value. It needs to be very carefully for setting this property, it
> +      is recommended that consult with your IC engineer before setting
> +      this value.  On the most of chipidea platforms, the "usage_tt" flag
> +      at RTL is 0, so this property only affects siTD.
> +
> +      If this property is not set, the max packet size is 1023 bytes, and
> +      if the total of packet size for pervious transactions are more than
> +      256 bytes, it can't accept any transactions within this frame. The
> +      use case is single transaction, but higher frame rate.
> +
> +      If this property is set, the max packet size is 188 bytes, it can
> +      handle more transactions than above case, it can accept transactions
> +      until it considers the left room size within frame is less than 188
> +      bytes, software needs to make sure it does not send more than 90%
> +      maximum_periodic_data_per_frame. The use case is multiple
> +      transactions, but less frame rate.
> +
> +  mux-controls:
> +    description: |
> +      The mux control for toggling host/device output of this controller.
> +      It's expected that a mux state of 0 indicates device mode and a mux
> +      state of 1 indicates host mode.
> +
> +  mux-control-names:
> +    description: Shall be "usb_switch" if mux-controls is specified.
> +
> +  pinctrl-names:
> +    description: |
> +      Names for optional pin modes in "default", "host", "device".
> +      In case of HSIC-mode, "idle" and "active" pin modes are mandatory.
> +      In this case, the "idle" state needs to pull down the data and
> +      strobe pin and the "active" state needs to pull up the strobe pin.
> +
> +  pinctrl-0:
> +    maxItems: 1
> +
> +  pinctrl-1:
> +    maxItems: 1
> +
> +  phys:
> +    maxItems: 1
> +
> +  phy-names:
> +    const: usb-phy
> +
> +  vbus-supply:
> +    description: reference to the VBUS regulator.
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +
> +allOf:
> +  - $ref: usb-drd.yaml#
> +  - $ref: usb-hcd.yaml#
> +  - if:
> +      properties:
> +        mux-controls:
> +          true
> +    then:
> +      properties:
> +        mux-control-names:
> +          const: usb_switch
> +  - if:
> +      properties:
> +        phy_type:
> +          const: hsic
> +
> +      required:
> +        - phy_type
> +    then:
> +      properties:
> +        pinctrl-names:
> +          items:
> +            - const: idle
> +            - const: active
> +    else:
> +      properties:
> +        pinctrl-names:
> +          oneOf:
> +            - items:
> +                - const: default
> +                - enum:
> +                    - host
> +                    - device
> +            - items:
> +                - const: default
> +  - if:
> +      properties:
> +        compatible:
> +          enum:
> +            - fsl,imx23-usb
> +            - fsl,imx25-usb
> +            - fsl,imx27-usb
> +            - fsl,imx28-usb
> +            - fsl,imx6q-usb
> +            - fsl,imx6sl-usb
> +            - fsl,imx6sx-usb
> +            - fsl,imx6ul-usb
> +            - fsl,imx7d-usb
> +            - fsl,imx7ulp-usb
> +    then:
> +      properties:
> +        fsl,usbmisc: 
> +          description:
> +            Phandler of non-core register device, with one argument that
> +            indicate usb controller index

type ref?

Don't define properties within if/then/else. Define at top level and 
then restrict presence in the if/then schema.

> +
> +        disable-over-current:
> +          description: disable over current detect
> +
> +        over-current-active-low:
> +          description: over current signal polarity is active low
> +
> +        over-current-active-high:
> +          description: |
> +            Over current signal polarity is active high. It's recommended to
> +            specify the over current polarity.
> +
> +        power-active-high:
> +          description: power signal polarity is active high
> +
> +        external-vbus-divider:
> +          description: enables off-chip resistor divider for Vbus
> +
> +        samsung,picophy-pre-emp-curr-control:
> +          description: |
> +            HS Transmitter Pre-Emphasis Current Control. This signal controls
> +            the amount of current sourced to the USB_OTG*_DP and USB_OTG*_DN
> +            pins after a J-to-K or K-to-J transition. The range is from 0x0 to
> +            0x3, the default value is 0x1. Details can refer to TXPREEMPAMPTUNE0
> +            bits of USBNC_n_PHY_CFG1.
> +          $ref: /schemas/types.yaml#/definitions/uint32
> +          minimum: 0x0
> +          maximum: 0x3
> +
> +        samsung,picophy-dc-vol-level-adjust:
> +          description: |
> +            HS DC Voltage Level Adjustment. Adjust the high-speed transmitter DC
> +            level voltage. The range is from 0x0 to 0xf, the default value is
> +            0x3. Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1.
> +          $ref: /schemas/types.yaml#/definitions/uint32
> +          minimum: 0x0
> +          maximum: 0xf
> +
> +additionalProperties: true

Cannot be true.

> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/clock/berlin2.h>
> +
> +    usb@f7ed0000 {
> +        compatible = "chipidea,usb2";

Doesn't match documentation. You should know by now to test your 
bindings.

> +        reg = <0xf7ed0000 0x10000>;
> +        interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +        clocks = <&chip CLKID_USB0>;
> +        phys = <&usb_phy0>;
> +        phy-names = "usb-phy";
> +        vbus-supply = <&reg_usb0_vbus>;
> +        itc-setting = <0x4>; /* 4 micro-frames */
> +         /* Incremental burst of unspecified length */
> +        ahb-burst-config = <0x0>;
> +        tx-burst-size-dword = <0x10>; /* 64 bytes */
> +        rx-burst-size-dword = <0x10>;
> +        extcon = <0>, <&usb_id>;
> +        phy-clkgate-delay-us = <400>;
> +        mux-controls = <&usb_switch>;
> +        mux-control-names = "usb_switch";
> +    };
> +
> +  # Example for HSIC:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/clock/imx6qdl-clock.h>
> +
> +    usb@2184400 {
> +        compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
> +        reg = <0x02184400 0x200>;
> +        interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
> +        clocks = <&clks IMX6QDL_CLK_USBOH3>;
> +        fsl,usbphy = <&usbphynop1>;
> +        fsl,usbmisc = <&usbmisc 2>;
> +        phy_type = "hsic";
> +        dr_mode = "host";
> +        ahb-burst-config = <0x0>;
> +        tx-burst-size-dword = <0x10>;
> +        rx-burst-size-dword = <0x10>;
> +        pinctrl-names = "idle", "active";
> +        pinctrl-0 = <&pinctrl_usbh2_idle>;
> +        pinctrl-1 = <&pinctrl_usbh2_active>;
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +        
> +        usbnet: ethernet@1 {
> +            compatible = "usb424,9730";
> +            reg = <1>;
> +        };
> +    };
> +
> +...
> -- 
> 2.37.1
> 
>