[PATCH net-next v11 0/9] TXGBE PHYLINK support

[PATCH net-next v11 0/9] TXGBE PHYLINK support

[Jiawen Wu]

Implement I2C, SFP, GPIO and PHYLINK to setup TXGBE link.

Because our I2C and PCS are based on Synopsys Designware IP-core, extend
the i2c-designware and pcs-xpcs driver to realize our functions.

v10 -> v11:
- add gc->label NULL check
- rebase on merging of wangxun patches

v9 -> v10:
- clear I2C device model flags
- change the order of header files
- use xpcs_create_mdiodev()
- fix Kconfig warning

v8 -> v9:
- rename swnode property for specific I2C platform device
- add ".fast_io = true" for I2C regmap
- use raw_spinlock_t for GPIO reg lock and adjust its position
- remove redundant txgbe->mdiodev
- keep reverse x-mass tree order
- other minor style changes

v7 -> v8:
- use macro defined I2C FIFO depth instead of magic number
- fix return code of clock create failure
- add spinlock for writing GPIO registers
- implement triggering GPIO interrupts for both-edge type
- remove the condition that enables interrupts
- add mii bus check for PCS device
- other minor style changes

v6 -> v7:
- change swnode property of I2C platform to be boolean
- use device_property_present() to match I2C device data

v5 -> v6:
- fix to set error code if pointer of txgbe is NULL
- change "if" to "switch" for *_i2c_dw_xfer_quirk()
- rename property for I2C device flag
- use regmap to access I2C mem region
- use DEFINE_RES_IRQ()
- use phylink_mii_c45_pcs_get_state() for DW_XPCS_10GBASER

v4 -> v5:
- add clock register
- delete i2c-dw.h with platform data
- introduce property "i2c-dw-flags" to match device flags
- get resource from platform info to do ioremap
- rename quirk functions in i2c-designware-*.c
- fix calling txgbe_phylink_init()

v3 -> v4:
- modify I2C transfer to be generic implementation
- avoid to read DW_IC_COMP_PARAM_1
- remove redundant "if" statement
- add specific labels to handle error in txgbe_init_phy(), and remove
  "if" conditions in txgbe_remove_phy()

v2 -> v3:
- delete own I2C bus master driver, support it in i2c-designware
- delete own PCS functions, remove pma configuration and 1000BASE-X mode
- add basic function for 10GBASE-R interface in pcs-xpcs
- add helper to get txgbe pointer from netdev

v1 -> v2:
- add comments to indicate GPIO lines
- add I2C write operation support
- modify GPIO direction functions
- rename functions related to PHY interface
- add condition on interface changing to re-config PCS
- add to set advertise and fix to get status for 1000BASE-X mode
- other redundant codes remove

Jiawen Wu (9):
  net: txgbe: Add software nodes to support phylink
  i2c: designware: Add driver support for Wangxun 10Gb NIC
  net: txgbe: Register fixed rate clock
  net: txgbe: Register I2C platform device
  net: txgbe: Add SFP module identify
  net: txgbe: Support GPIO to SFP socket
  net: pcs: Add 10GBASE-R mode for Synopsys Designware XPCS
  net: txgbe: Implement phylink pcs
  net: txgbe: Support phylink MAC layer

 drivers/i2c/busses/i2c-designware-common.c    |   8 +
 drivers/i2c/busses/i2c-designware-core.h      |   4 +
 drivers/i2c/busses/i2c-designware-master.c    |  89 ++-
 drivers/i2c/busses/i2c-designware-platdrv.c   |  15 +
 drivers/net/ethernet/wangxun/Kconfig          |  10 +
 drivers/net/ethernet/wangxun/libwx/wx_lib.c   |   3 +-
 drivers/net/ethernet/wangxun/libwx/wx_type.h  |   4 +
 drivers/net/ethernet/wangxun/txgbe/Makefile   |   1 +
 .../ethernet/wangxun/txgbe/txgbe_ethtool.c    |  28 +
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   |  65 +-
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 673 ++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_phy.h    |  10 +
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  89 +++
 drivers/net/pcs/pcs-xpcs.c                    |  30 +
 include/linux/pcs/pcs-xpcs.h                  |   1 +
 15 files changed, 992 insertions(+), 38 deletions(-)
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h

-- 
2.27.0

[PATCH net-next v11 1/9] net: txgbe: Add software nodes to support phylink

[Jiawen Wu]

Register software nodes for GPIO, I2C, SFP and PHYLINK. Define the
device properties.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
---
 drivers/net/ethernet/wangxun/libwx/wx_type.h  |  1 +
 drivers/net/ethernet/wangxun/txgbe/Makefile   |  1 +
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   | 22 ++++-
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 89 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_phy.h    | 10 +++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   | 49 ++++++++++
 6 files changed, 171 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h

diff --git a/drivers/net/ethernet/wangxun/libwx/wx_type.h b/drivers/net/ethernet/wangxun/libwx/wx_type.h
index 5063846e1b52..c61c18a842c4 100644
--- a/drivers/net/ethernet/wangxun/libwx/wx_type.h
+++ b/drivers/net/ethernet/wangxun/libwx/wx_type.h
@@ -814,6 +814,7 @@ enum wx_isb_idx {
 struct wx {
 	unsigned long active_vlans[BITS_TO_LONGS(VLAN_N_VID)];
 
+	void *priv;
 	u8 __iomem *hw_addr;
 	struct pci_dev *pdev;
 	struct net_device *netdev;
diff --git a/drivers/net/ethernet/wangxun/txgbe/Makefile b/drivers/net/ethernet/wangxun/txgbe/Makefile
index 6db14a2cb2d0..7507f762edfe 100644
--- a/drivers/net/ethernet/wangxun/txgbe/Makefile
+++ b/drivers/net/ethernet/wangxun/txgbe/Makefile
@@ -8,4 +8,5 @@ obj-$(CONFIG_TXGBE) += txgbe.o
 
 txgbe-objs := txgbe_main.o \
               txgbe_hw.o \
+              txgbe_phy.o \
               txgbe_ethtool.o
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
index 0f0d9fa1cde1..2335fa863fa5 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
@@ -15,6 +15,7 @@
 #include "../libwx/wx_hw.h"
 #include "txgbe_type.h"
 #include "txgbe_hw.h"
+#include "txgbe_phy.h"
 #include "txgbe_ethtool.h"
 
 char txgbe_driver_name[] = "txgbe";
@@ -518,6 +519,7 @@ static int txgbe_probe(struct pci_dev *pdev,
 	struct net_device *netdev;
 	int err, expected_gts;
 	struct wx *wx = NULL;
+	struct txgbe *txgbe;
 
 	u16 eeprom_verh = 0, eeprom_verl = 0, offset = 0;
 	u16 eeprom_cfg_blkh = 0, eeprom_cfg_blkl = 0;
@@ -682,10 +684,23 @@ static int txgbe_probe(struct pci_dev *pdev,
 			 "0x%08x", etrack_id);
 	}
 
-	err = register_netdev(netdev);
+	txgbe = devm_kzalloc(&pdev->dev, sizeof(*txgbe), GFP_KERNEL);
+	if (!txgbe) {
+		err = -ENOMEM;
+		goto err_release_hw;
+	}
+
+	txgbe->wx = wx;
+	wx->priv = txgbe;
+
+	err = txgbe_init_phy(txgbe);
 	if (err)
 		goto err_release_hw;
 
+	err = register_netdev(netdev);
+	if (err)
+		goto err_remove_phy;
+
 	pci_set_drvdata(pdev, wx);
 
 	netif_tx_stop_all_queues(netdev);
@@ -713,6 +728,8 @@ static int txgbe_probe(struct pci_dev *pdev,
 
 	return 0;
 
+err_remove_phy:
+	txgbe_remove_phy(txgbe);
 err_release_hw:
 	wx_clear_interrupt_scheme(wx);
 	wx_control_hw(wx, false);
@@ -738,11 +755,14 @@ static int txgbe_probe(struct pci_dev *pdev,
 static void txgbe_remove(struct pci_dev *pdev)
 {
 	struct wx *wx = pci_get_drvdata(pdev);
+	struct txgbe *txgbe = wx->priv;
 	struct net_device *netdev;
 
 	netdev = wx->netdev;
 	unregister_netdev(netdev);
 
+	txgbe_remove_phy(txgbe);
+
 	pci_release_selected_regions(pdev,
 				     pci_select_bars(pdev, IORESOURCE_MEM));
 
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
new file mode 100644
index 000000000000..be4b5ad74a3c
--- /dev/null
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
+
+#include <linux/gpio/property.h>
+#include <linux/i2c.h>
+#include <linux/pci.h>
+
+#include "../libwx/wx_type.h"
+#include "txgbe_type.h"
+#include "txgbe_phy.h"
+
+static int txgbe_swnodes_register(struct txgbe *txgbe)
+{
+	struct txgbe_nodes *nodes = &txgbe->nodes;
+	struct pci_dev *pdev = txgbe->wx->pdev;
+	struct software_node *swnodes;
+	u32 id;
+
+	id = (pdev->bus->number << 8) | pdev->devfn;
+
+	snprintf(nodes->gpio_name, sizeof(nodes->gpio_name), "txgbe_gpio-%x", id);
+	snprintf(nodes->i2c_name, sizeof(nodes->i2c_name), "txgbe_i2c-%x", id);
+	snprintf(nodes->sfp_name, sizeof(nodes->sfp_name), "txgbe_sfp-%x", id);
+	snprintf(nodes->phylink_name, sizeof(nodes->phylink_name), "txgbe_phylink-%x", id);
+
+	swnodes = nodes->swnodes;
+
+	/* GPIO 0: tx fault
+	 * GPIO 1: tx disable
+	 * GPIO 2: sfp module absent
+	 * GPIO 3: rx signal lost
+	 * GPIO 4: rate select, 1G(0) 10G(1)
+	 * GPIO 5: rate select, 1G(0) 10G(1)
+	 */
+	nodes->gpio_props[0] = PROPERTY_ENTRY_STRING("pinctrl-names", "default");
+	swnodes[SWNODE_GPIO] = NODE_PROP(nodes->gpio_name, nodes->gpio_props);
+	nodes->gpio0_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 0, GPIO_ACTIVE_HIGH);
+	nodes->gpio1_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 1, GPIO_ACTIVE_HIGH);
+	nodes->gpio2_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 2, GPIO_ACTIVE_LOW);
+	nodes->gpio3_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 3, GPIO_ACTIVE_HIGH);
+	nodes->gpio4_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 4, GPIO_ACTIVE_HIGH);
+	nodes->gpio5_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 5, GPIO_ACTIVE_HIGH);
+
+	nodes->i2c_props[0] = PROPERTY_ENTRY_STRING("compatible", "snps,designware-i2c");
+	nodes->i2c_props[1] = PROPERTY_ENTRY_BOOL("wx,i2c-snps-model");
+	nodes->i2c_props[2] = PROPERTY_ENTRY_U32("clock-frequency", I2C_MAX_STANDARD_MODE_FREQ);
+	swnodes[SWNODE_I2C] = NODE_PROP(nodes->i2c_name, nodes->i2c_props);
+	nodes->i2c_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_I2C]);
+
+	nodes->sfp_props[0] = PROPERTY_ENTRY_STRING("compatible", "sff,sfp");
+	nodes->sfp_props[1] = PROPERTY_ENTRY_REF_ARRAY("i2c-bus", nodes->i2c_ref);
+	nodes->sfp_props[2] = PROPERTY_ENTRY_REF_ARRAY("tx-fault-gpios", nodes->gpio0_ref);
+	nodes->sfp_props[3] = PROPERTY_ENTRY_REF_ARRAY("tx-disable-gpios", nodes->gpio1_ref);
+	nodes->sfp_props[4] = PROPERTY_ENTRY_REF_ARRAY("mod-def0-gpios", nodes->gpio2_ref);
+	nodes->sfp_props[5] = PROPERTY_ENTRY_REF_ARRAY("los-gpios", nodes->gpio3_ref);
+	nodes->sfp_props[6] = PROPERTY_ENTRY_REF_ARRAY("rate-select1-gpios", nodes->gpio4_ref);
+	nodes->sfp_props[7] = PROPERTY_ENTRY_REF_ARRAY("rate-select0-gpios", nodes->gpio5_ref);
+	swnodes[SWNODE_SFP] = NODE_PROP(nodes->sfp_name, nodes->sfp_props);
+	nodes->sfp_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_SFP]);
+
+	nodes->phylink_props[0] = PROPERTY_ENTRY_STRING("managed", "in-band-status");
+	nodes->phylink_props[1] = PROPERTY_ENTRY_REF_ARRAY("sfp", nodes->sfp_ref);
+	swnodes[SWNODE_PHYLINK] = NODE_PROP(nodes->phylink_name, nodes->phylink_props);
+
+	nodes->group[SWNODE_GPIO] = &swnodes[SWNODE_GPIO];
+	nodes->group[SWNODE_I2C] = &swnodes[SWNODE_I2C];
+	nodes->group[SWNODE_SFP] = &swnodes[SWNODE_SFP];
+	nodes->group[SWNODE_PHYLINK] = &swnodes[SWNODE_PHYLINK];
+
+	return software_node_register_node_group(nodes->group);
+}
+
+int txgbe_init_phy(struct txgbe *txgbe)
+{
+	int ret;
+
+	ret = txgbe_swnodes_register(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to register software nodes\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+void txgbe_remove_phy(struct txgbe *txgbe)
+{
+	software_node_unregister_node_group(txgbe->nodes.group);
+}
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h
new file mode 100644
index 000000000000..1ab592124986
--- /dev/null
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
+
+#ifndef _TXGBE_PHY_H_
+#define _TXGBE_PHY_H_
+
+int txgbe_init_phy(struct txgbe *txgbe);
+void txgbe_remove_phy(struct txgbe *txgbe);
+
+#endif /* _TXGBE_NODE_H_ */
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 032972369965..9aa399acd9a0 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -4,6 +4,8 @@
 #ifndef _TXGBE_TYPE_H_
 #define _TXGBE_TYPE_H_
 
+#include <linux/property.h>
+
 /* Device IDs */
 #define TXGBE_DEV_ID_SP1000                     0x1001
 #define TXGBE_DEV_ID_WX1820                     0x2001
@@ -100,4 +102,51 @@
 
 extern char txgbe_driver_name[];
 
+static inline struct txgbe *netdev_to_txgbe(struct net_device *netdev)
+{
+	struct wx *wx = netdev_priv(netdev);
+
+	return wx->priv;
+}
+
+#define NODE_PROP(_NAME, _PROP)			\
+	(const struct software_node) {		\
+		.name = _NAME,			\
+		.properties = _PROP,		\
+	}
+
+enum txgbe_swnodes {
+	SWNODE_GPIO = 0,
+	SWNODE_I2C,
+	SWNODE_SFP,
+	SWNODE_PHYLINK,
+	SWNODE_MAX
+};
+
+struct txgbe_nodes {
+	char gpio_name[32];
+	char i2c_name[32];
+	char sfp_name[32];
+	char phylink_name[32];
+	struct property_entry gpio_props[1];
+	struct property_entry i2c_props[3];
+	struct property_entry sfp_props[8];
+	struct property_entry phylink_props[2];
+	struct software_node_ref_args i2c_ref[1];
+	struct software_node_ref_args gpio0_ref[1];
+	struct software_node_ref_args gpio1_ref[1];
+	struct software_node_ref_args gpio2_ref[1];
+	struct software_node_ref_args gpio3_ref[1];
+	struct software_node_ref_args gpio4_ref[1];
+	struct software_node_ref_args gpio5_ref[1];
+	struct software_node_ref_args sfp_ref[1];
+	struct software_node swnodes[SWNODE_MAX];
+	const struct software_node *group[SWNODE_MAX + 1];
+};
+
+struct txgbe {
+	struct wx *wx;
+	struct txgbe_nodes nodes;
+};
+
 #endif /* _TXGBE_TYPE_H_ */
-- 
2.27.0

[PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jiawen Wu]

Wangxun 10Gb ethernet chip is connected to Designware I2C, to communicate
with SFP.

Introduce the property "wx,i2c-snps-model" to match device data for Wangxun
in software node case. Since IO resource was mapped on the ethernet driver,
add a model quirk to get regmap from parent device.

The exists IP limitations are dealt as workarounds:
- IP does not support interrupt mode, it works on polling mode.
- Additionally set FIFO depth address the chip issue.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
 drivers/i2c/busses/i2c-designware-common.c  |  8 ++
 drivers/i2c/busses/i2c-designware-core.h    |  4 +
 drivers/i2c/busses/i2c-designware-master.c  | 89 +++++++++++++++++++--
 drivers/i2c/busses/i2c-designware-platdrv.c | 15 ++++
 4 files changed, 111 insertions(+), 5 deletions(-)

diff --git a/drivers/i2c/busses/i2c-designware-common.c b/drivers/i2c/busses/i2c-designware-common.c
index 0dc6b1ce663f..cdd8c67d9129 100644
--- a/drivers/i2c/busses/i2c-designware-common.c
+++ b/drivers/i2c/busses/i2c-designware-common.c
@@ -575,6 +575,14 @@ int i2c_dw_set_fifo_size(struct dw_i2c_dev *dev)
 	unsigned int param;
 	int ret;
 
+	/* DW_IC_COMP_PARAM_1 not implement for IP issue */
+	if ((dev->flags & MODEL_MASK) == MODEL_WANGXUN_SP) {
+		dev->tx_fifo_depth = TXGBE_TX_FIFO_DEPTH;
+		dev->rx_fifo_depth = TXGBE_RX_FIFO_DEPTH;
+
+		return 0;
+	}
+
 	/*
 	 * Try to detect the FIFO depth if not set by interface driver,
 	 * the depth could be from 2 to 256 from HW spec.
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index c5d87aae39c6..782532c20bd1 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -303,6 +303,7 @@ struct dw_i2c_dev {
 #define MODEL_MSCC_OCELOT			BIT(8)
 #define MODEL_BAIKAL_BT1			BIT(9)
 #define MODEL_AMD_NAVI_GPU			BIT(10)
+#define MODEL_WANGXUN_SP			BIT(11)
 #define MODEL_MASK				GENMASK(11, 8)
 
 /*
@@ -312,6 +313,9 @@ struct dw_i2c_dev {
 #define AMD_UCSI_INTR_REG			0x474
 #define AMD_UCSI_INTR_EN			0xd
 
+#define TXGBE_TX_FIFO_DEPTH			4
+#define TXGBE_RX_FIFO_DEPTH			0
+
 struct i2c_dw_semaphore_callbacks {
 	int	(*probe)(struct dw_i2c_dev *dev);
 	void	(*remove)(struct dw_i2c_dev *dev);
diff --git a/drivers/i2c/busses/i2c-designware-master.c b/drivers/i2c/busses/i2c-designware-master.c
index 55ea91a63382..3bfd7a2232db 100644
--- a/drivers/i2c/busses/i2c-designware-master.c
+++ b/drivers/i2c/busses/i2c-designware-master.c
@@ -354,6 +354,68 @@ static int amd_i2c_dw_xfer_quirk(struct i2c_adapter *adap, struct i2c_msg *msgs,
 	return 0;
 }
 
+static int i2c_dw_poll_tx_empty(struct dw_i2c_dev *dev)
+{
+	u32 val;
+
+	return regmap_read_poll_timeout(dev->map, DW_IC_RAW_INTR_STAT, val,
+					val & DW_IC_INTR_TX_EMPTY,
+					100, 1000);
+}
+
+static int i2c_dw_poll_rx_full(struct dw_i2c_dev *dev)
+{
+	u32 val;
+
+	return regmap_read_poll_timeout(dev->map, DW_IC_RAW_INTR_STAT, val,
+					val & DW_IC_INTR_RX_FULL,
+					100, 1000);
+}
+
+static int txgbe_i2c_dw_xfer_quirk(struct i2c_adapter *adap, struct i2c_msg *msgs,
+				   int num_msgs)
+{
+	struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
+	int msg_idx, buf_len, data_idx, ret;
+	unsigned int val, stop = 0;
+	u8 *buf;
+
+	dev->msgs = msgs;
+	dev->msgs_num = num_msgs;
+	i2c_dw_xfer_init(dev);
+	regmap_write(dev->map, DW_IC_INTR_MASK, 0);
+
+	for (msg_idx = 0; msg_idx < num_msgs; msg_idx++) {
+		buf = msgs[msg_idx].buf;
+		buf_len = msgs[msg_idx].len;
+
+		for (data_idx = 0; data_idx < buf_len; data_idx++) {
+			if (msg_idx == num_msgs - 1 && data_idx == buf_len - 1)
+				stop |= BIT(9);
+
+			if (msgs[msg_idx].flags & I2C_M_RD) {
+				regmap_write(dev->map, DW_IC_DATA_CMD, 0x100 | stop);
+
+				ret = i2c_dw_poll_rx_full(dev);
+				if (ret)
+					return ret;
+
+				regmap_read(dev->map, DW_IC_DATA_CMD, &val);
+				buf[data_idx] = val;
+			} else {
+				ret = i2c_dw_poll_tx_empty(dev);
+				if (ret)
+					return ret;
+
+				regmap_write(dev->map, DW_IC_DATA_CMD,
+					     buf[data_idx] | stop);
+			}
+		}
+	}
+
+	return num_msgs;
+}
+
 /*
  * Initiate (and continue) low level master read/write transaction.
  * This function is only called from i2c_dw_isr, and pumping i2c_msg
@@ -559,13 +621,19 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 	pm_runtime_get_sync(dev->dev);
 
 	/*
-	 * Initiate I2C message transfer when AMD NAVI GPU card is enabled,
+	 * Initiate I2C message transfer when polling mode is enabled,
 	 * As it is polling based transfer mechanism, which does not support
 	 * interrupt based functionalities of existing DesignWare driver.
 	 */
-	if ((dev->flags & MODEL_MASK) == MODEL_AMD_NAVI_GPU) {
+	switch (dev->flags & MODEL_MASK) {
+	case MODEL_AMD_NAVI_GPU:
 		ret = amd_i2c_dw_xfer_quirk(adap, msgs, num);
 		goto done_nolock;
+	case MODEL_WANGXUN_SP:
+		ret = txgbe_i2c_dw_xfer_quirk(adap, msgs, num);
+		goto done_nolock;
+	default:
+		break;
 	}
 
 	reinit_completion(&dev->cmd_complete);
@@ -848,7 +916,7 @@ static int i2c_dw_init_recovery_info(struct dw_i2c_dev *dev)
 	return 0;
 }
 
-static int amd_i2c_adap_quirk(struct dw_i2c_dev *dev)
+static int i2c_dw_poll_adap_quirk(struct dw_i2c_dev *dev)
 {
 	struct i2c_adapter *adap = &dev->adapter;
 	int ret;
@@ -862,6 +930,17 @@ static int amd_i2c_adap_quirk(struct dw_i2c_dev *dev)
 	return ret;
 }
 
+static bool i2c_dw_is_model_poll(struct dw_i2c_dev *dev)
+{
+	switch (dev->flags & MODEL_MASK) {
+	case MODEL_AMD_NAVI_GPU:
+	case MODEL_WANGXUN_SP:
+		return true;
+	default:
+		return false;
+	}
+}
+
 int i2c_dw_probe_master(struct dw_i2c_dev *dev)
 {
 	struct i2c_adapter *adap = &dev->adapter;
@@ -917,8 +996,8 @@ int i2c_dw_probe_master(struct dw_i2c_dev *dev)
 	adap->dev.parent = dev->dev;
 	i2c_set_adapdata(adap, dev);
 
-	if ((dev->flags & MODEL_MASK) == MODEL_AMD_NAVI_GPU)
-		return amd_i2c_adap_quirk(dev);
+	if (i2c_dw_is_model_poll(dev))
+		return i2c_dw_poll_adap_quirk(dev);
 
 	if (dev->flags & ACCESS_NO_IRQ_SUSPEND) {
 		irq_flags = IRQF_NO_SUSPEND;
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 89ad88c54754..5a476a38b52f 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -168,6 +168,15 @@ static inline int dw_i2c_of_configure(struct platform_device *pdev)
 }
 #endif
 
+static int txgbe_i2c_request_regs(struct dw_i2c_dev *dev)
+{
+	dev->map = dev_get_regmap(dev->dev->parent, NULL);
+	if (!dev->map)
+		return -ENODEV;
+
+	return 0;
+}
+
 static void dw_i2c_plat_pm_cleanup(struct dw_i2c_dev *dev)
 {
 	pm_runtime_disable(dev->dev);
@@ -185,6 +194,9 @@ static int dw_i2c_plat_request_regs(struct dw_i2c_dev *dev)
 	case MODEL_BAIKAL_BT1:
 		ret = bt1_i2c_request_regs(dev);
 		break;
+	case MODEL_WANGXUN_SP:
+		ret = txgbe_i2c_request_regs(dev);
+		break;
 	default:
 		dev->base = devm_platform_ioremap_resource(pdev, 0);
 		ret = PTR_ERR_OR_ZERO(dev->base);
@@ -277,6 +289,9 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	dev->flags = (uintptr_t)device_get_match_data(&pdev->dev);
+	if (device_property_present(&pdev->dev, "wx,i2c-snps-model"))
+		dev->flags = MODEL_WANGXUN_SP;
+
 	dev->dev = &pdev->dev;
 	dev->irq = irq;
 	platform_set_drvdata(pdev, dev);
-- 
2.27.0

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 469 bytes --]

Hi,

On Mon, Jun 05, 2023 at 10:52:04AM +0800, Jiawen Wu wrote:
> Wangxun 10Gb ethernet chip is connected to Designware I2C, to communicate
> with SFP.
> 
> Introduce the property "wx,i2c-snps-model" to match device data for Wangxun

Does this not need some binding documentation somewhere?

> in software node case. Since IO resource was mapped on the ethernet driver,
> add a model quirk to get regmap from parent device.

All the best,

   Wolfram


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

RE: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jiawen Wu]

On Monday, June 5, 2023 3:02 PM, Wolfram Sang wrote:
> Hi,
> 
> On Mon, Jun 05, 2023 at 10:52:04AM +0800, Jiawen Wu wrote:
> > Wangxun 10Gb ethernet chip is connected to Designware I2C, to communicate
> > with SFP.
> >
> > Introduce the property "wx,i2c-snps-model" to match device data for Wangxun
> 
> Does this not need some binding documentation somewhere?

Do you mean the device tree binding? This property in only used in case of software
node, for wangxun Soc, which has no device tree structure.

> 
> > in software node case. Since IO resource was mapped on the ethernet driver,
> > add a model quirk to get regmap from parent device.
> 
> All the best,
> 
>    Wolfram

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

['Wolfram Sang']

[-- Attachment #1: Type: text/plain, Size: 513 bytes --]


> Do you mean the device tree binding? This property in only used in case of software
> node, for wangxun Soc, which has no device tree structure.

I see, thanks.

How is the dependency of these patches? I'd like to take this patch via
the i2c tree if possible. I guess the other patches will build even if
this patch is not in the net-tree? Or do we need an immutable branch? Or
is it really better if all goes in via net? We might get merge conflicts
then, though. There are other designware patches pending.


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

RE: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jiawen Wu]

On Monday, June 5, 2023 3:53 PM, Wolfram Sang wrote:
> > Do you mean the device tree binding? This property in only used in case of software
> > node, for wangxun Soc, which has no device tree structure.
> 
> I see, thanks.
> 
> How is the dependency of these patches? I'd like to take this patch via
> the i2c tree if possible. I guess the other patches will build even if
> this patch is not in the net-tree? Or do we need an immutable branch? Or
> is it really better if all goes in via net? We might get merge conflicts
> then, though. There are other designware patches pending.


Yes, other patches will build even without this patch. But SFP will not work.
This patch series implement I2C, GPIO, SFP and PHYLINK. The support of SFP
is dependent on I2C and GPIO. If these patches will be end up merging in the
same upstream version, it's not a problem to merge them in different trees,
I think.

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

['Wolfram Sang']

[-- Attachment #1: Type: text/plain, Size: 387 bytes --]


> Yes, other patches will build even without this patch. But SFP will not work.
> This patch series implement I2C, GPIO, SFP and PHYLINK. The support of SFP
> is dependent on I2C and GPIO. If these patches will be end up merging in the
> same upstream version, it's not a problem to merge them in different trees,
> I think.

That's how I saw it as well.

Applied to for-next, thanks!


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Russell King (Oracle)]

On Mon, Jun 05, 2023 at 12:05:35PM +0200, 'Wolfram Sang' wrote:
> 
> > Yes, other patches will build even without this patch. But SFP will not work.
> > This patch series implement I2C, GPIO, SFP and PHYLINK. The support of SFP
> > is dependent on I2C and GPIO. If these patches will be end up merging in the
> > same upstream version, it's not a problem to merge them in different trees,
> > I think.
> 
> That's how I saw it as well.
> 
> Applied to for-next, thanks!

Be careful... net-next uses patchwork, and I suspect as this is posted
as a series which the subject line states as being destined by the
author for the "net-next" tree, the entire series will end up being
slurped into the net-next tree.

https://www.kernel.org/doc/html/v5.10/networking/netdev-FAQ.html#q-how-do-i-indicate-which-tree-net-vs-net-next-my-patch-should-be-in

This patch is still marked as "new" in patchwork:

https://patchwork.kernel.org/project/netdevbpf/patch/20230605025211.743823-3-jiawenwu@trustnetic.com/

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

['Wolfram Sang']

[-- Attachment #1: Type: text/plain, Size: 351 bytes --]


> Be careful... net-next uses patchwork, and I suspect as this is posted
> as a series which the subject line states as being destined by the
> author for the "net-next" tree, the entire series will end up being
> slurped into the net-next tree.

Thanks for the pointer. Jiawen Wu, would you kindly send a v12 of the
series (without the I2C patch)?


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Andy Shevchenko]

On Mon, Jun 05, 2023 at 02:57:36PM +0200, 'Wolfram Sang' wrote:
> 
> > Be careful... net-next uses patchwork, and I suspect as this is posted
> > as a series which the subject line states as being destined by the
> > author for the "net-next" tree, the entire series will end up being
> > slurped into the net-next tree.
> 
> Thanks for the pointer. Jiawen Wu, would you kindly send a v12 of the
> series (without the I2C patch)?

I'm wondering if it would be easier just mark it in patchwork as applied
elsewhere (don't remember exact variant, but meaning is the same).

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jakub Kicinski]

On Mon, 5 Jun 2023 16:03:23 +0300 Andy Shevchenko wrote:
> I'm wondering if it would be easier just mark it in patchwork as applied
> elsewhere (don't remember exact variant, but meaning is the same).

It would not. PW doesn't support sparse series well and it's just
confusing to everyone. We don't do manual handpicking in netdev.
Reposting the remaining patches is the right thing to do.

RE: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jiawen Wu]

On Monday, June 5, 2023 8:58 PM, Wolfram Sang wrote:
> > Be careful... net-next uses patchwork, and I suspect as this is posted
> > as a series which the subject line states as being destined by the
> > author for the "net-next" tree, the entire series will end up being
> > slurped into the net-next tree.
> 
> Thanks for the pointer. Jiawen Wu, would you kindly send a v12 of the
> series (without the I2C patch)?

Okay, v12 series will be other 8 patches for net-next.
Do I need to send this independent patch to I2C tree?

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

['Wolfram Sang']

[-- Attachment #1: Type: text/plain, Size: 142 bytes --]

> Okay, v12 series will be other 8 patches for net-next.
> Do I need to send this independent patch to I2C tree?

No, it is already applied.


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH net-next v11 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jarkko Nikula]

On 6/5/23 05:52, Jiawen Wu wrote:
> Wangxun 10Gb ethernet chip is connected to Designware I2C, to communicate
> with SFP.
> 
> Introduce the property "wx,i2c-snps-model" to match device data for Wangxun
> in software node case. Since IO resource was mapped on the ethernet driver,
> add a model quirk to get regmap from parent device.
> 
> The exists IP limitations are dealt as workarounds:
> - IP does not support interrupt mode, it works on polling mode.
> - Additionally set FIFO depth address the chip issue.
> 
> Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> ---
>   drivers/i2c/busses/i2c-designware-common.c  |  8 ++
>   drivers/i2c/busses/i2c-designware-core.h    |  4 +
>   drivers/i2c/busses/i2c-designware-master.c  | 89 +++++++++++++++++++--
>   drivers/i2c/busses/i2c-designware-platdrv.c | 15 ++++
>   4 files changed, 111 insertions(+), 5 deletions(-)
> 
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>

[PATCH net-next v11 3/9] net: txgbe: Register fixed rate clock

[Jiawen Wu]

In order for I2C to be able to work in standard mode, register a fixed
rate clock for each I2C device.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/ethernet/wangxun/Kconfig          |  1 +
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 41 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  2 +
 3 files changed, 44 insertions(+)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index c9d88673d306..190d42a203b4 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -40,6 +40,7 @@ config NGBE
 config TXGBE
 	tristate "Wangxun(R) 10GbE PCI Express adapters support"
 	depends on PCI
+	depends on COMMON_CLK
 	select LIBWX
 	help
 	  This driver supports Wangxun(R) 10GbE PCI Express family of
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index be4b5ad74a3c..06506cfb8d06 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -2,6 +2,8 @@
 /* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
 
 #include <linux/gpio/property.h>
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
 #include <linux/i2c.h>
 #include <linux/pci.h>
 
@@ -70,6 +72,32 @@ static int txgbe_swnodes_register(struct txgbe *txgbe)
 	return software_node_register_node_group(nodes->group);
 }
 
+static int txgbe_clock_register(struct txgbe *txgbe)
+{
+	struct pci_dev *pdev = txgbe->wx->pdev;
+	struct clk_lookup *clock;
+	char clk_name[32];
+	struct clk *clk;
+
+	snprintf(clk_name, sizeof(clk_name), "i2c_designware.%d",
+		 (pdev->bus->number << 8) | pdev->devfn);
+
+	clk = clk_register_fixed_rate(NULL, clk_name, NULL, 0, 156250000);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	clock = clkdev_create(clk, NULL, clk_name);
+	if (!clock) {
+		clk_unregister(clk);
+		return -ENOMEM;
+	}
+
+	txgbe->clk = clk;
+	txgbe->clock = clock;
+
+	return 0;
+}
+
 int txgbe_init_phy(struct txgbe *txgbe)
 {
 	int ret;
@@ -80,10 +108,23 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		return ret;
 	}
 
+	ret = txgbe_clock_register(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to register clock: %d\n", ret);
+		goto err_unregister_swnode;
+	}
+
 	return 0;
+
+err_unregister_swnode:
+	software_node_unregister_node_group(txgbe->nodes.group);
+
+	return ret;
 }
 
 void txgbe_remove_phy(struct txgbe *txgbe)
 {
+	clkdev_drop(txgbe->clock);
+	clk_unregister(txgbe->clk);
 	software_node_unregister_node_group(txgbe->nodes.group);
 }
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 9aa399acd9a0..856d0f9d045b 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -147,6 +147,8 @@ struct txgbe_nodes {
 struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
+	struct clk_lookup *clock;
+	struct clk *clk;
 };
 
 #endif /* _TXGBE_TYPE_H_ */
-- 
2.27.0

[PATCH net-next v11 4/9] net: txgbe: Register I2C platform device

[Jiawen Wu]

Register the platform device to use Designware I2C bus master driver.
Use regmap to read/write I2C device region from given base offset.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |  3 +
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 70 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  4 ++
 3 files changed, 77 insertions(+)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index 190d42a203b4..128cc1cb0605 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -41,6 +41,9 @@ config TXGBE
 	tristate "Wangxun(R) 10GbE PCI Express adapters support"
 	depends on PCI
 	depends on COMMON_CLK
+	select REGMAP
+	select I2C
+	select I2C_DESIGNWARE_PLATFORM
 	select LIBWX
 	help
 	  This driver supports Wangxun(R) 10GbE PCI Express family of
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 06506cfb8d06..24a729150e08 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -6,6 +6,8 @@
 #include <linux/clkdev.h>
 #include <linux/i2c.h>
 #include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
 
 #include "../libwx/wx_type.h"
 #include "txgbe_type.h"
@@ -98,6 +100,64 @@ static int txgbe_clock_register(struct txgbe *txgbe)
 	return 0;
 }
 
+static int txgbe_i2c_read(void *context, unsigned int reg, unsigned int *val)
+{
+	struct wx *wx = context;
+
+	*val = rd32(wx, reg + TXGBE_I2C_BASE);
+
+	return 0;
+}
+
+static int txgbe_i2c_write(void *context, unsigned int reg, unsigned int val)
+{
+	struct wx *wx = context;
+
+	wr32(wx, reg + TXGBE_I2C_BASE, val);
+
+	return 0;
+}
+
+static const struct regmap_config i2c_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_read = txgbe_i2c_read,
+	.reg_write = txgbe_i2c_write,
+	.fast_io = true,
+};
+
+static int txgbe_i2c_register(struct txgbe *txgbe)
+{
+	struct platform_device_info info = {};
+	struct platform_device *i2c_dev;
+	struct regmap *i2c_regmap;
+	struct pci_dev *pdev;
+	struct wx *wx;
+
+	wx = txgbe->wx;
+	pdev = wx->pdev;
+	i2c_regmap = devm_regmap_init(&pdev->dev, NULL, wx, &i2c_regmap_config);
+	if (IS_ERR(i2c_regmap)) {
+		wx_err(wx, "failed to init I2C regmap\n");
+		return PTR_ERR(i2c_regmap);
+	}
+
+	info.parent = &pdev->dev;
+	info.fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_I2C]);
+	info.name = "i2c_designware";
+	info.id = (pdev->bus->number << 8) | pdev->devfn;
+
+	info.res = &DEFINE_RES_IRQ(pdev->irq);
+	info.num_res = 1;
+	i2c_dev = platform_device_register_full(&info);
+	if (IS_ERR(i2c_dev))
+		return PTR_ERR(i2c_dev);
+
+	txgbe->i2c_dev = i2c_dev;
+
+	return 0;
+}
+
 int txgbe_init_phy(struct txgbe *txgbe)
 {
 	int ret;
@@ -114,8 +174,17 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		goto err_unregister_swnode;
 	}
 
+	ret = txgbe_i2c_register(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to init i2c interface: %d\n", ret);
+		goto err_unregister_clk;
+	}
+
 	return 0;
 
+err_unregister_clk:
+	clkdev_drop(txgbe->clock);
+	clk_unregister(txgbe->clk);
 err_unregister_swnode:
 	software_node_unregister_node_group(txgbe->nodes.group);
 
@@ -124,6 +193,7 @@ int txgbe_init_phy(struct txgbe *txgbe)
 
 void txgbe_remove_phy(struct txgbe *txgbe)
 {
+	platform_device_unregister(txgbe->i2c_dev);
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
 	software_node_unregister_node_group(txgbe->nodes.group);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 856d0f9d045b..6e471a4d68cc 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -55,6 +55,9 @@
 #define TXGBE_TS_CTL                            0x10300
 #define TXGBE_TS_CTL_EVAL_MD                    BIT(31)
 
+/* I2C registers */
+#define TXGBE_I2C_BASE                          0x14900
+
 /* Part Number String Length */
 #define TXGBE_PBANUM_LENGTH                     32
 
@@ -147,6 +150,7 @@ struct txgbe_nodes {
 struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
+	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
 	struct clk *clk;
 };
-- 
2.27.0

[PATCH net-next v11 5/9] net: txgbe: Add SFP module identify

[Jiawen Wu]

Register SFP platform device to get modules information.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |  3 ++
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 28 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  1 +
 3 files changed, 32 insertions(+)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index 128cc1cb0605..59f3a3f492cf 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -44,6 +44,9 @@ config TXGBE
 	select REGMAP
 	select I2C
 	select I2C_DESIGNWARE_PLATFORM
+	select PHYLINK
+	select HWMON if TXGBE=y
+	select SFP
 	select LIBWX
 	help
 	  This driver supports Wangxun(R) 10GbE PCI Express family of
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 24a729150e08..d95dc131e91b 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -158,6 +158,25 @@ static int txgbe_i2c_register(struct txgbe *txgbe)
 	return 0;
 }
 
+static int txgbe_sfp_register(struct txgbe *txgbe)
+{
+	struct pci_dev *pdev = txgbe->wx->pdev;
+	struct platform_device_info info = {};
+	struct platform_device *sfp_dev;
+
+	info.parent = &pdev->dev;
+	info.fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_SFP]);
+	info.name = "sfp";
+	info.id = (pdev->bus->number << 8) | pdev->devfn;
+	sfp_dev = platform_device_register_full(&info);
+	if (IS_ERR(sfp_dev))
+		return PTR_ERR(sfp_dev);
+
+	txgbe->sfp_dev = sfp_dev;
+
+	return 0;
+}
+
 int txgbe_init_phy(struct txgbe *txgbe)
 {
 	int ret;
@@ -180,8 +199,16 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		goto err_unregister_clk;
 	}
 
+	ret = txgbe_sfp_register(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to register sfp\n");
+		goto err_unregister_i2c;
+	}
+
 	return 0;
 
+err_unregister_i2c:
+	platform_device_unregister(txgbe->i2c_dev);
 err_unregister_clk:
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
@@ -193,6 +220,7 @@ int txgbe_init_phy(struct txgbe *txgbe)
 
 void txgbe_remove_phy(struct txgbe *txgbe)
 {
+	platform_device_unregister(txgbe->sfp_dev);
 	platform_device_unregister(txgbe->i2c_dev);
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 6e471a4d68cc..f420e2569247 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -150,6 +150,7 @@ struct txgbe_nodes {
 struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
+	struct platform_device *sfp_dev;
 	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
 	struct clk *clk;
-- 
2.27.0

[PATCH net-next v11 6/9] net: txgbe: Support GPIO to SFP socket

[Jiawen Wu]

Register GPIO chip and handle GPIO IRQ for SFP socket.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |   2 +
 drivers/net/ethernet/wangxun/libwx/wx_lib.c   |   3 +-
 drivers/net/ethernet/wangxun/libwx/wx_type.h  |   3 +
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   |  20 +-
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 251 ++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  23 ++
 6 files changed, 283 insertions(+), 19 deletions(-)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index 59f3a3f492cf..3744735fa708 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -47,6 +47,8 @@ config TXGBE
 	select PHYLINK
 	select HWMON if TXGBE=y
 	select SFP
+	select GPIOLIB
+	select GPIOLIB_IRQCHIP
 	select LIBWX
 	help
 	  This driver supports Wangxun(R) 10GbE PCI Express family of
diff --git a/drivers/net/ethernet/wangxun/libwx/wx_lib.c b/drivers/net/ethernet/wangxun/libwx/wx_lib.c
index 3dd328d33fcc..2c3f08be8c37 100644
--- a/drivers/net/ethernet/wangxun/libwx/wx_lib.c
+++ b/drivers/net/ethernet/wangxun/libwx/wx_lib.c
@@ -2048,7 +2048,8 @@ void wx_free_irq(struct wx *wx)
 		free_irq(entry->vector, q_vector);
 	}
 
-	free_irq(wx->msix_entries[vector].vector, wx);
+	if (wx->mac.type == wx_mac_em)
+		free_irq(wx->msix_entries[vector].vector, wx);
 }
 EXPORT_SYMBOL(wx_free_irq);
 
diff --git a/drivers/net/ethernet/wangxun/libwx/wx_type.h b/drivers/net/ethernet/wangxun/libwx/wx_type.h
index c61c18a842c4..29dfb561887d 100644
--- a/drivers/net/ethernet/wangxun/libwx/wx_type.h
+++ b/drivers/net/ethernet/wangxun/libwx/wx_type.h
@@ -83,7 +83,9 @@
 #define WX_GPIO_INTMASK              0x14834
 #define WX_GPIO_INTTYPE_LEVEL        0x14838
 #define WX_GPIO_POLARITY             0x1483C
+#define WX_GPIO_INTSTATUS            0x14844
 #define WX_GPIO_EOI                  0x1484C
+#define WX_GPIO_EXT                  0x14850
 
 /*********************** Transmit DMA registers **************************/
 /* transmit global control */
@@ -847,6 +849,7 @@ struct wx {
 	bool wol_enabled;
 	bool ncsi_enabled;
 	bool gpio_ctrl;
+	raw_spinlock_t gpio_lock;
 
 	/* Tx fast path data */
 	int num_tx_queues;
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
index 2335fa863fa5..e6eee4446ea6 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
@@ -82,6 +82,8 @@ static int txgbe_enumerate_functions(struct wx *wx)
  **/
 static void txgbe_irq_enable(struct wx *wx, bool queues)
 {
+	wr32(wx, WX_PX_MISC_IEN, TXGBE_PX_MISC_IEN_MASK);
+
 	/* unmask interrupt */
 	wx_intr_enable(wx, TXGBE_INTR_MISC(wx));
 	if (queues)
@@ -129,17 +131,6 @@ static irqreturn_t txgbe_intr(int __always_unused irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static irqreturn_t txgbe_msix_other(int __always_unused irq, void *data)
-{
-	struct wx *wx = data;
-
-	/* re-enable the original interrupt state */
-	if (netif_running(wx->netdev))
-		txgbe_irq_enable(wx, false);
-
-	return IRQ_HANDLED;
-}
-
 /**
  * txgbe_request_msix_irqs - Initialize MSI-X interrupts
  * @wx: board private structure
@@ -171,13 +162,6 @@ static int txgbe_request_msix_irqs(struct wx *wx)
 		}
 	}
 
-	err = request_irq(wx->msix_entries[vector].vector,
-			  txgbe_msix_other, 0, netdev->name, wx);
-	if (err) {
-		wx_err(wx, "request_irq for msix_other failed: %d\n", err);
-		goto free_queue_irqs;
-	}
-
 	return 0;
 
 free_queue_irqs:
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index d95dc131e91b..97c018a10c39 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -1,6 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0
 /* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
 
+#include <linux/gpio/machine.h>
+#include <linux/gpio/driver.h>
 #include <linux/gpio/property.h>
 #include <linux/clk-provider.h>
 #include <linux/clkdev.h>
@@ -10,6 +12,7 @@
 #include <linux/regmap.h>
 
 #include "../libwx/wx_type.h"
+#include "../libwx/wx_hw.h"
 #include "txgbe_type.h"
 #include "txgbe_phy.h"
 
@@ -74,6 +77,248 @@ static int txgbe_swnodes_register(struct txgbe *txgbe)
 	return software_node_register_node_group(nodes->group);
 }
 
+static int txgbe_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct wx *wx = gpiochip_get_data(chip);
+	int val;
+
+	val = rd32m(wx, WX_GPIO_EXT, BIT(offset));
+
+	return !!(val & BIT(offset));
+}
+
+static int txgbe_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	struct wx *wx = gpiochip_get_data(chip);
+	u32 val;
+
+	val = rd32(wx, WX_GPIO_DDR);
+	if (BIT(offset) & val)
+		return GPIO_LINE_DIRECTION_OUT;
+
+	return GPIO_LINE_DIRECTION_IN;
+}
+
+static int txgbe_gpio_direction_in(struct gpio_chip *chip, unsigned int offset)
+{
+	struct wx *wx = gpiochip_get_data(chip);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&wx->gpio_lock, flags);
+	wr32m(wx, WX_GPIO_DDR, BIT(offset), 0);
+	raw_spin_unlock_irqrestore(&wx->gpio_lock, flags);
+
+	return 0;
+}
+
+static int txgbe_gpio_direction_out(struct gpio_chip *chip, unsigned int offset,
+				    int val)
+{
+	struct wx *wx = gpiochip_get_data(chip);
+	unsigned long flags;
+	u32 set;
+
+	set = val ? BIT(offset) : 0;
+
+	raw_spin_lock_irqsave(&wx->gpio_lock, flags);
+	wr32m(wx, WX_GPIO_DR, BIT(offset), set);
+	wr32m(wx, WX_GPIO_DDR, BIT(offset), BIT(offset));
+	raw_spin_unlock_irqrestore(&wx->gpio_lock, flags);
+
+	return 0;
+}
+
+static void txgbe_gpio_irq_ack(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	struct wx *wx = gpiochip_get_data(gc);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&wx->gpio_lock, flags);
+	wr32(wx, WX_GPIO_EOI, BIT(hwirq));
+	raw_spin_unlock_irqrestore(&wx->gpio_lock, flags);
+}
+
+static void txgbe_gpio_irq_mask(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	struct wx *wx = gpiochip_get_data(gc);
+	unsigned long flags;
+
+	gpiochip_disable_irq(gc, hwirq);
+
+	raw_spin_lock_irqsave(&wx->gpio_lock, flags);
+	wr32m(wx, WX_GPIO_INTMASK, BIT(hwirq), BIT(hwirq));
+	raw_spin_unlock_irqrestore(&wx->gpio_lock, flags);
+}
+
+static void txgbe_gpio_irq_unmask(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	struct wx *wx = gpiochip_get_data(gc);
+	unsigned long flags;
+
+	gpiochip_enable_irq(gc, hwirq);
+
+	raw_spin_lock_irqsave(&wx->gpio_lock, flags);
+	wr32m(wx, WX_GPIO_INTMASK, BIT(hwirq), 0);
+	raw_spin_unlock_irqrestore(&wx->gpio_lock, flags);
+}
+
+static void txgbe_toggle_trigger(struct gpio_chip *gc, unsigned int offset)
+{
+	struct wx *wx = gpiochip_get_data(gc);
+	u32 pol, val;
+
+	pol = rd32(wx, WX_GPIO_POLARITY);
+	val = rd32(wx, WX_GPIO_EXT);
+
+	if (val & BIT(offset))
+		pol &= ~BIT(offset);
+	else
+		pol |= BIT(offset);
+
+	wr32(wx, WX_GPIO_POLARITY, pol);
+}
+
+static int txgbe_gpio_set_type(struct irq_data *d, unsigned int type)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	struct wx *wx = gpiochip_get_data(gc);
+	u32 level, polarity, mask;
+	unsigned long flags;
+
+	mask = BIT(hwirq);
+
+	if (type & IRQ_TYPE_LEVEL_MASK) {
+		level = 0;
+		irq_set_handler_locked(d, handle_level_irq);
+	} else {
+		level = mask;
+		irq_set_handler_locked(d, handle_edge_irq);
+	}
+
+	if (type == IRQ_TYPE_EDGE_RISING || type == IRQ_TYPE_LEVEL_HIGH)
+		polarity = mask;
+	else
+		polarity = 0;
+
+	raw_spin_lock_irqsave(&wx->gpio_lock, flags);
+
+	wr32m(wx, WX_GPIO_INTEN, mask, mask);
+	wr32m(wx, WX_GPIO_INTTYPE_LEVEL, mask, level);
+	if (type == IRQ_TYPE_EDGE_BOTH)
+		txgbe_toggle_trigger(gc, hwirq);
+	else
+		wr32m(wx, WX_GPIO_POLARITY, mask, polarity);
+
+	raw_spin_unlock_irqrestore(&wx->gpio_lock, flags);
+
+	return 0;
+}
+
+static const struct irq_chip txgbe_gpio_irq_chip = {
+	.name = "txgbe_gpio_irq",
+	.irq_ack = txgbe_gpio_irq_ack,
+	.irq_mask = txgbe_gpio_irq_mask,
+	.irq_unmask = txgbe_gpio_irq_unmask,
+	.irq_set_type = txgbe_gpio_set_type,
+	.flags = IRQCHIP_IMMUTABLE,
+	GPIOCHIP_IRQ_RESOURCE_HELPERS,
+};
+
+static void txgbe_irq_handler(struct irq_desc *desc)
+{
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	struct wx *wx = irq_desc_get_handler_data(desc);
+	struct txgbe *txgbe = wx->priv;
+	irq_hw_number_t hwirq;
+	unsigned long gpioirq;
+	struct gpio_chip *gc;
+	unsigned long flags;
+
+	chained_irq_enter(chip, desc);
+
+	gpioirq = rd32(wx, WX_GPIO_INTSTATUS);
+
+	gc = txgbe->gpio;
+	for_each_set_bit(hwirq, &gpioirq, gc->ngpio) {
+		int gpio = irq_find_mapping(gc->irq.domain, hwirq);
+		u32 irq_type = irq_get_trigger_type(gpio);
+
+		generic_handle_domain_irq(gc->irq.domain, hwirq);
+
+		if ((irq_type & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) {
+			raw_spin_lock_irqsave(&wx->gpio_lock, flags);
+			txgbe_toggle_trigger(gc, hwirq);
+			raw_spin_unlock_irqrestore(&wx->gpio_lock, flags);
+		}
+	}
+
+	chained_irq_exit(chip, desc);
+
+	/* unmask interrupt */
+	wx_intr_enable(wx, TXGBE_INTR_MISC(wx));
+}
+
+static int txgbe_gpio_init(struct txgbe *txgbe)
+{
+	struct gpio_irq_chip *girq;
+	struct gpio_chip *gc;
+	struct device *dev;
+	struct wx *wx;
+	int ret;
+
+	wx = txgbe->wx;
+	dev = &wx->pdev->dev;
+
+	raw_spin_lock_init(&wx->gpio_lock);
+
+	gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc)
+		return -ENOMEM;
+
+	gc->label = devm_kasprintf(dev, GFP_KERNEL, "txgbe_gpio-%x",
+				   (wx->pdev->bus->number << 8) | wx->pdev->devfn);
+	if (!gc->label)
+		return -ENOMEM;
+
+	gc->base = -1;
+	gc->ngpio = 6;
+	gc->owner = THIS_MODULE;
+	gc->parent = dev;
+	gc->fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_GPIO]);
+	gc->get = txgbe_gpio_get;
+	gc->get_direction = txgbe_gpio_get_direction;
+	gc->direction_input = txgbe_gpio_direction_in;
+	gc->direction_output = txgbe_gpio_direction_out;
+
+	girq = &gc->irq;
+	gpio_irq_chip_set_chip(girq, &txgbe_gpio_irq_chip);
+	girq->parent_handler = txgbe_irq_handler;
+	girq->parent_handler_data = wx;
+	girq->num_parents = 1;
+	girq->parents = devm_kcalloc(dev, girq->num_parents,
+				     sizeof(*girq->parents), GFP_KERNEL);
+	if (!girq->parents)
+		return -ENOMEM;
+	girq->parents[0] = wx->msix_entries[wx->num_q_vectors].vector;
+	girq->default_type = IRQ_TYPE_NONE;
+	girq->handler = handle_bad_irq;
+
+	ret = devm_gpiochip_add_data(dev, gc, wx);
+	if (ret)
+		return ret;
+
+	txgbe->gpio = gc;
+
+	return 0;
+}
+
 static int txgbe_clock_register(struct txgbe *txgbe)
 {
 	struct pci_dev *pdev = txgbe->wx->pdev;
@@ -187,6 +432,12 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		return ret;
 	}
 
+	ret = txgbe_gpio_init(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to init gpio\n");
+		goto err_unregister_swnode;
+	}
+
 	ret = txgbe_clock_register(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to register clock: %d\n", ret);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index f420e2569247..60ecc5a90203 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -55,6 +55,28 @@
 #define TXGBE_TS_CTL                            0x10300
 #define TXGBE_TS_CTL_EVAL_MD                    BIT(31)
 
+/* GPIO register bit */
+#define TXGBE_GPIOBIT_0                         BIT(0) /* I:tx fault */
+#define TXGBE_GPIOBIT_1                         BIT(1) /* O:tx disabled */
+#define TXGBE_GPIOBIT_2                         BIT(2) /* I:sfp module absent */
+#define TXGBE_GPIOBIT_3                         BIT(3) /* I:rx signal lost */
+#define TXGBE_GPIOBIT_4                         BIT(4) /* O:rate select, 1G(0) 10G(1) */
+#define TXGBE_GPIOBIT_5                         BIT(5) /* O:rate select, 1G(0) 10G(1) */
+
+/* Extended Interrupt Enable Set */
+#define TXGBE_PX_MISC_ETH_LKDN                  BIT(8)
+#define TXGBE_PX_MISC_DEV_RST                   BIT(10)
+#define TXGBE_PX_MISC_ETH_EVENT                 BIT(17)
+#define TXGBE_PX_MISC_ETH_LK                    BIT(18)
+#define TXGBE_PX_MISC_ETH_AN                    BIT(19)
+#define TXGBE_PX_MISC_INT_ERR                   BIT(20)
+#define TXGBE_PX_MISC_GPIO                      BIT(26)
+#define TXGBE_PX_MISC_IEN_MASK                            \
+	(TXGBE_PX_MISC_ETH_LKDN | TXGBE_PX_MISC_DEV_RST | \
+	 TXGBE_PX_MISC_ETH_EVENT | TXGBE_PX_MISC_ETH_LK | \
+	 TXGBE_PX_MISC_ETH_AN | TXGBE_PX_MISC_INT_ERR |   \
+	 TXGBE_PX_MISC_GPIO)
+
 /* I2C registers */
 #define TXGBE_I2C_BASE                          0x14900
 
@@ -154,6 +176,7 @@ struct txgbe {
 	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
 	struct clk *clk;
+	struct gpio_chip *gpio;
 };
 
 #endif /* _TXGBE_TYPE_H_ */
-- 
2.27.0

[PATCH net-next v11 7/9] net: pcs: Add 10GBASE-R mode for Synopsys Designware XPCS

[Jiawen Wu]

Add basic support for XPCS using 10GBASE-R interface. This mode will
be extended to use interrupt, so set pcs.poll false. And avoid soft
reset so that the device using this mode is in the default configuration.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/pcs/pcs-xpcs.c   | 30 ++++++++++++++++++++++++++++++
 include/linux/pcs/pcs-xpcs.h |  1 +
 2 files changed, 31 insertions(+)

diff --git a/drivers/net/pcs/pcs-xpcs.c b/drivers/net/pcs/pcs-xpcs.c
index 1ba214429e01..b2ef5fdce3b0 100644
--- a/drivers/net/pcs/pcs-xpcs.c
+++ b/drivers/net/pcs/pcs-xpcs.c
@@ -64,6 +64,16 @@ static const int xpcs_xlgmii_features[] = {
 	__ETHTOOL_LINK_MODE_MASK_NBITS,
 };
 
+static const int xpcs_10gbaser_features[] = {
+	ETHTOOL_LINK_MODE_Pause_BIT,
+	ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+	ETHTOOL_LINK_MODE_10000baseSR_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseLR_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseLRM_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseER_Full_BIT,
+	__ETHTOOL_LINK_MODE_MASK_NBITS,
+};
+
 static const int xpcs_sgmii_features[] = {
 	ETHTOOL_LINK_MODE_Pause_BIT,
 	ETHTOOL_LINK_MODE_Asym_Pause_BIT,
@@ -106,6 +116,10 @@ static const phy_interface_t xpcs_xlgmii_interfaces[] = {
 	PHY_INTERFACE_MODE_XLGMII,
 };
 
+static const phy_interface_t xpcs_10gbaser_interfaces[] = {
+	PHY_INTERFACE_MODE_10GBASER,
+};
+
 static const phy_interface_t xpcs_sgmii_interfaces[] = {
 	PHY_INTERFACE_MODE_SGMII,
 };
@@ -123,6 +137,7 @@ enum {
 	DW_XPCS_USXGMII,
 	DW_XPCS_10GKR,
 	DW_XPCS_XLGMII,
+	DW_XPCS_10GBASER,
 	DW_XPCS_SGMII,
 	DW_XPCS_1000BASEX,
 	DW_XPCS_2500BASEX,
@@ -246,6 +261,7 @@ static int xpcs_soft_reset(struct dw_xpcs *xpcs,
 
 	switch (compat->an_mode) {
 	case DW_AN_C73:
+	case DW_10GBASER:
 		dev = MDIO_MMD_PCS;
 		break;
 	case DW_AN_C37_SGMII:
@@ -802,6 +818,8 @@ int xpcs_do_config(struct dw_xpcs *xpcs, phy_interface_t interface,
 		return -ENODEV;
 
 	switch (compat->an_mode) {
+	case DW_10GBASER:
+		break;
 	case DW_AN_C73:
 		if (test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, advertising)) {
 			ret = xpcs_config_aneg_c73(xpcs, compat);
@@ -998,6 +1016,9 @@ static void xpcs_get_state(struct phylink_pcs *pcs,
 		return;
 
 	switch (compat->an_mode) {
+	case DW_10GBASER:
+		phylink_mii_c45_pcs_get_state(xpcs->mdiodev, state);
+		break;
 	case DW_AN_C73:
 		ret = xpcs_get_state_c73(xpcs, state, compat);
 		if (ret) {
@@ -1153,6 +1174,12 @@ static const struct xpcs_compat synopsys_xpcs_compat[DW_XPCS_INTERFACE_MAX] = {
 		.num_interfaces = ARRAY_SIZE(xpcs_xlgmii_interfaces),
 		.an_mode = DW_AN_C73,
 	},
+	[DW_XPCS_10GBASER] = {
+		.supported = xpcs_10gbaser_features,
+		.interface = xpcs_10gbaser_interfaces,
+		.num_interfaces = ARRAY_SIZE(xpcs_10gbaser_interfaces),
+		.an_mode = DW_10GBASER,
+	},
 	[DW_XPCS_SGMII] = {
 		.supported = xpcs_sgmii_features,
 		.interface = xpcs_sgmii_interfaces,
@@ -1256,6 +1283,9 @@ struct dw_xpcs *xpcs_create(struct mdio_device *mdiodev,
 		}
 
 		xpcs->pcs.ops = &xpcs_phylink_ops;
+		if (compat->an_mode == DW_10GBASER)
+			return xpcs;
+
 		xpcs->pcs.poll = true;
 
 		ret = xpcs_soft_reset(xpcs, compat);
diff --git a/include/linux/pcs/pcs-xpcs.h b/include/linux/pcs/pcs-xpcs.h
index a99972a6d046..daea67b6e3c0 100644
--- a/include/linux/pcs/pcs-xpcs.h
+++ b/include/linux/pcs/pcs-xpcs.h
@@ -18,6 +18,7 @@
 #define DW_AN_C37_SGMII			2
 #define DW_2500BASEX			3
 #define DW_AN_C37_1000BASEX		4
+#define DW_10GBASER			5
 
 struct xpcs_id;
 
-- 
2.27.0

[PATCH net-next v11 8/9] net: txgbe: Implement phylink pcs

[Jiawen Wu]

Register MDIO bus for PCS layer to use Synopsys designware XPCS, support
10GBASE-R interface to the controller.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/ethernet/wangxun/Kconfig          |  1 +
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 89 ++++++++++++++++++-
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  5 ++
 3 files changed, 93 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index 3744735fa708..39596cd13539 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -49,6 +49,7 @@ config TXGBE
 	select SFP
 	select GPIOLIB
 	select GPIOLIB_IRQCHIP
+	select PCS_XPCS
 	select LIBWX
 	help
 	  This driver supports Wangxun(R) 10GbE PCI Express family of
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 97c018a10c39..58e12c35627a 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -10,6 +10,7 @@
 #include <linux/pci.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
+#include <linux/pcs/pcs-xpcs.h>
 
 #include "../libwx/wx_type.h"
 #include "../libwx/wx_hw.h"
@@ -77,6 +78,81 @@ static int txgbe_swnodes_register(struct txgbe *txgbe)
 	return software_node_register_node_group(nodes->group);
 }
 
+static int txgbe_pcs_read(struct mii_bus *bus, int addr, int devnum, int regnum)
+{
+	struct wx *wx  = bus->priv;
+	u32 offset, val;
+
+	if (addr)
+		return -EOPNOTSUPP;
+
+	offset = devnum << 16 | regnum;
+
+	/* Set the LAN port indicator to IDA_ADDR */
+	wr32(wx, TXGBE_XPCS_IDA_ADDR, offset);
+
+	/* Read the data from IDA_DATA register */
+	val = rd32(wx, TXGBE_XPCS_IDA_DATA);
+
+	return (u16)val;
+}
+
+static int txgbe_pcs_write(struct mii_bus *bus, int addr, int devnum, int regnum, u16 val)
+{
+	struct wx *wx = bus->priv;
+	u32 offset;
+
+	if (addr)
+		return -EOPNOTSUPP;
+
+	offset = devnum << 16 | regnum;
+
+	/* Set the LAN port indicator to IDA_ADDR */
+	wr32(wx, TXGBE_XPCS_IDA_ADDR, offset);
+
+	/* Write the data to IDA_DATA register */
+	wr32(wx, TXGBE_XPCS_IDA_DATA, val);
+
+	return 0;
+}
+
+static int txgbe_mdio_pcs_init(struct txgbe *txgbe)
+{
+	struct mii_bus *mii_bus;
+	struct dw_xpcs *xpcs;
+	struct pci_dev *pdev;
+	struct wx *wx;
+	int ret = 0;
+
+	wx = txgbe->wx;
+	pdev = wx->pdev;
+
+	mii_bus = devm_mdiobus_alloc(&pdev->dev);
+	if (!mii_bus)
+		return -ENOMEM;
+
+	mii_bus->name = "txgbe_pcs_mdio_bus";
+	mii_bus->read_c45 = &txgbe_pcs_read;
+	mii_bus->write_c45 = &txgbe_pcs_write;
+	mii_bus->parent = &pdev->dev;
+	mii_bus->phy_mask = ~0;
+	mii_bus->priv = wx;
+	snprintf(mii_bus->id, MII_BUS_ID_SIZE, "txgbe_pcs-%x",
+		 (pdev->bus->number << 8) | pdev->devfn);
+
+	ret = devm_mdiobus_register(&pdev->dev, mii_bus);
+	if (ret)
+		return ret;
+
+	xpcs = xpcs_create_mdiodev(mii_bus, 0, PHY_INTERFACE_MODE_10GBASER);
+	if (IS_ERR(xpcs))
+		return PTR_ERR(xpcs);
+
+	txgbe->xpcs = xpcs;
+
+	return 0;
+}
+
 static int txgbe_gpio_get(struct gpio_chip *chip, unsigned int offset)
 {
 	struct wx *wx = gpiochip_get_data(chip);
@@ -432,16 +508,22 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		return ret;
 	}
 
+	ret = txgbe_mdio_pcs_init(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to init mdio pcs: %d\n", ret);
+		goto err_unregister_swnode;
+	}
+
 	ret = txgbe_gpio_init(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to init gpio\n");
-		goto err_unregister_swnode;
+		goto err_destroy_xpcs;
 	}
 
 	ret = txgbe_clock_register(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to register clock: %d\n", ret);
-		goto err_unregister_swnode;
+		goto err_destroy_xpcs;
 	}
 
 	ret = txgbe_i2c_register(txgbe);
@@ -463,6 +545,8 @@ int txgbe_init_phy(struct txgbe *txgbe)
 err_unregister_clk:
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
+err_destroy_xpcs:
+	xpcs_destroy(txgbe->xpcs);
 err_unregister_swnode:
 	software_node_unregister_node_group(txgbe->nodes.group);
 
@@ -475,5 +559,6 @@ void txgbe_remove_phy(struct txgbe *txgbe)
 	platform_device_unregister(txgbe->i2c_dev);
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
+	xpcs_destroy(txgbe->xpcs);
 	software_node_unregister_node_group(txgbe->nodes.group);
 }
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 60ecc5a90203..76470582ba1e 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -80,6 +80,10 @@
 /* I2C registers */
 #define TXGBE_I2C_BASE                          0x14900
 
+/************************************** ETH PHY ******************************/
+#define TXGBE_XPCS_IDA_ADDR                     0x13000
+#define TXGBE_XPCS_IDA_DATA                     0x13004
+
 /* Part Number String Length */
 #define TXGBE_PBANUM_LENGTH                     32
 
@@ -172,6 +176,7 @@ struct txgbe_nodes {
 struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
+	struct dw_xpcs *xpcs;
 	struct platform_device *sfp_dev;
 	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
-- 
2.27.0

[PATCH net-next v11 9/9] net: txgbe: Support phylink MAC layer

[Jiawen Wu]

Add phylink support to Wangxun 10Gb Ethernet controller for the 10GBASE-R
interface.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 .../ethernet/wangxun/txgbe/txgbe_ethtool.c    |  28 +++++
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   |  23 ++--
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 113 +++++++++++++++++-
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |   5 +
 4 files changed, 154 insertions(+), 15 deletions(-)

diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
index d914e9a05404..859da112586a 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
@@ -6,11 +6,39 @@
 #include <linux/netdevice.h>
 
 #include "../libwx/wx_ethtool.h"
+#include "../libwx/wx_type.h"
+#include "txgbe_type.h"
 #include "txgbe_ethtool.h"
 
+static int txgbe_nway_reset(struct net_device *netdev)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_nway_reset(txgbe->phylink);
+}
+
+static int txgbe_get_link_ksettings(struct net_device *netdev,
+				    struct ethtool_link_ksettings *cmd)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_ksettings_get(txgbe->phylink, cmd);
+}
+
+static int txgbe_set_link_ksettings(struct net_device *netdev,
+				    const struct ethtool_link_ksettings *cmd)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_ksettings_set(txgbe->phylink, cmd);
+}
+
 static const struct ethtool_ops txgbe_ethtool_ops = {
 	.get_drvinfo		= wx_get_drvinfo,
+	.nway_reset		= txgbe_nway_reset,
 	.get_link		= ethtool_op_get_link,
+	.get_link_ksettings	= txgbe_get_link_ksettings,
+	.set_link_ksettings	= txgbe_set_link_ksettings,
 };
 
 void txgbe_set_ethtool_ops(struct net_device *netdev)
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
index e6eee4446ea6..6caf0b0f202b 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
@@ -7,6 +7,7 @@
 #include <linux/netdevice.h>
 #include <linux/string.h>
 #include <linux/etherdevice.h>
+#include <linux/phylink.h>
 #include <net/ip.h>
 #include <linux/if_vlan.h>
 
@@ -204,7 +205,8 @@ static int txgbe_request_irq(struct wx *wx)
 
 static void txgbe_up_complete(struct wx *wx)
 {
-	u32 reg;
+	struct net_device *netdev = wx->netdev;
+	struct txgbe *txgbe;
 
 	wx_control_hw(wx, true);
 	wx_configure_vectors(wx);
@@ -213,24 +215,17 @@ static void txgbe_up_complete(struct wx *wx)
 	smp_mb__before_atomic();
 	wx_napi_enable_all(wx);
 
+	txgbe = netdev_to_txgbe(netdev);
+	phylink_start(txgbe->phylink);
+
 	/* clear any pending interrupts, may auto mask */
 	rd32(wx, WX_PX_IC(0));
 	rd32(wx, WX_PX_IC(1));
 	rd32(wx, WX_PX_MISC_IC);
 	txgbe_irq_enable(wx, true);
 
-	/* Configure MAC Rx and Tx when link is up */
-	reg = rd32(wx, WX_MAC_RX_CFG);
-	wr32(wx, WX_MAC_RX_CFG, reg);
-	wr32(wx, WX_MAC_PKT_FLT, WX_MAC_PKT_FLT_PR);
-	reg = rd32(wx, WX_MAC_WDG_TIMEOUT);
-	wr32(wx, WX_MAC_WDG_TIMEOUT, reg);
-	reg = rd32(wx, WX_MAC_TX_CFG);
-	wr32(wx, WX_MAC_TX_CFG, (reg & ~WX_MAC_TX_CFG_SPEED_MASK) | WX_MAC_TX_CFG_SPEED_10G);
-
 	/* enable transmits */
-	netif_tx_start_all_queues(wx->netdev);
-	netif_carrier_on(wx->netdev);
+	netif_tx_start_all_queues(netdev);
 }
 
 static void txgbe_reset(struct wx *wx)
@@ -265,7 +260,6 @@ static void txgbe_disable_device(struct wx *wx)
 		wx_disable_rx_queue(wx, wx->rx_ring[i]);
 
 	netif_tx_stop_all_queues(netdev);
-	netif_carrier_off(netdev);
 	netif_tx_disable(netdev);
 
 	wx_irq_disable(wx);
@@ -296,8 +290,11 @@ static void txgbe_disable_device(struct wx *wx)
 
 static void txgbe_down(struct wx *wx)
 {
+	struct txgbe *txgbe = netdev_to_txgbe(wx->netdev);
+
 	txgbe_disable_device(wx);
 	txgbe_reset(wx);
+	phylink_stop(txgbe->phylink);
 
 	wx_clean_all_tx_rings(wx);
 	wx_clean_all_rx_rings(wx);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 58e12c35627a..8779645a54be 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -11,8 +11,10 @@
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/pcs/pcs-xpcs.h>
+#include <linux/phylink.h>
 
 #include "../libwx/wx_type.h"
+#include "../libwx/wx_lib.h"
 #include "../libwx/wx_hw.h"
 #include "txgbe_type.h"
 #include "txgbe_phy.h"
@@ -153,6 +155,95 @@ static int txgbe_mdio_pcs_init(struct txgbe *txgbe)
 	return 0;
 }
 
+static struct phylink_pcs *txgbe_phylink_mac_select(struct phylink_config *config,
+						    phy_interface_t interface)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(to_net_dev(config->dev));
+
+	return &txgbe->xpcs->pcs;
+}
+
+static void txgbe_mac_config(struct phylink_config *config, unsigned int mode,
+			     const struct phylink_link_state *state)
+{
+}
+
+static void txgbe_mac_link_down(struct phylink_config *config,
+				unsigned int mode, phy_interface_t interface)
+{
+	struct wx *wx = netdev_priv(to_net_dev(config->dev));
+
+	wr32m(wx, WX_MAC_TX_CFG, WX_MAC_TX_CFG_TE, 0);
+}
+
+static void txgbe_mac_link_up(struct phylink_config *config,
+			      struct phy_device *phy,
+			      unsigned int mode, phy_interface_t interface,
+			      int speed, int duplex,
+			      bool tx_pause, bool rx_pause)
+{
+	struct wx *wx = netdev_priv(to_net_dev(config->dev));
+	u32 txcfg, wdg;
+
+	txcfg = rd32(wx, WX_MAC_TX_CFG);
+	txcfg &= ~WX_MAC_TX_CFG_SPEED_MASK;
+
+	switch (speed) {
+	case SPEED_10000:
+		txcfg |= WX_MAC_TX_CFG_SPEED_10G;
+		break;
+	case SPEED_1000:
+	case SPEED_100:
+	case SPEED_10:
+		txcfg |= WX_MAC_TX_CFG_SPEED_1G;
+		break;
+	default:
+		break;
+	}
+
+	wr32(wx, WX_MAC_TX_CFG, txcfg | WX_MAC_TX_CFG_TE);
+
+	/* Re configure MAC Rx */
+	wr32m(wx, WX_MAC_RX_CFG, WX_MAC_RX_CFG_RE, WX_MAC_RX_CFG_RE);
+	wr32(wx, WX_MAC_PKT_FLT, WX_MAC_PKT_FLT_PR);
+	wdg = rd32(wx, WX_MAC_WDG_TIMEOUT);
+	wr32(wx, WX_MAC_WDG_TIMEOUT, wdg);
+}
+
+static const struct phylink_mac_ops txgbe_mac_ops = {
+	.mac_select_pcs = txgbe_phylink_mac_select,
+	.mac_config = txgbe_mac_config,
+	.mac_link_down = txgbe_mac_link_down,
+	.mac_link_up = txgbe_mac_link_up,
+};
+
+static int txgbe_phylink_init(struct txgbe *txgbe)
+{
+	struct phylink_config *config;
+	struct fwnode_handle *fwnode;
+	struct wx *wx = txgbe->wx;
+	phy_interface_t phy_mode;
+	struct phylink *phylink;
+
+	config = devm_kzalloc(&wx->pdev->dev, sizeof(*config), GFP_KERNEL);
+	if (!config)
+		return -ENOMEM;
+
+	config->dev = &wx->netdev->dev;
+	config->type = PHYLINK_NETDEV;
+	config->mac_capabilities = MAC_10000FD | MAC_1000FD | MAC_SYM_PAUSE | MAC_ASYM_PAUSE;
+	phy_mode = PHY_INTERFACE_MODE_10GBASER;
+	__set_bit(PHY_INTERFACE_MODE_10GBASER, config->supported_interfaces);
+	fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_PHYLINK]);
+	phylink = phylink_create(config, fwnode, phy_mode, &txgbe_mac_ops);
+	if (IS_ERR(phylink))
+		return PTR_ERR(phylink);
+
+	txgbe->phylink = phylink;
+
+	return 0;
+}
+
 static int txgbe_gpio_get(struct gpio_chip *chip, unsigned int offset)
 {
 	struct wx *wx = gpiochip_get_data(chip);
@@ -316,6 +407,9 @@ static void txgbe_irq_handler(struct irq_desc *desc)
 	unsigned long gpioirq;
 	struct gpio_chip *gc;
 	unsigned long flags;
+	u32 eicr;
+
+	eicr = wx_misc_isb(wx, WX_ISB_MISC);
 
 	chained_irq_enter(chip, desc);
 
@@ -337,6 +431,12 @@ static void txgbe_irq_handler(struct irq_desc *desc)
 
 	chained_irq_exit(chip, desc);
 
+	if (eicr & (TXGBE_PX_MISC_ETH_LK | TXGBE_PX_MISC_ETH_LKDN)) {
+		u32 reg = rd32(wx, TXGBE_CFG_PORT_ST);
+
+		phylink_mac_change(txgbe->phylink, !!(reg & TXGBE_CFG_PORT_ST_LINK_UP));
+	}
+
 	/* unmask interrupt */
 	wx_intr_enable(wx, TXGBE_INTR_MISC(wx));
 }
@@ -514,16 +614,22 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		goto err_unregister_swnode;
 	}
 
+	ret = txgbe_phylink_init(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to init phylink\n");
+		goto err_destroy_xpcs;
+	}
+
 	ret = txgbe_gpio_init(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to init gpio\n");
-		goto err_destroy_xpcs;
+		goto err_destroy_phylink;
 	}
 
 	ret = txgbe_clock_register(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to register clock: %d\n", ret);
-		goto err_destroy_xpcs;
+		goto err_destroy_phylink;
 	}
 
 	ret = txgbe_i2c_register(txgbe);
@@ -545,6 +651,8 @@ int txgbe_init_phy(struct txgbe *txgbe)
 err_unregister_clk:
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
+err_destroy_phylink:
+	phylink_destroy(txgbe->phylink);
 err_destroy_xpcs:
 	xpcs_destroy(txgbe->xpcs);
 err_unregister_swnode:
@@ -559,6 +667,7 @@ void txgbe_remove_phy(struct txgbe *txgbe)
 	platform_device_unregister(txgbe->i2c_dev);
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
+	phylink_destroy(txgbe->phylink);
 	xpcs_destroy(txgbe->xpcs);
 	software_node_unregister_node_group(txgbe->nodes.group);
 }
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 76470582ba1e..51199c355f95 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -77,6 +77,10 @@
 	 TXGBE_PX_MISC_ETH_AN | TXGBE_PX_MISC_INT_ERR |   \
 	 TXGBE_PX_MISC_GPIO)
 
+/* Port cfg registers */
+#define TXGBE_CFG_PORT_ST                       0x14404
+#define TXGBE_CFG_PORT_ST_LINK_UP               BIT(0)
+
 /* I2C registers */
 #define TXGBE_I2C_BASE                          0x14900
 
@@ -177,6 +181,7 @@ struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
 	struct dw_xpcs *xpcs;
+	struct phylink *phylink;
 	struct platform_device *sfp_dev;
 	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
-- 
2.27.0