[PATCH v4 0/9] Enable cpufreq for IPQ5332 & IPQ9574

[PATCH v4 0/9] Enable cpufreq for IPQ5332 & IPQ9574

[Varadarajan Narayanan]

Depends On:
https://lore.kernel.org/lkml/20230913-gpll_cleanup-v2-6-c8ceb1a37680@quicinc.com/T/

This patch series aims to enable cpufreq for IPQ5332 and IPQ9574.
For IPQ5332, a minor enhancement to Stromer Plus ops and a safe
source switch is needed before cpu freq can be enabled.

These are also included in this series. Posting this as a single
series. Please let me know if this is not correct, will split in
the subsequent revisions.

Passed the following DT related validations
make W=1 ARCH=arm64 -j16 DT_CHECKER_FLAGS='-v -m' dt_binding_check DT_SCHEMA_FILES=qcom
make W=1 ARCH=arm64 -j16 CHECK_DTBS=y DT_SCHEMA_FILES=qcom dtbs_check

For IPQ5332:
~~~~~~~~~~~
	* This patch series introduces stromer plus ops which
	  builds on stromer ops and implements a different
	  set_rate and determine_rate.

	  A different set_rate is needed since stromer plus PLLs
	  do not support dynamic frequency scaling. To switch
	  between frequencies, we have to shut down the PLL,
	  configure the L and ALPHA values and turn on again. So
	  introduce the separate set of ops for Stromer Plus PLL.

	* Update ipq_pll_stromer_plus to use clk_alpha_pll_stromer_plus_ops
	  instead of clk_alpha_pll_stromer_ops.

	* Set 'l' value to a value that is supported on all SKUs.

	* Provide safe source switch for a53pll

	* Include IPQ5332 in cpufreq nvmem framework

	* Add OPP details to device tree

For IPQ9574:
~~~~~~~~~~~
	* Include IPQ9574 in cpufreq nvmem framework

	* Add OPP details to device tree

Removed 2 patches from V1 as they have been merged
	* dt-bindings: cpufreq: qcom-cpufreq-nvmem: document IPQ5332
	* dt-bindings: cpufreq: qcom-cpufreq-nvmem: document IPQ9574

v4:	Included a patch to fix 'kernel test robot' build error --
	https://lore.kernel.org/r/202310181650.g8THtfsm-lkp@intel.com/

Varadarajan Narayanan (9):
  clk: qcom: config IPQ_APSS_6018 should depend on QCOM_SMEM
  clk: qcom: clk-alpha-pll: introduce stromer plus ops
  clk: qcom: apss-ipq-pll: Use stromer plus ops for stromer plus pll
  clk: qcom: apss-ipq-pll: Fix 'l' value for ipq5332_pll_config
  clk: qcom: apss-ipq6018: ipq5332: add safe source switch for a53pll
  cpufreq: qti: Enable cpufreq for ipq53xx
  arm64: dts: qcom: ipq5332: populate the opp table based on the eFuse
  cpufreq: qti: Introduce cpufreq for ipq95xx
  arm64: dts: qcom: ipq9574: populate the opp table based on the eFuse

 arch/arm64/boot/dts/qcom/ipq5332.dtsi | 19 +++++++++--
 arch/arm64/boot/dts/qcom/ipq9574.dtsi | 21 +++++++++++-
 drivers/clk/qcom/Kconfig              |  1 +
 drivers/clk/qcom/apss-ipq-pll.c       |  4 +--
 drivers/clk/qcom/apss-ipq6018.c       | 58 +++++++++++++++++++++++++++++++-
 drivers/clk/qcom/clk-alpha-pll.c      | 63 +++++++++++++++++++++++++++++++++++
 drivers/clk/qcom/clk-alpha-pll.h      |  1 +
 drivers/cpufreq/cpufreq-dt-platdev.c  |  2 ++
 drivers/cpufreq/qcom-cpufreq-nvmem.c  | 16 +++++++++
 9 files changed, 178 insertions(+), 7 deletions(-)

-- 
2.7.4

[PATCH v4 1/9] clk: qcom: config IPQ_APSS_6018 should depend on QCOM_SMEM

[Varadarajan Narayanan]

The config IPQ_APSS_6018 should depend on QCOM_SMEM, to
avoid the following error.

Fixes: 5e77b4ef1b19 ("clk: qcom: Add ipq6018 apss clock controller")
Reported-by: kernel test robot <yujie.liu@intel.com>
Closes: https://lore.kernel.org/r/202310181650.g8THtfsm-lkp@intel.com/
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
 drivers/clk/qcom/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 3194c8b..ad1acd9 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -131,6 +131,7 @@ config IPQ_APSS_6018
 	tristate "IPQ APSS Clock Controller"
 	select IPQ_APSS_PLL
 	depends on QCOM_APCS_IPC || COMPILE_TEST
+	depends on QCOM_SMEM
 	help
 	  Support for APSS clock controller on IPQ platforms. The
 	  APSS clock controller manages the Mux and enable block that feeds the
-- 
2.7.4

Re: [PATCH v4 1/9] clk: qcom: config IPQ_APSS_6018 should depend on QCOM_SMEM

[Dmitry Baryshkov]

On Thu, 19 Oct 2023 at 11:42, Varadarajan Narayanan
<quic_varada@quicinc.com> wrote:
>
> The config IPQ_APSS_6018 should depend on QCOM_SMEM, to
> avoid the following error.

Which error?

>
> Fixes: 5e77b4ef1b19 ("clk: qcom: Add ipq6018 apss clock controller")
> Reported-by: kernel test robot <yujie.liu@intel.com>
> Closes: https://lore.kernel.org/r/202310181650.g8THtfsm-lkp@intel.com/
> Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
> ---
>  drivers/clk/qcom/Kconfig | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
> index 3194c8b..ad1acd9 100644
> --- a/drivers/clk/qcom/Kconfig
> +++ b/drivers/clk/qcom/Kconfig
> @@ -131,6 +131,7 @@ config IPQ_APSS_6018
>         tristate "IPQ APSS Clock Controller"
>         select IPQ_APSS_PLL
>         depends on QCOM_APCS_IPC || COMPILE_TEST
> +       depends on QCOM_SMEM
>         help
>           Support for APSS clock controller on IPQ platforms. The
>           APSS clock controller manages the Mux and enable block that feeds the
> --
> 2.7.4
>


-- 
With best wishes
Dmitry

Re: [PATCH v4 1/9] clk: qcom: config IPQ_APSS_6018 should depend on QCOM_SMEM

[Varadarajan Narayanan]

On Thu, Oct 19, 2023 at 04:12:25PM +0300, Dmitry Baryshkov wrote:
> On Thu, 19 Oct 2023 at 11:42, Varadarajan Narayanan
> <quic_varada@quicinc.com> wrote:
> >
> > The config IPQ_APSS_6018 should depend on QCOM_SMEM, to
> > avoid the following error.
>
> Which error?

Sorry. I assumed that it would refer to the info mentioned in the
'Reported-by' & 'Closes' tags.

Have included the error message in the commit log, addressed other
comments and posted v5. Kindly take a look.

Thanks
Varada

> > Fixes: 5e77b4ef1b19 ("clk: qcom: Add ipq6018 apss clock controller")
> > Reported-by: kernel test robot <yujie.liu@intel.com>
> > Closes: https://lore.kernel.org/r/202310181650.g8THtfsm-lkp@intel.com/
> > Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
> > ---
> >  drivers/clk/qcom/Kconfig | 1 +
> >  1 file changed, 1 insertion(+)
> >
> > diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
> > index 3194c8b..ad1acd9 100644
> > --- a/drivers/clk/qcom/Kconfig
> > +++ b/drivers/clk/qcom/Kconfig
> > @@ -131,6 +131,7 @@ config IPQ_APSS_6018
> >         tristate "IPQ APSS Clock Controller"
> >         select IPQ_APSS_PLL
> >         depends on QCOM_APCS_IPC || COMPILE_TEST
> > +       depends on QCOM_SMEM
> >         help
> >           Support for APSS clock controller on IPQ platforms. The
> >           APSS clock controller manages the Mux and enable block that feeds the
> > --
> > 2.7.4
> >
>
>
> --
> With best wishes
> Dmitry

[PATCH v4 2/9] clk: qcom: clk-alpha-pll: introduce stromer plus ops

[Varadarajan Narayanan]

Stromer plus APSS PLL does not support dynamic frequency scaling.
To switch between frequencies, we have to shut down the PLL,
configure the L and ALPHA values and turn on again. So introduce the
separate set of ops for Stromer Plus PLL.

Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v4:	Ensure PLL is enabled before re-enabling
v3:	Use prepare/unprepare instead of disable/enable in clk_alpha_pll_stromer_plus_ops
v2:	Use clk_alpha_pll_stromer_determine_rate, instead of adding new
	clk_alpha_pll_stromer_plus_determine_rate as the alpha pll width
	is same for both

	Fix review comments
		udelay(50) -> usleep_range(50, 60)
		Remove SoC-specific from print message
---
 drivers/clk/qcom/clk-alpha-pll.c | 63 ++++++++++++++++++++++++++++++++++++++++
 drivers/clk/qcom/clk-alpha-pll.h |  1 +
 2 files changed, 64 insertions(+)

diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 4edbf77..05898d2 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -2508,3 +2508,66 @@ const struct clk_ops clk_alpha_pll_stromer_ops = {
 	.set_rate = clk_alpha_pll_stromer_set_rate,
 };
 EXPORT_SYMBOL_GPL(clk_alpha_pll_stromer_ops);
+
+static int clk_alpha_pll_stromer_plus_set_rate(struct clk_hw *hw,
+					       unsigned long rate,
+					       unsigned long prate)
+{
+	struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+	u32 l, alpha_width = pll_alpha_width(pll);
+	int ret, pll_mode;
+	u64 a;
+
+	rate = alpha_pll_round_rate(rate, prate, &l, &a, alpha_width);
+
+	ret = regmap_read(pll->clkr.regmap, PLL_MODE(pll), &pll_mode);
+	if (ret)
+		return ret;
+
+	regmap_write(pll->clkr.regmap, PLL_MODE(pll), 0);
+
+	/* Delay of 2 output clock ticks required until output is disabled */
+	udelay(1);
+
+	regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
+
+	if (alpha_width > ALPHA_BITWIDTH)
+		a <<= alpha_width - ALPHA_BITWIDTH;
+
+	regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), a);
+	regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL_U(pll),
+					a >> ALPHA_BITWIDTH);
+
+	regmap_write(pll->clkr.regmap, PLL_MODE(pll), PLL_BYPASSNL);
+
+	/* Wait five micro seconds or more */
+	udelay(5);
+	regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_RESET_N,
+			   PLL_RESET_N);
+
+	/* The lock time should be less than 50 micro seconds worst case */
+	usleep_range(50, 60);
+
+	ret = wait_for_pll_enable_lock(pll);
+	if (ret) {
+		pr_err("Wait for PLL enable lock failed [%s] %d\n",
+		       clk_hw_get_name(hw), ret);
+		return ret;
+	}
+
+	if (pll_mode & PLL_OUTCTRL)
+		regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_OUTCTRL,
+				   PLL_OUTCTRL);
+
+	return 0;
+}
+
+const struct clk_ops clk_alpha_pll_stromer_plus_ops = {
+	.prepare = clk_alpha_pll_enable,
+	.unprepare = clk_alpha_pll_disable,
+	.is_enabled = clk_alpha_pll_is_enabled,
+	.recalc_rate = clk_alpha_pll_recalc_rate,
+	.determine_rate = clk_alpha_pll_stromer_determine_rate,
+	.set_rate = clk_alpha_pll_stromer_plus_set_rate,
+};
+EXPORT_SYMBOL_GPL(clk_alpha_pll_stromer_plus_ops);
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index 3b24a66..a1a75bb 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -152,6 +152,7 @@ extern const struct clk_ops clk_alpha_pll_postdiv_ops;
 extern const struct clk_ops clk_alpha_pll_huayra_ops;
 extern const struct clk_ops clk_alpha_pll_postdiv_ro_ops;
 extern const struct clk_ops clk_alpha_pll_stromer_ops;
+extern const struct clk_ops clk_alpha_pll_stromer_plus_ops;
 
 extern const struct clk_ops clk_alpha_pll_fabia_ops;
 extern const struct clk_ops clk_alpha_pll_fixed_fabia_ops;
-- 
2.7.4

Re: [PATCH v4 2/9] clk: qcom: clk-alpha-pll: introduce stromer plus ops

[Dmitry Baryshkov]

On Thu, 19 Oct 2023 at 11:42, Varadarajan Narayanan
<quic_varada@quicinc.com> wrote:
>
> Stromer plus APSS PLL does not support dynamic frequency scaling.
> To switch between frequencies, we have to shut down the PLL,
> configure the L and ALPHA values and turn on again. So introduce the
> separate set of ops for Stromer Plus PLL.
>
> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
> Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
> ---
> v4:     Ensure PLL is enabled before re-enabling
> v3:     Use prepare/unprepare instead of disable/enable in clk_alpha_pll_stromer_plus_ops
> v2:     Use clk_alpha_pll_stromer_determine_rate, instead of adding new
>         clk_alpha_pll_stromer_plus_determine_rate as the alpha pll width
>         is same for both
>
>         Fix review comments
>                 udelay(50) -> usleep_range(50, 60)
>                 Remove SoC-specific from print message
> ---
>  drivers/clk/qcom/clk-alpha-pll.c | 63 ++++++++++++++++++++++++++++++++++++++++
>  drivers/clk/qcom/clk-alpha-pll.h |  1 +
>  2 files changed, 64 insertions(+)

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry

[PATCH v4 3/9] clk: qcom: apss-ipq-pll: Use stromer plus ops for stromer plus pll

[Varadarajan Narayanan]

The set rate and determine rate operations are different between
Stromer and Stromer Plus PLLs. Since the programming sequence is
different, the PLLs dont get configured properly and random,
inexplicable crash/freeze is seen. Hence, use stromer plus ops
for ipq_pll_stromer_plus.

Acked-by: Stephen Boyd <sboyd@kernel.org>
Fixes: c7ef7fbb1ccf ("clk: qcom: apss-ipq-pll: add support for IPQ5332")
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v4:	Update commit log to include
		"What goes wrong if we don't have this patch?"
v2:	Add Fixes tag
---
 drivers/clk/qcom/apss-ipq-pll.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/qcom/apss-ipq-pll.c b/drivers/clk/qcom/apss-ipq-pll.c
index e170331..18c4ffe 100644
--- a/drivers/clk/qcom/apss-ipq-pll.c
+++ b/drivers/clk/qcom/apss-ipq-pll.c
@@ -68,7 +68,7 @@ static struct clk_alpha_pll ipq_pll_stromer_plus = {
 				.fw_name = "xo",
 			},
 			.num_parents = 1,
-			.ops = &clk_alpha_pll_stromer_ops,
+			.ops = &clk_alpha_pll_stromer_plus_ops,
 		},
 	},
 };
-- 
2.7.4

Re: [PATCH v4 3/9] clk: qcom: apss-ipq-pll: Use stromer plus ops for stromer plus pll

[Dmitry Baryshkov]

On Thu, 19 Oct 2023 at 11:42, Varadarajan Narayanan
<quic_varada@quicinc.com> wrote:
>
> The set rate and determine rate operations are different between
> Stromer and Stromer Plus PLLs. Since the programming sequence is
> different, the PLLs dont get configured properly and random,
> inexplicable crash/freeze is seen. Hence, use stromer plus ops
> for ipq_pll_stromer_plus.
>
> Acked-by: Stephen Boyd <sboyd@kernel.org>
> Fixes: c7ef7fbb1ccf ("clk: qcom: apss-ipq-pll: add support for IPQ5332")
> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
> Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
> ---
> v4:     Update commit log to include
>                 "What goes wrong if we don't have this patch?"
> v2:     Add Fixes tag
> ---
>  drivers/clk/qcom/apss-ipq-pll.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

-- 
With best wishes
Dmitry

[PATCH v4 4/9] clk: qcom: apss-ipq-pll: Fix 'l' value for ipq5332_pll_config

[Varadarajan Narayanan]

The earlier 'l' value of 0x3e is for 1.5GHz. Not all SKUs support
this frequency. Hence set it to 0x2d to get 1.1GHz which is
supported in all SKUs.

The frequency can still increase above this initial configuration
made here when the cpufreq driver picks a different OPP.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Fixes: c7ef7fbb1ccf ("clk: qcom: apss-ipq-pll: add support for IPQ5332")
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v4:	Update commit log to indicate that cpufreq could subsequently
	change the frequency based on the selected OPP
---
 drivers/clk/qcom/apss-ipq-pll.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/clk/qcom/apss-ipq-pll.c b/drivers/clk/qcom/apss-ipq-pll.c
index 18c4ffe..41279e5 100644
--- a/drivers/clk/qcom/apss-ipq-pll.c
+++ b/drivers/clk/qcom/apss-ipq-pll.c
@@ -74,7 +74,7 @@ static struct clk_alpha_pll ipq_pll_stromer_plus = {
 };
 
 static const struct alpha_pll_config ipq5332_pll_config = {
-	.l = 0x3e,
+	.l = 0x2d,
 	.config_ctl_val = 0x4001075b,
 	.config_ctl_hi_val = 0x304,
 	.main_output_mask = BIT(0),
-- 
2.7.4

[PATCH v4 5/9] clk: qcom: apss-ipq6018: ipq5332: add safe source switch for a53pll

[Varadarajan Narayanan]

Stromer Plus PLL found on IPQ53xx doesn't support dynamic
frequency scaling. To achieve the same, we need to park the APPS
PLL source to GPLL0, re configure the PLL and then switch the
source to APSS_PLL_EARLY.

To support this, register a clock notifier to get the PRE_RATE
and POST_RATE notification. Change the APSS PLL source to GPLL0
when PRE_RATE notification is received, then configure the PLL
and then change back the source to APSS_PLL_EARLY.

Additionally, not all SKUs of IPQ53xx support scaling. Hence,
do the above to the SKUs that support scaling.

Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v3:	devm_kzalloc for cpu_clk_notifier instead of global static
v2:	Handle ABORT_RATE_CHANGE
	Use local variable for apcs_alias0_clk_src.clkr.hw
	Use single line comment instead of multi line style
---
 drivers/clk/qcom/apss-ipq6018.c | 58 ++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 57 insertions(+), 1 deletion(-)

diff --git a/drivers/clk/qcom/apss-ipq6018.c b/drivers/clk/qcom/apss-ipq6018.c
index 4e13a08..db65b0d 100644
--- a/drivers/clk/qcom/apss-ipq6018.c
+++ b/drivers/clk/qcom/apss-ipq6018.c
@@ -9,8 +9,11 @@
 #include <linux/clk-provider.h>
 #include <linux/regmap.h>
 #include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/soc/qcom/smem.h>
 
 #include <dt-bindings/clock/qcom,apss-ipq.h>
+#include <dt-bindings/arm/qcom,ids.h>
 
 #include "common.h"
 #include "clk-regmap.h"
@@ -84,15 +87,68 @@ static const struct qcom_cc_desc apss_ipq6018_desc = {
 	.num_clks = ARRAY_SIZE(apss_ipq6018_clks),
 };
 
+static int cpu_clk_notifier_fn(struct notifier_block *nb, unsigned long action,
+				void *data)
+{
+	struct clk_hw *hw;
+	u8 index;
+	int err;
+
+	if (action == PRE_RATE_CHANGE)
+		index = P_GPLL0;
+	else if (action == POST_RATE_CHANGE || action == ABORT_RATE_CHANGE)
+		index = P_APSS_PLL_EARLY;
+	else
+		return NOTIFY_OK;
+
+	hw = &apcs_alias0_clk_src.clkr.hw;
+	err = clk_rcg2_mux_closest_ops.set_parent(hw, index);
+
+	return notifier_from_errno(err);
+}
+
 static int apss_ipq6018_probe(struct platform_device *pdev)
 {
+	struct notifier_block *cpu_clk_notifier;
 	struct regmap *regmap;
+	u32 soc_id;
+	int ret;
+
+	ret = qcom_smem_get_soc_id(&soc_id);
+	if (ret)
+		return ret;
 
 	regmap = dev_get_regmap(pdev->dev.parent, NULL);
 	if (!regmap)
 		return -ENODEV;
 
-	return qcom_cc_really_probe(pdev, &apss_ipq6018_desc, regmap);
+	ret = qcom_cc_really_probe(pdev, &apss_ipq6018_desc, regmap);
+	if (ret)
+		return ret;
+
+	switch (soc_id) {
+	/* Only below variants of IPQ53xx support scaling */
+	case QCOM_ID_IPQ5332:
+	case QCOM_ID_IPQ5322:
+	case QCOM_ID_IPQ5300:
+		cpu_clk_notifier = devm_kzalloc(&pdev->dev,
+						sizeof(*cpu_clk_notifier),
+						GFP_KERNEL);
+		if (!cpu_clk_notifier)
+			return -ENOMEM;
+
+		cpu_clk_notifier->notifier_call = cpu_clk_notifier_fn;
+
+		ret = clk_notifier_register(apcs_alias0_clk_src.clkr.hw.clk,
+					    cpu_clk_notifier);
+		if (ret)
+			return ret;
+		break;
+	default:
+		break;
+	}
+
+	return 0;
 }
 
 static struct platform_driver apss_ipq6018_driver = {
-- 
2.7.4

Re: [PATCH v4 5/9] clk: qcom: apss-ipq6018: ipq5332: add safe source switch for a53pll

[Dmitry Baryshkov]

On Thu, 19 Oct 2023 at 11:42, Varadarajan Narayanan
<quic_varada@quicinc.com> wrote:
>
> Stromer Plus PLL found on IPQ53xx doesn't support dynamic
> frequency scaling. To achieve the same, we need to park the APPS
> PLL source to GPLL0, re configure the PLL and then switch the
> source to APSS_PLL_EARLY.
>
> To support this, register a clock notifier to get the PRE_RATE
> and POST_RATE notification. Change the APSS PLL source to GPLL0
> when PRE_RATE notification is received, then configure the PLL
> and then change back the source to APSS_PLL_EARLY.
>
> Additionally, not all SKUs of IPQ53xx support scaling. Hence,
> do the above to the SKUs that support scaling.
>
> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
> Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
> ---
> v3:     devm_kzalloc for cpu_clk_notifier instead of global static
> v2:     Handle ABORT_RATE_CHANGE
>         Use local variable for apcs_alias0_clk_src.clkr.hw
>         Use single line comment instead of multi line style
> ---
>  drivers/clk/qcom/apss-ipq6018.c | 58 ++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 57 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/clk/qcom/apss-ipq6018.c b/drivers/clk/qcom/apss-ipq6018.c
> index 4e13a08..db65b0d 100644
> --- a/drivers/clk/qcom/apss-ipq6018.c
> +++ b/drivers/clk/qcom/apss-ipq6018.c
> @@ -9,8 +9,11 @@
>  #include <linux/clk-provider.h>
>  #include <linux/regmap.h>
>  #include <linux/module.h>
> +#include <linux/clk.h>
> +#include <linux/soc/qcom/smem.h>
>
>  #include <dt-bindings/clock/qcom,apss-ipq.h>
> +#include <dt-bindings/arm/qcom,ids.h>
>
>  #include "common.h"
>  #include "clk-regmap.h"
> @@ -84,15 +87,68 @@ static const struct qcom_cc_desc apss_ipq6018_desc = {
>         .num_clks = ARRAY_SIZE(apss_ipq6018_clks),
>  };
>
> +static int cpu_clk_notifier_fn(struct notifier_block *nb, unsigned long action,
> +                               void *data)
> +{
> +       struct clk_hw *hw;
> +       u8 index;
> +       int err;
> +
> +       if (action == PRE_RATE_CHANGE)
> +               index = P_GPLL0;
> +       else if (action == POST_RATE_CHANGE || action == ABORT_RATE_CHANGE)
> +               index = P_APSS_PLL_EARLY;
> +       else
> +               return NOTIFY_OK;
> +
> +       hw = &apcs_alias0_clk_src.clkr.hw;
> +       err = clk_rcg2_mux_closest_ops.set_parent(hw, index);
> +
> +       return notifier_from_errno(err);
> +}
> +
>  static int apss_ipq6018_probe(struct platform_device *pdev)
>  {
> +       struct notifier_block *cpu_clk_notifier;
>         struct regmap *regmap;
> +       u32 soc_id;
> +       int ret;
> +
> +       ret = qcom_smem_get_soc_id(&soc_id);
> +       if (ret)
> +               return ret;
>
>         regmap = dev_get_regmap(pdev->dev.parent, NULL);
>         if (!regmap)
>                 return -ENODEV;
>
> -       return qcom_cc_really_probe(pdev, &apss_ipq6018_desc, regmap);
> +       ret = qcom_cc_really_probe(pdev, &apss_ipq6018_desc, regmap);
> +       if (ret)
> +               return ret;
> +
> +       switch (soc_id) {
> +       /* Only below variants of IPQ53xx support scaling */
> +       case QCOM_ID_IPQ5332:
> +       case QCOM_ID_IPQ5322:
> +       case QCOM_ID_IPQ5300:
> +               cpu_clk_notifier = devm_kzalloc(&pdev->dev,
> +                                               sizeof(*cpu_clk_notifier),
> +                                               GFP_KERNEL);
> +               if (!cpu_clk_notifier)
> +                       return -ENOMEM;
> +
> +               cpu_clk_notifier->notifier_call = cpu_clk_notifier_fn;
> +
> +               ret = clk_notifier_register(apcs_alias0_clk_src.clkr.hw.clk,
> +                                           cpu_clk_notifier);

devm_clk_notifier_register sounds more future-proof.

Other than that:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

> +               if (ret)
> +                       return ret;
> +               break;
> +       default:
> +               break;
> +       }
> +
> +       return 0;
>  }
>
>  static struct platform_driver apss_ipq6018_driver = {
> --
> 2.7.4
>


-- 
With best wishes
Dmitry

[PATCH v4 6/9] cpufreq: qti: Enable cpufreq for ipq53xx

[Varadarajan Narayanan]

IPQ53xx have different OPPs available for the CPU based on
SoC variant. This can be determined through use of an eFuse
register present in the silicon.

Added support for ipq53xx on nvmem driver which helps to
determine OPPs at runtime based on the eFuse register which
has the CPU frequency limits. opp-supported-hw dt binding
can be used to indicate the available OPPs for each limit.

nvmem driver also creates the "cpufreq-dt" platform_device after
passing the version matching data to the OPP framework so that the
cpufreq-dt handles the actual cpufreq implementation.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v2:	Move IPQ53xx after APQ8096SG
---
 drivers/cpufreq/cpufreq-dt-platdev.c | 1 +
 drivers/cpufreq/qcom-cpufreq-nvmem.c | 8 ++++++++
 2 files changed, 9 insertions(+)

diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index 675da7f..f43e5cd 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -180,6 +180,7 @@ static const struct of_device_id blocklist[] __initconst = {
 	{ .compatible = "ti,am62a7", },
 	{ .compatible = "ti,am62p5", },
 
+	{ .compatible = "qcom,ipq5332", },
 	{ .compatible = "qcom,ipq8064", },
 	{ .compatible = "qcom,ipq8074", },
 	{ .compatible = "qcom,apq8064", },
diff --git a/drivers/cpufreq/qcom-cpufreq-nvmem.c b/drivers/cpufreq/qcom-cpufreq-nvmem.c
index 3fa1264..0014909 100644
--- a/drivers/cpufreq/qcom-cpufreq-nvmem.c
+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c
@@ -159,6 +159,13 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev,
 	case QCOM_ID_APQ8096SG:
 		drv->versions = 1 << ((unsigned int)(*speedbin) + 4);
 		break;
+	case QCOM_ID_IPQ5332:
+	case QCOM_ID_IPQ5322:
+	case QCOM_ID_IPQ5312:
+	case QCOM_ID_IPQ5302:
+	case QCOM_ID_IPQ5300:
+		drv->versions = 1 << (unsigned int)(*speedbin);
+		break;
 	default:
 		BUG();
 		break;
@@ -406,6 +413,7 @@ static const struct of_device_id qcom_cpufreq_match_list[] __initconst = {
 	{ .compatible = "qcom,apq8096", .data = &match_data_kryo },
 	{ .compatible = "qcom,msm8996", .data = &match_data_kryo },
 	{ .compatible = "qcom,qcs404", .data = &match_data_qcs404 },
+	{ .compatible = "qcom,ipq5332", .data = &match_data_kryo },
 	{ .compatible = "qcom,ipq8064", .data = &match_data_krait },
 	{ .compatible = "qcom,ipq8074", .data = &match_data_ipq8074 },
 	{ .compatible = "qcom,apq8064", .data = &match_data_krait },
-- 
2.7.4

Re: [PATCH v4 6/9] cpufreq: qti: Enable cpufreq for ipq53xx

[Dmitry Baryshkov]

On Thu, 19 Oct 2023 at 11:43, Varadarajan Narayanan
<quic_varada@quicinc.com> wrote:
>
> IPQ53xx have different OPPs available for the CPU based on
> SoC variant. This can be determined through use of an eFuse
> register present in the silicon.
>
> Added support for ipq53xx on nvmem driver which helps to
> determine OPPs at runtime based on the eFuse register which
> has the CPU frequency limits. opp-supported-hw dt binding
> can be used to indicate the available OPPs for each limit.
>
> nvmem driver also creates the "cpufreq-dt" platform_device after
> passing the version matching data to the OPP framework so that the
> cpufreq-dt handles the actual cpufreq implementation.
>
> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
> Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>


-- 
With best wishes
Dmitry

[PATCH v4 7/9] arm64: dts: qcom: ipq5332: populate the opp table based on the eFuse

[Varadarajan Narayanan]

IPQ53xx have different OPPs available for the CPU based on
SoC variant. This can be determined through use of an eFuse
register present in the silicon.

Add support to read the eFuse and populate the OPPs based on it.

	------------------------------------------------
	Frequency	BIT2	BIT1	opp-supported-hw
			1.1GHz	1.5GHz
	------------------------------------------------
	1100000000	1	1	0x7
	1500000000	0	1	0x3
	------------------------------------------------

Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v4:	Change opp-supported-hw from 0xf to 0x7 in commit log
	and DT entry.
v2:	Fix inconsistencies in comment and move it to commit log
	as suggested
	Remove opp-microvolt entries as no regulator is managed by Linux
	cpu_speed_bin -> cpu-speed-bin in node name
	Remove "nvmem-cell-names" due to dtbs_check error
---
 arch/arm64/boot/dts/qcom/ipq5332.dtsi | 19 ++++++++++++++++---
 1 file changed, 16 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
index 4206f05..42e2e48 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi
@@ -91,11 +91,19 @@
 	};
 
 	cpu_opp_table: opp-table-cpu {
-		compatible = "operating-points-v2";
+		compatible = "operating-points-v2-kryo-cpu";
 		opp-shared;
+		nvmem-cells = <&cpu_speed_bin>;
 
-		opp-1488000000 {
-			opp-hz = /bits/ 64 <1488000000>;
+		opp-1100000000 {
+			opp-hz = /bits/ 64 <1100000000>;
+			opp-supported-hw = <0x7>;
+			clock-latency-ns = <200000>;
+		};
+
+		opp-1500000000 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-supported-hw = <0x3>;
 			clock-latency-ns = <200000>;
 		};
 	};
@@ -163,6 +171,11 @@
 			reg = <0x000a4000 0x721>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+
+			cpu_speed_bin: cpu-speed-bin@1d {
+				reg = <0x1d 0x2>;
+				bits = <7 2>;
+			};
 		};
 
 		rng: rng@e3000 {
-- 
2.7.4

[PATCH v4 8/9] cpufreq: qti: Introduce cpufreq for ipq95xx

[Varadarajan Narayanan]

IPQ95xx SoCs have different OPPs available for the CPU based on
the SoC variant. This can be determined from an eFuse register
present in the silicon.

Added support for ipq95xx on nvmem driver which helps to
determine OPPs at runtime based on the eFuse register which
has the CPU frequency limits. opp-supported-hw dt binding
can be used to indicate the available OPPs for each limit.

Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v2:	Simplify bin selection by tweaking the order in dts
---
 drivers/cpufreq/cpufreq-dt-platdev.c | 1 +
 drivers/cpufreq/qcom-cpufreq-nvmem.c | 8 ++++++++
 2 files changed, 9 insertions(+)

diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index f43e5cd..4f794ba 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -183,6 +183,7 @@ static const struct of_device_id blocklist[] __initconst = {
 	{ .compatible = "qcom,ipq5332", },
 	{ .compatible = "qcom,ipq8064", },
 	{ .compatible = "qcom,ipq8074", },
+	{ .compatible = "qcom,ipq9574", },
 	{ .compatible = "qcom,apq8064", },
 	{ .compatible = "qcom,msm8974", },
 	{ .compatible = "qcom,msm8960", },
diff --git a/drivers/cpufreq/qcom-cpufreq-nvmem.c b/drivers/cpufreq/qcom-cpufreq-nvmem.c
index 0014909..d44be4e 100644
--- a/drivers/cpufreq/qcom-cpufreq-nvmem.c
+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c
@@ -166,6 +166,13 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev,
 	case QCOM_ID_IPQ5300:
 		drv->versions = 1 << (unsigned int)(*speedbin);
 		break;
+	case QCOM_ID_IPQ9514:
+	case QCOM_ID_IPQ9550:
+	case QCOM_ID_IPQ9554:
+	case QCOM_ID_IPQ9570:
+	case QCOM_ID_IPQ9574:
+		drv->versions = 1 << (unsigned int)(*speedbin);
+		break;
 	default:
 		BUG();
 		break;
@@ -417,6 +424,7 @@ static const struct of_device_id qcom_cpufreq_match_list[] __initconst = {
 	{ .compatible = "qcom,ipq8064", .data = &match_data_krait },
 	{ .compatible = "qcom,ipq8074", .data = &match_data_ipq8074 },
 	{ .compatible = "qcom,apq8064", .data = &match_data_krait },
+	{ .compatible = "qcom,ipq9574", .data = &match_data_kryo },
 	{ .compatible = "qcom,msm8974", .data = &match_data_krait },
 	{ .compatible = "qcom,msm8960", .data = &match_data_krait },
 	{},
-- 
2.7.4

Re: [PATCH v4 8/9] cpufreq: qti: Introduce cpufreq for ipq95xx

[Dmitry Baryshkov]

On Thu, 19 Oct 2023 at 11:43, Varadarajan Narayanan
<quic_varada@quicinc.com> wrote:
>
> IPQ95xx SoCs have different OPPs available for the CPU based on
> the SoC variant. This can be determined from an eFuse register
> present in the silicon.
>
> Added support for ipq95xx on nvmem driver which helps to
> determine OPPs at runtime based on the eFuse register which
> has the CPU frequency limits. opp-supported-hw dt binding
> can be used to indicate the available OPPs for each limit.
>
> Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org>
> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
> Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
> ---
> v2:     Simplify bin selection by tweaking the order in dts
> ---
>  drivers/cpufreq/cpufreq-dt-platdev.c | 1 +
>  drivers/cpufreq/qcom-cpufreq-nvmem.c | 8 ++++++++
>  2 files changed, 9 insertions(+)
>
> diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
> index f43e5cd..4f794ba 100644
> --- a/drivers/cpufreq/cpufreq-dt-platdev.c
> +++ b/drivers/cpufreq/cpufreq-dt-platdev.c
> @@ -183,6 +183,7 @@ static const struct of_device_id blocklist[] __initconst = {
>         { .compatible = "qcom,ipq5332", },
>         { .compatible = "qcom,ipq8064", },
>         { .compatible = "qcom,ipq8074", },
> +       { .compatible = "qcom,ipq9574", },
>         { .compatible = "qcom,apq8064", },
>         { .compatible = "qcom,msm8974", },
>         { .compatible = "qcom,msm8960", },
> diff --git a/drivers/cpufreq/qcom-cpufreq-nvmem.c b/drivers/cpufreq/qcom-cpufreq-nvmem.c
> index 0014909..d44be4e 100644
> --- a/drivers/cpufreq/qcom-cpufreq-nvmem.c
> +++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c
> @@ -166,6 +166,13 @@ static int qcom_cpufreq_kryo_name_version(struct device *cpu_dev,
>         case QCOM_ID_IPQ5300:
>                 drv->versions = 1 << (unsigned int)(*speedbin);
>                 break;
> +       case QCOM_ID_IPQ9514:
> +       case QCOM_ID_IPQ9550:
> +       case QCOM_ID_IPQ9554:
> +       case QCOM_ID_IPQ9570:
> +       case QCOM_ID_IPQ9574:

Can we please merge this to the previous set of cases (and maybe to
apq8096)? I don't see a great benefit in repeating `1 << (unsigned
int)(*speedbin)` several times.

Other than that:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

> +               drv->versions = 1 << (unsigned int)(*speedbin);
> +               break;
>         default:
>                 BUG();
>                 break;
> @@ -417,6 +424,7 @@ static const struct of_device_id qcom_cpufreq_match_list[] __initconst = {
>         { .compatible = "qcom,ipq8064", .data = &match_data_krait },
>         { .compatible = "qcom,ipq8074", .data = &match_data_ipq8074 },
>         { .compatible = "qcom,apq8064", .data = &match_data_krait },
> +       { .compatible = "qcom,ipq9574", .data = &match_data_kryo },
>         { .compatible = "qcom,msm8974", .data = &match_data_krait },
>         { .compatible = "qcom,msm8960", .data = &match_data_krait },
>         {},
> --
> 2.7.4
>


-- 
With best wishes
Dmitry

[PATCH v4 9/9] arm64: dts: qcom: ipq9574: populate the opp table based on the eFuse

[Varadarajan Narayanan]

IPQ95xx SoCs have different OPPs available for the CPU based on
SoC variant. This can be determined from an eFuse register
present in the silicon.

Add support to read the eFuse and populate the OPPs based on it.

Frequency	1.2GHz	1.8GHz	1.5GHz	No	opp-supported-hw
					Limit
------------------------------------------------------------
936000000	1	1	1	1	0xf
1104000000	1	1	1	1	0xf
1200000000	1	1	1	1	0xf
1416000000	0	1	1	1	0x7
1488000000	0	1	1	1	0x7
1800000000	0	1	0	1	0x5
2208000000	0	0	0	1	0x1
-----------------------------------------------------------

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
---
v2:	cpu_speed_bin -> cpu-speed-bin in node name
	Move comment to commit log
---
 arch/arm64/boot/dts/qcom/ipq9574.dtsi | 21 ++++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index cc84f25..5f83ee4 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -106,42 +106,56 @@
 	};
 
 	cpu_opp_table: opp-table-cpu {
-		compatible = "operating-points-v2";
+		compatible = "operating-points-v2-kryo-cpu";
 		opp-shared;
+		nvmem-cells = <&cpu_speed_bin>;
 
 		opp-936000000 {
 			opp-hz = /bits/ 64 <936000000>;
 			opp-microvolt = <725000>;
+			opp-supported-hw = <0xf>;
 			clock-latency-ns = <200000>;
 		};
 
 		opp-1104000000 {
 			opp-hz = /bits/ 64 <1104000000>;
 			opp-microvolt = <787500>;
+			opp-supported-hw = <0xf>;
+			clock-latency-ns = <200000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <862500>;
+			opp-supported-hw = <0xf>;
 			clock-latency-ns = <200000>;
 		};
 
 		opp-1416000000 {
 			opp-hz = /bits/ 64 <1416000000>;
 			opp-microvolt = <862500>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 
 		opp-1488000000 {
 			opp-hz = /bits/ 64 <1488000000>;
 			opp-microvolt = <925000>;
+			opp-supported-hw = <0x7>;
 			clock-latency-ns = <200000>;
 		};
 
 		opp-1800000000 {
 			opp-hz = /bits/ 64 <1800000000>;
 			opp-microvolt = <987500>;
+			opp-supported-hw = <0x5>;
 			clock-latency-ns = <200000>;
 		};
 
 		opp-2208000000 {
 			opp-hz = /bits/ 64 <2208000000>;
 			opp-microvolt = <1062500>;
+			opp-supported-hw = <0x1>;
 			clock-latency-ns = <200000>;
 		};
 	};
@@ -223,6 +237,11 @@
 			reg = <0x000a4000 0x5a1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+
+			cpu_speed_bin: cpu-speed-bin@15 {
+				reg = <0x15 0x2>;
+				bits = <7 2>;
+			};
 		};
 
 		cryptobam: dma-controller@704000 {
-- 
2.7.4