All of lore.kernel.org
 help / color / mirror / Atom feed
From: Tony Lindgren <tony@atomide.com>
To: linux-omap@vger.kernel.org
Cc: Dhruva Gole <d-gole@ti.com>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Keerthy <j-keerthy@ti.com>, Kevin Hilman <khilman@baylibre.com>,
	Nishanth Menon <nm@ti.com>,
	linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH] bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up
Date: Thu,  7 Sep 2023 08:54:41 +0300	[thread overview]
Message-ID: <20230907055441.19476-1-tony@atomide.com> (raw)

The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of
SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE
is used to force idle target modules rather than block idle during usage.

The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when
a target module is active, and configure autoidle and wake-up when a
target module is inactive. We are missing configuring the target module
on sysc_disable_module(), and missing toggling of the wake-up bit.

Let's fix the issue to allow uart wake-up to work.

Fixes: fb685f1c190e ("bus: ti-sysc: Handle swsup idle mode quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 drivers/bus/ti-sysc.c | 22 +++++++++++++++++-----
 1 file changed, 17 insertions(+), 5 deletions(-)

diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c
--- a/drivers/bus/ti-sysc.c
+++ b/drivers/bus/ti-sysc.c
@@ -1097,6 +1097,11 @@ static int sysc_enable_module(struct device *dev)
 	if (ddata->cfg.quirks & (SYSC_QUIRK_SWSUP_SIDLE |
 				 SYSC_QUIRK_SWSUP_SIDLE_ACT)) {
 		best_mode = SYSC_IDLE_NO;
+
+		/* Clear WAKEUP */
+		if (regbits->enwkup_shift >= 0 &&
+		    ddata->cfg.sysc_val & BIT(regbits->enwkup_shift))
+			reg &= ~BIT(regbits->enwkup_shift);
 	} else {
 		best_mode = fls(ddata->cfg.sidlemodes) - 1;
 		if (best_mode > SYSC_IDLE_MASK) {
@@ -1224,6 +1229,13 @@ static int sysc_disable_module(struct device *dev)
 		}
 	}
 
+	if (ddata->cfg.quirks & SYSC_QUIRK_SWSUP_SIDLE_ACT) {
+		/* Set WAKEUP */
+		if (regbits->enwkup_shift >= 0 &&
+		    ddata->cfg.sysc_val & BIT(regbits->enwkup_shift))
+			reg |= BIT(regbits->enwkup_shift);
+	}
+
 	reg &= ~(SYSC_IDLE_MASK << regbits->sidle_shift);
 	reg |= best_mode << regbits->sidle_shift;
 	if (regbits->autoidle_shift >= 0 &&
@@ -1518,16 +1530,16 @@ struct sysc_revision_quirk {
 static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 	/* These drivers need to be fixed to not use pm_runtime_irq_safe() */
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000046, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000052, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	/* Uarts on omap4 and later */
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x50411e03, 0xffff00ff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47422e03, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47424e03, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 
 	/* Quirks that need to be set based on the module address */
 	SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -ENODEV, 0x50000800, 0xffffffff,
-- 
2.41.0

WARNING: multiple messages have this Message-ID (diff)
From: Tony Lindgren <tony@atomide.com>
To: linux-omap@vger.kernel.org
Cc: Dhruva Gole <d-gole@ti.com>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Keerthy <j-keerthy@ti.com>, Kevin Hilman <khilman@baylibre.com>,
	Nishanth Menon <nm@ti.com>,
	linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH] bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up
Date: Thu,  7 Sep 2023 08:54:41 +0300	[thread overview]
Message-ID: <20230907055441.19476-1-tony@atomide.com> (raw)

The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of
SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE
is used to force idle target modules rather than block idle during usage.

The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when
a target module is active, and configure autoidle and wake-up when a
target module is inactive. We are missing configuring the target module
on sysc_disable_module(), and missing toggling of the wake-up bit.

Let's fix the issue to allow uart wake-up to work.

Fixes: fb685f1c190e ("bus: ti-sysc: Handle swsup idle mode quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 drivers/bus/ti-sysc.c | 22 +++++++++++++++++-----
 1 file changed, 17 insertions(+), 5 deletions(-)

diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c
--- a/drivers/bus/ti-sysc.c
+++ b/drivers/bus/ti-sysc.c
@@ -1097,6 +1097,11 @@ static int sysc_enable_module(struct device *dev)
 	if (ddata->cfg.quirks & (SYSC_QUIRK_SWSUP_SIDLE |
 				 SYSC_QUIRK_SWSUP_SIDLE_ACT)) {
 		best_mode = SYSC_IDLE_NO;
+
+		/* Clear WAKEUP */
+		if (regbits->enwkup_shift >= 0 &&
+		    ddata->cfg.sysc_val & BIT(regbits->enwkup_shift))
+			reg &= ~BIT(regbits->enwkup_shift);
 	} else {
 		best_mode = fls(ddata->cfg.sidlemodes) - 1;
 		if (best_mode > SYSC_IDLE_MASK) {
@@ -1224,6 +1229,13 @@ static int sysc_disable_module(struct device *dev)
 		}
 	}
 
+	if (ddata->cfg.quirks & SYSC_QUIRK_SWSUP_SIDLE_ACT) {
+		/* Set WAKEUP */
+		if (regbits->enwkup_shift >= 0 &&
+		    ddata->cfg.sysc_val & BIT(regbits->enwkup_shift))
+			reg |= BIT(regbits->enwkup_shift);
+	}
+
 	reg &= ~(SYSC_IDLE_MASK << regbits->sidle_shift);
 	reg |= best_mode << regbits->sidle_shift;
 	if (regbits->autoidle_shift >= 0 &&
@@ -1518,16 +1530,16 @@ struct sysc_revision_quirk {
 static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 	/* These drivers need to be fixed to not use pm_runtime_irq_safe() */
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000046, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000052, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	/* Uarts on omap4 and later */
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x50411e03, 0xffff00ff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47422e03, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 	SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x47424e03, 0xffffffff,
-		   SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE),
+		   SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE),
 
 	/* Quirks that need to be set based on the module address */
 	SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -ENODEV, 0x50000800, 0xffffffff,
-- 
2.41.0

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2023-09-07 16:08 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-09-07  5:54 Tony Lindgren [this message]
2023-09-07  5:54 ` [PATCH] bus: ti-sysc: Fix SYSC_QUIRK_SWSUP_SIDLE_ACT handling for uart wake-up Tony Lindgren
2023-09-07  6:22 ` Dhruva Gole
2023-09-07  6:22   ` Dhruva Gole
2023-09-07  6:22   ` Dhruva Gole
2023-09-12 22:40   ` Kevin Hilman
2023-09-12 22:40     ` Kevin Hilman
2023-09-13  8:26     ` Tony Lindgren
2023-09-13  8:26       ` Tony Lindgren

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230907055441.19476-1-tony@atomide.com \
    --to=tony@atomide.com \
    --cc=d-gole@ti.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=j-keerthy@ti.com \
    --cc=khilman@baylibre.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=nm@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.