* [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-08-31 18:18 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-08-31 18:18 UTC (permalink / raw) To: linux-arm-kernel Cc: Marek Vasut, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, Shawn Guo, devicetree Describe VDD_ARM (BUCK2) run and standby voltage in DT. Signed-off-by: Marek Vasut <marex@denx.de> --- Cc: Conor Dooley <conor+dt@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org --- arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts index 13674dc64be9d..d98a040860a48 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ }; buck2: BUCK2 { /* VDD_ARM */ + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1000000>; regulator-ramp-delay = <3125>; -- 2.40.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-08-31 18:18 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-08-31 18:18 UTC (permalink / raw) To: linux-arm-kernel Cc: Marek Vasut, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, Shawn Guo, devicetree Describe VDD_ARM (BUCK2) run and standby voltage in DT. Signed-off-by: Marek Vasut <marex@denx.de> --- Cc: Conor Dooley <conor+dt@kernel.org> Cc: Fabio Estevam <festevam@gmail.com> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org --- arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts index 13674dc64be9d..d98a040860a48 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ }; buck2: BUCK2 { /* VDD_ARM */ + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1000000>; regulator-ramp-delay = <3125>; -- 2.40.1 ^ permalink raw reply related [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-08-31 18:18 ` Marek Vasut @ 2023-09-24 14:21 ` Shawn Guo -1 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-09-24 14:21 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > Signed-off-by: Marek Vasut <marex@denx.de> > --- > Cc: Conor Dooley <conor+dt@kernel.org> > Cc: Fabio Estevam <festevam@gmail.com> > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > Cc: Magnus Damm <magnus.damm@gmail.com> > Cc: Marek Vasut <marex@denx.de> > Cc: NXP Linux Team <linux-imx@nxp.com> > Cc: Peng Fan <peng.fan@nxp.com> > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > Cc: Rob Herring <robh+dt@kernel.org> > Cc: Sascha Hauer <s.hauer@pengutronix.de> > Cc: Shawn Guo <shawnguo@kernel.org> > Cc: devicetree@vger.kernel.org > Cc: linux-arm-kernel@lists.infradead.org > --- > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > 1 file changed, 2 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > index 13674dc64be9d..d98a040860a48 100644 > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > }; > > buck2: BUCK2 { /* VDD_ARM */ > + nxp,dvs-run-voltage = <950000>; > + nxp,dvs-standby-voltage = <850000>; Buck2 is not turned off in DSM on i.MX8MP? Shawn > regulator-min-microvolt = <850000>; > regulator-max-microvolt = <1000000>; > regulator-ramp-delay = <3125>; > -- > 2.40.1 > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-09-24 14:21 ` Shawn Guo 0 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-09-24 14:21 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > Signed-off-by: Marek Vasut <marex@denx.de> > --- > Cc: Conor Dooley <conor+dt@kernel.org> > Cc: Fabio Estevam <festevam@gmail.com> > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > Cc: Magnus Damm <magnus.damm@gmail.com> > Cc: Marek Vasut <marex@denx.de> > Cc: NXP Linux Team <linux-imx@nxp.com> > Cc: Peng Fan <peng.fan@nxp.com> > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > Cc: Rob Herring <robh+dt@kernel.org> > Cc: Sascha Hauer <s.hauer@pengutronix.de> > Cc: Shawn Guo <shawnguo@kernel.org> > Cc: devicetree@vger.kernel.org > Cc: linux-arm-kernel@lists.infradead.org > --- > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > 1 file changed, 2 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > index 13674dc64be9d..d98a040860a48 100644 > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > }; > > buck2: BUCK2 { /* VDD_ARM */ > + nxp,dvs-run-voltage = <950000>; > + nxp,dvs-standby-voltage = <850000>; Buck2 is not turned off in DSM on i.MX8MP? Shawn > regulator-min-microvolt = <850000>; > regulator-max-microvolt = <1000000>; > regulator-ramp-delay = <3125>; > -- > 2.40.1 > ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-09-24 14:21 ` Shawn Guo @ 2023-10-08 18:37 ` Marek Vasut -1 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-10-08 18:37 UTC (permalink / raw) To: Shawn Guo Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On 9/24/23 16:21, Shawn Guo wrote: > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: >> Describe VDD_ARM (BUCK2) run and standby voltage in DT. >> >> Signed-off-by: Marek Vasut <marex@denx.de> >> --- >> Cc: Conor Dooley <conor+dt@kernel.org> >> Cc: Fabio Estevam <festevam@gmail.com> >> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> >> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> >> Cc: Magnus Damm <magnus.damm@gmail.com> >> Cc: Marek Vasut <marex@denx.de> >> Cc: NXP Linux Team <linux-imx@nxp.com> >> Cc: Peng Fan <peng.fan@nxp.com> >> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> >> Cc: Rob Herring <robh+dt@kernel.org> >> Cc: Sascha Hauer <s.hauer@pengutronix.de> >> Cc: Shawn Guo <shawnguo@kernel.org> >> Cc: devicetree@vger.kernel.org >> Cc: linux-arm-kernel@lists.infradead.org >> --- >> arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ >> 1 file changed, 2 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >> index 13674dc64be9d..d98a040860a48 100644 >> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >> @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ >> }; >> >> buck2: BUCK2 { /* VDD_ARM */ >> + nxp,dvs-run-voltage = <950000>; >> + nxp,dvs-standby-voltage = <850000>; > > Buck2 is not turned off in DSM on i.MX8MP? It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-08 18:37 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-10-08 18:37 UTC (permalink / raw) To: Shawn Guo Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On 9/24/23 16:21, Shawn Guo wrote: > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: >> Describe VDD_ARM (BUCK2) run and standby voltage in DT. >> >> Signed-off-by: Marek Vasut <marex@denx.de> >> --- >> Cc: Conor Dooley <conor+dt@kernel.org> >> Cc: Fabio Estevam <festevam@gmail.com> >> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> >> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> >> Cc: Magnus Damm <magnus.damm@gmail.com> >> Cc: Marek Vasut <marex@denx.de> >> Cc: NXP Linux Team <linux-imx@nxp.com> >> Cc: Peng Fan <peng.fan@nxp.com> >> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> >> Cc: Rob Herring <robh+dt@kernel.org> >> Cc: Sascha Hauer <s.hauer@pengutronix.de> >> Cc: Shawn Guo <shawnguo@kernel.org> >> Cc: devicetree@vger.kernel.org >> Cc: linux-arm-kernel@lists.infradead.org >> --- >> arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ >> 1 file changed, 2 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >> index 13674dc64be9d..d98a040860a48 100644 >> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >> @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ >> }; >> >> buck2: BUCK2 { /* VDD_ARM */ >> + nxp,dvs-run-voltage = <950000>; >> + nxp,dvs-standby-voltage = <850000>; > > Buck2 is not turned off in DSM on i.MX8MP? It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-10-08 18:37 ` Marek Vasut @ 2023-10-09 12:36 ` Shawn Guo -1 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-09 12:36 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: > On 9/24/23 16:21, Shawn Guo wrote: > > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > > > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > > --- > > > Cc: Conor Dooley <conor+dt@kernel.org> > > > Cc: Fabio Estevam <festevam@gmail.com> > > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > > > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > > > Cc: Magnus Damm <magnus.damm@gmail.com> > > > Cc: Marek Vasut <marex@denx.de> > > > Cc: NXP Linux Team <linux-imx@nxp.com> > > > Cc: Peng Fan <peng.fan@nxp.com> > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > > > Cc: Rob Herring <robh+dt@kernel.org> > > > Cc: Sascha Hauer <s.hauer@pengutronix.de> > > > Cc: Shawn Guo <shawnguo@kernel.org> > > > Cc: devicetree@vger.kernel.org > > > Cc: linux-arm-kernel@lists.infradead.org > > > --- > > > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > > > 1 file changed, 2 insertions(+) > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > index 13674dc64be9d..d98a040860a48 100644 > > > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > > > }; > > > buck2: BUCK2 { /* VDD_ARM */ > > > + nxp,dvs-run-voltage = <950000>; > > > + nxp,dvs-standby-voltage = <850000>; > > > > Buck2 is not turned off in DSM on i.MX8MP? > > It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC is in STANDBY mode. My understanding is that the SoC will be in SUSPEND state while PMIC is in STANDBY mode. Is it possible that the SoC in IDLE/RUN while PMIC is in STANDBY mode at all? Shawn _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-09 12:36 ` Shawn Guo 0 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-09 12:36 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: > On 9/24/23 16:21, Shawn Guo wrote: > > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > > > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > > --- > > > Cc: Conor Dooley <conor+dt@kernel.org> > > > Cc: Fabio Estevam <festevam@gmail.com> > > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > > > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > > > Cc: Magnus Damm <magnus.damm@gmail.com> > > > Cc: Marek Vasut <marex@denx.de> > > > Cc: NXP Linux Team <linux-imx@nxp.com> > > > Cc: Peng Fan <peng.fan@nxp.com> > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > > > Cc: Rob Herring <robh+dt@kernel.org> > > > Cc: Sascha Hauer <s.hauer@pengutronix.de> > > > Cc: Shawn Guo <shawnguo@kernel.org> > > > Cc: devicetree@vger.kernel.org > > > Cc: linux-arm-kernel@lists.infradead.org > > > --- > > > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > > > 1 file changed, 2 insertions(+) > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > index 13674dc64be9d..d98a040860a48 100644 > > > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > > > }; > > > buck2: BUCK2 { /* VDD_ARM */ > > > + nxp,dvs-run-voltage = <950000>; > > > + nxp,dvs-standby-voltage = <850000>; > > > > Buck2 is not turned off in DSM on i.MX8MP? > > It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC is in STANDBY mode. My understanding is that the SoC will be in SUSPEND state while PMIC is in STANDBY mode. Is it possible that the SoC in IDLE/RUN while PMIC is in STANDBY mode at all? Shawn ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-10-09 12:36 ` Shawn Guo @ 2023-10-09 14:03 ` Marek Vasut -1 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-10-09 14:03 UTC (permalink / raw) To: Shawn Guo Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On 10/9/23 14:36, Shawn Guo wrote: > On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: >> On 9/24/23 16:21, Shawn Guo wrote: >>> On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: >>>> Describe VDD_ARM (BUCK2) run and standby voltage in DT. >>>> >>>> Signed-off-by: Marek Vasut <marex@denx.de> >>>> --- >>>> Cc: Conor Dooley <conor+dt@kernel.org> >>>> Cc: Fabio Estevam <festevam@gmail.com> >>>> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> >>>> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >>>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> >>>> Cc: Magnus Damm <magnus.damm@gmail.com> >>>> Cc: Marek Vasut <marex@denx.de> >>>> Cc: NXP Linux Team <linux-imx@nxp.com> >>>> Cc: Peng Fan <peng.fan@nxp.com> >>>> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> >>>> Cc: Rob Herring <robh+dt@kernel.org> >>>> Cc: Sascha Hauer <s.hauer@pengutronix.de> >>>> Cc: Shawn Guo <shawnguo@kernel.org> >>>> Cc: devicetree@vger.kernel.org >>>> Cc: linux-arm-kernel@lists.infradead.org >>>> --- >>>> arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ >>>> 1 file changed, 2 insertions(+) >>>> >>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>> index 13674dc64be9d..d98a040860a48 100644 >>>> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>> @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ >>>> }; >>>> buck2: BUCK2 { /* VDD_ARM */ >>>> + nxp,dvs-run-voltage = <950000>; >>>> + nxp,dvs-standby-voltage = <850000>; >>> >>> Buck2 is not turned off in DSM on i.MX8MP? >> >> It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . > > Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC > is in STANDBY mode. My understanding is that the SoC will be in SUSPEND > state while PMIC is in STANDBY mode. I agree > Is it possible that the SoC in > IDLE/RUN while PMIC is in STANDBY mode at all? No, I don't think so, but there's still the PMIC part: https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf 7.3.7 STANDBY mode " PCA9450 transitions to STANDBY mode from RUN mode when both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 and BUCK3 output voltage is set to BUCK1OUT_DVS1 and BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit in each BUCKx_CTRL register is configured to 1. " Specifically " BUCK2 are turned off when DVS_CTRL bit in each BUCKx_CTRL register is configured to 1. " 8.2.19 0x13 BUCK2CTRL " 4 DVS_CTRL DVS Control configuration 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of PMIC_STBY_REQ 1b = DVS control through PMIC_STBY_REQ " Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, the BUCK2 will stay powered on even in STANDBY/SUSPEND. _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-09 14:03 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-10-09 14:03 UTC (permalink / raw) To: Shawn Guo Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On 10/9/23 14:36, Shawn Guo wrote: > On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: >> On 9/24/23 16:21, Shawn Guo wrote: >>> On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: >>>> Describe VDD_ARM (BUCK2) run and standby voltage in DT. >>>> >>>> Signed-off-by: Marek Vasut <marex@denx.de> >>>> --- >>>> Cc: Conor Dooley <conor+dt@kernel.org> >>>> Cc: Fabio Estevam <festevam@gmail.com> >>>> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> >>>> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >>>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> >>>> Cc: Magnus Damm <magnus.damm@gmail.com> >>>> Cc: Marek Vasut <marex@denx.de> >>>> Cc: NXP Linux Team <linux-imx@nxp.com> >>>> Cc: Peng Fan <peng.fan@nxp.com> >>>> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> >>>> Cc: Rob Herring <robh+dt@kernel.org> >>>> Cc: Sascha Hauer <s.hauer@pengutronix.de> >>>> Cc: Shawn Guo <shawnguo@kernel.org> >>>> Cc: devicetree@vger.kernel.org >>>> Cc: linux-arm-kernel@lists.infradead.org >>>> --- >>>> arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ >>>> 1 file changed, 2 insertions(+) >>>> >>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>> index 13674dc64be9d..d98a040860a48 100644 >>>> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>> @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ >>>> }; >>>> buck2: BUCK2 { /* VDD_ARM */ >>>> + nxp,dvs-run-voltage = <950000>; >>>> + nxp,dvs-standby-voltage = <850000>; >>> >>> Buck2 is not turned off in DSM on i.MX8MP? >> >> It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . > > Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC > is in STANDBY mode. My understanding is that the SoC will be in SUSPEND > state while PMIC is in STANDBY mode. I agree > Is it possible that the SoC in > IDLE/RUN while PMIC is in STANDBY mode at all? No, I don't think so, but there's still the PMIC part: https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf 7.3.7 STANDBY mode " PCA9450 transitions to STANDBY mode from RUN mode when both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 and BUCK3 output voltage is set to BUCK1OUT_DVS1 and BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit in each BUCKx_CTRL register is configured to 1. " Specifically " BUCK2 are turned off when DVS_CTRL bit in each BUCKx_CTRL register is configured to 1. " 8.2.19 0x13 BUCK2CTRL " 4 DVS_CTRL DVS Control configuration 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of PMIC_STBY_REQ 1b = DVS control through PMIC_STBY_REQ " Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, the BUCK2 will stay powered on even in STANDBY/SUSPEND. ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-10-09 14:03 ` Marek Vasut @ 2023-10-10 0:58 ` Shawn Guo -1 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-10 0:58 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: > On 10/9/23 14:36, Shawn Guo wrote: > > On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: > > > On 9/24/23 16:21, Shawn Guo wrote: > > > > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > > > > > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > > > > > > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > > > > --- > > > > > Cc: Conor Dooley <conor+dt@kernel.org> > > > > > Cc: Fabio Estevam <festevam@gmail.com> > > > > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > > > > > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > > > > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > > > > > Cc: Magnus Damm <magnus.damm@gmail.com> > > > > > Cc: Marek Vasut <marex@denx.de> > > > > > Cc: NXP Linux Team <linux-imx@nxp.com> > > > > > Cc: Peng Fan <peng.fan@nxp.com> > > > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > > > > > Cc: Rob Herring <robh+dt@kernel.org> > > > > > Cc: Sascha Hauer <s.hauer@pengutronix.de> > > > > > Cc: Shawn Guo <shawnguo@kernel.org> > > > > > Cc: devicetree@vger.kernel.org > > > > > Cc: linux-arm-kernel@lists.infradead.org > > > > > --- > > > > > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > > > > > 1 file changed, 2 insertions(+) > > > > > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > index 13674dc64be9d..d98a040860a48 100644 > > > > > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > > > > > }; > > > > > buck2: BUCK2 { /* VDD_ARM */ > > > > > + nxp,dvs-run-voltage = <950000>; > > > > > + nxp,dvs-standby-voltage = <850000>; > > > > > > > > Buck2 is not turned off in DSM on i.MX8MP? > > > > > > It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . > > > > Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC > > is in STANDBY mode. My understanding is that the SoC will be in SUSPEND > > state while PMIC is in STANDBY mode. > > I agree > > > Is it possible that the SoC in > > IDLE/RUN while PMIC is in STANDBY mode at all? > > No, I don't think so, but there's still the PMIC part: > > https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf > > 7.3.7 STANDBY mode > " > PCA9450 transitions to STANDBY mode from RUN mode when > both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 > and BUCK3 output voltage is set to BUCK1OUT_DVS1 and > BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit > in each BUCKx_CTRL register is configured to 1. > " > > Specifically > " > BUCK2 are turned off when DVS_CTRL bit in each > BUCKx_CTRL register is configured to 1. > " > > 8.2.19 0x13 BUCK2CTRL > " > 4 > DVS_CTRL > DVS Control configuration > 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of > PMIC_STBY_REQ > 1b = DVS control through PMIC_STBY_REQ > " > > Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, > the BUCK2 will stay powered on even in STANDBY/SUSPEND. Hmm, isn't B2_ENMODE controlling on/off of BUCK2? BUCK2 enable mode 00b = OFF 01b = ON by PMIC_ON_REQ = H 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) 11b = Always ON So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ goes high, right? Shawn _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-10 0:58 ` Shawn Guo 0 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-10 0:58 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: > On 10/9/23 14:36, Shawn Guo wrote: > > On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: > > > On 9/24/23 16:21, Shawn Guo wrote: > > > > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > > > > > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > > > > > > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > > > > --- > > > > > Cc: Conor Dooley <conor+dt@kernel.org> > > > > > Cc: Fabio Estevam <festevam@gmail.com> > > > > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > > > > > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > > > > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > > > > > Cc: Magnus Damm <magnus.damm@gmail.com> > > > > > Cc: Marek Vasut <marex@denx.de> > > > > > Cc: NXP Linux Team <linux-imx@nxp.com> > > > > > Cc: Peng Fan <peng.fan@nxp.com> > > > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > > > > > Cc: Rob Herring <robh+dt@kernel.org> > > > > > Cc: Sascha Hauer <s.hauer@pengutronix.de> > > > > > Cc: Shawn Guo <shawnguo@kernel.org> > > > > > Cc: devicetree@vger.kernel.org > > > > > Cc: linux-arm-kernel@lists.infradead.org > > > > > --- > > > > > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > > > > > 1 file changed, 2 insertions(+) > > > > > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > index 13674dc64be9d..d98a040860a48 100644 > > > > > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > > > > > }; > > > > > buck2: BUCK2 { /* VDD_ARM */ > > > > > + nxp,dvs-run-voltage = <950000>; > > > > > + nxp,dvs-standby-voltage = <850000>; > > > > > > > > Buck2 is not turned off in DSM on i.MX8MP? > > > > > > It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . > > > > Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC > > is in STANDBY mode. My understanding is that the SoC will be in SUSPEND > > state while PMIC is in STANDBY mode. > > I agree > > > Is it possible that the SoC in > > IDLE/RUN while PMIC is in STANDBY mode at all? > > No, I don't think so, but there's still the PMIC part: > > https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf > > 7.3.7 STANDBY mode > " > PCA9450 transitions to STANDBY mode from RUN mode when > both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 > and BUCK3 output voltage is set to BUCK1OUT_DVS1 and > BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit > in each BUCKx_CTRL register is configured to 1. > " > > Specifically > " > BUCK2 are turned off when DVS_CTRL bit in each > BUCKx_CTRL register is configured to 1. > " > > 8.2.19 0x13 BUCK2CTRL > " > 4 > DVS_CTRL > DVS Control configuration > 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of > PMIC_STBY_REQ > 1b = DVS control through PMIC_STBY_REQ > " > > Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, > the BUCK2 will stay powered on even in STANDBY/SUSPEND. Hmm, isn't B2_ENMODE controlling on/off of BUCK2? BUCK2 enable mode 00b = OFF 01b = ON by PMIC_ON_REQ = H 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) 11b = Always ON So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ goes high, right? Shawn ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-10-10 0:58 ` Shawn Guo @ 2023-10-10 13:42 ` Marek Vasut -1 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-10-10 13:42 UTC (permalink / raw) To: Shawn Guo Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On 10/10/23 02:58, Shawn Guo wrote: > On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: >> On 10/9/23 14:36, Shawn Guo wrote: >>> On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: >>>> On 9/24/23 16:21, Shawn Guo wrote: >>>>> On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: >>>>>> Describe VDD_ARM (BUCK2) run and standby voltage in DT. >>>>>> >>>>>> Signed-off-by: Marek Vasut <marex@denx.de> >>>>>> --- >>>>>> Cc: Conor Dooley <conor+dt@kernel.org> >>>>>> Cc: Fabio Estevam <festevam@gmail.com> >>>>>> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> >>>>>> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >>>>>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> >>>>>> Cc: Magnus Damm <magnus.damm@gmail.com> >>>>>> Cc: Marek Vasut <marex@denx.de> >>>>>> Cc: NXP Linux Team <linux-imx@nxp.com> >>>>>> Cc: Peng Fan <peng.fan@nxp.com> >>>>>> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> >>>>>> Cc: Rob Herring <robh+dt@kernel.org> >>>>>> Cc: Sascha Hauer <s.hauer@pengutronix.de> >>>>>> Cc: Shawn Guo <shawnguo@kernel.org> >>>>>> Cc: devicetree@vger.kernel.org >>>>>> Cc: linux-arm-kernel@lists.infradead.org >>>>>> --- >>>>>> arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ >>>>>> 1 file changed, 2 insertions(+) >>>>>> >>>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>> index 13674dc64be9d..d98a040860a48 100644 >>>>>> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>> @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ >>>>>> }; >>>>>> buck2: BUCK2 { /* VDD_ARM */ >>>>>> + nxp,dvs-run-voltage = <950000>; >>>>>> + nxp,dvs-standby-voltage = <850000>; >>>>> >>>>> Buck2 is not turned off in DSM on i.MX8MP? >>>> >>>> It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . >>> >>> Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC >>> is in STANDBY mode. My understanding is that the SoC will be in SUSPEND >>> state while PMIC is in STANDBY mode. >> >> I agree >> >>> Is it possible that the SoC in >>> IDLE/RUN while PMIC is in STANDBY mode at all? >> >> No, I don't think so, but there's still the PMIC part: >> >> https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf >> >> 7.3.7 STANDBY mode >> " >> PCA9450 transitions to STANDBY mode from RUN mode when >> both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 >> and BUCK3 output voltage is set to BUCK1OUT_DVS1 and >> BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit >> in each BUCKx_CTRL register is configured to 1. >> " >> >> Specifically >> " >> BUCK2 are turned off when DVS_CTRL bit in each >> BUCKx_CTRL register is configured to 1. >> " >> >> 8.2.19 0x13 BUCK2CTRL >> " >> 4 >> DVS_CTRL >> DVS Control configuration >> 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of >> PMIC_STBY_REQ >> 1b = DVS control through PMIC_STBY_REQ >> " >> >> Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, >> the BUCK2 will stay powered on even in STANDBY/SUSPEND. > > Hmm, isn't B2_ENMODE controlling on/off of BUCK2? > > BUCK2 enable mode > 00b = OFF > 01b = ON by PMIC_ON_REQ = H > 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) > 11b = Always ON > > So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ > goes high, right? I think so. But since the buck2 in DVS behavior is user-configurable, and this can be configured by the bootloader, I would say that it is a good idea to keep the buck2 DVS value defined in the DT, rather than keep it undefined. Also note that this board is a development kit, so we just don't know what users might do with it. _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-10 13:42 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-10-10 13:42 UTC (permalink / raw) To: Shawn Guo Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On 10/10/23 02:58, Shawn Guo wrote: > On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: >> On 10/9/23 14:36, Shawn Guo wrote: >>> On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: >>>> On 9/24/23 16:21, Shawn Guo wrote: >>>>> On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: >>>>>> Describe VDD_ARM (BUCK2) run and standby voltage in DT. >>>>>> >>>>>> Signed-off-by: Marek Vasut <marex@denx.de> >>>>>> --- >>>>>> Cc: Conor Dooley <conor+dt@kernel.org> >>>>>> Cc: Fabio Estevam <festevam@gmail.com> >>>>>> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> >>>>>> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >>>>>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> >>>>>> Cc: Magnus Damm <magnus.damm@gmail.com> >>>>>> Cc: Marek Vasut <marex@denx.de> >>>>>> Cc: NXP Linux Team <linux-imx@nxp.com> >>>>>> Cc: Peng Fan <peng.fan@nxp.com> >>>>>> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> >>>>>> Cc: Rob Herring <robh+dt@kernel.org> >>>>>> Cc: Sascha Hauer <s.hauer@pengutronix.de> >>>>>> Cc: Shawn Guo <shawnguo@kernel.org> >>>>>> Cc: devicetree@vger.kernel.org >>>>>> Cc: linux-arm-kernel@lists.infradead.org >>>>>> --- >>>>>> arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ >>>>>> 1 file changed, 2 insertions(+) >>>>>> >>>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>> index 13674dc64be9d..d98a040860a48 100644 >>>>>> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>> @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ >>>>>> }; >>>>>> buck2: BUCK2 { /* VDD_ARM */ >>>>>> + nxp,dvs-run-voltage = <950000>; >>>>>> + nxp,dvs-standby-voltage = <850000>; >>>>> >>>>> Buck2 is not turned off in DSM on i.MX8MP? >>>> >>>> It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . >>> >>> Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC >>> is in STANDBY mode. My understanding is that the SoC will be in SUSPEND >>> state while PMIC is in STANDBY mode. >> >> I agree >> >>> Is it possible that the SoC in >>> IDLE/RUN while PMIC is in STANDBY mode at all? >> >> No, I don't think so, but there's still the PMIC part: >> >> https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf >> >> 7.3.7 STANDBY mode >> " >> PCA9450 transitions to STANDBY mode from RUN mode when >> both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 >> and BUCK3 output voltage is set to BUCK1OUT_DVS1 and >> BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit >> in each BUCKx_CTRL register is configured to 1. >> " >> >> Specifically >> " >> BUCK2 are turned off when DVS_CTRL bit in each >> BUCKx_CTRL register is configured to 1. >> " >> >> 8.2.19 0x13 BUCK2CTRL >> " >> 4 >> DVS_CTRL >> DVS Control configuration >> 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of >> PMIC_STBY_REQ >> 1b = DVS control through PMIC_STBY_REQ >> " >> >> Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, >> the BUCK2 will stay powered on even in STANDBY/SUSPEND. > > Hmm, isn't B2_ENMODE controlling on/off of BUCK2? > > BUCK2 enable mode > 00b = OFF > 01b = ON by PMIC_ON_REQ = H > 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) > 11b = Always ON > > So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ > goes high, right? I think so. But since the buck2 in DVS behavior is user-configurable, and this can be configured by the bootloader, I would say that it is a good idea to keep the buck2 DVS value defined in the DT, rather than keep it undefined. Also note that this board is a development kit, so we just don't know what users might do with it. ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-10-10 13:42 ` Marek Vasut @ 2023-10-11 2:12 ` Shawn Guo -1 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-11 2:12 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Tue, Oct 10, 2023 at 03:42:14PM +0200, Marek Vasut wrote: > On 10/10/23 02:58, Shawn Guo wrote: > > On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: > > > On 10/9/23 14:36, Shawn Guo wrote: > > > > On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: > > > > > On 9/24/23 16:21, Shawn Guo wrote: > > > > > > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > > > > > > > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > > > > > > > > > > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > > > > > > --- > > > > > > > Cc: Conor Dooley <conor+dt@kernel.org> > > > > > > > Cc: Fabio Estevam <festevam@gmail.com> > > > > > > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > > > > > > > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > > > > > > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > > > > > > > Cc: Magnus Damm <magnus.damm@gmail.com> > > > > > > > Cc: Marek Vasut <marex@denx.de> > > > > > > > Cc: NXP Linux Team <linux-imx@nxp.com> > > > > > > > Cc: Peng Fan <peng.fan@nxp.com> > > > > > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > > > > > > > Cc: Rob Herring <robh+dt@kernel.org> > > > > > > > Cc: Sascha Hauer <s.hauer@pengutronix.de> > > > > > > > Cc: Shawn Guo <shawnguo@kernel.org> > > > > > > > Cc: devicetree@vger.kernel.org > > > > > > > Cc: linux-arm-kernel@lists.infradead.org > > > > > > > --- > > > > > > > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > > > > > > > 1 file changed, 2 insertions(+) > > > > > > > > > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > index 13674dc64be9d..d98a040860a48 100644 > > > > > > > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > > > > > > > }; > > > > > > > buck2: BUCK2 { /* VDD_ARM */ > > > > > > > + nxp,dvs-run-voltage = <950000>; > > > > > > > + nxp,dvs-standby-voltage = <850000>; > > > > > > > > > > > > Buck2 is not turned off in DSM on i.MX8MP? > > > > > > > > > > It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . > > > > > > > > Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC > > > > is in STANDBY mode. My understanding is that the SoC will be in SUSPEND > > > > state while PMIC is in STANDBY mode. > > > > > > I agree > > > > > > > Is it possible that the SoC in > > > > IDLE/RUN while PMIC is in STANDBY mode at all? > > > > > > No, I don't think so, but there's still the PMIC part: > > > > > > https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf > > > > > > 7.3.7 STANDBY mode > > > " > > > PCA9450 transitions to STANDBY mode from RUN mode when > > > both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 > > > and BUCK3 output voltage is set to BUCK1OUT_DVS1 and > > > BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit > > > in each BUCKx_CTRL register is configured to 1. > > > " > > > > > > Specifically > > > " > > > BUCK2 are turned off when DVS_CTRL bit in each > > > BUCKx_CTRL register is configured to 1. > > > " > > > > > > 8.2.19 0x13 BUCK2CTRL > > > " > > > 4 > > > DVS_CTRL > > > DVS Control configuration > > > 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of > > > PMIC_STBY_REQ > > > 1b = DVS control through PMIC_STBY_REQ > > > " > > > > > > Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, > > > the BUCK2 will stay powered on even in STANDBY/SUSPEND. > > > > Hmm, isn't B2_ENMODE controlling on/off of BUCK2? > > > > BUCK2 enable mode > > 00b = OFF > > 01b = ON by PMIC_ON_REQ = H > > 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) > > 11b = Always ON > > > > So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ > > goes high, right? > > I think so. > > But since the buck2 in DVS behavior is user-configurable, and this can be > configured by the bootloader, I would say that it is a good idea to keep the > buck2 DVS value defined in the DT, rather than keep it undefined. > > Also note that this board is a development kit, so we just don't know what > users might do with it. Honestly, I just do not see any reason why one would change the most power efficient default configuration to something consuming much more power. Also, even if DVS control is enabled, 0.85 V is already the target voltage for STANDBY mode by default. Bottom line is that we should have some comment on this change, because it makes eDM SBC so unique among all those PCA9450 based boards and makes people like me wonder why eDM SBC board needs this setting. Shawn _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-11 2:12 ` Shawn Guo 0 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-11 2:12 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Tue, Oct 10, 2023 at 03:42:14PM +0200, Marek Vasut wrote: > On 10/10/23 02:58, Shawn Guo wrote: > > On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: > > > On 10/9/23 14:36, Shawn Guo wrote: > > > > On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: > > > > > On 9/24/23 16:21, Shawn Guo wrote: > > > > > > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > > > > > > > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > > > > > > > > > > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > > > > > > --- > > > > > > > Cc: Conor Dooley <conor+dt@kernel.org> > > > > > > > Cc: Fabio Estevam <festevam@gmail.com> > > > > > > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > > > > > > > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > > > > > > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > > > > > > > Cc: Magnus Damm <magnus.damm@gmail.com> > > > > > > > Cc: Marek Vasut <marex@denx.de> > > > > > > > Cc: NXP Linux Team <linux-imx@nxp.com> > > > > > > > Cc: Peng Fan <peng.fan@nxp.com> > > > > > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > > > > > > > Cc: Rob Herring <robh+dt@kernel.org> > > > > > > > Cc: Sascha Hauer <s.hauer@pengutronix.de> > > > > > > > Cc: Shawn Guo <shawnguo@kernel.org> > > > > > > > Cc: devicetree@vger.kernel.org > > > > > > > Cc: linux-arm-kernel@lists.infradead.org > > > > > > > --- > > > > > > > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > > > > > > > 1 file changed, 2 insertions(+) > > > > > > > > > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > index 13674dc64be9d..d98a040860a48 100644 > > > > > > > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > > > > > > > }; > > > > > > > buck2: BUCK2 { /* VDD_ARM */ > > > > > > > + nxp,dvs-run-voltage = <950000>; > > > > > > > + nxp,dvs-standby-voltage = <850000>; > > > > > > > > > > > > Buck2 is not turned off in DSM on i.MX8MP? > > > > > > > > > > It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . > > > > > > > > Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC > > > > is in STANDBY mode. My understanding is that the SoC will be in SUSPEND > > > > state while PMIC is in STANDBY mode. > > > > > > I agree > > > > > > > Is it possible that the SoC in > > > > IDLE/RUN while PMIC is in STANDBY mode at all? > > > > > > No, I don't think so, but there's still the PMIC part: > > > > > > https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf > > > > > > 7.3.7 STANDBY mode > > > " > > > PCA9450 transitions to STANDBY mode from RUN mode when > > > both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 > > > and BUCK3 output voltage is set to BUCK1OUT_DVS1 and > > > BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit > > > in each BUCKx_CTRL register is configured to 1. > > > " > > > > > > Specifically > > > " > > > BUCK2 are turned off when DVS_CTRL bit in each > > > BUCKx_CTRL register is configured to 1. > > > " > > > > > > 8.2.19 0x13 BUCK2CTRL > > > " > > > 4 > > > DVS_CTRL > > > DVS Control configuration > > > 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of > > > PMIC_STBY_REQ > > > 1b = DVS control through PMIC_STBY_REQ > > > " > > > > > > Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, > > > the BUCK2 will stay powered on even in STANDBY/SUSPEND. > > > > Hmm, isn't B2_ENMODE controlling on/off of BUCK2? > > > > BUCK2 enable mode > > 00b = OFF > > 01b = ON by PMIC_ON_REQ = H > > 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) > > 11b = Always ON > > > > So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ > > goes high, right? > > I think so. > > But since the buck2 in DVS behavior is user-configurable, and this can be > configured by the bootloader, I would say that it is a good idea to keep the > buck2 DVS value defined in the DT, rather than keep it undefined. > > Also note that this board is a development kit, so we just don't know what > users might do with it. Honestly, I just do not see any reason why one would change the most power efficient default configuration to something consuming much more power. Also, even if DVS control is enabled, 0.85 V is already the target voltage for STANDBY mode by default. Bottom line is that we should have some comment on this change, because it makes eDM SBC so unique among all those PCA9450 based boards and makes people like me wonder why eDM SBC board needs this setting. Shawn ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-10-11 2:12 ` Shawn Guo @ 2023-10-12 3:39 ` Marek Vasut -1 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-10-12 3:39 UTC (permalink / raw) To: Shawn Guo Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On 10/11/23 04:12, Shawn Guo wrote: > On Tue, Oct 10, 2023 at 03:42:14PM +0200, Marek Vasut wrote: >> On 10/10/23 02:58, Shawn Guo wrote: >>> On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: >>>> On 10/9/23 14:36, Shawn Guo wrote: >>>>> On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: >>>>>> On 9/24/23 16:21, Shawn Guo wrote: >>>>>>> On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: >>>>>>>> Describe VDD_ARM (BUCK2) run and standby voltage in DT. >>>>>>>> >>>>>>>> Signed-off-by: Marek Vasut <marex@denx.de> >>>>>>>> --- >>>>>>>> Cc: Conor Dooley <conor+dt@kernel.org> >>>>>>>> Cc: Fabio Estevam <festevam@gmail.com> >>>>>>>> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> >>>>>>>> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >>>>>>>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> >>>>>>>> Cc: Magnus Damm <magnus.damm@gmail.com> >>>>>>>> Cc: Marek Vasut <marex@denx.de> >>>>>>>> Cc: NXP Linux Team <linux-imx@nxp.com> >>>>>>>> Cc: Peng Fan <peng.fan@nxp.com> >>>>>>>> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> >>>>>>>> Cc: Rob Herring <robh+dt@kernel.org> >>>>>>>> Cc: Sascha Hauer <s.hauer@pengutronix.de> >>>>>>>> Cc: Shawn Guo <shawnguo@kernel.org> >>>>>>>> Cc: devicetree@vger.kernel.org >>>>>>>> Cc: linux-arm-kernel@lists.infradead.org >>>>>>>> --- >>>>>>>> arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ >>>>>>>> 1 file changed, 2 insertions(+) >>>>>>>> >>>>>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>>>> index 13674dc64be9d..d98a040860a48 100644 >>>>>>>> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>>>> @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ >>>>>>>> }; >>>>>>>> buck2: BUCK2 { /* VDD_ARM */ >>>>>>>> + nxp,dvs-run-voltage = <950000>; >>>>>>>> + nxp,dvs-standby-voltage = <850000>; >>>>>>> >>>>>>> Buck2 is not turned off in DSM on i.MX8MP? >>>>>> >>>>>> It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . >>>>> >>>>> Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC >>>>> is in STANDBY mode. My understanding is that the SoC will be in SUSPEND >>>>> state while PMIC is in STANDBY mode. >>>> >>>> I agree >>>> >>>>> Is it possible that the SoC in >>>>> IDLE/RUN while PMIC is in STANDBY mode at all? >>>> >>>> No, I don't think so, but there's still the PMIC part: >>>> >>>> https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf >>>> >>>> 7.3.7 STANDBY mode >>>> " >>>> PCA9450 transitions to STANDBY mode from RUN mode when >>>> both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 >>>> and BUCK3 output voltage is set to BUCK1OUT_DVS1 and >>>> BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit >>>> in each BUCKx_CTRL register is configured to 1. >>>> " >>>> >>>> Specifically >>>> " >>>> BUCK2 are turned off when DVS_CTRL bit in each >>>> BUCKx_CTRL register is configured to 1. >>>> " >>>> >>>> 8.2.19 0x13 BUCK2CTRL >>>> " >>>> 4 >>>> DVS_CTRL >>>> DVS Control configuration >>>> 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of >>>> PMIC_STBY_REQ >>>> 1b = DVS control through PMIC_STBY_REQ >>>> " >>>> >>>> Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, >>>> the BUCK2 will stay powered on even in STANDBY/SUSPEND. >>> >>> Hmm, isn't B2_ENMODE controlling on/off of BUCK2? >>> >>> BUCK2 enable mode >>> 00b = OFF >>> 01b = ON by PMIC_ON_REQ = H >>> 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) >>> 11b = Always ON >>> >>> So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ >>> goes high, right? >> >> I think so. >> >> But since the buck2 in DVS behavior is user-configurable, and this can be >> configured by the bootloader, I would say that it is a good idea to keep the >> buck2 DVS value defined in the DT, rather than keep it undefined. >> >> Also note that this board is a development kit, so we just don't know what >> users might do with it. > > Honestly, I just do not see any reason why one would change the most > power efficient default configuration to something consuming much more > power. > > Also, even if DVS control is enabled, 0.85 V is already the target > voltage for STANDBY mode by default. > > Bottom line is that we should have some comment on this change, because > it makes eDM SBC so unique among all those PCA9450 based boards and > makes people like me wonder why eDM SBC board needs this setting. This is definitely not unique, a lot of i.MX8MP boards configure both run and standby voltage for buck2 as well, even the NXP EVK does: next-20231011$ git grep -l dvs-standby-voltage arch/arm64/boot/dts/freescale/imx8mp* arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi arch/arm64/boot/dts/freescale/imx8mp-evk.dts arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi So, can this patch go in as-is or do you want additional comment in V2? _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-12 3:39 ` Marek Vasut 0 siblings, 0 replies; 22+ messages in thread From: Marek Vasut @ 2023-10-12 3:39 UTC (permalink / raw) To: Shawn Guo Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On 10/11/23 04:12, Shawn Guo wrote: > On Tue, Oct 10, 2023 at 03:42:14PM +0200, Marek Vasut wrote: >> On 10/10/23 02:58, Shawn Guo wrote: >>> On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: >>>> On 10/9/23 14:36, Shawn Guo wrote: >>>>> On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: >>>>>> On 9/24/23 16:21, Shawn Guo wrote: >>>>>>> On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: >>>>>>>> Describe VDD_ARM (BUCK2) run and standby voltage in DT. >>>>>>>> >>>>>>>> Signed-off-by: Marek Vasut <marex@denx.de> >>>>>>>> --- >>>>>>>> Cc: Conor Dooley <conor+dt@kernel.org> >>>>>>>> Cc: Fabio Estevam <festevam@gmail.com> >>>>>>>> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> >>>>>>>> Cc: Geert Uytterhoeven <geert+renesas@glider.be> >>>>>>>> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> >>>>>>>> Cc: Magnus Damm <magnus.damm@gmail.com> >>>>>>>> Cc: Marek Vasut <marex@denx.de> >>>>>>>> Cc: NXP Linux Team <linux-imx@nxp.com> >>>>>>>> Cc: Peng Fan <peng.fan@nxp.com> >>>>>>>> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> >>>>>>>> Cc: Rob Herring <robh+dt@kernel.org> >>>>>>>> Cc: Sascha Hauer <s.hauer@pengutronix.de> >>>>>>>> Cc: Shawn Guo <shawnguo@kernel.org> >>>>>>>> Cc: devicetree@vger.kernel.org >>>>>>>> Cc: linux-arm-kernel@lists.infradead.org >>>>>>>> --- >>>>>>>> arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ >>>>>>>> 1 file changed, 2 insertions(+) >>>>>>>> >>>>>>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>>>> index 13674dc64be9d..d98a040860a48 100644 >>>>>>>> --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts >>>>>>>> @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ >>>>>>>> }; >>>>>>>> buck2: BUCK2 { /* VDD_ARM */ >>>>>>>> + nxp,dvs-run-voltage = <950000>; >>>>>>>> + nxp,dvs-standby-voltage = <850000>; >>>>>>> >>>>>>> Buck2 is not turned off in DSM on i.MX8MP? >>>>>> >>>>>> It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . >>>>> >>>>> Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC >>>>> is in STANDBY mode. My understanding is that the SoC will be in SUSPEND >>>>> state while PMIC is in STANDBY mode. >>>> >>>> I agree >>>> >>>>> Is it possible that the SoC in >>>>> IDLE/RUN while PMIC is in STANDBY mode at all? >>>> >>>> No, I don't think so, but there's still the PMIC part: >>>> >>>> https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf >>>> >>>> 7.3.7 STANDBY mode >>>> " >>>> PCA9450 transitions to STANDBY mode from RUN mode when >>>> both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 >>>> and BUCK3 output voltage is set to BUCK1OUT_DVS1 and >>>> BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit >>>> in each BUCKx_CTRL register is configured to 1. >>>> " >>>> >>>> Specifically >>>> " >>>> BUCK2 are turned off when DVS_CTRL bit in each >>>> BUCKx_CTRL register is configured to 1. >>>> " >>>> >>>> 8.2.19 0x13 BUCK2CTRL >>>> " >>>> 4 >>>> DVS_CTRL >>>> DVS Control configuration >>>> 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of >>>> PMIC_STBY_REQ >>>> 1b = DVS control through PMIC_STBY_REQ >>>> " >>>> >>>> Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, >>>> the BUCK2 will stay powered on even in STANDBY/SUSPEND. >>> >>> Hmm, isn't B2_ENMODE controlling on/off of BUCK2? >>> >>> BUCK2 enable mode >>> 00b = OFF >>> 01b = ON by PMIC_ON_REQ = H >>> 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) >>> 11b = Always ON >>> >>> So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ >>> goes high, right? >> >> I think so. >> >> But since the buck2 in DVS behavior is user-configurable, and this can be >> configured by the bootloader, I would say that it is a good idea to keep the >> buck2 DVS value defined in the DT, rather than keep it undefined. >> >> Also note that this board is a development kit, so we just don't know what >> users might do with it. > > Honestly, I just do not see any reason why one would change the most > power efficient default configuration to something consuming much more > power. > > Also, even if DVS control is enabled, 0.85 V is already the target > voltage for STANDBY mode by default. > > Bottom line is that we should have some comment on this change, because > it makes eDM SBC so unique among all those PCA9450 based boards and > makes people like me wonder why eDM SBC board needs this setting. This is definitely not unique, a lot of i.MX8MP boards configure both run and standby voltage for buck2 as well, even the NXP EVK does: next-20231011$ git grep -l dvs-standby-voltage arch/arm64/boot/dts/freescale/imx8mp* arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi arch/arm64/boot/dts/freescale/imx8mp-evk.dts arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi So, can this patch go in as-is or do you want additional comment in V2? ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-10-12 3:39 ` Marek Vasut @ 2023-10-12 9:22 ` Shawn Guo -1 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-12 9:22 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Thu, Oct 12, 2023 at 05:39:08AM +0200, Marek Vasut wrote: > On 10/11/23 04:12, Shawn Guo wrote: > > On Tue, Oct 10, 2023 at 03:42:14PM +0200, Marek Vasut wrote: > > > On 10/10/23 02:58, Shawn Guo wrote: > > > > On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: > > > > > On 10/9/23 14:36, Shawn Guo wrote: > > > > > > On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: > > > > > > > On 9/24/23 16:21, Shawn Guo wrote: > > > > > > > > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > > > > > > > > > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > > > > > > > > > > > > > > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > > > > > > > > --- > > > > > > > > > Cc: Conor Dooley <conor+dt@kernel.org> > > > > > > > > > Cc: Fabio Estevam <festevam@gmail.com> > > > > > > > > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > > > > > > > > > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > > > > > > > > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > > > > > > > > > Cc: Magnus Damm <magnus.damm@gmail.com> > > > > > > > > > Cc: Marek Vasut <marex@denx.de> > > > > > > > > > Cc: NXP Linux Team <linux-imx@nxp.com> > > > > > > > > > Cc: Peng Fan <peng.fan@nxp.com> > > > > > > > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > > > > > > > > > Cc: Rob Herring <robh+dt@kernel.org> > > > > > > > > > Cc: Sascha Hauer <s.hauer@pengutronix.de> > > > > > > > > > Cc: Shawn Guo <shawnguo@kernel.org> > > > > > > > > > Cc: devicetree@vger.kernel.org > > > > > > > > > Cc: linux-arm-kernel@lists.infradead.org > > > > > > > > > --- > > > > > > > > > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > > > > > > > > > 1 file changed, 2 insertions(+) > > > > > > > > > > > > > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > > > index 13674dc64be9d..d98a040860a48 100644 > > > > > > > > > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > > > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > > > > > > > > > }; > > > > > > > > > buck2: BUCK2 { /* VDD_ARM */ > > > > > > > > > + nxp,dvs-run-voltage = <950000>; > > > > > > > > > + nxp,dvs-standby-voltage = <850000>; > > > > > > > > > > > > > > > > Buck2 is not turned off in DSM on i.MX8MP? > > > > > > > > > > > > > > It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . > > > > > > > > > > > > Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC > > > > > > is in STANDBY mode. My understanding is that the SoC will be in SUSPEND > > > > > > state while PMIC is in STANDBY mode. > > > > > > > > > > I agree > > > > > > > > > > > Is it possible that the SoC in > > > > > > IDLE/RUN while PMIC is in STANDBY mode at all? > > > > > > > > > > No, I don't think so, but there's still the PMIC part: > > > > > > > > > > https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf > > > > > > > > > > 7.3.7 STANDBY mode > > > > > " > > > > > PCA9450 transitions to STANDBY mode from RUN mode when > > > > > both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 > > > > > and BUCK3 output voltage is set to BUCK1OUT_DVS1 and > > > > > BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit > > > > > in each BUCKx_CTRL register is configured to 1. > > > > > " > > > > > > > > > > Specifically > > > > > " > > > > > BUCK2 are turned off when DVS_CTRL bit in each > > > > > BUCKx_CTRL register is configured to 1. > > > > > " > > > > > > > > > > 8.2.19 0x13 BUCK2CTRL > > > > > " > > > > > 4 > > > > > DVS_CTRL > > > > > DVS Control configuration > > > > > 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of > > > > > PMIC_STBY_REQ > > > > > 1b = DVS control through PMIC_STBY_REQ > > > > > " > > > > > > > > > > Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, > > > > > the BUCK2 will stay powered on even in STANDBY/SUSPEND. > > > > > > > > Hmm, isn't B2_ENMODE controlling on/off of BUCK2? > > > > > > > > BUCK2 enable mode > > > > 00b = OFF > > > > 01b = ON by PMIC_ON_REQ = H > > > > 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) > > > > 11b = Always ON > > > > > > > > So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ > > > > goes high, right? > > > > > > I think so. > > > > > > But since the buck2 in DVS behavior is user-configurable, and this can be > > > configured by the bootloader, I would say that it is a good idea to keep the > > > buck2 DVS value defined in the DT, rather than keep it undefined. > > > > > > Also note that this board is a development kit, so we just don't know what > > > users might do with it. > > > > Honestly, I just do not see any reason why one would change the most > > power efficient default configuration to something consuming much more > > power. > > > > Also, even if DVS control is enabled, 0.85 V is already the target > > voltage for STANDBY mode by default. > > > > Bottom line is that we should have some comment on this change, because > > it makes eDM SBC so unique among all those PCA9450 based boards and > > makes people like me wonder why eDM SBC board needs this setting. > > This is definitely not unique, a lot of i.MX8MP boards configure both run > and standby voltage for buck2 as well, even the NXP EVK does: > > next-20231011$ git grep -l dvs-standby-voltage > arch/arm64/boot/dts/freescale/imx8mp* > arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi > arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts > arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi > arch/arm64/boot/dts/freescale/imx8mp-evk.dts > arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi > arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi > arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi > arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts > arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi Ah, I should have done the grep myself. > So, can this patch go in as-is or do you want additional comment in V2? Ok, if board maintainers do not care about the cpu cycles wasted in pca9450 driver buck_set_dvs() function. I think I can live with this unnecessary DT setting. Shawn _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-12 9:22 ` Shawn Guo 0 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-12 9:22 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Thu, Oct 12, 2023 at 05:39:08AM +0200, Marek Vasut wrote: > On 10/11/23 04:12, Shawn Guo wrote: > > On Tue, Oct 10, 2023 at 03:42:14PM +0200, Marek Vasut wrote: > > > On 10/10/23 02:58, Shawn Guo wrote: > > > > On Mon, Oct 09, 2023 at 04:03:01PM +0200, Marek Vasut wrote: > > > > > On 10/9/23 14:36, Shawn Guo wrote: > > > > > > On Sun, Oct 08, 2023 at 08:37:34PM +0200, Marek Vasut wrote: > > > > > > > On 9/24/23 16:21, Shawn Guo wrote: > > > > > > > > On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > > > > > > > > > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > > > > > > > > > > > > > > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > > > > > > > > --- > > > > > > > > > Cc: Conor Dooley <conor+dt@kernel.org> > > > > > > > > > Cc: Fabio Estevam <festevam@gmail.com> > > > > > > > > > Cc: Frieder Schrempf <frieder.schrempf@kontron.de> > > > > > > > > > Cc: Geert Uytterhoeven <geert+renesas@glider.be> > > > > > > > > > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > > > > > > > > > Cc: Magnus Damm <magnus.damm@gmail.com> > > > > > > > > > Cc: Marek Vasut <marex@denx.de> > > > > > > > > > Cc: NXP Linux Team <linux-imx@nxp.com> > > > > > > > > > Cc: Peng Fan <peng.fan@nxp.com> > > > > > > > > > Cc: Pengutronix Kernel Team <kernel@pengutronix.de> > > > > > > > > > Cc: Rob Herring <robh+dt@kernel.org> > > > > > > > > > Cc: Sascha Hauer <s.hauer@pengutronix.de> > > > > > > > > > Cc: Shawn Guo <shawnguo@kernel.org> > > > > > > > > > Cc: devicetree@vger.kernel.org > > > > > > > > > Cc: linux-arm-kernel@lists.infradead.org > > > > > > > > > --- > > > > > > > > > arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts | 2 ++ > > > > > > > > > 1 file changed, 2 insertions(+) > > > > > > > > > > > > > > > > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > > > index 13674dc64be9d..d98a040860a48 100644 > > > > > > > > > --- a/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > > > +++ b/arch/arm64/boot/dts/freescale/imx8mp-data-modul-edm-sbc.dts > > > > > > > > > @@ -362,6 +362,8 @@ buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ > > > > > > > > > }; > > > > > > > > > buck2: BUCK2 { /* VDD_ARM */ > > > > > > > > > + nxp,dvs-run-voltage = <950000>; > > > > > > > > > + nxp,dvs-standby-voltage = <850000>; > > > > > > > > > > > > > > > > Buck2 is not turned off in DSM on i.MX8MP? > > > > > > > > > > > > > > It is turned off in SUSPEND/SNVS/OFF , not in IDLE/RUN . > > > > > > > > > > > > Right. But nxp,dvs-standby-voltage specifies the voltage when PMIC > > > > > > is in STANDBY mode. My understanding is that the SoC will be in SUSPEND > > > > > > state while PMIC is in STANDBY mode. > > > > > > > > > > I agree > > > > > > > > > > > Is it possible that the SoC in > > > > > > IDLE/RUN while PMIC is in STANDBY mode at all? > > > > > > > > > > No, I don't think so, but there's still the PMIC part: > > > > > > > > > > https://www.nxp.com/docs/en/data-sheet/PCA9450.pdf > > > > > > > > > > 7.3.7 STANDBY mode > > > > > " > > > > > PCA9450 transitions to STANDBY mode from RUN mode when > > > > > both PMIC_ON_REQ and PMIC_STBY_REQ are driven high. BUCK1 > > > > > and BUCK3 output voltage is set to BUCK1OUT_DVS1 and > > > > > BUCK3OUT_DVS1 and BUCK2 are turned off when DVS_CTRL bit > > > > > in each BUCKx_CTRL register is configured to 1. > > > > > " > > > > > > > > > > Specifically > > > > > " > > > > > BUCK2 are turned off when DVS_CTRL bit in each > > > > > BUCKx_CTRL register is configured to 1. > > > > > " > > > > > > > > > > 8.2.19 0x13 BUCK2CTRL > > > > > " > > > > > 4 > > > > > DVS_CTRL > > > > > DVS Control configuration > > > > > 0b = BUCK voltage is determined by BUCK2VOUT_DVS0 register regardless of > > > > > PMIC_STBY_REQ > > > > > 1b = DVS control through PMIC_STBY_REQ > > > > > " > > > > > > > > > > Notice that the reset-default is '0b' , so unless the PMIC is reconfigured, > > > > > the BUCK2 will stay powered on even in STANDBY/SUSPEND. > > > > > > > > Hmm, isn't B2_ENMODE controlling on/off of BUCK2? > > > > > > > > BUCK2 enable mode > > > > 00b = OFF > > > > 01b = ON by PMIC_ON_REQ = H > > > > 10b = ON by PMIC_ON_REQ = H && PMIC_STBY_REQ = L (default) > > > > 11b = Always ON > > > > > > > > So unless you reconfigure the field, BUCK2 will be off when PMIC_STBY_REQ > > > > goes high, right? > > > > > > I think so. > > > > > > But since the buck2 in DVS behavior is user-configurable, and this can be > > > configured by the bootloader, I would say that it is a good idea to keep the > > > buck2 DVS value defined in the DT, rather than keep it undefined. > > > > > > Also note that this board is a development kit, so we just don't know what > > > users might do with it. > > > > Honestly, I just do not see any reason why one would change the most > > power efficient default configuration to something consuming much more > > power. > > > > Also, even if DVS control is enabled, 0.85 V is already the target > > voltage for STANDBY mode by default. > > > > Bottom line is that we should have some comment on this change, because > > it makes eDM SBC so unique among all those PCA9450 based boards and > > makes people like me wonder why eDM SBC board needs this setting. > > This is definitely not unique, a lot of i.MX8MP boards configure both run > and standby voltage for buck2 as well, even the NXP EVK does: > > next-20231011$ git grep -l dvs-standby-voltage > arch/arm64/boot/dts/freescale/imx8mp* > arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi > arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts > arch/arm64/boot/dts/freescale/imx8mp-debix-som-a.dtsi > arch/arm64/boot/dts/freescale/imx8mp-evk.dts > arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi > arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi > arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi > arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts > arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi Ah, I should have done the grep myself. > So, can this patch go in as-is or do you want additional comment in V2? Ok, if board maintainers do not care about the cpu cycles wasted in pca9450 driver buck_set_dvs() function. I think I can live with this unnecessary DT setting. Shawn ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC 2023-08-31 18:18 ` Marek Vasut @ 2023-10-12 10:12 ` Shawn Guo -1 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-12 10:12 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > Signed-off-by: Marek Vasut <marex@denx.de> Applied, thanks! _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 22+ messages in thread
* Re: [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC @ 2023-10-12 10:12 ` Shawn Guo 0 siblings, 0 replies; 22+ messages in thread From: Shawn Guo @ 2023-10-12 10:12 UTC (permalink / raw) To: Marek Vasut Cc: linux-arm-kernel, Conor Dooley, Fabio Estevam, Frieder Schrempf, Geert Uytterhoeven, Krzysztof Kozlowski, Magnus Damm, NXP Linux Team, Peng Fan, Pengutronix Kernel Team, Rob Herring, Sascha Hauer, devicetree On Thu, Aug 31, 2023 at 08:18:50PM +0200, Marek Vasut wrote: > Describe VDD_ARM (BUCK2) run and standby voltage in DT. > > Signed-off-by: Marek Vasut <marex@denx.de> Applied, thanks! ^ permalink raw reply [flat|nested] 22+ messages in thread
end of thread, other threads:[~2023-10-12 10:13 UTC | newest] Thread overview: 22+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2023-08-31 18:18 [PATCH] arm64: dts: imx8mp: Describe VDD_ARM run and standby voltage for Data Modul i.MX8M Plus eDM SBC Marek Vasut 2023-08-31 18:18 ` Marek Vasut 2023-09-24 14:21 ` Shawn Guo 2023-09-24 14:21 ` Shawn Guo 2023-10-08 18:37 ` Marek Vasut 2023-10-08 18:37 ` Marek Vasut 2023-10-09 12:36 ` Shawn Guo 2023-10-09 12:36 ` Shawn Guo 2023-10-09 14:03 ` Marek Vasut 2023-10-09 14:03 ` Marek Vasut 2023-10-10 0:58 ` Shawn Guo 2023-10-10 0:58 ` Shawn Guo 2023-10-10 13:42 ` Marek Vasut 2023-10-10 13:42 ` Marek Vasut 2023-10-11 2:12 ` Shawn Guo 2023-10-11 2:12 ` Shawn Guo 2023-10-12 3:39 ` Marek Vasut 2023-10-12 3:39 ` Marek Vasut 2023-10-12 9:22 ` Shawn Guo 2023-10-12 9:22 ` Shawn Guo 2023-10-12 10:12 ` Shawn Guo 2023-10-12 10:12 ` Shawn Guo
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.