* [PATCH v9 0/2] ARM: dts: Facebook Yosemite 4 platform @ 2023-08-10 7:00 ` Delphine CC Chiu 0 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: linux-aspeed Add linux device tree entry related to Yosemite 4 specific devices connected to BMC SoC. Changelog: v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum v8 - Add description of Yosemite 4 - Remove unsupported ncsi config - Revise i2c-mux config - Correct power sensor i2c address - Restore i2c 11 bus-frequency to default v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 v5 - Revise rtc setting - Remove duplicated multi-master setting v4 - Resend with cover letter v3 - Revise the bootargs to stdout-path - Revise i2c devices v2 - Revise the DTS node name v1 - Add binding document Delphine CC Chiu (2): dt-bindings: arm: aspeed: add Facebook Yosemite 4 board ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC .../bindings/arm/aspeed/aspeed.yaml | 1 + arch/arm/boot/dts/aspeed/Makefile | 1 + .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 624 ++++++++++++++++++ 3 files changed, 626 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts -- 2.25.1 ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v9 0/2] ARM: dts: Facebook Yosemite 4 platform @ 2023-08-10 7:00 ` Delphine CC Chiu 0 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: patrick Cc: Delphine CC Chiu, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel Add linux device tree entry related to Yosemite 4 specific devices connected to BMC SoC. Changelog: v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum v8 - Add description of Yosemite 4 - Remove unsupported ncsi config - Revise i2c-mux config - Correct power sensor i2c address - Restore i2c 11 bus-frequency to default v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 v5 - Revise rtc setting - Remove duplicated multi-master setting v4 - Resend with cover letter v3 - Revise the bootargs to stdout-path - Revise i2c devices v2 - Revise the DTS node name v1 - Add binding document Delphine CC Chiu (2): dt-bindings: arm: aspeed: add Facebook Yosemite 4 board ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC .../bindings/arm/aspeed/aspeed.yaml | 1 + arch/arm/boot/dts/aspeed/Makefile | 1 + .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 624 ++++++++++++++++++ 3 files changed, 626 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts -- 2.25.1 ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v9 0/2] ARM: dts: Facebook Yosemite 4 platform @ 2023-08-10 7:00 ` Delphine CC Chiu 0 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: patrick Cc: Delphine CC Chiu, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel Add linux device tree entry related to Yosemite 4 specific devices connected to BMC SoC. Changelog: v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum v8 - Add description of Yosemite 4 - Remove unsupported ncsi config - Revise i2c-mux config - Correct power sensor i2c address - Restore i2c 11 bus-frequency to default v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 v5 - Revise rtc setting - Remove duplicated multi-master setting v4 - Resend with cover letter v3 - Revise the bootargs to stdout-path - Revise i2c devices v2 - Revise the DTS node name v1 - Add binding document Delphine CC Chiu (2): dt-bindings: arm: aspeed: add Facebook Yosemite 4 board ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC .../bindings/arm/aspeed/aspeed.yaml | 1 + arch/arm/boot/dts/aspeed/Makefile | 1 + .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 624 ++++++++++++++++++ 3 files changed, 626 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board 2023-08-10 7:00 ` Delphine CC Chiu (?) @ 2023-08-10 7:00 ` Delphine CC Chiu -1 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: linux-aspeed Document the new compatibles used on Facebook Yosemite 4. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Changelog: v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 --- Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml index e0eff4c05879..23ee325bfed0 100644 --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml @@ -79,6 +79,7 @@ properties: - facebook,elbert-bmc - facebook,fuji-bmc - facebook,greatlakes-bmc + - facebook,yosemite4-bmc - ibm,everest-bmc - ibm,rainier-bmc - ibm,tacoma-bmc -- 2.25.1 ^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board @ 2023-08-10 7:00 ` Delphine CC Chiu 0 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: patrick, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery Cc: Delphine CC Chiu, Krzysztof Kozlowski, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel Document the new compatibles used on Facebook Yosemite 4. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Changelog: v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 --- Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml index e0eff4c05879..23ee325bfed0 100644 --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml @@ -79,6 +79,7 @@ properties: - facebook,elbert-bmc - facebook,fuji-bmc - facebook,greatlakes-bmc + - facebook,yosemite4-bmc - ibm,everest-bmc - ibm,rainier-bmc - ibm,tacoma-bmc -- 2.25.1 ^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board @ 2023-08-10 7:00 ` Delphine CC Chiu 0 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: patrick, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery Cc: Delphine CC Chiu, Krzysztof Kozlowski, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel Document the new compatibles used on Facebook Yosemite 4. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Changelog: v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 --- Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml index e0eff4c05879..23ee325bfed0 100644 --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml @@ -79,6 +79,7 @@ properties: - facebook,elbert-bmc - facebook,fuji-bmc - facebook,greatlakes-bmc + - facebook,yosemite4-bmc - ibm,everest-bmc - ibm,rainier-bmc - ibm,tacoma-bmc -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board 2023-08-10 7:00 ` Delphine CC Chiu (?) @ 2023-08-10 7:20 ` Rob Herring -1 siblings, 0 replies; 15+ messages in thread From: Rob Herring @ 2023-08-10 7:20 UTC (permalink / raw) To: linux-aspeed On Thu, 10 Aug 2023 15:00:29 +0800, Delphine CC Chiu wrote: > Document the new compatibles used on Facebook Yosemite 4. > > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > --- > Changelog: > v7 - Revise changelog format > v6 - Change project name from yosemitev4 to yosemite4 > --- > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + > 1 file changed, 1 insertion(+) > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230810070032.335161-2-Delphine_CC_Chiu at wiwynn.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema. ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board @ 2023-08-10 7:20 ` Rob Herring 0 siblings, 0 replies; 15+ messages in thread From: Rob Herring @ 2023-08-10 7:20 UTC (permalink / raw) To: Delphine CC Chiu Cc: Conor Dooley, Rob Herring, linux-arm-kernel, Krzysztof Kozlowski, Krzysztof Kozlowski, Joel Stanley, linux-aspeed, patrick, devicetree, Andrew Jeffery, linux-kernel On Thu, 10 Aug 2023 15:00:29 +0800, Delphine CC Chiu wrote: > Document the new compatibles used on Facebook Yosemite 4. > > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > --- > Changelog: > v7 - Revise changelog format > v6 - Change project name from yosemitev4 to yosemite4 > --- > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + > 1 file changed, 1 insertion(+) > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230810070032.335161-2-Delphine_CC_Chiu@wiwynn.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema. ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board @ 2023-08-10 7:20 ` Rob Herring 0 siblings, 0 replies; 15+ messages in thread From: Rob Herring @ 2023-08-10 7:20 UTC (permalink / raw) To: Delphine CC Chiu Cc: Conor Dooley, Rob Herring, linux-arm-kernel, Krzysztof Kozlowski, Krzysztof Kozlowski, Joel Stanley, linux-aspeed, patrick, devicetree, Andrew Jeffery, linux-kernel On Thu, 10 Aug 2023 15:00:29 +0800, Delphine CC Chiu wrote: > Document the new compatibles used on Facebook Yosemite 4. > > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > --- > Changelog: > v7 - Revise changelog format > v6 - Change project name from yosemitev4 to yosemite4 > --- > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + > 1 file changed, 1 insertion(+) > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230810070032.335161-2-Delphine_CC_Chiu@wiwynn.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema. _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board 2023-08-10 7:20 ` Rob Herring (?) @ 2023-08-10 20:40 ` Rob Herring -1 siblings, 0 replies; 15+ messages in thread From: Rob Herring @ 2023-08-10 20:40 UTC (permalink / raw) To: linux-aspeed On Thu, Aug 10, 2023 at 01:20:21AM -0600, Rob Herring wrote: > > On Thu, 10 Aug 2023 15:00:29 +0800, Delphine CC Chiu wrote: > > Document the new compatibles used on Facebook Yosemite 4. > > > > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> > > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > > --- > > Changelog: > > v7 - Revise changelog format > > v6 - Change project name from yosemitev4 to yosemite4 > > --- > > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + > > 1 file changed, 1 insertion(+) > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > > > doc reference errors (make refcheckdocs): > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230810070032.335161-2-Delphine_CC_Chiu at wiwynn.com The bot was having an issue. This can be ignored. Rob ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board @ 2023-08-10 20:40 ` Rob Herring 0 siblings, 0 replies; 15+ messages in thread From: Rob Herring @ 2023-08-10 20:40 UTC (permalink / raw) To: Delphine CC Chiu Cc: Conor Dooley, linux-arm-kernel, Krzysztof Kozlowski, Krzysztof Kozlowski, Joel Stanley, linux-aspeed, patrick, devicetree, Andrew Jeffery, linux-kernel On Thu, Aug 10, 2023 at 01:20:21AM -0600, Rob Herring wrote: > > On Thu, 10 Aug 2023 15:00:29 +0800, Delphine CC Chiu wrote: > > Document the new compatibles used on Facebook Yosemite 4. > > > > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> > > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > > --- > > Changelog: > > v7 - Revise changelog format > > v6 - Change project name from yosemitev4 to yosemite4 > > --- > > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + > > 1 file changed, 1 insertion(+) > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > > > doc reference errors (make refcheckdocs): > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230810070032.335161-2-Delphine_CC_Chiu@wiwynn.com The bot was having an issue. This can be ignored. Rob ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board @ 2023-08-10 20:40 ` Rob Herring 0 siblings, 0 replies; 15+ messages in thread From: Rob Herring @ 2023-08-10 20:40 UTC (permalink / raw) To: Delphine CC Chiu Cc: Conor Dooley, linux-arm-kernel, Krzysztof Kozlowski, Krzysztof Kozlowski, Joel Stanley, linux-aspeed, patrick, devicetree, Andrew Jeffery, linux-kernel On Thu, Aug 10, 2023 at 01:20:21AM -0600, Rob Herring wrote: > > On Thu, 10 Aug 2023 15:00:29 +0800, Delphine CC Chiu wrote: > > Document the new compatibles used on Facebook Yosemite 4. > > > > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> > > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > > --- > > Changelog: > > v7 - Revise changelog format > > v6 - Change project name from yosemitev4 to yosemite4 > > --- > > Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + > > 1 file changed, 1 insertion(+) > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > > > doc reference errors (make refcheckdocs): > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230810070032.335161-2-Delphine_CC_Chiu@wiwynn.com The bot was having an issue. This can be ignored. Rob _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v9 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC 2023-08-10 7:00 ` Delphine CC Chiu (?) @ 2023-08-10 7:00 ` Delphine CC Chiu -1 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: linux-aspeed Add linux device tree entry for Yosemite 4 devices connected to BMC. The Yosemite 4 is a Meta multi-node server platform, based on AST2600 SoC. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Joel Stanley <joel@jms.id.au> --- Changelog: v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum v8 - Add description of Yosemite 4 - Remove unsupported ncsi config - Revise i2c-mux config - Correct power sensor i2c address - Restore i2c 11 bus-frequency to default v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 v5 - Revise rtc setting - Remove duplicated multi-master setting v3 - Revise the bootargs to stdout-path - Revise i2c devices v2 - Revise the DTS node name --- arch/arm/boot/dts/aspeed/Makefile | 1 + .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 624 ++++++++++++++++++ 2 files changed, 625 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile index c68984322a86..5b9264b823f3 100644 --- a/arch/arm/boot/dts/aspeed/Makefile +++ b/arch/arm/boot/dts/aspeed/Makefile @@ -26,6 +26,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-facebook-wedge400.dtb \ aspeed-bmc-facebook-yamp.dtb \ aspeed-bmc-facebook-yosemitev2.dtb \ + aspeed-bmc-facebook-yosemite4.dtb \ aspeed-bmc-ibm-bonnell.dtb \ aspeed-bmc-ibm-everest.dtb \ aspeed-bmc-ibm-rainier.dtb \ diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts new file mode 100644 index 000000000000..64075cc41d92 --- /dev/null +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts @@ -0,0 +1,624 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright 2022 Facebook Inc. + +/dts-v1/; +#include "aspeed-g6.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> +#include <dt-bindings/leds/leds-pca955x.h> +#include <dt-bindings/i2c/i2c.h> + +/ { + model = "Facebook Yosemite 4 BMC"; + compatible = "facebook,yosemite4-bmc", "aspeed,ast2600"; + + aliases { + serial4 = &uart5; + serial5 = &uart6; + serial6 = &uart7; + serial7 = &uart8; + serial8 = &uart9; + }; + + chosen { + stdout-path = "serial4:57600n8"; + }; + + memory at 80000000 { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>, + <&adc1 0>, <&adc1 1>; + }; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&uart6 { + status = "okay"; +}; + +&uart7 { + status = "okay"; +}; + +&uart8 { + status = "okay"; +}; + +&uart9 { + status = "okay"; +}; + +&wdt1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdtrst1_default>; + aspeed,reset-type = "soc"; + aspeed,external-signal; + aspeed,ext-push-pull; + aspeed,ext-active-high; + aspeed,ext-pulse-duration = <256>; +}; + +&mac2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii3_default>; + use-ncsi; + mlx,multi-host; +}; + +&mac3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii4_default>; + use-ncsi; + mlx,multi-host; +}; + +&fmc { + status = "okay"; + flash at 0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-rx-bus-width = <4>; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout-64.dtsi" + }; + flash at 1 { + status = "okay"; + m25p,fast-read; + label = "bmc2"; + spi-rx-bus-width = <4>; + spi-max-frequency = <50000000>; + }; +}; + +&i2c0 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor at 40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c1 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor at 40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c2 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor at 40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c3 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor at 40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c4 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor at 40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c5 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor at 40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c6 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor at 40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c7 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor at 40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c8 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux at 70 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x70>; + }; +}; + +&i2c9 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux at 71 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x71>; + }; +}; + +&i2c10 { + status = "okay"; + bus-frequency = <400000>; +}; + +&i2c11 { + status = "okay"; + power-sensor at 10 { + compatible = "adi, adm1272"; + reg = <0x10>; + }; + + power-sensor at 12 { + compatible = "adi, adm1272"; + reg = <0x12>; + }; + + gpio at 20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio at 21 { + compatible = "nxp,pca9555"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio at 22 { + compatible = "nxp,pca9555"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio at 23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + temperature-sensor at 48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; + + temperature-sensor at 49 { + compatible = "ti,tmp75"; + reg = <0x49>; + }; + + temperature-sensor at 4a { + compatible = "ti,tmp75"; + reg = <0x4a>; + }; + + temperature-sensor at 4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; + + eeprom at 54 { + compatible = "atmel,24c256"; + reg = <0x54>; + }; +}; + +&i2c12 { + status = "okay"; + bus-frequency = <400000>; + + temperature-sensor at 48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; + + eeprom at 50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + rtc at 6f { + compatible = "nuvoton,nct3018y"; + reg = <0x6f>; + }; +}; + +&i2c13 { + status = "okay"; + bus-frequency = <400000>; +}; + +&i2c14 { + status = "okay"; + bus-frequency = <400000>; + adc at 1d { + compatible = "ti,adc128d818"; + reg = <0x1d>; + ti,mode = /bits/ 8 <2>; + }; + + adc at 35 { + compatible = "ti,adc128d818"; + reg = <0x35>; + ti,mode = /bits/ 8 <2>; + }; + + adc at 37 { + compatible = "ti,adc128d818"; + reg = <0x37>; + ti,mode = /bits/ 8 <2>; + }; + + power-sensor at 40 { + compatible = "ti,ina230"; + reg = <0x40>; + }; + + power-sensor at 41 { + compatible = "ti,ina230"; + reg = <0x41>; + }; + + power-sensor at 42 { + compatible = "ti,ina230"; + reg = <0x42>; + }; + + power-sensor at 43 { + compatible = "ti,ina230"; + reg = <0x43>; + }; + + power-sensor at 44 { + compatible = "ti,ina230"; + reg = <0x44>; + }; + + temperature-sensor at 4e { + compatible = "ti,tmp75"; + reg = <0x4e>; + }; + + temperature-sensor at 4f { + compatible = "ti,tmp75"; + reg = <0x4f>; + }; + + eeprom at 51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + i2c-mux at 71 { + compatible = "nxp,pca9846"; + #address-cells = <1>; + #size-cells = <0>; + + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x71>; + + i2c at 0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc at 1f { + compatible = "ti,adc128d818"; + reg = <0x1f>; + ti,mode = /bits/ 8 <2>; + }; + + pwm at 20{ + compatible = "max31790"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + gpio at 22{ + compatible = "ti,tca6424"; + reg = <0x22>; + }; + + pwm at 23{ + compatible = "max31790"; + reg = <0x23>; + #address-cells = <1>; + #size-cells = <0>; + }; + + adc at 33 { + compatible = "maxim,max11615"; + reg = <0x33>; + }; + + eeprom at 52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; + + gpio at 61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + i2c at 1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc at 1f { + compatible = "ti,adc128d818"; + reg = <0x1f>; + ti,mode = /bits/ 8 <2>; + }; + + pwm at 20{ + compatible = "max31790"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + gpio at 22{ + compatible = "ti,tca6424"; + reg = <0x22>; + }; + + pwm at 23{ + compatible = "max31790"; + reg = <0x23>; + #address-cells = <1>; + #size-cells = <0>; + }; + + adc at 33 { + compatible = "maxim,max11615"; + reg = <0x33>; + }; + + eeprom at 52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; + + gpio at 61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + }; + + i2c-mux at 73 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x73>; + + i2c at 0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc at 35 { + compatible = "maxim,max11617"; + reg = <0x35>; + }; + }; + + i2c at 1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc at 35 { + compatible = "maxim,max11617"; + reg = <0x35>; + }; + }; + }; +}; + +&i2c15 { + status = "okay"; + mctp-controller; + multi-master; + bus-frequency = <400000>; + + mctp at 10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + i2c-mux at 72 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x72>; + }; +}; + +&adc0 { + ref_voltage = <2500>; + status = "okay"; + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default + &pinctrl_adc2_default &pinctrl_adc3_default + &pinctrl_adc4_default &pinctrl_adc5_default + &pinctrl_adc6_default &pinctrl_adc7_default>; +}; + +&adc1 { + ref_voltage = <2500>; + status = "okay"; + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>; +}; + + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&uhci { + status = "okay"; +}; -- 2.25.1 ^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v9 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC @ 2023-08-10 7:00 ` Delphine CC Chiu 0 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: patrick, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery Cc: Delphine CC Chiu, Krzysztof Kozlowski, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel Add linux device tree entry for Yosemite 4 devices connected to BMC. The Yosemite 4 is a Meta multi-node server platform, based on AST2600 SoC. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Joel Stanley <joel@jms.id.au> --- Changelog: v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum v8 - Add description of Yosemite 4 - Remove unsupported ncsi config - Revise i2c-mux config - Correct power sensor i2c address - Restore i2c 11 bus-frequency to default v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 v5 - Revise rtc setting - Remove duplicated multi-master setting v3 - Revise the bootargs to stdout-path - Revise i2c devices v2 - Revise the DTS node name --- arch/arm/boot/dts/aspeed/Makefile | 1 + .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 624 ++++++++++++++++++ 2 files changed, 625 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile index c68984322a86..5b9264b823f3 100644 --- a/arch/arm/boot/dts/aspeed/Makefile +++ b/arch/arm/boot/dts/aspeed/Makefile @@ -26,6 +26,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-facebook-wedge400.dtb \ aspeed-bmc-facebook-yamp.dtb \ aspeed-bmc-facebook-yosemitev2.dtb \ + aspeed-bmc-facebook-yosemite4.dtb \ aspeed-bmc-ibm-bonnell.dtb \ aspeed-bmc-ibm-everest.dtb \ aspeed-bmc-ibm-rainier.dtb \ diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts new file mode 100644 index 000000000000..64075cc41d92 --- /dev/null +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts @@ -0,0 +1,624 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright 2022 Facebook Inc. + +/dts-v1/; +#include "aspeed-g6.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> +#include <dt-bindings/leds/leds-pca955x.h> +#include <dt-bindings/i2c/i2c.h> + +/ { + model = "Facebook Yosemite 4 BMC"; + compatible = "facebook,yosemite4-bmc", "aspeed,ast2600"; + + aliases { + serial4 = &uart5; + serial5 = &uart6; + serial6 = &uart7; + serial7 = &uart8; + serial8 = &uart9; + }; + + chosen { + stdout-path = "serial4:57600n8"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>, + <&adc1 0>, <&adc1 1>; + }; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&uart6 { + status = "okay"; +}; + +&uart7 { + status = "okay"; +}; + +&uart8 { + status = "okay"; +}; + +&uart9 { + status = "okay"; +}; + +&wdt1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdtrst1_default>; + aspeed,reset-type = "soc"; + aspeed,external-signal; + aspeed,ext-push-pull; + aspeed,ext-active-high; + aspeed,ext-pulse-duration = <256>; +}; + +&mac2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii3_default>; + use-ncsi; + mlx,multi-host; +}; + +&mac3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii4_default>; + use-ncsi; + mlx,multi-host; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-rx-bus-width = <4>; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout-64.dtsi" + }; + flash@1 { + status = "okay"; + m25p,fast-read; + label = "bmc2"; + spi-rx-bus-width = <4>; + spi-max-frequency = <50000000>; + }; +}; + +&i2c0 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c1 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c2 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c3 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c4 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c5 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c6 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c7 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c8 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux@70 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x70>; + }; +}; + +&i2c9 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux@71 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x71>; + }; +}; + +&i2c10 { + status = "okay"; + bus-frequency = <400000>; +}; + +&i2c11 { + status = "okay"; + power-sensor@10 { + compatible = "adi, adm1272"; + reg = <0x10>; + }; + + power-sensor@12 { + compatible = "adi, adm1272"; + reg = <0x12>; + }; + + gpio@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@21 { + compatible = "nxp,pca9555"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@22 { + compatible = "nxp,pca9555"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + temperature-sensor@48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; + + temperature-sensor@49 { + compatible = "ti,tmp75"; + reg = <0x49>; + }; + + temperature-sensor@4a { + compatible = "ti,tmp75"; + reg = <0x4a>; + }; + + temperature-sensor@4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; + + eeprom@54 { + compatible = "atmel,24c256"; + reg = <0x54>; + }; +}; + +&i2c12 { + status = "okay"; + bus-frequency = <400000>; + + temperature-sensor@48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + rtc@6f { + compatible = "nuvoton,nct3018y"; + reg = <0x6f>; + }; +}; + +&i2c13 { + status = "okay"; + bus-frequency = <400000>; +}; + +&i2c14 { + status = "okay"; + bus-frequency = <400000>; + adc@1d { + compatible = "ti,adc128d818"; + reg = <0x1d>; + ti,mode = /bits/ 8 <2>; + }; + + adc@35 { + compatible = "ti,adc128d818"; + reg = <0x35>; + ti,mode = /bits/ 8 <2>; + }; + + adc@37 { + compatible = "ti,adc128d818"; + reg = <0x37>; + ti,mode = /bits/ 8 <2>; + }; + + power-sensor@40 { + compatible = "ti,ina230"; + reg = <0x40>; + }; + + power-sensor@41 { + compatible = "ti,ina230"; + reg = <0x41>; + }; + + power-sensor@42 { + compatible = "ti,ina230"; + reg = <0x42>; + }; + + power-sensor@43 { + compatible = "ti,ina230"; + reg = <0x43>; + }; + + power-sensor@44 { + compatible = "ti,ina230"; + reg = <0x44>; + }; + + temperature-sensor@4e { + compatible = "ti,tmp75"; + reg = <0x4e>; + }; + + temperature-sensor@4f { + compatible = "ti,tmp75"; + reg = <0x4f>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + i2c-mux@71 { + compatible = "nxp,pca9846"; + #address-cells = <1>; + #size-cells = <0>; + + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x71>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@1f { + compatible = "ti,adc128d818"; + reg = <0x1f>; + ti,mode = /bits/ 8 <2>; + }; + + pwm@20{ + compatible = "max31790"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + gpio@22{ + compatible = "ti,tca6424"; + reg = <0x22>; + }; + + pwm@23{ + compatible = "max31790"; + reg = <0x23>; + #address-cells = <1>; + #size-cells = <0>; + }; + + adc@33 { + compatible = "maxim,max11615"; + reg = <0x33>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; + + gpio@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@1f { + compatible = "ti,adc128d818"; + reg = <0x1f>; + ti,mode = /bits/ 8 <2>; + }; + + pwm@20{ + compatible = "max31790"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + gpio@22{ + compatible = "ti,tca6424"; + reg = <0x22>; + }; + + pwm@23{ + compatible = "max31790"; + reg = <0x23>; + #address-cells = <1>; + #size-cells = <0>; + }; + + adc@33 { + compatible = "maxim,max11615"; + reg = <0x33>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; + + gpio@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + }; + + i2c-mux@73 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x73>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@35 { + compatible = "maxim,max11617"; + reg = <0x35>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@35 { + compatible = "maxim,max11617"; + reg = <0x35>; + }; + }; + }; +}; + +&i2c15 { + status = "okay"; + mctp-controller; + multi-master; + bus-frequency = <400000>; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + i2c-mux@72 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x72>; + }; +}; + +&adc0 { + ref_voltage = <2500>; + status = "okay"; + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default + &pinctrl_adc2_default &pinctrl_adc3_default + &pinctrl_adc4_default &pinctrl_adc5_default + &pinctrl_adc6_default &pinctrl_adc7_default>; +}; + +&adc1 { + ref_voltage = <2500>; + status = "okay"; + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>; +}; + + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&uhci { + status = "okay"; +}; -- 2.25.1 ^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH v9 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC @ 2023-08-10 7:00 ` Delphine CC Chiu 0 siblings, 0 replies; 15+ messages in thread From: Delphine CC Chiu @ 2023-08-10 7:00 UTC (permalink / raw) To: patrick, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery Cc: Delphine CC Chiu, Krzysztof Kozlowski, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel Add linux device tree entry for Yosemite 4 devices connected to BMC. The Yosemite 4 is a Meta multi-node server platform, based on AST2600 SoC. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Joel Stanley <joel@jms.id.au> --- Changelog: v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum v8 - Add description of Yosemite 4 - Remove unsupported ncsi config - Revise i2c-mux config - Correct power sensor i2c address - Restore i2c 11 bus-frequency to default v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 v5 - Revise rtc setting - Remove duplicated multi-master setting v3 - Revise the bootargs to stdout-path - Revise i2c devices v2 - Revise the DTS node name --- arch/arm/boot/dts/aspeed/Makefile | 1 + .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 624 ++++++++++++++++++ 2 files changed, 625 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile index c68984322a86..5b9264b823f3 100644 --- a/arch/arm/boot/dts/aspeed/Makefile +++ b/arch/arm/boot/dts/aspeed/Makefile @@ -26,6 +26,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-facebook-wedge400.dtb \ aspeed-bmc-facebook-yamp.dtb \ aspeed-bmc-facebook-yosemitev2.dtb \ + aspeed-bmc-facebook-yosemite4.dtb \ aspeed-bmc-ibm-bonnell.dtb \ aspeed-bmc-ibm-everest.dtb \ aspeed-bmc-ibm-rainier.dtb \ diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts new file mode 100644 index 000000000000..64075cc41d92 --- /dev/null +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts @@ -0,0 +1,624 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright 2022 Facebook Inc. + +/dts-v1/; +#include "aspeed-g6.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> +#include <dt-bindings/leds/leds-pca955x.h> +#include <dt-bindings/i2c/i2c.h> + +/ { + model = "Facebook Yosemite 4 BMC"; + compatible = "facebook,yosemite4-bmc", "aspeed,ast2600"; + + aliases { + serial4 = &uart5; + serial5 = &uart6; + serial6 = &uart7; + serial7 = &uart8; + serial8 = &uart9; + }; + + chosen { + stdout-path = "serial4:57600n8"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>, + <&adc1 0>, <&adc1 1>; + }; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&uart6 { + status = "okay"; +}; + +&uart7 { + status = "okay"; +}; + +&uart8 { + status = "okay"; +}; + +&uart9 { + status = "okay"; +}; + +&wdt1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdtrst1_default>; + aspeed,reset-type = "soc"; + aspeed,external-signal; + aspeed,ext-push-pull; + aspeed,ext-active-high; + aspeed,ext-pulse-duration = <256>; +}; + +&mac2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii3_default>; + use-ncsi; + mlx,multi-host; +}; + +&mac3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii4_default>; + use-ncsi; + mlx,multi-host; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-rx-bus-width = <4>; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout-64.dtsi" + }; + flash@1 { + status = "okay"; + m25p,fast-read; + label = "bmc2"; + spi-rx-bus-width = <4>; + spi-max-frequency = <50000000>; + }; +}; + +&i2c0 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c1 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c2 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c3 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c4 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c5 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c6 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c7 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c8 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux@70 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x70>; + }; +}; + +&i2c9 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux@71 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x71>; + }; +}; + +&i2c10 { + status = "okay"; + bus-frequency = <400000>; +}; + +&i2c11 { + status = "okay"; + power-sensor@10 { + compatible = "adi, adm1272"; + reg = <0x10>; + }; + + power-sensor@12 { + compatible = "adi, adm1272"; + reg = <0x12>; + }; + + gpio@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@21 { + compatible = "nxp,pca9555"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@22 { + compatible = "nxp,pca9555"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + temperature-sensor@48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; + + temperature-sensor@49 { + compatible = "ti,tmp75"; + reg = <0x49>; + }; + + temperature-sensor@4a { + compatible = "ti,tmp75"; + reg = <0x4a>; + }; + + temperature-sensor@4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; + + eeprom@54 { + compatible = "atmel,24c256"; + reg = <0x54>; + }; +}; + +&i2c12 { + status = "okay"; + bus-frequency = <400000>; + + temperature-sensor@48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + rtc@6f { + compatible = "nuvoton,nct3018y"; + reg = <0x6f>; + }; +}; + +&i2c13 { + status = "okay"; + bus-frequency = <400000>; +}; + +&i2c14 { + status = "okay"; + bus-frequency = <400000>; + adc@1d { + compatible = "ti,adc128d818"; + reg = <0x1d>; + ti,mode = /bits/ 8 <2>; + }; + + adc@35 { + compatible = "ti,adc128d818"; + reg = <0x35>; + ti,mode = /bits/ 8 <2>; + }; + + adc@37 { + compatible = "ti,adc128d818"; + reg = <0x37>; + ti,mode = /bits/ 8 <2>; + }; + + power-sensor@40 { + compatible = "ti,ina230"; + reg = <0x40>; + }; + + power-sensor@41 { + compatible = "ti,ina230"; + reg = <0x41>; + }; + + power-sensor@42 { + compatible = "ti,ina230"; + reg = <0x42>; + }; + + power-sensor@43 { + compatible = "ti,ina230"; + reg = <0x43>; + }; + + power-sensor@44 { + compatible = "ti,ina230"; + reg = <0x44>; + }; + + temperature-sensor@4e { + compatible = "ti,tmp75"; + reg = <0x4e>; + }; + + temperature-sensor@4f { + compatible = "ti,tmp75"; + reg = <0x4f>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + i2c-mux@71 { + compatible = "nxp,pca9846"; + #address-cells = <1>; + #size-cells = <0>; + + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x71>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@1f { + compatible = "ti,adc128d818"; + reg = <0x1f>; + ti,mode = /bits/ 8 <2>; + }; + + pwm@20{ + compatible = "max31790"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + gpio@22{ + compatible = "ti,tca6424"; + reg = <0x22>; + }; + + pwm@23{ + compatible = "max31790"; + reg = <0x23>; + #address-cells = <1>; + #size-cells = <0>; + }; + + adc@33 { + compatible = "maxim,max11615"; + reg = <0x33>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; + + gpio@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@1f { + compatible = "ti,adc128d818"; + reg = <0x1f>; + ti,mode = /bits/ 8 <2>; + }; + + pwm@20{ + compatible = "max31790"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + gpio@22{ + compatible = "ti,tca6424"; + reg = <0x22>; + }; + + pwm@23{ + compatible = "max31790"; + reg = <0x23>; + #address-cells = <1>; + #size-cells = <0>; + }; + + adc@33 { + compatible = "maxim,max11615"; + reg = <0x33>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; + + gpio@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + }; + + i2c-mux@73 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x73>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@35 { + compatible = "maxim,max11617"; + reg = <0x35>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@35 { + compatible = "maxim,max11617"; + reg = <0x35>; + }; + }; + }; +}; + +&i2c15 { + status = "okay"; + mctp-controller; + multi-master; + bus-frequency = <400000>; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + i2c-mux@72 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x72>; + }; +}; + +&adc0 { + ref_voltage = <2500>; + status = "okay"; + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default + &pinctrl_adc2_default &pinctrl_adc3_default + &pinctrl_adc4_default &pinctrl_adc5_default + &pinctrl_adc6_default &pinctrl_adc7_default>; +}; + +&adc1 { + ref_voltage = <2500>; + status = "okay"; + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>; +}; + + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&uhci { + status = "okay"; +}; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 15+ messages in thread
end of thread, other threads:[~2023-08-10 20:41 UTC | newest] Thread overview: 15+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2023-08-10 7:00 [PATCH v9 0/2] ARM: dts: Facebook Yosemite 4 platform Delphine CC Chiu 2023-08-10 7:00 ` Delphine CC Chiu 2023-08-10 7:00 ` Delphine CC Chiu 2023-08-10 7:00 ` [PATCH v9 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board Delphine CC Chiu 2023-08-10 7:00 ` Delphine CC Chiu 2023-08-10 7:00 ` Delphine CC Chiu 2023-08-10 7:20 ` Rob Herring 2023-08-10 7:20 ` Rob Herring 2023-08-10 7:20 ` Rob Herring 2023-08-10 20:40 ` Rob Herring 2023-08-10 20:40 ` Rob Herring 2023-08-10 20:40 ` Rob Herring 2023-08-10 7:00 ` [PATCH v9 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC Delphine CC Chiu 2023-08-10 7:00 ` Delphine CC Chiu 2023-08-10 7:00 ` Delphine CC Chiu
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.