From: Jonathan Cameron <jic23@kernel.org>
To: Petre Rodan <petre.rodan@subdimension.ro>
Cc: linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, Andreas Klinger <ak@it-klinger.de>,
Lars-Peter Clausen <lars@metafoo.de>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>
Subject: Re: [PATCH v2 01/10] dt-bindings: iio: pressure: honeywell,mprls0025pa.yaml fix
Date: Tue, 26 Dec 2023 16:31:28 +0000 [thread overview]
Message-ID: <20231226163128.09bf0f4e@jic23-huawei> (raw)
In-Reply-To: <20231226162839.5ceddc9e@jic23-huawei>
On Tue, 26 Dec 2023 16:28:39 +0000
Jonathan Cameron <jic23@kernel.org> wrote:
> On Sun, 24 Dec 2023 16:34:46 +0200
> Petre Rodan <petre.rodan@subdimension.ro> wrote:
>
> > Define enum inside the honeywell,transfer-function property block.
> >
> > Set the correct irq edge in the example block.
> > Based on the datasheet, in table 13 on page 11:
> > "End-of-conversion indicator: This pin is set high when a measurement
> > and calculation have been completed and the data is ready to be
> > clocked out"
> >
> > Add description on End-of-conversion interrupt.
> >
> > Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
> > Signed-off-by: Andreas Klinger <ak@it-klinger.de>
> What's the relationship between Andreas and this patch?
>
> Petre seems to have sent it so either Andreas should have a Co-authored-by or
Co-developed-by: that is.
> should be the author... Or not there at all
>
> Thanks,
>
> Jonathan
>
> > ---
> > .../bindings/iio/pressure/honeywell,mprls0025pa.yaml | 7 ++++++-
> > 1 file changed, 6 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/iio/pressure/honeywell,mprls0025pa.yaml b/Documentation/devicetree/bindings/iio/pressure/honeywell,mprls0025pa.yaml
> > index d9e903fbfd99..84ced4e5a7da 100644
> > --- a/Documentation/devicetree/bindings/iio/pressure/honeywell,mprls0025pa.yaml
> > +++ b/Documentation/devicetree/bindings/iio/pressure/honeywell,mprls0025pa.yaml
> > @@ -42,6 +42,10 @@ properties:
> > maxItems: 1
> >
> > interrupts:
> > + description:
> > + Optional interrupt for indicating End-of-conversion.
> > + If not present, the driver loops for a while until the received status
> > + byte indicates correct measurement.
> > maxItems: 1
> >
> > reset-gpios:
> > @@ -65,6 +69,7 @@ properties:
> > 1 - A, 10% to 90% of 2^24 (1677722 .. 15099494)
> > 2 - B, 2.5% to 22.5% of 2^24 (419430 .. 3774874)
> > 3 - C, 20% to 80% of 2^24 (3355443 .. 13421773)
> > + enum: [1, 2, 3]
> > $ref: /schemas/types.yaml#/definitions/uint32
> >
> > vdd-supply:
> > @@ -93,7 +98,7 @@ examples:
> > reg = <0x18>;
> > reset-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> > interrupt-parent = <&gpio3>;
> > - interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
> > + interrupts = <21 IRQ_TYPE_EDGE_RISING>;
> > honeywell,pmin-pascal = <0>;
> > honeywell,pmax-pascal = <172369>;
> > honeywell,transfer-function = <1>;
> > --
> > 2.41.0
> >
>
>
next prev parent reply other threads:[~2023-12-26 16:31 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-12-24 14:34 [PATCH v2 00/10] changes to mprls0025pa Petre Rodan
2023-12-24 14:34 ` [PATCH v2 01/10] dt-bindings: iio: pressure: honeywell,mprls0025pa.yaml fix Petre Rodan
2023-12-25 12:55 ` Krzysztof Kozlowski
2023-12-26 16:28 ` Jonathan Cameron
2023-12-26 16:31 ` Jonathan Cameron [this message]
2023-12-27 7:11 ` Petre Rodan
2023-12-30 11:28 ` Jonathan Cameron
2023-12-24 14:34 ` [PATCH v2 02/10] dt-bindings: iio: pressure: honeywell,mprls0025pa.yaml add pressure-triplet Petre Rodan
2023-12-25 12:57 ` Krzysztof Kozlowski
2023-12-25 13:23 ` Petre Rodan
2023-12-25 13:34 ` Krzysztof Kozlowski
2023-12-25 13:37 ` Krzysztof Kozlowski
2023-12-25 13:58 ` Petre Rodan
2023-12-24 14:34 ` [PATCH v2 03/10] dt-bindings: iio: pressure: honeywell,mprls0025pa.yaml add spi bus Petre Rodan
2023-12-25 12:59 ` Krzysztof Kozlowski
2023-12-25 15:13 ` Petre Rodan
2023-12-25 18:56 ` Krzysztof Kozlowski
2023-12-25 20:29 ` Petre Rodan
2023-12-26 9:38 ` Krzysztof Kozlowski
2023-12-24 14:34 ` [PATCH v2 04/10] iio: pressure: mprls0025pa.c fix off-by-one enum Petre Rodan
2023-12-26 16:33 ` Jonathan Cameron
2023-12-27 16:30 ` Andy Shevchenko
2023-12-24 14:34 ` [PATCH v2 05/10] iio: pressure: mprls0025pa.c fix error flag check Petre Rodan
2023-12-26 16:35 ` Jonathan Cameron
2023-12-24 14:34 ` [PATCH v2 06/10] iio: pressure: mprls0025pa.c remove dangerous defaults Petre Rodan
2023-12-26 16:39 ` Jonathan Cameron
2023-12-24 14:34 ` [PATCH v2 07/10] iio: pressure: mprls0025pa.c whitespace cleanup Petre Rodan
2023-12-27 16:34 ` Andy Shevchenko
2023-12-27 17:39 ` Petre Rodan
2023-12-30 11:33 ` Jonathan Cameron
2024-01-06 14:03 ` Andy Shevchenko
2023-12-24 14:34 ` [PATCH v2 08/10] iio: pressure: mprls0025pa.c refactor Petre Rodan
2023-12-26 16:49 ` Jonathan Cameron
2023-12-27 14:33 ` Petre Rodan
2023-12-27 16:37 ` Andy Shevchenko
2023-12-30 11:34 ` Jonathan Cameron
2023-12-24 14:34 ` [PATCH v2 09/10] iio: pressure: mprls0025pa.c add triplet property Petre Rodan
2023-12-24 14:34 ` [PATCH v2 10/10] iio: pressure: mprls0025pa.c add SPI driver Petre Rodan
2023-12-26 16:51 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231226163128.09bf0f4e@jic23-huawei \
--to=jic23@kernel.org \
--cc=ak@it-klinger.de \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=petre.rodan@subdimension.ro \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.