[PATCH v3 00/18] arm64: dts: qcom: sa8775p: add basic PMIC support

[PATCH v3 00/18] arm64: dts: qcom: sa8775p: add basic PMIC support

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

This adds support for a number of PMIC functionalities on sa8775p. The PMIC
used on the reference board is pm8654au which is another variant of the SPMI
PMIC from Qualcomm with an automotive twist.

v2 -> v3:
- add GPIO line names for the PMIC GPIOs on sa8775p-ride
- add missing GPIO chips to the PMIC .dtsi
- add missing thermal zones and alerts
- add regulators (driver support and regulator settings for sa8775p-ride)
- add missing PDC mappings
- squash patches 7 and 8 to avoid adding code without users
- dropped Krzysztof's Ack from patch 3 as it now extends the max number of
  mappings so most likely needs a second look

v1 -> v2:
- improve DT coding style where needed
- don't disable the power button in PMIC's .dtsi
- add debounce time for pwrkey and resin inputs
- use the official PMIC's name in DT labels
- add reg-names property for the PON node
- add patches that tidy up the dtsi before the PMIC stuff

Bartosz Golaszewski (18):
  arm64: dts: qcom: sa8775p: pad reg properties to 8 digits
  arm64: dts: qcom: sa8775p: sort soc nodes by reg property
  dt-bindings: interrupt-controller: qcom-pdc: add compatible for
    sa8775p
  arm64: dts: qcom: sa8775p: add the pdc node
  arm64: dts: qcom: sa8775p: add the spmi node
  dt-bindings: mfd: qcom,spmi-pmic: add compatible for pmm8654au
  arm64: dts: qcom: sa8775p: add support for the on-board PMICs
  arm64: dts: qcom: sa8775p: add the Power On device node
  arm64: dts: qcom: sa8775p: pmic: add the power key
  arm64: dts: qcom: sa8775p: pmic: add support for the pmm8654 RESIN
    input
  arm64: dts: qcom: sa8775p: pmic: add thermal zones
  dt-bindings: pinctrl: qcom,pmic-gpio: add compatible for
    pmm8654au-gpio
  pinctrl: qcom: spmi-gpio: add support for pmm8654au-gpio
  arm64: dts: qcom: sa8775p: add PMIC GPIO controller nodes
  arm64: dts: qcom: sa8775p-ride: set gpio-line-names for PMIC GPIOs
  dt-bindings: regulator: qcom,rpmh: add compatible for pmm8654au RPMH
  regulator: qcom-rpmh: add support for pmm8654au regulators
  arm64: dts: qcom: sa8775p-ride: add PMIC regulators

 .../interrupt-controller/qcom,pdc.yaml        |   3 +-
 .../bindings/mfd/qcom,spmi-pmic.yaml          |   1 +
 .../bindings/pinctrl/qcom,pmic-gpio.yaml      |   2 +
 .../regulator/qcom,rpmh-regulator.yaml        |  14 +
 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi   | 211 ++++++++
 arch/arm64/boot/dts/qcom/sa8775p-ride.dts     | 285 +++++++++++
 arch/arm64/boot/dts/qcom/sa8775p.dtsi         | 465 ++++++++++--------
 drivers/pinctrl/qcom/pinctrl-spmi-gpio.c      |   1 +
 drivers/regulator/qcom-rpmh-regulator.c       |  55 +++
 9 files changed, 838 insertions(+), 199 deletions(-)
 create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi

-- 
2.37.2

[PATCH v3 01/18] arm64: dts: qcom: sa8775p: pad reg properties to 8 digits

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

The file has inconsistent padding of the address part of soc node
children's reg properties. Fix it.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index c5b73c591e0f..5aa28a3b12ae 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -440,7 +440,7 @@ soc: soc@0 {
 
 		gcc: clock-controller@100000 {
 			compatible = "qcom,sa8775p-gcc";
-			reg = <0x0 0x100000 0x0 0xc7018>;
+			reg = <0x0 0x00100000 0x0 0xc7018>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
@@ -464,7 +464,7 @@ gcc: clock-controller@100000 {
 
 		ipcc: mailbox@408000 {
 			compatible = "qcom,sa8775p-ipcc", "qcom,ipcc";
-			reg = <0x0 0x408000 0x0 0x1000>;
+			reg = <0x0 0x00408000 0x0 0x1000>;
 			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <3>;
@@ -473,7 +473,7 @@ ipcc: mailbox@408000 {
 
 		qupv3_id_1: geniqup@ac0000 {
 			compatible = "qcom,geni-se-qup";
-			reg = <0x0 0xac0000 0x0 0x6000>;
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
@@ -485,7 +485,7 @@ qupv3_id_1: geniqup@ac0000 {
 
 			uart10: serial@a8c000 {
 				compatible = "qcom,geni-uart";
-				reg = <0x0 0xa8c000 0x0 0x4000>;
+				reg = <0x0 0x00a8c000 0x0 0x4000>;
 				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
@@ -735,7 +735,7 @@ rpmhpd_opp_turbo_l1: opp-9 {
 
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
-			reg = <0x0 0x1f40000 0x0 0x20000>;
+			reg = <0x0 0x01f40000 0x0 0x20000>;
 			#hwlock-cells = <1>;
 		};
 
@@ -754,7 +754,7 @@ cpufreq_hw: cpufreq@18591000 {
 
 		tlmm: pinctrl@f000000 {
 			compatible = "qcom,sa8775p-tlmm";
-			reg = <0x0 0xf000000 0x0 0x1000000>;
+			reg = <0x0 0x0f000000 0x0 0x1000000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
 			#gpio-cells = <2>;
-- 
2.37.2

[PATCH v3 02/18] arm64: dts: qcom: sa8775p: sort soc nodes by reg property

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Sort all children of the soc node by the first address in their reg
property. This was mostly already the case but there were some nodes
that didn't follow it so fix it now for consistency.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p.dtsi | 394 +++++++++++++-------------
 1 file changed, 197 insertions(+), 197 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index 5aa28a3b12ae..296ba69b81ab 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -471,50 +471,6 @@ ipcc: mailbox@408000 {
 			#mbox-cells = <2>;
 		};
 
-		qupv3_id_1: geniqup@ac0000 {
-			compatible = "qcom,geni-se-qup";
-			reg = <0x0 0x00ac0000 0x0 0x6000>;
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
-			clock-names = "m-ahb", "s-ahb";
-			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
-				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
-			iommus = <&apps_smmu 0x443 0x0>;
-			status = "disabled";
-
-			uart10: serial@a8c000 {
-				compatible = "qcom,geni-uart";
-				reg = <0x0 0x00a8c000 0x0 0x4000>;
-				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
-				clock-names = "se";
-				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
-				interconnect-names = "qup-core", "qup-config";
-				interconnects = <&clk_virt MASTER_QUP_CORE_1 0
-						 &clk_virt SLAVE_QUP_CORE_1 0>,
-						<&gem_noc MASTER_APPSS_PROC 0
-						 &config_noc SLAVE_QUP_1 0>;
-				power-domains = <&rpmhpd SA8775P_CX>;
-				operating-points-v2 = <&qup_opp_table_100mhz>;
-				status = "disabled";
-			};
-
-			uart12: serial@a94000 {
-				compatible = "qcom,geni-uart";
-				reg = <0x0 0x00a94000 0x0 0x4000>;
-				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
-				clock-names = "se";
-				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
-						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
-						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
-						 &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
-				interconnect-names = "qup-core", "qup-config";
-				power-domains = <&rpmhpd SA8775P_CX>;
-				status = "disabled";
-			};
-		};
-
 		qupv3_id_2: geniqup@8c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0x0 0x008c0000 0x0 0x6000>;
@@ -585,173 +541,56 @@ &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>,
 			};
 		};
 
-		intc: interrupt-controller@17a00000 {
-			compatible = "arm,gic-v3";
-			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
-			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
-			#redistributor-regions = <1>;
-			redistributor-stride = <0x0 0x20000>;
-		};
-
-		memtimer: timer@17c20000 {
-			compatible = "arm,armv7-timer-mem";
-			reg = <0x0 0x17c20000 0x0 0x1000>;
-			ranges = <0x0 0x0 0x0 0x20000000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			frame@17c21000 {
-				reg = <0x17c21000 0x1000>,
-				      <0x17c22000 0x1000>;
-				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				frame-number = <0>;
-			};
-
-			frame@17c23000 {
-				reg = <0x17c23000 0x1000>;
-				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				frame-number = <1>;
-				status = "disabled";
-			};
-
-			frame@17c25000 {
-				reg = <0x17c25000 0x1000>;
-				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				frame-number = <2>;
-				status = "disabled";
-			};
-
-			frame@17c27000 {
-				reg = <0x17c27000 0x1000>;
-				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				frame-number = <3>;
-				status = "disabled";
-			};
-
-			frame@17c29000 {
-				reg = <0x17c29000 0x1000>;
-				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				frame-number = <4>;
-				status = "disabled";
-			};
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x443 0x0>;
+			status = "disabled";
 
-			frame@17c2b000 {
-				reg = <0x17c2b000 0x1000>;
-				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				frame-number = <5>;
+			uart10: serial@a8c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00a8c000 0x0 0x4000>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				interconnect-names = "qup-core", "qup-config";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0
+						 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0
+						 &config_noc SLAVE_QUP_1 0>;
+				power-domains = <&rpmhpd SA8775P_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
 				status = "disabled";
 			};
 
-			frame@17c2d000 {
-				reg = <0x17c2d000 0x1000>;
-				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				frame-number = <6>;
+			uart12: serial@a94000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00a94000 0x0 0x4000>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
 				status = "disabled";
 			};
 		};
 
-		apps_rsc: rsc@18200000 {
-			compatible = "qcom,rpmh-rsc";
-			reg = <0x0 0x18200000 0x0 0x10000>,
-			      <0x0 0x18210000 0x0 0x10000>,
-			      <0x0 0x18220000 0x0 0x10000>;
-			reg-names = "drv-0", "drv-1", "drv-2";
-			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-			      <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-			      <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
-			qcom,tcs-offset = <0xd00>;
-			qcom,drv-id = <2>;
-			qcom,tcs-config = <ACTIVE_TCS 2>,
-					  <SLEEP_TCS 3>,
-					  <WAKE_TCS 3>,
-					  <CONTROL_TCS 0>;
-			label = "apps_rsc";
-
-			apps_bcm_voter: bcm-voter {
-				compatible = "qcom,bcm-voter";
-			};
-
-			rpmhcc: clock-controller {
-				compatible = "qcom,sa8775p-rpmh-clk";
-				#clock-cells = <1>;
-				clock-names = "xo";
-				clocks = <&xo_board_clk>;
-			};
-
-			rpmhpd: power-controller {
-				compatible = "qcom,sa8775p-rpmhpd";
-				#power-domain-cells = <1>;
-				operating-points-v2 = <&rpmhpd_opp_table>;
-
-				rpmhpd_opp_table: opp-table {
-					compatible = "operating-points-v2";
-
-					rpmhpd_opp_ret: opp-0 {
-						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
-					};
-
-					rpmhpd_opp_min_svs: opp-1 {
-						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
-					};
-
-					rpmhpd_opp_low_svs: opp2 {
-						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
-					};
-
-					rpmhpd_opp_svs: opp3 {
-						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
-					};
-
-					rpmhpd_opp_svs_l1: opp-4 {
-						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
-					};
-
-					rpmhpd_opp_nom: opp-5 {
-						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
-					};
-
-					rpmhpd_opp_nom_l1: opp-6 {
-						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
-					};
-
-					rpmhpd_opp_nom_l2: opp-7 {
-						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
-					};
-
-					rpmhpd_opp_turbo: opp-8 {
-						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
-					};
-
-					rpmhpd_opp_turbo_l1: opp-9 {
-						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
-					};
-				};
-			};
-		};
-
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0x0 0x01f40000 0x0 0x20000>;
 			#hwlock-cells = <1>;
 		};
 
-		cpufreq_hw: cpufreq@18591000 {
-			compatible = "qcom,sa8775p-cpufreq-epss",
-				     "qcom,cpufreq-epss";
-			reg = <0x0 0x18591000 0x0 0x1000>,
-			      <0x0 0x18593000 0x0 0x1000>;
-			reg-names = "freq-domain0", "freq-domain1";
-
-			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
-			clock-names = "xo", "alternate";
-
-			#freq-domain-cells = <1>;
-		};
-
 		tlmm: pinctrl@f000000 {
 			compatible = "qcom,sa8775p-tlmm";
 			reg = <0x0 0x0f000000 0x0 0x1000000>;
@@ -900,6 +739,167 @@ apps_smmu: iommu@15000000 {
 				     <GIC_SPI 892 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 891 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		intc: interrupt-controller@17a00000 {
+			compatible = "arm,gic-v3";
+			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
+			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#redistributor-regions = <1>;
+			redistributor-stride = <0x0 0x20000>;
+		};
+
+		memtimer: timer@17c20000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0 0x17c20000 0x0 0x1000>;
+			ranges = <0x0 0x0 0x0 0x20000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			frame@17c21000 {
+				reg = <0x17c21000 0x1000>,
+				      <0x17c22000 0x1000>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <0>;
+			};
+
+			frame@17c23000 {
+				reg = <0x17c23000 0x1000>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <1>;
+				status = "disabled";
+			};
+
+			frame@17c25000 {
+				reg = <0x17c25000 0x1000>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <2>;
+				status = "disabled";
+			};
+
+			frame@17c27000 {
+				reg = <0x17c27000 0x1000>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <3>;
+				status = "disabled";
+			};
+
+			frame@17c29000 {
+				reg = <0x17c29000 0x1000>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <4>;
+				status = "disabled";
+			};
+
+			frame@17c2b000 {
+				reg = <0x17c2b000 0x1000>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <5>;
+				status = "disabled";
+			};
+
+			frame@17c2d000 {
+				reg = <0x17c2d000 0x1000>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				frame-number = <6>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@18200000 {
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x0 0x18200000 0x0 0x10000>,
+			      <0x0 0x18210000 0x0 0x10000>,
+			      <0x0 0x18220000 0x0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			      <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			      <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS 2>,
+					  <SLEEP_TCS 3>,
+					  <WAKE_TCS 3>,
+					  <CONTROL_TCS 0>;
+			label = "apps_rsc";
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sa8775p-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board_clk>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sa8775p-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp-0 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp-1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp-4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp-5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp-6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp-7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp-8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp-9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+		};
+
+		cpufreq_hw: cpufreq@18591000 {
+			compatible = "qcom,sa8775p-cpufreq-epss",
+				     "qcom,cpufreq-epss";
+			reg = <0x0 0x18591000 0x0 0x1000>,
+			      <0x0 0x18593000 0x0 0x1000>;
+			reg-names = "freq-domain0", "freq-domain1";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
+			clock-names = "xo", "alternate";
+
+			#freq-domain-cells = <1>;
+		};
 	};
 
 	arch_timer: timer {
-- 
2.37.2

[PATCH v3 03/18] dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add a compatible for the Power Domain Controller on SA8775p platforms.
Increase the number of PDC pin mappings.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
---
 .../devicetree/bindings/interrupt-controller/qcom,pdc.yaml     | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
index 94791e261c42..641ff32e4a6c 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
@@ -26,6 +26,7 @@ properties:
   compatible:
     items:
       - enum:
+          - qcom,sa8775p-pdc
           - qcom,sc7180-pdc
           - qcom,sc7280-pdc
           - qcom,sc8280xp-pdc
@@ -53,7 +54,7 @@ properties:
   qcom,pdc-ranges:
     $ref: /schemas/types.yaml#/definitions/uint32-matrix
     minItems: 1
-    maxItems: 32 # no hard limit
+    maxItems: 38 # no hard limit
     items:
       items:
         - description: starting PDC port
-- 
2.37.2

Re: [PATCH v3 03/18] dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p

[Krzysztof Kozlowski]

On 27/03/2023 14:53, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add a compatible for the Power Domain Controller on SA8775p platforms.
> Increase the number of PDC pin mappings.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH v3 03/18] dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p

[Bartosz Golaszewski]

On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>
> Add a compatible for the Power Domain Controller on SA8775p platforms.
> Increase the number of PDC pin mappings.
>
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> Cc: Thomas Gleixner <tglx@linutronix.de>
> Cc: Marc Zyngier <maz@kernel.org>
> ---
>  .../devicetree/bindings/interrupt-controller/qcom,pdc.yaml     | 3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> index 94791e261c42..641ff32e4a6c 100644
> --- a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> +++ b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> @@ -26,6 +26,7 @@ properties:
>    compatible:
>      items:
>        - enum:
> +          - qcom,sa8775p-pdc
>            - qcom,sc7180-pdc
>            - qcom,sc7280-pdc
>            - qcom,sc8280xp-pdc
> @@ -53,7 +54,7 @@ properties:
>    qcom,pdc-ranges:
>      $ref: /schemas/types.yaml#/definitions/uint32-matrix
>      minItems: 1
> -    maxItems: 32 # no hard limit
> +    maxItems: 38 # no hard limit
>      items:
>        items:
>          - description: starting PDC port
> --
> 2.37.2
>

Bjorn,

Will you pick up the dt-bindings patches from this series as well or
should they go through Rob's tree?

Bart

Re: [PATCH v3 03/18] dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p

[Bartosz Golaszewski]

On Thu, Apr 6, 2023 at 4:10 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>
> On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
> >
> > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> >
> > Add a compatible for the Power Domain Controller on SA8775p platforms.
> > Increase the number of PDC pin mappings.
> >
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > Cc: Thomas Gleixner <tglx@linutronix.de>
> > Cc: Marc Zyngier <maz@kernel.org>
> > ---
> >  .../devicetree/bindings/interrupt-controller/qcom,pdc.yaml     | 3 ++-
> >  1 file changed, 2 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> > index 94791e261c42..641ff32e4a6c 100644
> > --- a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> > +++ b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> > @@ -26,6 +26,7 @@ properties:
> >    compatible:
> >      items:
> >        - enum:
> > +          - qcom,sa8775p-pdc
> >            - qcom,sc7180-pdc
> >            - qcom,sc7280-pdc
> >            - qcom,sc8280xp-pdc
> > @@ -53,7 +54,7 @@ properties:
> >    qcom,pdc-ranges:
> >      $ref: /schemas/types.yaml#/definitions/uint32-matrix
> >      minItems: 1
> > -    maxItems: 32 # no hard limit
> > +    maxItems: 38 # no hard limit
> >      items:
> >        items:
> >          - description: starting PDC port
> > --
> > 2.37.2
> >
>
> Bjorn,
>
> Will you pick up the dt-bindings patches from this series as well or
> should they go through Rob's tree?
>
> Bart

Gentle ping as this one's still not in next.

Bart

Re: [PATCH v3 03/18] dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p

[Krzysztof Kozlowski]

On 14/04/2023 11:33, Bartosz Golaszewski wrote:
> On Thu, Apr 6, 2023 at 4:10 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>>
>> On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>>>
>>> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>>>
>>> Add a compatible for the Power Domain Controller on SA8775p platforms.
>>> Increase the number of PDC pin mappings.
>>>
>>> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>>> Cc: Thomas Gleixner <tglx@linutronix.de>
>>> Cc: Marc Zyngier <maz@kernel.org>
>>> ---
>>>  .../devicetree/bindings/interrupt-controller/qcom,pdc.yaml     | 3 ++-
>>>  1 file changed, 2 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>> index 94791e261c42..641ff32e4a6c 100644
>>> --- a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>> +++ b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>> @@ -26,6 +26,7 @@ properties:
>>>    compatible:
>>>      items:
>>>        - enum:
>>> +          - qcom,sa8775p-pdc
>>>            - qcom,sc7180-pdc
>>>            - qcom,sc7280-pdc
>>>            - qcom,sc8280xp-pdc
>>> @@ -53,7 +54,7 @@ properties:
>>>    qcom,pdc-ranges:
>>>      $ref: /schemas/types.yaml#/definitions/uint32-matrix
>>>      minItems: 1
>>> -    maxItems: 32 # no hard limit
>>> +    maxItems: 38 # no hard limit

I don't think the limit is correct. I still see warnings with this
patch. We already have 57 elements, so limit should be I guess 128 or
something.

Best regards,
Krzysztof

Re: [PATCH v3 03/18] dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p

[Bartosz Golaszewski]

On Sun, Apr 16, 2023 at 5:04 PM Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
>
> On 14/04/2023 11:33, Bartosz Golaszewski wrote:
> > On Thu, Apr 6, 2023 at 4:10 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
> >>
> >> On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
> >>>
> >>> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> >>>
> >>> Add a compatible for the Power Domain Controller on SA8775p platforms.
> >>> Increase the number of PDC pin mappings.
> >>>
> >>> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> >>> Cc: Thomas Gleixner <tglx@linutronix.de>
> >>> Cc: Marc Zyngier <maz@kernel.org>
> >>> ---
> >>>  .../devicetree/bindings/interrupt-controller/qcom,pdc.yaml     | 3 ++-
> >>>  1 file changed, 2 insertions(+), 1 deletion(-)
> >>>
> >>> diff --git a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> >>> index 94791e261c42..641ff32e4a6c 100644
> >>> --- a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> >>> +++ b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
> >>> @@ -26,6 +26,7 @@ properties:
> >>>    compatible:
> >>>      items:
> >>>        - enum:
> >>> +          - qcom,sa8775p-pdc
> >>>            - qcom,sc7180-pdc
> >>>            - qcom,sc7280-pdc
> >>>            - qcom,sc8280xp-pdc
> >>> @@ -53,7 +54,7 @@ properties:
> >>>    qcom,pdc-ranges:
> >>>      $ref: /schemas/types.yaml#/definitions/uint32-matrix
> >>>      minItems: 1
> >>> -    maxItems: 32 # no hard limit
> >>> +    maxItems: 38 # no hard limit
>
> I don't think the limit is correct. I still see warnings with this
> patch. We already have 57 elements, so limit should be I guess 128 or
> something.
>

You mean for other platforms? This limit applies to sa8775p as the
goal of the patch is to add its own PDC compatible. If other platforms
have more interrupts then we need to fix it first with a separate
commit IMO. I'll send out two patches for that.

Brt

Re: [PATCH v3 03/18] dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p

[Krzysztof Kozlowski]

On 17/04/2023 09:27, Bartosz Golaszewski wrote:
> On Sun, Apr 16, 2023 at 5:04 PM Krzysztof Kozlowski
> <krzysztof.kozlowski@linaro.org> wrote:
>>
>> On 14/04/2023 11:33, Bartosz Golaszewski wrote:
>>> On Thu, Apr 6, 2023 at 4:10 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>>>>
>>>> On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>>>>>
>>>>> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>>>>>
>>>>> Add a compatible for the Power Domain Controller on SA8775p platforms.
>>>>> Increase the number of PDC pin mappings.
>>>>>
>>>>> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>>>>> Cc: Thomas Gleixner <tglx@linutronix.de>
>>>>> Cc: Marc Zyngier <maz@kernel.org>
>>>>> ---
>>>>>  .../devicetree/bindings/interrupt-controller/qcom,pdc.yaml     | 3 ++-
>>>>>  1 file changed, 2 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>>>> index 94791e261c42..641ff32e4a6c 100644
>>>>> --- a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>>>> +++ b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>>>> @@ -26,6 +26,7 @@ properties:
>>>>>    compatible:
>>>>>      items:
>>>>>        - enum:
>>>>> +          - qcom,sa8775p-pdc
>>>>>            - qcom,sc7180-pdc
>>>>>            - qcom,sc7280-pdc
>>>>>            - qcom,sc8280xp-pdc
>>>>> @@ -53,7 +54,7 @@ properties:
>>>>>    qcom,pdc-ranges:
>>>>>      $ref: /schemas/types.yaml#/definitions/uint32-matrix
>>>>>      minItems: 1
>>>>> -    maxItems: 32 # no hard limit
>>>>> +    maxItems: 38 # no hard limit
>>
>> I don't think the limit is correct. I still see warnings with this
>> patch. We already have 57 elements, so limit should be I guess 128 or
>> something.
>>
> 
> You mean for other platforms? This limit applies to sa8775p as the

I see errors on sa8775p.

> goal of the patch is to add its own PDC compatible. If other platforms
> have more interrupts then we need to fix it first with a separate
> commit IMO. I'll send out two patches for that.

Best regards,
Krzysztof

Re: [PATCH v3 03/18] dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p

[Krzysztof Kozlowski]

On 17/04/2023 09:55, Krzysztof Kozlowski wrote:
> On 17/04/2023 09:27, Bartosz Golaszewski wrote:
>> On Sun, Apr 16, 2023 at 5:04 PM Krzysztof Kozlowski
>> <krzysztof.kozlowski@linaro.org> wrote:
>>>
>>> On 14/04/2023 11:33, Bartosz Golaszewski wrote:
>>>> On Thu, Apr 6, 2023 at 4:10 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>>>>>
>>>>> On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>>>>>>
>>>>>> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>>>>>>
>>>>>> Add a compatible for the Power Domain Controller on SA8775p platforms.
>>>>>> Increase the number of PDC pin mappings.
>>>>>>
>>>>>> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>>>>>> Cc: Thomas Gleixner <tglx@linutronix.de>
>>>>>> Cc: Marc Zyngier <maz@kernel.org>
>>>>>> ---
>>>>>>  .../devicetree/bindings/interrupt-controller/qcom,pdc.yaml     | 3 ++-
>>>>>>  1 file changed, 2 insertions(+), 1 deletion(-)
>>>>>>
>>>>>> diff --git a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>>>>> index 94791e261c42..641ff32e4a6c 100644
>>>>>> --- a/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>>>>> +++ b/Documentation/devicetree/bindings/interrupt-controller/qcom,pdc.yaml
>>>>>> @@ -26,6 +26,7 @@ properties:
>>>>>>    compatible:
>>>>>>      items:
>>>>>>        - enum:
>>>>>> +          - qcom,sa8775p-pdc
>>>>>>            - qcom,sc7180-pdc
>>>>>>            - qcom,sc7280-pdc
>>>>>>            - qcom,sc8280xp-pdc
>>>>>> @@ -53,7 +54,7 @@ properties:
>>>>>>    qcom,pdc-ranges:
>>>>>>      $ref: /schemas/types.yaml#/definitions/uint32-matrix
>>>>>>      minItems: 1
>>>>>> -    maxItems: 32 # no hard limit
>>>>>> +    maxItems: 38 # no hard limit
>>>
>>> I don't think the limit is correct. I still see warnings with this
>>> patch. We already have 57 elements, so limit should be I guess 128 or
>>> something.
>>>
>>
>> You mean for other platforms? This limit applies to sa8775p as the
> 
> I see errors on sa8775p.

OK, so as you pointed out it's about other platform - sa8540p-ride.
Anyway you update now this line to bump the limit, so bump it to
something high instead of changing it in two patches.

Best regards,
Krzysztof

[PATCH v3 04/18] arm64: dts: qcom: sa8775p: add the pdc node

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the Power Domain Controller node for SA8775p.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p.dtsi | 47 +++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index 296ba69b81ab..6bb1db1839cc 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -591,6 +591,53 @@ tcsr_mutex: hwlock@1f40000 {
 			#hwlock-cells = <1>;
 		};
 
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sa8775p-pdc", "qcom,pdc";
+			reg = <0x0 0x0b220000 0x0 0x30000>,
+			      <0x0 0x17c000f0 0x0 0x64>;
+			qcom,pdc-ranges = <0 480 40>,
+					  <40 140 14>,
+					  <54 263 1>,
+					  <55 306 4>,
+					  <59 312 3>,
+					  <62 374 2>,
+					  <64 434 2>,
+					  <66 438 2>,
+					  <70 520 1>,
+					  <73 523 1>,
+					  <118 568 6>,
+					  <124 609 3>,
+					  <159 638 1>,
+					  <160 720 3>,
+					  <169 728 30>,
+					  <199 416 2>,
+					  <201 449 1>,
+					  <202 89 1>,
+					  <203 451 1>,
+					  <204 462 1>,
+					  <205 264 1>,
+					  <206 579 1>,
+					  <207 653 1>,
+					  <208 656 1>,
+					  <209 659 1>,
+					  <210 122 1>,
+					  <211 699 1>,
+					  <212 705 1>,
+					  <213 450 1>,
+					  <214 643 2>,
+					  <216 646 5>,
+					  <221 390 5>,
+					  <226 700 2>,
+					  <228 440 1>,
+					  <229 663 1>,
+					  <230 524 2>,
+					  <232 612 3>,
+					  <235 723 5>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
 		tlmm: pinctrl@f000000 {
 			compatible = "qcom,sa8775p-tlmm";
 			reg = <0x0 0x0f000000 0x0 0x1000000>;
-- 
2.37.2

Re: [PATCH v3 04/18] arm64: dts: qcom: sa8775p: add the pdc node

[Konrad Dybcio]

On 27.03.2023 14:53, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add the Power Domain Controller node for SA8775p.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  arch/arm64/boot/dts/qcom/sa8775p.dtsi | 47 +++++++++++++++++++++++++++
>  1 file changed, 47 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> index 296ba69b81ab..6bb1db1839cc 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> @@ -591,6 +591,53 @@ tcsr_mutex: hwlock@1f40000 {
>  			#hwlock-cells = <1>;
>  		};
>  
> +		pdc: interrupt-controller@b220000 {
> +			compatible = "qcom,sa8775p-pdc", "qcom,pdc";
> +			reg = <0x0 0x0b220000 0x0 0x30000>,
> +			      <0x0 0x17c000f0 0x0 0x64>;
> +			qcom,pdc-ranges = <0 480 40>,
> +					  <40 140 14>,
> +					  <54 263 1>,
> +					  <55 306 4>,
> +					  <59 312 3>,
> +					  <62 374 2>,
> +					  <64 434 2>,
> +					  <66 438 2>,
> +					  <70 520 1>,
> +					  <73 523 1>,
> +					  <118 568 6>,
> +					  <124 609 3>,
> +					  <159 638 1>,
> +					  <160 720 3>,
> +					  <169 728 30>,
> +					  <199 416 2>,
> +					  <201 449 1>,
> +					  <202 89 1>,
> +					  <203 451 1>,
> +					  <204 462 1>,
> +					  <205 264 1>,
> +					  <206 579 1>,
> +					  <207 653 1>,
> +					  <208 656 1>,
> +					  <209 659 1>,
> +					  <210 122 1>,
> +					  <211 699 1>,
> +					  <212 705 1>,
> +					  <213 450 1>,
> +					  <214 643 2>,
> +					  <216 646 5>,
> +					  <221 390 5>,
> +					  <226 700 2>,
> +					  <228 440 1>,
> +					  <229 663 1>,
> +					  <230 524 2>,
> +					  <232 612 3>,
> +					  <235 723 5>;
> +			#interrupt-cells = <2>;
> +			interrupt-parent = <&intc>;
> +			interrupt-controller;
> +		};
> +
>  		tlmm: pinctrl@f000000 {
>  			compatible = "qcom,sa8775p-tlmm";
>  			reg = <0x0 0x0f000000 0x0 0x1000000>;

[PATCH v3 05/18] arm64: dts: qcom: sa8775p: add the spmi node

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the SPMI PMIC Arbiter node for SA8775p platforms.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index 6bb1db1839cc..2343df7e0ea4 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -638,6 +638,28 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0 0x0c440000 0x0 0x1100>,
+			      <0x0 0x0c600000 0x0 0x2000000>,
+			      <0x0 0x0e600000 0x0 0x100000>,
+			      <0x0 0x0e700000 0x0 0xa0000>,
+			      <0x0 0x0c40a000 0x0 0x26000>;
+			reg-names = "core",
+				    "chnls",
+				    "obsrvr",
+				    "intr",
+				    "cnfg";
+			qcom,channel = <0>;
+			qcom,ee = <0>;
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "periph_irq";
+			interrupt-controller;
+			#interrupt-cells = <4>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
 		tlmm: pinctrl@f000000 {
 			compatible = "qcom,sa8775p-tlmm";
 			reg = <0x0 0x0f000000 0x0 0x1000000>;
-- 
2.37.2

[PATCH v3 06/18] dt-bindings: mfd: qcom,spmi-pmic: add compatible for pmm8654au

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

PMM8654au is the SPMI PMIC variant used on sa8775p-ride. Add a compatible
for it.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: Lee Jones <lee@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
index 975c30aad23c..0f7dd7ac9630 100644
--- a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
+++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
@@ -79,6 +79,7 @@ properties:
           - qcom,pmk8350
           - qcom,pmk8550
           - qcom,pmm8155au
+          - qcom,pmm8654au
           - qcom,pmp8074
           - qcom,pmr735a
           - qcom,pmr735b
-- 
2.37.2

Re: [PATCH v3 06/18] dt-bindings: mfd: qcom,spmi-pmic: add compatible for pmm8654au

[Lee Jones]

On Mon, 27 Mar 2023, Bartosz Golaszewski wrote:

> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>
> PMM8654au is the SPMI PMIC variant used on sa8775p-ride. Add a compatible
> for it.
>
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> Cc: Lee Jones <lee@kernel.org>
> Acked-by: Rob Herring <robh@kernel.org>
> ---

Change-log?

>  Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> index 975c30aad23c..0f7dd7ac9630 100644
> --- a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> +++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> @@ -79,6 +79,7 @@ properties:
>            - qcom,pmk8350
>            - qcom,pmk8550
>            - qcom,pmm8155au
> +          - qcom,pmm8654au
>            - qcom,pmp8074
>            - qcom,pmr735a
>            - qcom,pmr735b

I believe this is already applied, right?

Not sure why I have 3 copies of seemingly the same patch in my inbox.

--
Lee Jones [李琼斯]

Re: [PATCH v3 06/18] dt-bindings: mfd: qcom,spmi-pmic: add compatible for pmm8654au

[Bartosz Golaszewski]

On Thu, Mar 30, 2023 at 3:13 PM Lee Jones <lee@kernel.org> wrote:
>
> On Mon, 27 Mar 2023, Bartosz Golaszewski wrote:
>
> > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> >
> > PMM8654au is the SPMI PMIC variant used on sa8775p-ride. Add a compatible
> > for it.
> >
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > Cc: Lee Jones <lee@kernel.org>
> > Acked-by: Rob Herring <robh@kernel.org>
> > ---
>
> Change-log?
>
> >  Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml | 1 +
> >  1 file changed, 1 insertion(+)
> >
> > diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> > index 975c30aad23c..0f7dd7ac9630 100644
> > --- a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> > +++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> > @@ -79,6 +79,7 @@ properties:
> >            - qcom,pmk8350
> >            - qcom,pmk8550
> >            - qcom,pmm8155au
> > +          - qcom,pmm8654au
> >            - qcom,pmp8074
> >            - qcom,pmr735a
> >            - qcom,pmr735b
>
> I believe this is already applied, right?
>
> Not sure why I have 3 copies of seemingly the same patch in my inbox.
>

I've sent out three iterations of the series containing it. This one
didn't change. As the rest of 18 patches don't concern your subsystem,
I decided to only Cc you on this one. Let me know if you prefer to
receive the entire series even if only a single patch needs your
attention. The reaction to such dumps varies from maintainer to
maintainer so I chose the safe approach. :)

Bart

> --
> Lee Jones [李琼斯]

Re: [PATCH v3 06/18] dt-bindings: mfd: qcom,spmi-pmic: add compatible for pmm8654au

[Lee Jones]

On Thu, 30 Mar 2023, Bartosz Golaszewski wrote:

> On Thu, Mar 30, 2023 at 3:13 PM Lee Jones <lee@kernel.org> wrote:
> >
> > On Mon, 27 Mar 2023, Bartosz Golaszewski wrote:
> >
> > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > >
> > > PMM8654au is the SPMI PMIC variant used on sa8775p-ride. Add a compatible
> > > for it.
> > >
> > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > > Cc: Lee Jones <lee@kernel.org>
> > > Acked-by: Rob Herring <robh@kernel.org>
> > > ---
> >
> > Change-log?
> >
> > >  Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml | 1 +
> > >  1 file changed, 1 insertion(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> > > index 975c30aad23c..0f7dd7ac9630 100644
> > > --- a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> > > +++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
> > > @@ -79,6 +79,7 @@ properties:
> > >            - qcom,pmk8350
> > >            - qcom,pmk8550
> > >            - qcom,pmm8155au
> > > +          - qcom,pmm8654au
> > >            - qcom,pmp8074
> > >            - qcom,pmr735a
> > >            - qcom,pmr735b
> >
> > I believe this is already applied, right?
> >
> > Not sure why I have 3 copies of seemingly the same patch in my inbox.
> >
>
> I've sent out three iterations of the series containing it. This one
> didn't change. As the rest of 18 patches don't concern your subsystem,
> I decided to only Cc you on this one. Let me know if you prefer to
> receive the entire series even if only a single patch needs your
> attention. The reaction to such dumps varies from maintainer to
> maintainer so I chose the safe approach. :)

There is no simple answer to that question.

Not Cc:ing me on this whole set appears to be the correct decision.

--
Lee Jones [李琼斯]

[PATCH v3 07/18] arm64: dts: qcom: sa8775p: add support for the on-board PMICs

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add a new .dtsi file for sa8775p PMICs and add the four PMICs interfaced
to the SoC via SPMI. Enable the PMICs for sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 37 +++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sa8775p-ride.dts   |  1 +
 2 files changed, 38 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
new file mode 100644
index 000000000000..afe220b374c2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmm8654au_0: pmic@0 {
+		compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmm8654au_1: pmic@2 {
+		compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmm8654au_2: pmic@4 {
+		compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmm8654au_3: pmic@6 {
+		compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
+		reg = <0x6 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
index 1020dfd21da2..b7ee4cc676b5 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "sa8775p.dtsi"
+#include "sa8775p-pmics.dtsi"
 
 / {
 	model = "Qualcomm SA8775P Ride";
-- 
2.37.2

[PATCH v3 08/18] arm64: dts: qcom: sa8775p: add the Power On device node

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the PON node to PMIC #0 for sa8775p platforms.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
index afe220b374c2..dbc596e32253 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
@@ -12,6 +12,14 @@ pmm8654au_0: pmic@0 {
 		reg = <0x0 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pmm8654au_0_pon: pon@1200 {
+			compatible = "qcom,pmk8350-pon";
+			reg = <0x1200>, <0x800>;
+			reg-names = "hlos", "pbs";
+			mode-recovery = <0x1>;
+			mode-bootloader = <0x2>;
+		};
 	};
 
 	pmm8654au_1: pmic@2 {
-- 
2.37.2

[PATCH v3 09/18] arm64: dts: qcom: sa8775p: pmic: add the power key

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the power key node under the PON node for PMIC #0 on sa8775p.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
index dbc596e32253..f421d4d64c8e 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
@@ -19,6 +19,13 @@ pmm8654au_0_pon: pon@1200 {
 			reg-names = "hlos", "pbs";
 			mode-recovery = <0x1>;
 			mode-bootloader = <0x2>;
+
+			pmm8654au_0_pon_pwrkey: pwrkey {
+				compatible = "qcom,pmk8350-pwrkey";
+				interrupts-extended = <&spmi_bus 0x0 0x12 0x7 IRQ_TYPE_EDGE_BOTH>;
+				linux,code = <KEY_POWER>;
+				debounce = <15625>;
+			};
 		};
 	};
 
-- 
2.37.2

[PATCH v3 10/18] arm64: dts: qcom: sa8775p: pmic: add support for the pmm8654 RESIN input

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the RESIN input for sa8775p platforms' PMIC.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
index f421d4d64c8e..8616ead3daf5 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
@@ -26,6 +26,13 @@ pmm8654au_0_pon_pwrkey: pwrkey {
 				linux,code = <KEY_POWER>;
 				debounce = <15625>;
 			};
+
+			pmm8654au_0_pon_resin: resin {
+				compatible = "qcom,pmk8350-resin";
+				interrupts-extended = <&spmi_bus 0x0 0x12 0x6 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				status = "disabled";
+			};
 		};
 	};
 
-- 
2.37.2

[PATCH v3 11/18] arm64: dts: qcom: sa8775p: pmic: add thermal zones

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the thermal zones and associated alarm nodes for the PMICs that have
them hooked up on sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 112 ++++++++++++++++++++
 1 file changed, 112 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
index 8616ead3daf5..be12997a080c 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
@@ -6,6 +6,90 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/spmi/spmi.h>
 
+/ {
+	thermal-zones {
+		pmm8654au_0_thermal: pm8775-0-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmm8654au_0_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		pmm8654au_1_thermal: pm8775-1-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmm8654au_1_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		pmm8654au_2_thermal: pm8775-2-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmm8654au_2_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		pmm8654au_3_thermal: pm8775-3-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmm8654au_3_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 	pmm8654au_0: pmic@0 {
 		compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
@@ -13,6 +97,13 @@ pmm8654au_0: pmic@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pmm8654au_0_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts-extended = <&spmi_bus 0x0 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
 		pmm8654au_0_pon: pon@1200 {
 			compatible = "qcom,pmk8350-pon";
 			reg = <0x1200>, <0x800>;
@@ -41,6 +132,13 @@ pmm8654au_1: pmic@2 {
 		reg = <0x2 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pmm8654au_1_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
 	};
 
 	pmm8654au_2: pmic@4 {
@@ -48,6 +146,13 @@ pmm8654au_2: pmic@4 {
 		reg = <0x4 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pmm8654au_2_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
 	};
 
 	pmm8654au_3: pmic@6 {
@@ -55,5 +160,12 @@ pmm8654au_3: pmic@6 {
 		reg = <0x6 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pmm8654au_3_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
 	};
 };
-- 
2.37.2

Re: [PATCH v3 11/18] arm64: dts: qcom: sa8775p: pmic: add thermal zones

[Konrad Dybcio]

On 27.03.2023 14:53, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add the thermal zones and associated alarm nodes for the PMICs that have
> them hooked up on sa8775p-ride.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 112 ++++++++++++++++++++
>  1 file changed, 112 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> index 8616ead3daf5..be12997a080c 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> @@ -6,6 +6,90 @@
>  #include <dt-bindings/input/input.h>
>  #include <dt-bindings/spmi/spmi.h>
>  
> +/ {
> +	thermal-zones {
> +		pmm8654au_0_thermal: pm8775-0-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmm8654au_0_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <105000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <125000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		pmm8654au_1_thermal: pm8775-1-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmm8654au_1_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <105000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <125000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		pmm8654au_2_thermal: pm8775-2-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmm8654au_2_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <105000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <125000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		pmm8654au_3_thermal: pm8775-3-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +			thermal-sensors = <&pmm8654au_3_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <105000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <125000>;
> +					hysteresis = <0>;
> +					type = "critical";
> +				};
> +			};
> +		};
> +	};
> +};
> +
>  &spmi_bus {
>  	pmm8654au_0: pmic@0 {
>  		compatible = "qcom,pmm8654au", "qcom,spmi-pmic";
> @@ -13,6 +97,13 @@ pmm8654au_0: pmic@0 {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
>  
> +		pmm8654au_0_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts-extended = <&spmi_bus 0x0 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +
>  		pmm8654au_0_pon: pon@1200 {
>  			compatible = "qcom,pmk8350-pon";
>  			reg = <0x1200>, <0x800>;
> @@ -41,6 +132,13 @@ pmm8654au_1: pmic@2 {
>  		reg = <0x2 SPMI_USID>;
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> +
> +		pmm8654au_1_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
>  	};
>  
>  	pmm8654au_2: pmic@4 {
> @@ -48,6 +146,13 @@ pmm8654au_2: pmic@4 {
>  		reg = <0x4 SPMI_USID>;
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> +
> +		pmm8654au_2_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
>  	};
>  
>  	pmm8654au_3: pmic@6 {
> @@ -55,5 +160,12 @@ pmm8654au_3: pmic@6 {
>  		reg = <0x6 SPMI_USID>;
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> +
> +		pmm8654au_3_temp_alarm: temp-alarm@a00 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0xa00>;
> +			interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
>  	};
>  };

[PATCH v3 12/18] dt-bindings: pinctrl: qcom,pmic-gpio: add compatible for pmm8654au-gpio

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add a new compatible for the GPIO controller on the pm8654au PMIC. It
has 12 pins with no holes.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml
index db505fdeac86..512378a2d4fd 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml
@@ -58,6 +58,7 @@ properties:
           - qcom,pmk8350-gpio
           - qcom,pmk8550-gpio
           - qcom,pmm8155au-gpio
+          - qcom,pmm8654au-gpio
           - qcom,pmp8074-gpio
           - qcom,pmr735a-gpio
           - qcom,pmr735b-gpio
@@ -439,6 +440,7 @@ $defs:
                  - gpio1-gpio4 for pmk8350
                  - gpio1-gpio6 for pmk8550
                  - gpio1-gpio10 for pmm8155au
+                 - gpio1-gpio12 for pmm8654au
                  - gpio1-gpio12 for pmp8074 (holes on gpio1 and gpio12)
                  - gpio1-gpio4 for pmr735a
                  - gpio1-gpio4 for pmr735b
-- 
2.37.2

Re: [PATCH v3 12/18] dt-bindings: pinctrl: qcom,pmic-gpio: add compatible for pmm8654au-gpio

[Linus Walleij]

On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:

> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>
> Add a new compatible for the GPIO controller on the pm8654au PMIC. It
> has 12 pins with no holes.
>
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> Cc: Linus Walleij <linus.walleij@linaro.org>
> Acked-by: Rob Herring <robh@kernel.org>

Acked-by: Linus Walleij <linus.walleij@linaro.org>

Counting on Bjorn to pick this up.

Yours,
Linus Walleij

Re: [PATCH v3 12/18] dt-bindings: pinctrl: qcom,pmic-gpio: add compatible for pmm8654au-gpio

[Bartosz Golaszewski]

On Tue, Mar 28, 2023 at 3:24 PM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>
> > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> >
> > Add a new compatible for the GPIO controller on the pm8654au PMIC. It
> > has 12 pins with no holes.
> >
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > Cc: Linus Walleij <linus.walleij@linaro.org>
> > Acked-by: Rob Herring <robh@kernel.org>
>
> Acked-by: Linus Walleij <linus.walleij@linaro.org>
>
> Counting on Bjorn to pick this up.
>
> Yours,
> Linus Walleij

Linus,

Bjorn picked up the arm64 patches but these two were skipped. Can you
take it through the pinctrl tree?

Bart

Re: [PATCH v3 12/18] dt-bindings: pinctrl: qcom,pmic-gpio: add compatible for pmm8654au-gpio

[Linus Walleij]

On Thu, Apr 6, 2023 at 4:09 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
> On Tue, Mar 28, 2023 at 3:24 PM Linus Walleij <linus.walleij@linaro.org> wrote:
> > On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
> >
> > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > >
> > > Add a new compatible for the GPIO controller on the pm8654au PMIC. It
> > > has 12 pins with no holes.
> > >
> > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > > Cc: Linus Walleij <linus.walleij@linaro.org>
> > > Acked-by: Rob Herring <robh@kernel.org>
> >
> > Acked-by: Linus Walleij <linus.walleij@linaro.org>
> >
> > Counting on Bjorn to pick this up.
> >
> > Yours,
> > Linus Walleij
>
> Linus,
>
> Bjorn picked up the arm64 patches but these two were skipped. Can you
> take it through the pinctrl tree?

OK patches 12 and 13 applied to the pinctrl tree!

Yours,
Linus Walleij

[PATCH v3 13/18] pinctrl: qcom: spmi-gpio: add support for pmm8654au-gpio

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add support for the GPIO controller present on the pmm8654au PMIC.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
index ea3485344f06..0d94175b34f8 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -1238,6 +1238,7 @@ static const struct of_device_id pmic_gpio_of_match[] = {
 	{ .compatible = "qcom,pmk8350-gpio", .data = (void *) 4 },
 	{ .compatible = "qcom,pmk8550-gpio", .data = (void *) 6 },
 	{ .compatible = "qcom,pmm8155au-gpio", .data = (void *) 10 },
+	{ .compatible = "qcom,pmm8654au-gpio", .data = (void *) 12 },
 	/* pmp8074 has 12 GPIOs with holes on 1 and 12 */
 	{ .compatible = "qcom,pmp8074-gpio", .data = (void *) 12 },
 	{ .compatible = "qcom,pmr735a-gpio", .data = (void *) 4 },
-- 
2.37.2

Re: [PATCH v3 13/18] pinctrl: qcom: spmi-gpio: add support for pmm8654au-gpio

[Linus Walleij]

On Mon, Mar 27, 2023 at 2:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:

> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>
> Add support for the GPIO controller present on the pmm8654au PMIC.
>
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> Cc: Linus Walleij <linus.walleij@linaro.org>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Acked-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij

[PATCH v3 14/18] arm64: dts: qcom: sa8775p: add PMIC GPIO controller nodes

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add GPIO controller nodes to PMICs that have the GPIO hooked up on
sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 40 +++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
index be12997a080c..7602cca47bae 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
@@ -125,6 +125,16 @@ pmm8654au_0_pon_resin: resin {
 				status = "disabled";
 			};
 		};
+
+		pmm8654au_0_gpios: gpio@8800 {
+			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmm8654au_0_gpios 0 0 12>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 
 	pmm8654au_1: pmic@2 {
@@ -139,6 +149,16 @@ pmm8654au_1_temp_alarm: temp-alarm@a00 {
 			interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
 			#thermal-sensor-cells = <0>;
 		};
+
+		pmm8654au_1_gpios: gpio@8800 {
+			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 
 	pmm8654au_2: pmic@4 {
@@ -153,6 +173,16 @@ pmm8654au_2_temp_alarm: temp-alarm@a00 {
 			interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
 			#thermal-sensor-cells = <0>;
 		};
+
+		pmm8654au_2_gpios: gpio@8800 {
+			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 
 	pmm8654au_3: pmic@6 {
@@ -167,5 +197,15 @@ pmm8654au_3_temp_alarm: temp-alarm@a00 {
 			interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
 			#thermal-sensor-cells = <0>;
 		};
+
+		pmm8654au_3_gpios: gpio@8800 {
+			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmm8654au_3_gpios 0 0 12>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 };
-- 
2.37.2

Re: [PATCH v3 14/18] arm64: dts: qcom: sa8775p: add PMIC GPIO controller nodes

[Konrad Dybcio]

On 27.03.2023 14:53, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add GPIO controller nodes to PMICs that have the GPIO hooked up on
> sa8775p-ride.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi | 40 +++++++++++++++++++++
>  1 file changed, 40 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> index be12997a080c..7602cca47bae 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sa8775p-pmics.dtsi
> @@ -125,6 +125,16 @@ pmm8654au_0_pon_resin: resin {
>  				status = "disabled";
>  			};
>  		};
> +
> +		pmm8654au_0_gpios: gpio@8800 {
> +			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmm8654au_0_gpios 0 0 12>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
>  	};
>  
>  	pmm8654au_1: pmic@2 {
> @@ -139,6 +149,16 @@ pmm8654au_1_temp_alarm: temp-alarm@a00 {
>  			interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
>  			#thermal-sensor-cells = <0>;
>  		};
> +
> +		pmm8654au_1_gpios: gpio@8800 {
> +			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
>  	};
>  
>  	pmm8654au_2: pmic@4 {
> @@ -153,6 +173,16 @@ pmm8654au_2_temp_alarm: temp-alarm@a00 {
>  			interrupts-extended = <&spmi_bus 0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
>  			#thermal-sensor-cells = <0>;
>  		};
> +
> +		pmm8654au_2_gpios: gpio@8800 {
> +			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmm8654au_2_gpios 0 0 12>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
>  	};
>  
>  	pmm8654au_3: pmic@6 {
> @@ -167,5 +197,15 @@ pmm8654au_3_temp_alarm: temp-alarm@a00 {
>  			interrupts-extended = <&spmi_bus 0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
>  			#thermal-sensor-cells = <0>;
>  		};
> +
> +		pmm8654au_3_gpios: gpio@8800 {
> +			compatible = "qcom,pmm8654au-gpio", "qcom,spmi-gpio";
> +			reg = <0x8800>;
> +			gpio-controller;
> +			gpio-ranges = <&pmm8654au_3_gpios 0 0 12>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
>  	};
>  };

[PATCH v3 15/18] arm64: dts: qcom: sa8775p-ride: set gpio-line-names for PMIC GPIOs

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Set line names for GPIO lines exposed by PMICs on sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 51 +++++++++++++++++++++++
 1 file changed, 51 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
index b7ee4cc676b5..a0d2024a69df 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
@@ -32,6 +32,57 @@ &i2c18 {
 	status = "okay";
 };
 
+&pmm8654au_0_gpios {
+	gpio-line-names = "DS_EN",
+			  "POFF_COMPLETE",
+			  "UFS0_VER_ID",
+			  "FAST_POFF",
+			  "DBU1_PON_DONE",
+			  "AOSS_SLEEP",
+			  "CAM_DES0_EN",
+			  "CAM_DES1_EN",
+			  "CAM_DES2_EN",
+			  "CAM_DES3_EN",
+			  "UEFI",
+			  "ANALOG_PON_OPT";
+};
+
+&pmm8654au_1_gpios {
+	gpio-line-names = "PMIC_C_ID0",
+			  "PMIC_C_ID1",
+			  "UFS1_VER_ID",
+			  "IPA_PWR",
+			  "",
+			  "WLAN_DBU4_EN",
+			  "WLAN_EN",
+			  "BT_EN",
+			  "USB2_PWR_EN",
+			  "USB2_FAULT";
+};
+
+&pmm8654au_2_gpios {
+	gpio-line-names = "PMIC_E_ID0",
+			  "PMIC_E_ID1",
+			  "USB0_PWR_EN",
+			  "USB0_FAULT",
+			  "SENSOR_IRQ_1",
+			  "SENSOR_IRQ_2",
+			  "SENSOR_RST",
+			  "SGMIIO0_RST",
+			  "SGMIIO1_RST",
+			  "USB1_PWR_ENABLE",
+			  "USB1_FAULT",
+			  "VMON_SPX8";
+};
+
+&pmm8654au_3_gpios {
+	gpio-line-names = "PMIC_G_ID0",
+			  "PMIC_G_ID1",
+			  "GNSS_RST",
+			  "GNSS_EN",
+			  "GNSS_BOOT_MODE";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
-- 
2.37.2

Re: [PATCH v3 15/18] arm64: dts: qcom: sa8775p-ride: set gpio-line-names for PMIC GPIOs

[Konrad Dybcio]

On 27.03.2023 14:53, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Set line names for GPIO lines exposed by PMICs on sa8775p-ride.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 51 +++++++++++++++++++++++
>  1 file changed, 51 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> index b7ee4cc676b5..a0d2024a69df 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> @@ -32,6 +32,57 @@ &i2c18 {
>  	status = "okay";
>  };
>  
> +&pmm8654au_0_gpios {
> +	gpio-line-names = "DS_EN",
> +			  "POFF_COMPLETE",
> +			  "UFS0_VER_ID",
> +			  "FAST_POFF",
> +			  "DBU1_PON_DONE",
> +			  "AOSS_SLEEP",
> +			  "CAM_DES0_EN",
> +			  "CAM_DES1_EN",
> +			  "CAM_DES2_EN",
> +			  "CAM_DES3_EN",
> +			  "UEFI",
> +			  "ANALOG_PON_OPT";
> +};
> +
> +&pmm8654au_1_gpios {
> +	gpio-line-names = "PMIC_C_ID0",
> +			  "PMIC_C_ID1",
> +			  "UFS1_VER_ID",
> +			  "IPA_PWR",
> +			  "",
> +			  "WLAN_DBU4_EN",
> +			  "WLAN_EN",
> +			  "BT_EN",
> +			  "USB2_PWR_EN",
> +			  "USB2_FAULT";
> +};
> +
> +&pmm8654au_2_gpios {
> +	gpio-line-names = "PMIC_E_ID0",
> +			  "PMIC_E_ID1",
> +			  "USB0_PWR_EN",
> +			  "USB0_FAULT",
> +			  "SENSOR_IRQ_1",
> +			  "SENSOR_IRQ_2",
> +			  "SENSOR_RST",
> +			  "SGMIIO0_RST",
> +			  "SGMIIO1_RST",
> +			  "USB1_PWR_ENABLE",
> +			  "USB1_FAULT",
> +			  "VMON_SPX8";
> +};
> +
> +&pmm8654au_3_gpios {
> +	gpio-line-names = "PMIC_G_ID0",
> +			  "PMIC_G_ID1",
> +			  "GNSS_RST",
> +			  "GNSS_EN",
> +			  "GNSS_BOOT_MODE";
> +};
> +
>  &qupv3_id_1 {
>  	status = "okay";
>  };

[PATCH v3 16/18] dt-bindings: regulator: qcom,rpmh: add compatible for pmm8654au RPMH

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the compatible for the pmm8654au RPMH regulators present on the
sa8775p-ride development board.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
---
 .../bindings/regulator/qcom,rpmh-regulator.yaml    | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
index a765837dc069..91054ed04c66 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
@@ -78,6 +78,7 @@ properties:
       - qcom,pmg1110-rpmh-regulators
       - qcom,pmi8998-rpmh-regulators
       - qcom,pmm8155au-rpmh-regulators
+      - qcom,pmm8654au-rpmh-regulators
       - qcom,pmr735a-rpmh-regulators
       - qcom,pmx55-rpmh-regulators
       - qcom,pmx65-rpmh-regulators
@@ -244,6 +245,19 @@ allOf:
       patternProperties:
         "^vdd-s([1-9]|10)-supply$": true
 
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pmm8654au-rpmh-regulators
+    then:
+      properties:
+        vdd-l2-l3-supply: true
+        vdd-l6-l7-supply: true
+        vdd-l8-l9-supply: true
+      patternProperties:
+        "^vdd-s[1-9]-supply$": true
+
   - if:
       properties:
         compatible:
-- 
2.37.2

Re: [PATCH v3 16/18] dt-bindings: regulator: qcom,rpmh: add compatible for pmm8654au RPMH

[Krzysztof Kozlowski]

On 27/03/2023 14:53, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add the compatible for the pmm8654au RPMH regulators present on the
> sa8775p-ride development board.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> Cc: Mark Brown <broonie@kernel.org>
> ---
>  .../bindings/regulator/qcom,rpmh-regulator.yaml    | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
> index a765837dc069..91054ed04c66 100644
> --- a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
> +++ b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml
> @@ -78,6 +78,7 @@ properties:
>        - qcom,pmg1110-rpmh-regulators
>        - qcom,pmi8998-rpmh-regulators
>        - qcom,pmm8155au-rpmh-regulators
> +      - qcom,pmm8654au-rpmh-regulators
>        - qcom,pmr735a-rpmh-regulators
>        - qcom,pmx55-rpmh-regulators
>        - qcom,pmx65-rpmh-regulators
> @@ -244,6 +245,19 @@ allOf:
>        patternProperties:
>          "^vdd-s([1-9]|10)-supply$": true
>  
> +  - if:
> +      properties:
> +        compatible:
> +          enum:
> +            - qcom,pmm8654au-rpmh-regulators
> +    then:
> +      properties:
> +        vdd-l2-l3-supply: true
> +        vdd-l6-l7-supply: true
> +        vdd-l8-l9-supply: true

What about l1, l4 and l5 supplies?


Best regards,
Krzysztof

[PATCH v3 17/18] regulator: qcom-rpmh: add support for pmm8654au regulators

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add the RPMH regulators exposed by the PMM8654au PMIC and its variants.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/qcom-rpmh-regulator.c | 55 +++++++++++++++++++++++++
 1 file changed, 55 insertions(+)

diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
index 4826d60e5d95..b0a58c62b1e2 100644
--- a/drivers/regulator/qcom-rpmh-regulator.c
+++ b/drivers/regulator/qcom-rpmh-regulator.c
@@ -694,6 +694,16 @@ static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
 	.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
 };
 
+static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
+	.regulator_type = VRM,
+	.ops = &rpmh_regulator_vrm_drms_ops,
+	.voltage_range = REGULATOR_LINEAR_RANGE(1800000, 0, 187, 8000),
+	.n_voltages = 188,
+	.hpm_min_load_uA = 10000,
+	.pmic_mode_map = pmic_mode_map_pmic5_ldo,
+	.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
+};
+
 static const struct rpmh_vreg_hw_data pmic5_nldo = {
 	.regulator_type = VRM,
 	.ops = &rpmh_regulator_vrm_drms_ops,
@@ -704,6 +714,16 @@ static const struct rpmh_vreg_hw_data pmic5_nldo = {
 	.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
 };
 
+static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
+	.regulator_type = VRM,
+	.ops = &rpmh_regulator_vrm_drms_ops,
+	.voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 210, 8000),
+	.n_voltages = 211,
+	.hpm_min_load_uA = 30000,
+	.pmic_mode_map = pmic_mode_map_pmic5_ldo,
+	.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
+};
+
 static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
 	.regulator_type = VRM,
 	.ops = &rpmh_regulator_vrm_ops,
@@ -749,6 +769,15 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = {
 	.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
 };
 
+static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = {
+	.regulator_type = VRM,
+	.ops = &rpmh_regulator_vrm_ops,
+	.voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+	.n_voltages = 215,
+	.pmic_mode_map = pmic_mode_map_pmic5_smps,
+	.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
+};
+
 static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
 	.regulator_type = VRM,
 	.ops = &rpmh_regulator_vrm_ops,
@@ -937,6 +966,28 @@ static const struct rpmh_vreg_init_data pmm8155au_vreg_data[] = {
 	{}
 };
 
+static const struct rpmh_vreg_init_data pmm8654au_vreg_data[] = {
+	RPMH_VREG("smps1",  "smp%s1",  &pmic5_ftsmps527,  "vdd-s1"),
+	RPMH_VREG("smps2",  "smp%s2",  &pmic5_ftsmps527,  "vdd-s2"),
+	RPMH_VREG("smps3",  "smp%s3",  &pmic5_ftsmps527,  "vdd-s3"),
+	RPMH_VREG("smps4",  "smp%s4",  &pmic5_ftsmps527,  "vdd-s4"),
+	RPMH_VREG("smps5",  "smp%s5",  &pmic5_ftsmps527,  "vdd-s5"),
+	RPMH_VREG("smps6",  "smp%s6",  &pmic5_ftsmps527,  "vdd-s6"),
+	RPMH_VREG("smps7",  "smp%s7",  &pmic5_ftsmps527,  "vdd-s7"),
+	RPMH_VREG("smps8",  "smp%s8",  &pmic5_ftsmps527,  "vdd-s8"),
+	RPMH_VREG("smps9",  "smp%s9",  &pmic5_ftsmps527,  "vdd-s9"),
+	RPMH_VREG("ldo1",   "ldo%s1",  &pmic5_nldo515,    "vdd-s9"),
+	RPMH_VREG("ldo2",   "ldo%s2",  &pmic5_nldo515,    "vdd-l2-l3"),
+	RPMH_VREG("ldo3",   "ldo%s3",  &pmic5_nldo515,    "vdd-l2-l3"),
+	RPMH_VREG("ldo4",   "ldo%s4",  &pmic5_nldo515,    "vdd-s9"),
+	RPMH_VREG("ldo5",   "ldo%s5",  &pmic5_nldo515,    "vdd-s9"),
+	RPMH_VREG("ldo6",   "ldo%s6",  &pmic5_nldo515,    "vdd-l6-l7"),
+	RPMH_VREG("ldo7",   "ldo%s7",  &pmic5_nldo515,    "vdd-l6-l7"),
+	RPMH_VREG("ldo8",   "ldo%s8",  &pmic5_pldo515_mv, "vdd-l8-l9"),
+	RPMH_VREG("ldo9",   "ldo%s9",  &pmic5_pldo,       "vdd-l8-l9"),
+	{}
+};
+
 static const struct rpmh_vreg_init_data pm8350_vreg_data[] = {
 	RPMH_VREG("smps1",  "smp%s1",  &pmic5_ftsmps510, "vdd-s1"),
 	RPMH_VREG("smps2",  "smp%s2",  &pmic5_ftsmps510, "vdd-s2"),
@@ -1431,6 +1482,10 @@ static const struct of_device_id __maybe_unused rpmh_regulator_match_table[] = {
 		.compatible = "qcom,pmm8155au-rpmh-regulators",
 		.data = pmm8155au_vreg_data,
 	},
+	{
+		.compatible = "qcom,pmm8654au-rpmh-regulators",
+		.data = pmm8654au_vreg_data,
+	},
 	{
 		.compatible = "qcom,pmx55-rpmh-regulators",
 		.data = pmx55_vreg_data,
-- 
2.37.2

Re: [PATCH v3 17/18] regulator: qcom-rpmh: add support for pmm8654au regulators

[Konrad Dybcio]

On 27.03.2023 14:53, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add the RPMH regulators exposed by the PMM8654au PMIC and its variants.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> Cc: Mark Brown <broonie@kernel.org>
> ---
I can't check the validity of the regulator types and ranges, but
for the overall picture:

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  drivers/regulator/qcom-rpmh-regulator.c | 55 +++++++++++++++++++++++++
>  1 file changed, 55 insertions(+)
> 
> diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c
> index 4826d60e5d95..b0a58c62b1e2 100644
> --- a/drivers/regulator/qcom-rpmh-regulator.c
> +++ b/drivers/regulator/qcom-rpmh-regulator.c
> @@ -694,6 +694,16 @@ static const struct rpmh_vreg_hw_data pmic5_pldo_lv = {
>  	.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
>  };
>  
> +static const struct rpmh_vreg_hw_data pmic5_pldo515_mv = {
> +	.regulator_type = VRM,
> +	.ops = &rpmh_regulator_vrm_drms_ops,
> +	.voltage_range = REGULATOR_LINEAR_RANGE(1800000, 0, 187, 8000),
> +	.n_voltages = 188,
> +	.hpm_min_load_uA = 10000,
> +	.pmic_mode_map = pmic_mode_map_pmic5_ldo,
> +	.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> +};
> +
>  static const struct rpmh_vreg_hw_data pmic5_nldo = {
>  	.regulator_type = VRM,
>  	.ops = &rpmh_regulator_vrm_drms_ops,
> @@ -704,6 +714,16 @@ static const struct rpmh_vreg_hw_data pmic5_nldo = {
>  	.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
>  };
>  
> +static const struct rpmh_vreg_hw_data pmic5_nldo515 = {
> +	.regulator_type = VRM,
> +	.ops = &rpmh_regulator_vrm_drms_ops,
> +	.voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 210, 8000),
> +	.n_voltages = 211,
> +	.hpm_min_load_uA = 30000,
> +	.pmic_mode_map = pmic_mode_map_pmic5_ldo,
> +	.of_map_mode = rpmh_regulator_pmic4_ldo_of_map_mode,
> +};
> +
>  static const struct rpmh_vreg_hw_data pmic5_hfsmps510 = {
>  	.regulator_type = VRM,
>  	.ops = &rpmh_regulator_vrm_ops,
> @@ -749,6 +769,15 @@ static const struct rpmh_vreg_hw_data pmic5_ftsmps525_mv = {
>  	.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
>  };
>  
> +static const struct rpmh_vreg_hw_data pmic5_ftsmps527 = {
> +	.regulator_type = VRM,
> +	.ops = &rpmh_regulator_vrm_ops,
> +	.voltage_range = REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
> +	.n_voltages = 215,
> +	.pmic_mode_map = pmic_mode_map_pmic5_smps,
> +	.of_map_mode = rpmh_regulator_pmic4_smps_of_map_mode,
> +};
> +
>  static const struct rpmh_vreg_hw_data pmic5_hfsmps515 = {
>  	.regulator_type = VRM,
>  	.ops = &rpmh_regulator_vrm_ops,
> @@ -937,6 +966,28 @@ static const struct rpmh_vreg_init_data pmm8155au_vreg_data[] = {
>  	{}
>  };
>  
> +static const struct rpmh_vreg_init_data pmm8654au_vreg_data[] = {
> +	RPMH_VREG("smps1",  "smp%s1",  &pmic5_ftsmps527,  "vdd-s1"),
> +	RPMH_VREG("smps2",  "smp%s2",  &pmic5_ftsmps527,  "vdd-s2"),
> +	RPMH_VREG("smps3",  "smp%s3",  &pmic5_ftsmps527,  "vdd-s3"),
> +	RPMH_VREG("smps4",  "smp%s4",  &pmic5_ftsmps527,  "vdd-s4"),
> +	RPMH_VREG("smps5",  "smp%s5",  &pmic5_ftsmps527,  "vdd-s5"),
> +	RPMH_VREG("smps6",  "smp%s6",  &pmic5_ftsmps527,  "vdd-s6"),
> +	RPMH_VREG("smps7",  "smp%s7",  &pmic5_ftsmps527,  "vdd-s7"),
> +	RPMH_VREG("smps8",  "smp%s8",  &pmic5_ftsmps527,  "vdd-s8"),
> +	RPMH_VREG("smps9",  "smp%s9",  &pmic5_ftsmps527,  "vdd-s9"),
> +	RPMH_VREG("ldo1",   "ldo%s1",  &pmic5_nldo515,    "vdd-s9"),
> +	RPMH_VREG("ldo2",   "ldo%s2",  &pmic5_nldo515,    "vdd-l2-l3"),
> +	RPMH_VREG("ldo3",   "ldo%s3",  &pmic5_nldo515,    "vdd-l2-l3"),
> +	RPMH_VREG("ldo4",   "ldo%s4",  &pmic5_nldo515,    "vdd-s9"),
> +	RPMH_VREG("ldo5",   "ldo%s5",  &pmic5_nldo515,    "vdd-s9"),
> +	RPMH_VREG("ldo6",   "ldo%s6",  &pmic5_nldo515,    "vdd-l6-l7"),
> +	RPMH_VREG("ldo7",   "ldo%s7",  &pmic5_nldo515,    "vdd-l6-l7"),
> +	RPMH_VREG("ldo8",   "ldo%s8",  &pmic5_pldo515_mv, "vdd-l8-l9"),
> +	RPMH_VREG("ldo9",   "ldo%s9",  &pmic5_pldo,       "vdd-l8-l9"),
> +	{}
> +};
> +
>  static const struct rpmh_vreg_init_data pm8350_vreg_data[] = {
>  	RPMH_VREG("smps1",  "smp%s1",  &pmic5_ftsmps510, "vdd-s1"),
>  	RPMH_VREG("smps2",  "smp%s2",  &pmic5_ftsmps510, "vdd-s2"),
> @@ -1431,6 +1482,10 @@ static const struct of_device_id __maybe_unused rpmh_regulator_match_table[] = {
>  		.compatible = "qcom,pmm8155au-rpmh-regulators",
>  		.data = pmm8155au_vreg_data,
>  	},
> +	{
> +		.compatible = "qcom,pmm8654au-rpmh-regulators",
> +		.data = pmm8654au_vreg_data,
> +	},
>  	{
>  		.compatible = "qcom,pmx55-rpmh-regulators",
>  		.data = pmx55_vreg_data,

[PATCH v3 18/18] arm64: dts: qcom: sa8775p-ride: add PMIC regulators

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add PMIC regulators for sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 233 ++++++++++++++++++++++
 1 file changed, 233 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
index a0d2024a69df..fdd229d232d1 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
@@ -5,6 +5,8 @@
 
 /dts-v1/;
 
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
 #include "sa8775p.dtsi"
 #include "sa8775p-pmics.dtsi"
 
@@ -25,6 +27,237 @@ chosen {
 	};
 };
 
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmm8654au-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s4a: smps4 {
+			regulator-name = "vreg_s4a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1816000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5a: smps5 {
+			regulator-name = "vreg_s5a";
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1996000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s9a: smps9 {
+			regulator-name = "vreg_s9a";
+			regulator-min-microvolt = <535000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4a: ldo4 {
+			regulator-name = "vreg_l4a";
+			regulator-min-microvolt = <788000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-name = "vreg_l5a";
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a: ldo6 {
+			regulator-name = "vreg_l6a";
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-name = "vreg_l7a";
+			regulator-min-microvolt = <720000>;
+			regulator-max-microvolt = <950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a: ldo8 {
+			regulator-name = "vreg_l8a";
+			regulator-min-microvolt = <2400000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a: ldo9 {
+			regulator-name = "vreg_l9a";
+			regulator-min-microvolt = <2970000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pmm8654au-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <1140000>;
+			regulator-max-microvolt = <1260000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c: ldo2 {
+			regulator-name = "vreg_l2c";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c: ldo3 {
+			regulator-name = "vreg_l3c";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c: ldo4 {
+			regulator-name = "vreg_l4c";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			/*
+			 * FIXME: This should have regulator-allow-set-load but
+			 * we're getting the over-current fault from the PMIC
+			 * when switching to LPM.
+			 */
+		};
+
+		vreg_l5c: ldo5 {
+			regulator-name = "vreg_l5c";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c: ldo6 {
+			regulator-name = "vreg_l6c";
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-name = "vreg_l7c";
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c: ldo8 {
+			regulator-name = "vreg_l8c";
+			regulator-min-microvolt = <2400000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c: ldo9 {
+			regulator-name = "vreg_l9c";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <2700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmm8654au-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vreg_s4e: smps4 {
+			regulator-name = "vreg_s4e";
+			regulator-min-microvolt = <970000>;
+			regulator-max-microvolt = <1520000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s7e: smps7 {
+			regulator-name = "vreg_s7e";
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1170000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s9e: smps9 {
+			regulator-name = "vreg_s9e";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <570000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6e: ldo6 {
+			regulator-name = "vreg_l6e";
+			regulator-min-microvolt = <1280000>;
+			regulator-max-microvolt = <1450000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8e: ldo8 {
+			regulator-name = "vreg_l8e";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
 &i2c18 {
 	clock-frequency = <400000>;
 	pinctrl-0 = <&qup_i2c18_default>;
-- 
2.37.2

Re: [PATCH v3 18/18] arm64: dts: qcom: sa8775p-ride: add PMIC regulators

[Shazad Hussain]

On 3/27/2023 6:23 PM, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add PMIC regulators for sa8775p-ride.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 233 ++++++++++++++++++++++
>   1 file changed, 233 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> index a0d2024a69df..fdd229d232d1 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> @@ -5,6 +5,8 @@
>   
>   /dts-v1/;
>   
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +
>   #include "sa8775p.dtsi"
>   #include "sa8775p-pmics.dtsi"
>   
> @@ -25,6 +27,237 @@ chosen {
>   	};
>   };
>   
> +&apps_rsc {
> +	regulators-0 {
> +		compatible = "qcom,pmm8654au-rpmh-regulators";
> +		qcom,pmic-id = "a";
> +
> +		vreg_s4a: smps4 {
> +			regulator-name = "vreg_s4a";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1816000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s5a: smps5 {
> +			regulator-name = "vreg_s5a";
> +			regulator-min-microvolt = <1850000>;
> +			regulator-max-microvolt = <1996000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s9a: smps9 {
> +			regulator-name = "vreg_s9a";
> +			regulator-min-microvolt = <535000>;
> +			regulator-max-microvolt = <1120000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l4a: ldo4 {
> +			regulator-name = "vreg_l4a";
> +			regulator-min-microvolt = <788000>;
> +			regulator-max-microvolt = <1050000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l5a: ldo5 {
> +			regulator-name = "vreg_l5a";
> +			regulator-min-microvolt = <870000>;
> +			regulator-max-microvolt = <950000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l6a: ldo6 {
> +			regulator-name = "vreg_l6a";
> +			regulator-min-microvolt = <870000>;
> +			regulator-max-microvolt = <970000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7a: ldo7 {
> +			regulator-name = "vreg_l7a";
> +			regulator-min-microvolt = <720000>;
> +			regulator-max-microvolt = <950000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8a: ldo8 {
> +			regulator-name = "vreg_l8a";
> +			regulator-min-microvolt = <2400000>;

Hi Bart,
Internally with PMIC2.0 i.e K2 upgraded board we were seeing target
crash when kernel votes for 2.4V with fault monitors enabled in K2.
So let's keep the recommended value <2504000> for ldo8.

-Shazad

> +			regulator-max-microvolt = <3300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l9a: ldo9 {
> +			regulator-name = "vreg_l9a";
> +			regulator-min-microvolt = <2970000>;
> +			regulator-max-microvolt = <3544000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-1 {
> +		compatible = "qcom,pmm8654au-rpmh-regulators";
> +		qcom,pmic-id = "c";
> +
> +		vreg_l1c: ldo1 {
> +			regulator-name = "vreg_l1c";
> +			regulator-min-microvolt = <1140000>;
> +			regulator-max-microvolt = <1260000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2c: ldo2 {
> +			regulator-name = "vreg_l2c";
> +			regulator-min-microvolt = <900000>;
> +			regulator-max-microvolt = <1100000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l3c: ldo3 {
> +			regulator-name = "vreg_l3c";
> +			regulator-min-microvolt = <1100000>;
> +			regulator-max-microvolt = <1300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l4c: ldo4 {
> +			regulator-name = "vreg_l4c";
> +			regulator-min-microvolt = <1100000>;
> +			regulator-max-microvolt = <1300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			/*
> +			 * FIXME: This should have regulator-allow-set-load but
> +			 * we're getting the over-current fault from the PMIC
> +			 * when switching to LPM.
> +			 */
> +		};
> +
> +		vreg_l5c: ldo5 {
> +			regulator-name = "vreg_l5c";
> +			regulator-min-microvolt = <1100000>;
> +			regulator-max-microvolt = <1300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l6c: ldo6 {
> +			regulator-name = "vreg_l6c";
> +			regulator-min-microvolt = <1620000>;
> +			regulator-max-microvolt = <1980000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7c: ldo7 {
> +			regulator-name = "vreg_l7c";
> +			regulator-min-microvolt = <1620000>;
> +			regulator-max-microvolt = <2000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8c: ldo8 {
> +			regulator-name = "vreg_l8c";
> +			regulator-min-microvolt = <2400000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l9c: ldo9 {
> +			regulator-name = "vreg_l9c";
> +			regulator-min-microvolt = <1650000>;
> +			regulator-max-microvolt = <2700000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-2 {
> +		compatible = "qcom,pmm8654au-rpmh-regulators";
> +		qcom,pmic-id = "e";
> +
> +		vreg_s4e: smps4 {
> +			regulator-name = "vreg_s4e";
> +			regulator-min-microvolt = <970000>;
> +			regulator-max-microvolt = <1520000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s7e: smps7 {
> +			regulator-name = "vreg_s7e";
> +			regulator-min-microvolt = <1010000>;
> +			regulator-max-microvolt = <1170000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s9e: smps9 {
> +			regulator-name = "vreg_s9e";
> +			regulator-min-microvolt = <300000>;
> +			regulator-max-microvolt = <570000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l6e: ldo6 {
> +			regulator-name = "vreg_l6e";
> +			regulator-min-microvolt = <1280000>;
> +			regulator-max-microvolt = <1450000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8e: ldo8 {
> +			regulator-name = "vreg_l8e";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1950000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +};
> +
>   &i2c18 {
>   	clock-frequency = <400000>;
>   	pinctrl-0 = <&qup_i2c18_default>;

Re: (subset) [PATCH v3 00/18] arm64: dts: qcom: sa8775p: add basic PMIC support

[Bjorn Andersson]

On Mon, 27 Mar 2023 14:52:58 +0200, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> This adds support for a number of PMIC functionalities on sa8775p. The PMIC
> used on the reference board is pm8654au which is another variant of the SPMI
> PMIC from Qualcomm with an automotive twist.
> 
> v2 -> v3:
> - add GPIO line names for the PMIC GPIOs on sa8775p-ride
> - add missing GPIO chips to the PMIC .dtsi
> - add missing thermal zones and alerts
> - add regulators (driver support and regulator settings for sa8775p-ride)
> - add missing PDC mappings
> - squash patches 7 and 8 to avoid adding code without users
> - dropped Krzysztof's Ack from patch 3 as it now extends the max number of
>   mappings so most likely needs a second look
> 
> [...]

Applied, thanks!

[01/18] arm64: dts: qcom: sa8775p: pad reg properties to 8 digits
        commit: 3fd7e2eec8f4fedbe3b252cf436be8527f7a5f82
[02/18] arm64: dts: qcom: sa8775p: sort soc nodes by reg property
        commit: f95f988cf7b609157630dd1f2f7e8d297aadbe2b
[04/18] arm64: dts: qcom: sa8775p: add the pdc node
        commit: 8696cd072e955bd6f5df757774e47f0b9dd29920
[05/18] arm64: dts: qcom: sa8775p: add the spmi node
        commit: fdd55b3babedce5abd1c1f90afc3ab2199a772ad
[07/18] arm64: dts: qcom: sa8775p: add support for the on-board PMICs
        commit: 634a3de323fc5c67c144919e298259d8d9d44a4b
[08/18] arm64: dts: qcom: sa8775p: add the Power On device node
        commit: d2d9a592746cd454bd5b8f72193f2d3db2e62a44
[09/18] arm64: dts: qcom: sa8775p: pmic: add the power key
        commit: b3a755ba16e6f61d93c811b827edacc9946b0500
[10/18] arm64: dts: qcom: sa8775p: pmic: add support for the pmm8654 RESIN input
        commit: cecff1f5429d975df9649376e2bd5a2fb004f988
[11/18] arm64: dts: qcom: sa8775p: pmic: add thermal zones
        commit: fa40ca07e943333a14d247988ef5008a59949153
[14/18] arm64: dts: qcom: sa8775p: add PMIC GPIO controller nodes
        commit: e5a893a7cec5776e10c25d7fa80b5ad1edf88c17
[15/18] arm64: dts: qcom: sa8775p-ride: set gpio-line-names for PMIC GPIOs
        commit: 81767c1591dcb711f1f78a80e510b667b1fb5718

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>