* [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
@ 2023-07-17 16:51 ` Marco Felsch
0 siblings, 0 replies; 39+ messages in thread
From: Marco Felsch @ 2023-07-17 16:51 UTC (permalink / raw)
To: robh+dt, krzysztof.kozlowski+dt, conor+dt, shawnguo, kernel,
festevam, linux-imx, laurent.pinchart, dan.scally
Cc: devicetree, linux-kernel, linux-arm-kernel
Add support for the Debix SOM A + SOM A I/O board. The commit enables
only the basic features like:
- 2x UART
- 2x Network
- eMMC/µSD
- CAN
- QSPI
- USB Host / Device
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
Required patchsets:
- usb: https://lore.kernel.org/all/20230623142228.4069084-1-m.felsch@pengutronix.de/
- net: https://lore.kernel.org/all/20230717164307.2868264-1-m.felsch@pengutronix.de/
Changelog:
v2:
- drop to generic polyhex,imx8mp-debix binding
- net/phy: replace deprecated snps,reset-* and phy-reset-* bindings with
new phy-node based ones
- net/phy: fix phy properties and reset timings
- net/phy: add fec phy-supply handling
- net/phy: add eqos phy-supply handling
- net/phy: fix baseboard-vdd3v3 timings to fulfill net-phy-timings
- Fix spelling
- Drop superfluous blank lines
- pmic: make use of IRQ_TYPE_LEVEL_LOW
- pmic: add whitespace between buck node name and '{'
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../freescale/imx8mp-debix-som-a-bmb-08.dts | 470 ++++++++++++++++++
.../dts/freescale/imx8mp-debix-som-a.dtsi | 266 ++++++++++
3 files changed, 737 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index ef7d17aef58f0..ca7c9595e6ffa 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -91,6 +91,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-som-a-bmb-08.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
new file mode 100644
index 0000000000000..17028ab169717
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
@@ -0,0 +1,470 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel@pengutronix.de>
+ */
+
+/dts-v1/;
+
+#include "imx8mp-debix-som-a.dtsi"
+
+/ {
+ model = "Polyhex i.MX8MPlus Debix SOM A on BMB-08";
+ compatible = "polyhex,imx8mp-debix-som-a-bmb-08", "polyhex,imx8mp-debix-som-a",
+ "fsl,imx8mp";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "BB_VDD3V3";
+ gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
+ /* Required timings for ethernet phy's */
+ startup-delay-us = <50000>;
+ off-on-delay-us = <110000>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "BB_VDD5V";
+ gpio = <&expander0 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ regulator-som-vdd1v8 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "SOM_VDD1V8_SW";
+ gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ regulator-som-vdd3v3 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "SOM_VDD3V3_SW";
+ gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_usdhc2_vmmc: regulator-usdhc2 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ regulator-vbus-usb20 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "USB20_5V";
+ gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ vin-supply = <®_baseboard_vdd5v0>;
+ };
+
+ regulator-vbus-usb30 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "USB30_5V";
+ gpio = <&expander1 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ vin-supply = <®_baseboard_vdd5v0>;
+ };
+
+ reg_vdd5v0: regulator-vdd5v0 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-name = "VDD_5V";
+ gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&eqos {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_eqos>;
+ phy-supply = <®_baseboard_vdd3v3>;
+ phy-handle = <ðphy0>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <150000>;
+ eee-broken-1000t;
+ realtek,clkout-disable;
+ };
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-supply = <®_baseboard_vdd3v3>;
+ phy-handle = <ðphy1>;
+ phy-mode = "rgmii-id";
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <150000>;
+ eee-broken-1000t;
+ realtek,clkout-disable;
+ };
+ };
+};
+
+&flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_vdd5v0>;
+ status = "okay";
+};
+
+&flexcan2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_vdd5v0>;
+ status = "okay";
+};
+
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi0>;
+ status = "okay";
+
+ flash: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&i2c4 {
+ expander0: gpio@20 {
+ compatible = "nxp,pca9535";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <0x02>;
+ };
+
+ expander1: gpio@23 {
+ compatible = "nxp,pca9535";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <0x02>;
+
+ /*
+ * Since USB1 is bound to peripheral mode we need to ensure
+ * that VBUS is turned off.
+ */
+ usb30-otg-hog {
+ gpio-hog;
+ gpios = <13 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "USB30_OTG_EN";
+ };
+ };
+
+ eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ };
+
+ rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ #clock-cells = <0>;
+ };
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+/* Debug */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ dr_mode = "host";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ /* 2.x hub on port 1 */
+ usb_hub_2_x: hub@1 {
+ compatible = "usb5e3,610";
+ reg = <1>;
+ reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
+ vdd-supply = <®_vdd5v0>;
+ peer-hub = <&usb_hub_3_x>;
+ };
+
+ /* 3.x hub on port 2 */
+ usb_hub_3_x: hub@2 {
+ compatible = "usb5e3,620";
+ reg = <2>;
+ reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
+ vdd-supply = <®_vdd5v0>;
+ peer-hub = <&usb_hub_2_x>;
+ };
+};
+
+&usb3_phy0 {
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+/* µSD Card */
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
+ assigned-clock-rates = <400000000>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ bus-width = <4>;
+ disable-wp;
+ no-sdio;
+ no-mmc;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_eqos: eqosgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3
+ MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3
+ MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91
+ MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91
+ MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91
+ MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91
+ MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91
+ MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91
+ MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f
+ MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f
+ MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f
+ MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f
+ MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f
+ MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f
+
+ MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN 0x1f
+ MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x19
+ >;
+ };
+
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
+ MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3
+ MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91
+ MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91
+ MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91
+ MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91
+ MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91
+ MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
+ MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f
+ MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f
+ MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f
+ MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f
+ MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f
+ MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f
+ MX8MP_IOMUXC_SAI1_RXD0__ENET1_1588_EVENT1_IN 0x1f
+ MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x19
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX 0x154
+ MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX 0x154
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX 0x154
+ MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154
+ >;
+ };
+
+ pinctrl_flexspi0: flexspi0grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2
+ MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82
+ MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82
+ MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82
+ MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82
+ MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
+ MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3
+ MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_rtc: rtcgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x140
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f
+ MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x14f
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x49
+ MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x49
+ MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x49
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0
+ MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4
+ MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196
+ MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
+ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
+ MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
+ MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
+ MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
+ MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
new file mode 100644
index 0000000000000..a089cadacc105
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
@@ -0,0 +1,266 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel@pengutronix.de>
+ */
+
+#include "imx8mp.dtsi"
+
+/ {
+ model = "Polyhex i.MX8MPlus Debix SOM A";
+ compatible = "polyhex,imx8mp-debix-som-a", "fsl,imx8mp";
+};
+
+&A53_0 {
+ cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2>;
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic@25 {
+ compatible = "nxp,pca9450c";
+ reg = <0x25>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ buck1: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <2187500>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ buck2: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <2187500>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ };
+
+ buck4: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo5: LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ adc@48 {
+ compatible = "ti,ads1115";
+ reg = <0x48>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@4 {
+ reg = <4>;
+ ti,gain = <1>;
+ ti,datarate = <7>;
+ };
+ channel@5 {
+ reg = <5>;
+ ti,gain = <1>;
+ ti,datarate = <7>;
+ };
+ channel@6 {
+ reg = <6>;
+ ti,gain = <1>;
+ ti,datarate = <7>;
+ };
+ channel@7 {
+ reg = <7>;
+ ti,gain = <1>;
+ ti,datarate = <7>;
+ };
+ };
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
+ assigned-clock-rates = <400000000>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
+ MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3
+ MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
+ MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
+ MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6
+ MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6
+ MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6
+ MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6
+ MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6
+ MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6
+ MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6
+ MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6
+ MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.39.2
^ permalink raw reply related [flat|nested] 39+ messages in thread* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
2023-07-17 16:51 ` Marco Felsch
@ 2023-07-18 14:06 ` Fabio Estevam
-1 siblings, 0 replies; 39+ messages in thread
From: Fabio Estevam @ 2023-07-18 14:06 UTC (permalink / raw)
To: Marco Felsch
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, shawnguo, kernel,
linux-imx, laurent.pinchart, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
On Mon, Jul 17, 2023 at 1:51 PM Marco Felsch <m.felsch@pengutronix.de> wrote:
>
> Add support for the Debix SOM A + SOM A I/O board. The commit enables
> only the basic features like:
> - 2x UART
> - 2x Network
> - eMMC/µSD
> - CAN
> - QSPI
> - USB Host / Device
>
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
@ 2023-07-18 14:06 ` Fabio Estevam
0 siblings, 0 replies; 39+ messages in thread
From: Fabio Estevam @ 2023-07-18 14:06 UTC (permalink / raw)
To: Marco Felsch
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, shawnguo, kernel,
linux-imx, laurent.pinchart, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
On Mon, Jul 17, 2023 at 1:51 PM Marco Felsch <m.felsch@pengutronix.de> wrote:
>
> Add support for the Debix SOM A + SOM A I/O board. The commit enables
> only the basic features like:
> - 2x UART
> - 2x Network
> - eMMC/µSD
> - CAN
> - QSPI
> - USB Host / Device
>
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
2023-07-17 16:51 ` Marco Felsch
@ 2023-07-19 8:16 ` Shawn Guo
-1 siblings, 0 replies; 39+ messages in thread
From: Shawn Guo @ 2023-07-19 8:16 UTC (permalink / raw)
To: Marco Felsch
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, kernel, festevam,
linux-imx, laurent.pinchart, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:
> Add support for the Debix SOM A + SOM A I/O board. The commit enables
> only the basic features like:
> - 2x UART
> - 2x Network
> - eMMC/µSD
> - CAN
> - QSPI
> - USB Host / Device
>
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> ---
> Required patchsets:
>
> - usb: https://lore.kernel.org/all/20230623142228.4069084-1-m.felsch@pengutronix.de/
> - net: https://lore.kernel.org/all/20230717164307.2868264-1-m.felsch@pengutronix.de/
>
> Changelog:
>
> v2:
> - drop to generic polyhex,imx8mp-debix binding
> - net/phy: replace deprecated snps,reset-* and phy-reset-* bindings with
> new phy-node based ones
> - net/phy: fix phy properties and reset timings
> - net/phy: add fec phy-supply handling
> - net/phy: add eqos phy-supply handling
> - net/phy: fix baseboard-vdd3v3 timings to fulfill net-phy-timings
> - Fix spelling
> - Drop superfluous blank lines
> - pmic: make use of IRQ_TYPE_LEVEL_LOW
> - pmic: add whitespace between buck node name and '{'
>
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../freescale/imx8mp-debix-som-a-bmb-08.dts | 470 ++++++++++++++++++
> .../dts/freescale/imx8mp-debix-som-a.dtsi | 266 ++++++++++
> 3 files changed, 737 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index ef7d17aef58f0..ca7c9595e6ffa 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -91,6 +91,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-som-a-bmb-08.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> new file mode 100644
> index 0000000000000..17028ab169717
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> @@ -0,0 +1,470 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel@pengutronix.de>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mp-debix-som-a.dtsi"
> +
> +/ {
> + model = "Polyhex i.MX8MPlus Debix SOM A on BMB-08";
> + compatible = "polyhex,imx8mp-debix-som-a-bmb-08", "polyhex,imx8mp-debix-som-a",
> + "fsl,imx8mp";
> +
> + chosen {
> + stdout-path = &uart2;
> + };
> +
> + reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "BB_VDD3V3";
> + gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> + /* Required timings for ethernet phy's */
> + startup-delay-us = <50000>;
> + off-on-delay-us = <110000>;
> + enable-active-high;
Can we place this right after the line below?
gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + };
> +
> + reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "BB_VDD5V";
> + gpio = <&expander0 9 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + regulator-som-vdd1v8 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "SOM_VDD1V8_SW";
> + gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + regulator-som-vdd3v3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "SOM_VDD3V3_SW";
> + gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + reg_usdhc2_vmmc: regulator-usdhc2 {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + regulator-vbus-usb20 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "USB20_5V";
> + gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <®_baseboard_vdd5v0>;
> + };
> +
> + regulator-vbus-usb30 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "USB30_5V";
> + gpio = <&expander1 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <®_baseboard_vdd5v0>;
> + };
> +
> + reg_vdd5v0: regulator-vdd5v0 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "VDD_5V";
> + gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&eqos {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_eqos>;
> + phy-supply = <®_baseboard_vdd3v3>;
> + phy-handle = <ðphy0>;
> + phy-mode = "rgmii-id";
> + status = "okay";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <20000>;
> + reset-deassert-us = <150000>;
> + eee-broken-1000t;
> + realtek,clkout-disable;
> + };
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-supply = <®_baseboard_vdd3v3>;
> + phy-handle = <ðphy1>;
> + phy-mode = "rgmii-id";
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <20000>;
> + reset-deassert-us = <150000>;
> + eee-broken-1000t;
> + realtek,clkout-disable;
> + };
> + };
> +};
> +
> +&flexcan1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + xceiver-supply = <®_vdd5v0>;
> + status = "okay";
> +};
> +
> +&flexcan2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + xceiver-supply = <®_vdd5v0>;
> + status = "okay";
> +};
> +
> +&flexspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi0>;
> + status = "okay";
> +
> + flash: flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <80000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
> +
> +&i2c4 {
> + expander0: gpio@20 {
> + compatible = "nxp,pca9535";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <0x02>;
> + };
> +
> + expander1: gpio@23 {
> + compatible = "nxp,pca9535";
> + reg = <0x23>;
> + gpio-controller;
> + #gpio-cells = <0x02>;
> +
> + /*
> + * Since USB1 is bound to peripheral mode we need to ensure
> + * that VBUS is turned off.
> + */
> + usb30-otg-hog {
> + gpio-hog;
> + gpios = <13 GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "USB30_OTG_EN";
> + };
> + };
> +
> + eeprom@52 {
> + compatible = "atmel,24c02";
> + reg = <0x52>;
> + pagesize = <16>;
> + };
> +
> + rtc@51 {
Sort them in order of unit-address.
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rtc>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> + #clock-cells = <0>;
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +/* Debug */
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&usb3_0 {
> + status = "okay";
> +};
> +
> +&usb3_1 {
> + status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> + dr_mode = "host";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + /* 2.x hub on port 1 */
> + usb_hub_2_x: hub@1 {
> + compatible = "usb5e3,610";
> + reg = <1>;
> + reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
> + vdd-supply = <®_vdd5v0>;
> + peer-hub = <&usb_hub_3_x>;
> + };
> +
> + /* 3.x hub on port 2 */
> + usb_hub_3_x: hub@2 {
> + compatible = "usb5e3,620";
> + reg = <2>;
> + reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
> + vdd-supply = <®_vdd5v0>;
> + peer-hub = <&usb_hub_2_x>;
> + };
> +};
> +
> +&usb3_phy0 {
> + status = "okay";
> +};
> +
> +&usb3_phy1 {
> + status = "okay";
> +};
> +
> +/* µSD Card */
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> + assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
> + assigned-clock-rates = <400000000>;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + bus-width = <4>;
> + disable-wp;
> + no-sdio;
> + no-mmc;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_eqos: eqosgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3
> + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3
> + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91
> + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91
> + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91
> + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91
> + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91
> + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91
> + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f
> + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f
> + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f
> + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f
> + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f
> + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f
> +
> + MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN 0x1f
> + MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x19
> + >;
> + };
> +
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
> + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3
> + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91
> + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91
> + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91
> + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91
> + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91
> + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
> + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f
> + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f
> + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f
> + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f
> + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f
> + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f
> + MX8MP_IOMUXC_SAI1_RXD0__ENET1_1588_EVENT1_IN 0x1f
> + MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x19
> + >;
> + };
> +
> + pinctrl_flexcan1: flexcan1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX 0x154
> + MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX 0x154
> + >;
> + };
> +
> + pinctrl_flexcan2: flexcan2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX 0x154
> + MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154
> + >;
> + };
> +
> + pinctrl_flexspi0: flexspi0grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2
> + MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82
> + MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82
> + MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82
> + MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82
> + MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
> + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2
> + >;
> + };
> +
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3
> + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_rtc: rtcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x140
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f
> + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x14f
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x49
> + MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x49
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x49
> + MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x49
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> new file mode 100644
> index 0000000000000..a089cadacc105
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> @@ -0,0 +1,266 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel@pengutronix.de>
> + */
> +
> +#include "imx8mp.dtsi"
> +
> +/ {
> + model = "Polyhex i.MX8MPlus Debix SOM A";
> + compatible = "polyhex,imx8mp-debix-som-a", "fsl,imx8mp";
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic@25 {
> + compatible = "nxp,pca9450c";
> + reg = <0x25>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + buck1: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + buck2: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + };
> +
> + buck4: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck5: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck6: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo5: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&i2c4 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c4>;
> + status = "okay";
> +
> + adc@48 {
> + compatible = "ti,ads1115";
> + reg = <0x48>;
> +
Unnecessary newline.
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel@4 {
> + reg = <4>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
Have a newline between nodes.
Shawn
> + channel@5 {
> + reg = <5>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + channel@6 {
> + reg = <6>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + channel@7 {
> + reg = <7>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
> + assigned-clock-rates = <400000000>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
> + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2
> + >;
> + };
> +
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3
> + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6
> + >;
> + };
> +};
> --
> 2.39.2
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
@ 2023-07-19 8:16 ` Shawn Guo
0 siblings, 0 replies; 39+ messages in thread
From: Shawn Guo @ 2023-07-19 8:16 UTC (permalink / raw)
To: Marco Felsch
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, kernel, festevam,
linux-imx, laurent.pinchart, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:
> Add support for the Debix SOM A + SOM A I/O board. The commit enables
> only the basic features like:
> - 2x UART
> - 2x Network
> - eMMC/µSD
> - CAN
> - QSPI
> - USB Host / Device
>
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> ---
> Required patchsets:
>
> - usb: https://lore.kernel.org/all/20230623142228.4069084-1-m.felsch@pengutronix.de/
> - net: https://lore.kernel.org/all/20230717164307.2868264-1-m.felsch@pengutronix.de/
>
> Changelog:
>
> v2:
> - drop to generic polyhex,imx8mp-debix binding
> - net/phy: replace deprecated snps,reset-* and phy-reset-* bindings with
> new phy-node based ones
> - net/phy: fix phy properties and reset timings
> - net/phy: add fec phy-supply handling
> - net/phy: add eqos phy-supply handling
> - net/phy: fix baseboard-vdd3v3 timings to fulfill net-phy-timings
> - Fix spelling
> - Drop superfluous blank lines
> - pmic: make use of IRQ_TYPE_LEVEL_LOW
> - pmic: add whitespace between buck node name and '{'
>
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../freescale/imx8mp-debix-som-a-bmb-08.dts | 470 ++++++++++++++++++
> .../dts/freescale/imx8mp-debix-som-a.dtsi | 266 ++++++++++
> 3 files changed, 737 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index ef7d17aef58f0..ca7c9595e6ffa 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -91,6 +91,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-som-a-bmb-08.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> new file mode 100644
> index 0000000000000..17028ab169717
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> @@ -0,0 +1,470 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel@pengutronix.de>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mp-debix-som-a.dtsi"
> +
> +/ {
> + model = "Polyhex i.MX8MPlus Debix SOM A on BMB-08";
> + compatible = "polyhex,imx8mp-debix-som-a-bmb-08", "polyhex,imx8mp-debix-som-a",
> + "fsl,imx8mp";
> +
> + chosen {
> + stdout-path = &uart2;
> + };
> +
> + reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "BB_VDD3V3";
> + gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> + /* Required timings for ethernet phy's */
> + startup-delay-us = <50000>;
> + off-on-delay-us = <110000>;
> + enable-active-high;
Can we place this right after the line below?
gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> + regulator-always-on;
> + };
> +
> + reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "BB_VDD5V";
> + gpio = <&expander0 9 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + regulator-som-vdd1v8 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "SOM_VDD1V8_SW";
> + gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + regulator-som-vdd3v3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "SOM_VDD3V3_SW";
> + gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + reg_usdhc2_vmmc: regulator-usdhc2 {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + regulator-vbus-usb20 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "USB20_5V";
> + gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <®_baseboard_vdd5v0>;
> + };
> +
> + regulator-vbus-usb30 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "USB30_5V";
> + gpio = <&expander1 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <®_baseboard_vdd5v0>;
> + };
> +
> + reg_vdd5v0: regulator-vdd5v0 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "VDD_5V";
> + gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&eqos {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_eqos>;
> + phy-supply = <®_baseboard_vdd3v3>;
> + phy-handle = <ðphy0>;
> + phy-mode = "rgmii-id";
> + status = "okay";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <20000>;
> + reset-deassert-us = <150000>;
> + eee-broken-1000t;
> + realtek,clkout-disable;
> + };
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-supply = <®_baseboard_vdd3v3>;
> + phy-handle = <ðphy1>;
> + phy-mode = "rgmii-id";
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <20000>;
> + reset-deassert-us = <150000>;
> + eee-broken-1000t;
> + realtek,clkout-disable;
> + };
> + };
> +};
> +
> +&flexcan1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + xceiver-supply = <®_vdd5v0>;
> + status = "okay";
> +};
> +
> +&flexcan2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + xceiver-supply = <®_vdd5v0>;
> + status = "okay";
> +};
> +
> +&flexspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi0>;
> + status = "okay";
> +
> + flash: flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <80000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
> +
> +&i2c4 {
> + expander0: gpio@20 {
> + compatible = "nxp,pca9535";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <0x02>;
> + };
> +
> + expander1: gpio@23 {
> + compatible = "nxp,pca9535";
> + reg = <0x23>;
> + gpio-controller;
> + #gpio-cells = <0x02>;
> +
> + /*
> + * Since USB1 is bound to peripheral mode we need to ensure
> + * that VBUS is turned off.
> + */
> + usb30-otg-hog {
> + gpio-hog;
> + gpios = <13 GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "USB30_OTG_EN";
> + };
> + };
> +
> + eeprom@52 {
> + compatible = "atmel,24c02";
> + reg = <0x52>;
> + pagesize = <16>;
> + };
> +
> + rtc@51 {
Sort them in order of unit-address.
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rtc>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> + #clock-cells = <0>;
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +/* Debug */
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&usb3_0 {
> + status = "okay";
> +};
> +
> +&usb3_1 {
> + status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> + dr_mode = "host";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + /* 2.x hub on port 1 */
> + usb_hub_2_x: hub@1 {
> + compatible = "usb5e3,610";
> + reg = <1>;
> + reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
> + vdd-supply = <®_vdd5v0>;
> + peer-hub = <&usb_hub_3_x>;
> + };
> +
> + /* 3.x hub on port 2 */
> + usb_hub_3_x: hub@2 {
> + compatible = "usb5e3,620";
> + reg = <2>;
> + reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
> + vdd-supply = <®_vdd5v0>;
> + peer-hub = <&usb_hub_2_x>;
> + };
> +};
> +
> +&usb3_phy0 {
> + status = "okay";
> +};
> +
> +&usb3_phy1 {
> + status = "okay";
> +};
> +
> +/* µSD Card */
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> + assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
> + assigned-clock-rates = <400000000>;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + bus-width = <4>;
> + disable-wp;
> + no-sdio;
> + no-mmc;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_eqos: eqosgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3
> + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3
> + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91
> + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91
> + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91
> + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91
> + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91
> + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91
> + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f
> + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f
> + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f
> + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f
> + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f
> + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f
> +
> + MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN 0x1f
> + MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x19
> + >;
> + };
> +
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
> + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3
> + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91
> + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91
> + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91
> + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91
> + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91
> + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
> + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f
> + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f
> + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f
> + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f
> + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f
> + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f
> + MX8MP_IOMUXC_SAI1_RXD0__ENET1_1588_EVENT1_IN 0x1f
> + MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x19
> + >;
> + };
> +
> + pinctrl_flexcan1: flexcan1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX 0x154
> + MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX 0x154
> + >;
> + };
> +
> + pinctrl_flexcan2: flexcan2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX 0x154
> + MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154
> + >;
> + };
> +
> + pinctrl_flexspi0: flexspi0grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2
> + MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82
> + MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82
> + MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82
> + MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82
> + MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
> + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2
> + >;
> + };
> +
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3
> + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_rtc: rtcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x140
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f
> + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x14f
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x49
> + MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x49
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x49
> + MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x49
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> new file mode 100644
> index 0000000000000..a089cadacc105
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> @@ -0,0 +1,266 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel@pengutronix.de>
> + */
> +
> +#include "imx8mp.dtsi"
> +
> +/ {
> + model = "Polyhex i.MX8MPlus Debix SOM A";
> + compatible = "polyhex,imx8mp-debix-som-a", "fsl,imx8mp";
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic@25 {
> + compatible = "nxp,pca9450c";
> + reg = <0x25>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + buck1: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + buck2: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + };
> +
> + buck4: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck5: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck6: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo5: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&i2c4 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c4>;
> + status = "okay";
> +
> + adc@48 {
> + compatible = "ti,ads1115";
> + reg = <0x48>;
> +
Unnecessary newline.
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel@4 {
> + reg = <4>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
Have a newline between nodes.
Shawn
> + channel@5 {
> + reg = <5>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + channel@6 {
> + reg = <6>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + channel@7 {
> + reg = <7>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
> + assigned-clock-rates = <400000000>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
> + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2
> + >;
> + };
> +
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3
> + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6
> + >;
> + };
> +};
> --
> 2.39.2
>
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
2023-07-19 8:16 ` Shawn Guo
@ 2023-07-19 9:18 ` Marco Felsch
-1 siblings, 0 replies; 39+ messages in thread
From: Marco Felsch @ 2023-07-19 9:18 UTC (permalink / raw)
To: Shawn Guo
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, kernel, festevam,
linux-imx, laurent.pinchart, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
Hi Shawn,
On 23-07-19, Shawn Guo wrote:
> On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:
...
> > + reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "BB_VDD3V3";
> > + gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> > + /* Required timings for ethernet phy's */
> > + startup-delay-us = <50000>;
> > + off-on-delay-us = <110000>;
> > + enable-active-high;
>
> Can we place this right after the line below?
>
> gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
Sure.
> > + regulator-always-on;
> > + };
...
> > +&i2c4 {
> > + expander0: gpio@20 {
> > + compatible = "nxp,pca9535";
> > + reg = <0x20>;
> > + gpio-controller;
> > + #gpio-cells = <0x02>;
> > + };
> > +
> > + expander1: gpio@23 {
> > + compatible = "nxp,pca9535";
> > + reg = <0x23>;
> > + gpio-controller;
> > + #gpio-cells = <0x02>;
> > +
> > + /*
> > + * Since USB1 is bound to peripheral mode we need to ensure
> > + * that VBUS is turned off.
> > + */
> > + usb30-otg-hog {
> > + gpio-hog;
> > + gpios = <13 GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "USB30_OTG_EN";
> > + };
> > + };
> > +
> > + eeprom@52 {
> > + compatible = "atmel,24c02";
> > + reg = <0x52>;
> > + pagesize = <16>;
> > + };
> > +
> > + rtc@51 {
>
> Sort them in order of unit-address.
Of course, thanks.
> > + compatible = "haoyu,hym8563";
> > + reg = <0x51>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_rtc>;
> > + interrupt-parent = <&gpio4>;
> > + interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> > + #clock-cells = <0>;
> > + };
> > +};
> > +&i2c4 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c4>;
> > + status = "okay";
> > +
> > + adc@48 {
> > + compatible = "ti,ads1115";
> > + reg = <0x48>;
> > +
>
> Unnecessary newline.
Dropped it, thanks.
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + channel@4 {
> > + reg = <4>;
> > + ti,gain = <1>;
> > + ti,datarate = <7>;
> > + };
>
> Have a newline between nodes.
Sure.
Regards,
Marco
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
@ 2023-07-19 9:18 ` Marco Felsch
0 siblings, 0 replies; 39+ messages in thread
From: Marco Felsch @ 2023-07-19 9:18 UTC (permalink / raw)
To: Shawn Guo
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, kernel, festevam,
linux-imx, laurent.pinchart, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
Hi Shawn,
On 23-07-19, Shawn Guo wrote:
> On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:
...
> > + reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "BB_VDD3V3";
> > + gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> > + /* Required timings for ethernet phy's */
> > + startup-delay-us = <50000>;
> > + off-on-delay-us = <110000>;
> > + enable-active-high;
>
> Can we place this right after the line below?
>
> gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
Sure.
> > + regulator-always-on;
> > + };
...
> > +&i2c4 {
> > + expander0: gpio@20 {
> > + compatible = "nxp,pca9535";
> > + reg = <0x20>;
> > + gpio-controller;
> > + #gpio-cells = <0x02>;
> > + };
> > +
> > + expander1: gpio@23 {
> > + compatible = "nxp,pca9535";
> > + reg = <0x23>;
> > + gpio-controller;
> > + #gpio-cells = <0x02>;
> > +
> > + /*
> > + * Since USB1 is bound to peripheral mode we need to ensure
> > + * that VBUS is turned off.
> > + */
> > + usb30-otg-hog {
> > + gpio-hog;
> > + gpios = <13 GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "USB30_OTG_EN";
> > + };
> > + };
> > +
> > + eeprom@52 {
> > + compatible = "atmel,24c02";
> > + reg = <0x52>;
> > + pagesize = <16>;
> > + };
> > +
> > + rtc@51 {
>
> Sort them in order of unit-address.
Of course, thanks.
> > + compatible = "haoyu,hym8563";
> > + reg = <0x51>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_rtc>;
> > + interrupt-parent = <&gpio4>;
> > + interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> > + #clock-cells = <0>;
> > + };
> > +};
> > +&i2c4 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c4>;
> > + status = "okay";
> > +
> > + adc@48 {
> > + compatible = "ti,ads1115";
> > + reg = <0x48>;
> > +
>
> Unnecessary newline.
Dropped it, thanks.
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + channel@4 {
> > + reg = <4>;
> > + ti,gain = <1>;
> > + ti,datarate = <7>;
> > + };
>
> Have a newline between nodes.
Sure.
Regards,
Marco
^ permalink raw reply [flat|nested] 39+ messages in thread
* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
2023-07-17 16:51 ` Marco Felsch
` (2 preceding siblings ...)
(?)
@ 2023-07-25 13:26 ` Laurent Pinchart
2023-07-31 8:51 ` Marco Felsch
-1 siblings, 1 reply; 39+ messages in thread
From: Laurent Pinchart @ 2023-07-25 13:26 UTC (permalink / raw)
To: Marco Felsch
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, shawnguo, kernel,
festevam, linux-imx, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
Hi Marco,
Thank you for the patch.
On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:
> Add support for the Debix SOM A + SOM A I/O board. The commit enables
> only the basic features like:
> - 2x UART
> - 2x Network
> - eMMC/µSD
> - CAN
> - QSPI
> - USB Host / Device
>
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> ---
> Required patchsets:
>
> - usb: https://lore.kernel.org/all/20230623142228.4069084-1-m.felsch@pengutronix.de/
> - net: https://lore.kernel.org/all/20230717164307.2868264-1-m.felsch@pengutronix.de/
>
> Changelog:
>
> v2:
> - drop to generic polyhex,imx8mp-debix binding
> - net/phy: replace deprecated snps,reset-* and phy-reset-* bindings with
> new phy-node based ones
> - net/phy: fix phy properties and reset timings
> - net/phy: add fec phy-supply handling
> - net/phy: add eqos phy-supply handling
> - net/phy: fix baseboard-vdd3v3 timings to fulfill net-phy-timings
> - Fix spelling
> - Drop superfluous blank lines
> - pmic: make use of IRQ_TYPE_LEVEL_LOW
> - pmic: add whitespace between buck node name and '{'
>
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../freescale/imx8mp-debix-som-a-bmb-08.dts | 470 ++++++++++++++++++
> .../dts/freescale/imx8mp-debix-som-a.dtsi | 266 ++++++++++
> 3 files changed, 737 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index ef7d17aef58f0..ca7c9595e6ffa 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -91,6 +91,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-som-a-bmb-08.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk3.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> new file mode 100644
> index 0000000000000..17028ab169717
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a-bmb-08.dts
> @@ -0,0 +1,470 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel@pengutronix.de>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mp-debix-som-a.dtsi"
> +
> +/ {
> + model = "Polyhex i.MX8MPlus Debix SOM A on BMB-08";
> + compatible = "polyhex,imx8mp-debix-som-a-bmb-08", "polyhex,imx8mp-debix-som-a",
> + "fsl,imx8mp";
> +
> + chosen {
> + stdout-path = &uart2;
> + };
> +
> + reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "BB_VDD3V3";
> + gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> + /* Required timings for ethernet phy's */
> + startup-delay-us = <50000>;
The regulator's datasheet shows a much smaller delay (about 1500µs with
a 3A load).
> + off-on-delay-us = <110000>;
Is this really a property of the regulator ? Or a requirement of the
ethernet PHY ? In the latter case, shouldn't it be handled by the PHY ?
> + enable-active-high;
> + regulator-always-on;
Why always on ? Same for the other supplies.
> + };
> +
> + reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "BB_VDD5V";
> + gpio = <&expander0 9 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + regulator-som-vdd1v8 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "SOM_VDD1V8_SW";
> + gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + regulator-som-vdd3v3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "SOM_VDD3V3_SW";
> + gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + reg_usdhc2_vmmc: regulator-usdhc2 {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
This seems to be produced by the SoM, it should be moved to the SoM
.dtsi.
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + regulator-vbus-usb20 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "USB20_5V";
> + gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <®_baseboard_vdd5v0>;
> + };
> +
> + regulator-vbus-usb30 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "USB30_5V";
> + gpio = <&expander1 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <®_baseboard_vdd5v0>;
> + };
> +
> + reg_vdd5v0: regulator-vdd5v0 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-name = "VDD_5V";
> + gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&eqos {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_eqos>;
> + phy-supply = <®_baseboard_vdd3v3>;
> + phy-handle = <ðphy0>;
> + phy-mode = "rgmii-id";
> + status = "okay";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@0 {
Unless I'm mistaken, the PHYs are both at address 1. Address 0 works as
it's the broadcast address, but is there a good reason not to use the
real address ? Same below.
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <20000>;
> + reset-deassert-us = <150000>;
> + eee-broken-1000t;
> + realtek,clkout-disable;
> + };
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-supply = <®_baseboard_vdd3v3>;
> + phy-handle = <ðphy1>;
> + phy-mode = "rgmii-id";
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <20000>;
> + reset-deassert-us = <150000>;
> + eee-broken-1000t;
> + realtek,clkout-disable;
> + };
> + };
> +};
> +
> +&flexcan1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + xceiver-supply = <®_vdd5v0>;
> + status = "okay";
> +};
> +
> +&flexcan2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + xceiver-supply = <®_vdd5v0>;
> + status = "okay";
> +};
> +
> +&flexspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi0>;
> + status = "okay";
> +
> + flash: flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <80000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <4>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
> +
> +&i2c4 {
> + expander0: gpio@20 {
> + compatible = "nxp,pca9535";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <0x02>;
> + };
> +
> + expander1: gpio@23 {
> + compatible = "nxp,pca9535";
> + reg = <0x23>;
> + gpio-controller;
> + #gpio-cells = <0x02>;
> +
> + /*
> + * Since USB1 is bound to peripheral mode we need to ensure
> + * that VBUS is turned off.
> + */
> + usb30-otg-hog {
> + gpio-hog;
> + gpios = <13 GPIO_ACTIVE_HIGH>;
> + output-low;
> + line-name = "USB30_OTG_EN";
> + };
> + };
> +
> + eeprom@52 {
> + compatible = "atmel,24c02";
> + reg = <0x52>;
> + pagesize = <16>;
> + };
> +
> + rtc@51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rtc>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> + #clock-cells = <0>;
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +/* Debug */
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&usb3_0 {
> + status = "okay";
> +};
> +
> +&usb3_1 {
> + status = "okay";
> +};
> +
> +&usb_dwc3_0 {
> + dr_mode = "peripheral";
> + status = "okay";
> +};
> +
> +&usb_dwc3_1 {
> + dr_mode = "host";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + /* 2.x hub on port 1 */
> + usb_hub_2_x: hub@1 {
> + compatible = "usb5e3,610";
> + reg = <1>;
> + reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
> + vdd-supply = <®_vdd5v0>;
> + peer-hub = <&usb_hub_3_x>;
> + };
> +
> + /* 3.x hub on port 2 */
> + usb_hub_3_x: hub@2 {
> + compatible = "usb5e3,620";
> + reg = <2>;
> + reset-gpios = <&expander1 9 GPIO_ACTIVE_LOW>;
> + vdd-supply = <®_vdd5v0>;
> + peer-hub = <&usb_hub_2_x>;
> + };
> +};
> +
> +&usb3_phy0 {
> + status = "okay";
> +};
> +
> +&usb3_phy1 {
> + status = "okay";
> +};
> +
> +/* µSD Card */
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> + assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
> + assigned-clock-rates = <400000000>;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + bus-width = <4>;
> + disable-wp;
> + no-sdio;
> + no-mmc;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_eqos: eqosgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3
> + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3
> + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91
> + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91
> + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91
> + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91
> + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91
> + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91
> + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f
> + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f
> + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f
> + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f
> + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f
> + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f
> +
> + MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN 0x1f
> + MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x19
> + >;
> + };
> +
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3
> + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3
> + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91
> + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91
> + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91
> + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91
> + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91
> + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91
> + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f
> + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f
> + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f
> + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f
> + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f
> + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f
> + MX8MP_IOMUXC_SAI1_RXD0__ENET1_1588_EVENT1_IN 0x1f
> + MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x19
> + >;
> + };
> +
> + pinctrl_flexcan1: flexcan1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX 0x154
> + MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX 0x154
> + >;
> + };
> +
> + pinctrl_flexcan2: flexcan2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX 0x154
> + MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX 0x154
> + >;
> + };
> +
> + pinctrl_flexspi0: flexspi0grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2
> + MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82
> + MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82
> + MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82
> + MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82
> + MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
> + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2
> + >;
> + };
> +
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3
> + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_rtc: rtcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x140
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f
> + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x14f
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x49
> + MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x49
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x49
> + MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x49
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196
> + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6
> + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
> + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
> + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
> + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
> + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> new file mode 100644
> index 0000000000000..a089cadacc105
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi
> @@ -0,0 +1,266 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2019 NXP
> + * Copyright (C) 2023 Pengutronix, Marco Felsch <kernel@pengutronix.de>
> + */
> +
> +#include "imx8mp.dtsi"
> +
> +/ {
> + model = "Polyhex i.MX8MPlus Debix SOM A";
> + compatible = "polyhex,imx8mp-debix-som-a", "fsl,imx8mp";
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic@25 {
> + compatible = "nxp,pca9450c";
> + reg = <0x25>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + buck1: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + buck2: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + };
> +
> + buck4: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck5: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck6: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo5: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&i2c4 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c4>;
> + status = "okay";
> +
> + adc@48 {
> + compatible = "ti,ads1115";
> + reg = <0x48>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + channel@4 {
> + reg = <4>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + channel@5 {
> + reg = <5>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + channel@6 {
> + reg = <6>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + channel@7 {
> + reg = <7>;
> + ti,gain = <1>;
> + ti,datarate = <7>;
> + };
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
> + assigned-clock-rates = <400000000>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2
> + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2
> + >;
> + };
> +
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3
> + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196
> + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6
> + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6
> + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6
> + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6
> + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6
> + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6
> + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6
> + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6
> + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6
> + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6
> + >;
> + };
> +};
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
2023-07-25 13:26 ` Laurent Pinchart
@ 2023-07-31 8:51 ` Marco Felsch
0 siblings, 0 replies; 39+ messages in thread
From: Marco Felsch @ 2023-07-31 8:51 UTC (permalink / raw)
To: Laurent Pinchart
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, shawnguo, kernel,
festevam, linux-imx, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
Hi Laurent,
On 23-07-25, Laurent Pinchart wrote:
> Hi Marco,
>
> Thank you for the patch.
>
> On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:
...
> > + reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "BB_VDD3V3";
> > + gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> > + /* Required timings for ethernet phy's */
> > + startup-delay-us = <50000>;
>
> The regulator's datasheet shows a much smaller delay (about 1500µs with
> a 3A load).
>
> > + off-on-delay-us = <110000>;
>
> Is this really a property of the regulator ? Or a requirement of the
> ethernet PHY ? In the latter case, shouldn't it be handled by the PHY ?
As written in the above comment: the delays are required by the PHYs.
> > + enable-active-high;
> > + regulator-always-on;
>
> Why always on ? Same for the other supplies.
I don't have the SoM schematics and I wanted to keep it simple while
porting the downstream DTS. For this regulator we can drop the
'regulator-alaways-on' property but for the others I rather tend to keep
it. As this is an EVK this board should never made it into real products
and so power-consumption/optimization isn't really important.
> > + };
> > +
> > + reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-name = "BB_VDD5V";
> > + gpio = <&expander0 9 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + regulator-som-vdd1v8 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "SOM_VDD1V8_SW";
> > + gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > +
> > + regulator-som-vdd3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "SOM_VDD3V3_SW";
> > + gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usdhc2_vmmc: regulator-usdhc2 {
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> > + regulator-name = "VSD_3V3";
>
> This seems to be produced by the SoM, it should be moved to the SoM
> .dtsi.
You're right, albeit the arrow is pointing to J6. I'll fix this.
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + regulator-vbus-usb20 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-name = "USB20_5V";
> > + gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + vin-supply = <®_baseboard_vdd5v0>;
> > + };
> > +
> > + regulator-vbus-usb30 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-name = "USB30_5V";
> > + gpio = <&expander1 12 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + vin-supply = <®_baseboard_vdd5v0>;
> > + };
> > +
> > + reg_vdd5v0: regulator-vdd5v0 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-name = "VDD_5V";
> > + gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +};
> > +
> > +&eqos {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_eqos>;
> > + phy-supply = <®_baseboard_vdd3v3>;
> > + phy-handle = <ðphy0>;
> > + phy-mode = "rgmii-id";
> > + status = "okay";
> > +
> > + mdio {
> > + compatible = "snps,dwmac-mdio";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ethphy0: ethernet-phy@0 {
>
> Unless I'm mistaken, the PHYs are both at address 1. Address 0 works as
> it's the broadcast address, but is there a good reason not to use the
> real address ? Same below.
Didn't verified the phy-addr since it was working after respecting the
power-delays. I will give it a try and assign the correct address.
Regards,
Marco
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 39+ messages in thread* Re: [PATCH v2 4/4] arm64: dts: freescale: Add DEBIX SOM A and SOM A I/O Board support
@ 2023-07-31 8:51 ` Marco Felsch
0 siblings, 0 replies; 39+ messages in thread
From: Marco Felsch @ 2023-07-31 8:51 UTC (permalink / raw)
To: Laurent Pinchart
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, shawnguo, kernel,
festevam, linux-imx, dan.scally, devicetree, linux-kernel,
linux-arm-kernel
Hi Laurent,
On 23-07-25, Laurent Pinchart wrote:
> Hi Marco,
>
> Thank you for the patch.
>
> On Mon, Jul 17, 2023 at 06:51:27PM +0200, Marco Felsch wrote:
...
> > + reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "BB_VDD3V3";
> > + gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
> > + /* Required timings for ethernet phy's */
> > + startup-delay-us = <50000>;
>
> The regulator's datasheet shows a much smaller delay (about 1500µs with
> a 3A load).
>
> > + off-on-delay-us = <110000>;
>
> Is this really a property of the regulator ? Or a requirement of the
> ethernet PHY ? In the latter case, shouldn't it be handled by the PHY ?
As written in the above comment: the delays are required by the PHYs.
> > + enable-active-high;
> > + regulator-always-on;
>
> Why always on ? Same for the other supplies.
I don't have the SoM schematics and I wanted to keep it simple while
porting the downstream DTS. For this regulator we can drop the
'regulator-alaways-on' property but for the others I rather tend to keep
it. As this is an EVK this board should never made it into real products
and so power-consumption/optimization isn't really important.
> > + };
> > +
> > + reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-name = "BB_VDD5V";
> > + gpio = <&expander0 9 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + regulator-som-vdd1v8 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "SOM_VDD1V8_SW";
> > + gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > +
> > + regulator-som-vdd3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "SOM_VDD3V3_SW";
> > + gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usdhc2_vmmc: regulator-usdhc2 {
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> > + regulator-name = "VSD_3V3";
>
> This seems to be produced by the SoM, it should be moved to the SoM
> .dtsi.
You're right, albeit the arrow is pointing to J6. I'll fix this.
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + regulator-vbus-usb20 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-name = "USB20_5V";
> > + gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + vin-supply = <®_baseboard_vdd5v0>;
> > + };
> > +
> > + regulator-vbus-usb30 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-name = "USB30_5V";
> > + gpio = <&expander1 12 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + vin-supply = <®_baseboard_vdd5v0>;
> > + };
> > +
> > + reg_vdd5v0: regulator-vdd5v0 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-name = "VDD_5V";
> > + gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +};
> > +
> > +&eqos {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_eqos>;
> > + phy-supply = <®_baseboard_vdd3v3>;
> > + phy-handle = <ðphy0>;
> > + phy-mode = "rgmii-id";
> > + status = "okay";
> > +
> > + mdio {
> > + compatible = "snps,dwmac-mdio";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ethphy0: ethernet-phy@0 {
>
> Unless I'm mistaken, the PHYs are both at address 1. Address 0 works as
> it's the broadcast address, but is there a good reason not to use the
> real address ? Same below.
Didn't verified the phy-addr since it was working after respecting the
power-delays. I will give it a try and assign the correct address.
Regards,
Marco
^ permalink raw reply [flat|nested] 39+ messages in thread