All of lore.kernel.org
 help / color / mirror / Atom feed
From: git@luigi311.com
To: linux-media@vger.kernel.org
Cc: dave.stevenson@raspberrypi.com, jacopo.mondi@ideasonboard.com,
	mchehab@kernel.org, robh@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org,
	shawnguo@kernel.org, s.hauer@pengutronix.de,
	kernel@pengutronix.de, festevam@gmail.com,
	sakari.ailus@linux.intel.com, devicetree@vger.kernel.org,
	imx@lists.linux.dev, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, pavel@ucw.cz,
	phone-devel@vger.kernel.org, Luis Garcia <git@luigi311.com>
Subject: [PATCH v4 20/25] media: i2c: imx258: Make HFLIP and VFLIP controls writable
Date: Sun, 14 Apr 2024 14:34:58 -0600	[thread overview]
Message-ID: <20240414203503.18402-21-git@luigi311.com> (raw)
In-Reply-To: <20240414203503.18402-1-git@luigi311.com>

From: Dave Stevenson <dave.stevenson@raspberrypi.com>

The sensor supports H & V flips, but the controls were READ_ONLY.

Note that the Bayer order changes with these flips, therefore
they set the V4L2_CTRL_FLAG_MODIFY_LAYOUT property.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
---
 drivers/media/i2c/imx258.c | 100 ++++++++++++++++++++++++-------------
 1 file changed, 65 insertions(+), 35 deletions(-)

diff --git a/drivers/media/i2c/imx258.c b/drivers/media/i2c/imx258.c
index 54f7625e60a3..f043200e336e 100644
--- a/drivers/media/i2c/imx258.c
+++ b/drivers/media/i2c/imx258.c
@@ -78,8 +78,8 @@
 
 /* Orientation */
 #define REG_MIRROR_FLIP_CONTROL		0x0101
-#define REG_CONFIG_MIRROR_FLIP		0x03
-#define REG_CONFIG_FLIP_TEST_PATTERN	0x02
+#define REG_CONFIG_MIRROR_HFLIP		0x01
+#define REG_CONFIG_MIRROR_VFLIP		0x02
 
 /* IMX258 native and active pixel array size. */
 #define IMX258_NATIVE_WIDTH		4224U
@@ -484,6 +484,23 @@ static const struct imx258_variant_cfg imx258_pdaf_cfg = {
 	.num_regs = ARRAY_SIZE(imx258_pdaf_cfg_regs),
 };
 
+/*
+ * The supported formats.
+ * This table MUST contain 4 entries per format, to cover the various flip
+ * combinations in the order
+ * - no flip
+ * - h flip
+ * - v flip
+ * - h&v flips
+ */
+static const u32 codes[] = {
+	/* 10-bit modes. */
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SBGGR10_1X10
+};
+
 static const char * const imx258_test_pattern_menu[] = {
 	"Disabled",
 	"Solid Colour",
@@ -670,6 +687,8 @@ struct imx258 {
 	struct v4l2_ctrl *vblank;
 	struct v4l2_ctrl *hblank;
 	struct v4l2_ctrl *exposure;
+	struct v4l2_ctrl *hflip;
+	struct v4l2_ctrl *vflip;
 
 	/* Current mode */
 	const struct imx258_mode *cur_mode;
@@ -768,9 +787,23 @@ static int imx258_write_regs(struct imx258 *imx258,
 	return 0;
 }
 
+/* Get bayer order based on flip setting. */
+static u32 imx258_get_format_code(const struct imx258 *imx258)
+{
+	unsigned int i;
+
+	lockdep_assert_held(&imx258->mutex);
+
+	i = (imx258->vflip->val ? 2 : 0) |
+	    (imx258->hflip->val ? 1 : 0);
+
+	return codes[i];
+}
+
 /* Open sub-device */
 static int imx258_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
 {
+	struct imx258 *imx258 = to_imx258(sd);
 	struct v4l2_mbus_framefmt *try_fmt =
 		v4l2_subdev_state_get_format(fh->state, 0);
 	struct v4l2_rect *try_crop;
@@ -778,7 +811,7 @@ static int imx258_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
 	/* Initialize try_fmt */
 	try_fmt->width = supported_modes[0].width;
 	try_fmt->height = supported_modes[0].height;
-	try_fmt->code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	try_fmt->code = imx258_get_format_code(imx258);
 	try_fmt->field = V4L2_FIELD_NONE;
 
 	/* Initialize try_crop */
@@ -871,10 +904,6 @@ static int imx258_set_ctrl(struct v4l2_ctrl *ctrl)
 		ret = imx258_write_reg(imx258, IMX258_REG_TEST_PATTERN,
 				IMX258_REG_VALUE_16BIT,
 				ctrl->val);
-		ret = imx258_write_reg(imx258, REG_MIRROR_FLIP_CONTROL,
-				IMX258_REG_VALUE_08BIT,
-				!ctrl->val ? REG_CONFIG_MIRROR_FLIP :
-				REG_CONFIG_FLIP_TEST_PATTERN);
 		break;
 	case V4L2_CID_WIDE_DYNAMIC_RANGE:
 		if (!ctrl->val) {
@@ -897,6 +926,15 @@ static int imx258_set_ctrl(struct v4l2_ctrl *ctrl)
 				       IMX258_REG_VALUE_16BIT,
 				       imx258->cur_mode->height + ctrl->val);
 		break;
+	case V4L2_CID_VFLIP:
+	case V4L2_CID_HFLIP:
+		ret = imx258_write_reg(imx258, REG_MIRROR_FLIP_CONTROL,
+				       IMX258_REG_VALUE_08BIT,
+				       (imx258->hflip->val ?
+					REG_CONFIG_MIRROR_HFLIP : 0) |
+				       (imx258->vflip->val ?
+					REG_CONFIG_MIRROR_VFLIP : 0));
+		break;
 	default:
 		dev_info(&client->dev,
 			 "ctrl(id:0x%x,val:0x%x) is not handled\n",
@@ -918,11 +956,13 @@ static int imx258_enum_mbus_code(struct v4l2_subdev *sd,
 				  struct v4l2_subdev_state *sd_state,
 				  struct v4l2_subdev_mbus_code_enum *code)
 {
-	/* Only one bayer order(GRBG) is supported */
+	struct imx258 *imx258 = to_imx258(sd);
+
+	/* Only one bayer format (10 bit) is supported */
 	if (code->index > 0)
 		return -EINVAL;
 
-	code->code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	code->code = imx258_get_format_code(imx258);
 
 	return 0;
 }
@@ -931,10 +971,11 @@ static int imx258_enum_frame_size(struct v4l2_subdev *sd,
 				  struct v4l2_subdev_state *sd_state,
 				  struct v4l2_subdev_frame_size_enum *fse)
 {
+	struct imx258 *imx258 = to_imx258(sd);
 	if (fse->index >= ARRAY_SIZE(supported_modes))
 		return -EINVAL;
 
-	if (fse->code != MEDIA_BUS_FMT_SBGGR10_1X10)
+	if (fse->code != imx258_get_format_code(imx258))
 		return -EINVAL;
 
 	fse->min_width = supported_modes[fse->index].width;
@@ -945,12 +986,13 @@ static int imx258_enum_frame_size(struct v4l2_subdev *sd,
 	return 0;
 }
 
-static void imx258_update_pad_format(const struct imx258_mode *mode,
+static void imx258_update_pad_format(struct imx258 *imx258,
+				     const struct imx258_mode *mode,
 				     struct v4l2_subdev_format *fmt)
 {
 	fmt->format.width = mode->width;
 	fmt->format.height = mode->height;
-	fmt->format.code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	fmt->format.code = imx258_get_format_code(imx258);
 	fmt->format.field = V4L2_FIELD_NONE;
 }
 
@@ -962,7 +1004,7 @@ static int __imx258_get_pad_format(struct imx258 *imx258,
 		fmt->format = *v4l2_subdev_state_get_format(sd_state,
 							    fmt->pad);
 	else
-		imx258_update_pad_format(imx258->cur_mode, fmt);
+		imx258_update_pad_format(imx258, imx258->cur_mode, fmt);
 
 	return 0;
 }
@@ -998,13 +1040,12 @@ static int imx258_set_pad_format(struct v4l2_subdev *sd,
 
 	mutex_lock(&imx258->mutex);
 
-	/* Only one raw bayer(GBRG) order is supported */
-	fmt->format.code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	fmt->format.code = imx258_get_format_code(imx258);
 
 	mode = v4l2_find_nearest_size(supported_modes,
 		ARRAY_SIZE(supported_modes), width, height,
 		fmt->format.width, fmt->format.height);
-	imx258_update_pad_format(mode, fmt);
+	imx258_update_pad_format(imx258, mode, fmt);
 	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
 		framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
 		*framefmt = fmt->format;
@@ -1154,15 +1195,6 @@ static int imx258_start_streaming(struct imx258 *imx258)
 		return ret;
 	}
 
-	/* Set Orientation be 180 degree */
-	ret = imx258_write_reg(imx258, REG_MIRROR_FLIP_CONTROL,
-			       IMX258_REG_VALUE_08BIT, REG_CONFIG_MIRROR_FLIP);
-	if (ret) {
-		dev_err(&client->dev, "%s failed to set orientation\n",
-			__func__);
-		return ret;
-	}
-
 	/* Apply customized values from user */
 	ret =  __v4l2_ctrl_handler_setup(imx258->sd.ctrl_handler);
 	if (ret)
@@ -1315,7 +1347,6 @@ static int imx258_init_controls(struct imx258 *imx258)
 	struct i2c_client *client = v4l2_get_subdevdata(&imx258->sd);
 	const struct imx258_link_freq_config *link_freq_cfgs;
 	struct v4l2_fwnode_device_properties props;
-	struct v4l2_ctrl *vflip, *hflip;
 	struct v4l2_ctrl_handler *ctrl_hdlr;
 	const struct imx258_link_cfg *link_cfg;
 	s64 vblank_def;
@@ -1340,16 +1371,15 @@ static int imx258_init_controls(struct imx258 *imx258)
 	if (imx258->link_freq)
 		imx258->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
 
-	/* The driver only supports one bayer order and flips by default. */
-	hflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx258_ctrl_ops,
-				  V4L2_CID_HFLIP, 1, 1, 1, 1);
-	if (hflip)
-		hflip->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+	imx258->hflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx258_ctrl_ops,
+					  V4L2_CID_HFLIP, 0, 1, 1, 1);
+	if (imx258->hflip)
+		imx258->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
 
-	vflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx258_ctrl_ops,
-				  V4L2_CID_VFLIP, 1, 1, 1, 1);
-	if (vflip)
-		vflip->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+	imx258->vflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx258_ctrl_ops,
+					  V4L2_CID_VFLIP, 0, 1, 1, 1);
+	if (imx258->vflip)
+		imx258->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
 
 	link_freq_cfgs = &imx258->link_freq_configs[0];
 	link_cfg = link_freq_cfgs[imx258->lane_mode_idx].link_cfg;
-- 
2.44.0


WARNING: multiple messages have this Message-ID (diff)
From: git@luigi311.com
To: linux-media@vger.kernel.org
Cc: dave.stevenson@raspberrypi.com, jacopo.mondi@ideasonboard.com,
	mchehab@kernel.org, robh@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org,
	shawnguo@kernel.org, s.hauer@pengutronix.de,
	kernel@pengutronix.de, festevam@gmail.com,
	sakari.ailus@linux.intel.com, devicetree@vger.kernel.org,
	imx@lists.linux.dev, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, pavel@ucw.cz,
	phone-devel@vger.kernel.org, Luis Garcia <git@luigi311.com>
Subject: [PATCH v4 20/25] media: i2c: imx258: Make HFLIP and VFLIP controls writable
Date: Sun, 14 Apr 2024 14:34:58 -0600	[thread overview]
Message-ID: <20240414203503.18402-21-git@luigi311.com> (raw)
In-Reply-To: <20240414203503.18402-1-git@luigi311.com>

From: Dave Stevenson <dave.stevenson@raspberrypi.com>

The sensor supports H & V flips, but the controls were READ_ONLY.

Note that the Bayer order changes with these flips, therefore
they set the V4L2_CTRL_FLAG_MODIFY_LAYOUT property.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
---
 drivers/media/i2c/imx258.c | 100 ++++++++++++++++++++++++-------------
 1 file changed, 65 insertions(+), 35 deletions(-)

diff --git a/drivers/media/i2c/imx258.c b/drivers/media/i2c/imx258.c
index 54f7625e60a3..f043200e336e 100644
--- a/drivers/media/i2c/imx258.c
+++ b/drivers/media/i2c/imx258.c
@@ -78,8 +78,8 @@
 
 /* Orientation */
 #define REG_MIRROR_FLIP_CONTROL		0x0101
-#define REG_CONFIG_MIRROR_FLIP		0x03
-#define REG_CONFIG_FLIP_TEST_PATTERN	0x02
+#define REG_CONFIG_MIRROR_HFLIP		0x01
+#define REG_CONFIG_MIRROR_VFLIP		0x02
 
 /* IMX258 native and active pixel array size. */
 #define IMX258_NATIVE_WIDTH		4224U
@@ -484,6 +484,23 @@ static const struct imx258_variant_cfg imx258_pdaf_cfg = {
 	.num_regs = ARRAY_SIZE(imx258_pdaf_cfg_regs),
 };
 
+/*
+ * The supported formats.
+ * This table MUST contain 4 entries per format, to cover the various flip
+ * combinations in the order
+ * - no flip
+ * - h flip
+ * - v flip
+ * - h&v flips
+ */
+static const u32 codes[] = {
+	/* 10-bit modes. */
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SBGGR10_1X10
+};
+
 static const char * const imx258_test_pattern_menu[] = {
 	"Disabled",
 	"Solid Colour",
@@ -670,6 +687,8 @@ struct imx258 {
 	struct v4l2_ctrl *vblank;
 	struct v4l2_ctrl *hblank;
 	struct v4l2_ctrl *exposure;
+	struct v4l2_ctrl *hflip;
+	struct v4l2_ctrl *vflip;
 
 	/* Current mode */
 	const struct imx258_mode *cur_mode;
@@ -768,9 +787,23 @@ static int imx258_write_regs(struct imx258 *imx258,
 	return 0;
 }
 
+/* Get bayer order based on flip setting. */
+static u32 imx258_get_format_code(const struct imx258 *imx258)
+{
+	unsigned int i;
+
+	lockdep_assert_held(&imx258->mutex);
+
+	i = (imx258->vflip->val ? 2 : 0) |
+	    (imx258->hflip->val ? 1 : 0);
+
+	return codes[i];
+}
+
 /* Open sub-device */
 static int imx258_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
 {
+	struct imx258 *imx258 = to_imx258(sd);
 	struct v4l2_mbus_framefmt *try_fmt =
 		v4l2_subdev_state_get_format(fh->state, 0);
 	struct v4l2_rect *try_crop;
@@ -778,7 +811,7 @@ static int imx258_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
 	/* Initialize try_fmt */
 	try_fmt->width = supported_modes[0].width;
 	try_fmt->height = supported_modes[0].height;
-	try_fmt->code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	try_fmt->code = imx258_get_format_code(imx258);
 	try_fmt->field = V4L2_FIELD_NONE;
 
 	/* Initialize try_crop */
@@ -871,10 +904,6 @@ static int imx258_set_ctrl(struct v4l2_ctrl *ctrl)
 		ret = imx258_write_reg(imx258, IMX258_REG_TEST_PATTERN,
 				IMX258_REG_VALUE_16BIT,
 				ctrl->val);
-		ret = imx258_write_reg(imx258, REG_MIRROR_FLIP_CONTROL,
-				IMX258_REG_VALUE_08BIT,
-				!ctrl->val ? REG_CONFIG_MIRROR_FLIP :
-				REG_CONFIG_FLIP_TEST_PATTERN);
 		break;
 	case V4L2_CID_WIDE_DYNAMIC_RANGE:
 		if (!ctrl->val) {
@@ -897,6 +926,15 @@ static int imx258_set_ctrl(struct v4l2_ctrl *ctrl)
 				       IMX258_REG_VALUE_16BIT,
 				       imx258->cur_mode->height + ctrl->val);
 		break;
+	case V4L2_CID_VFLIP:
+	case V4L2_CID_HFLIP:
+		ret = imx258_write_reg(imx258, REG_MIRROR_FLIP_CONTROL,
+				       IMX258_REG_VALUE_08BIT,
+				       (imx258->hflip->val ?
+					REG_CONFIG_MIRROR_HFLIP : 0) |
+				       (imx258->vflip->val ?
+					REG_CONFIG_MIRROR_VFLIP : 0));
+		break;
 	default:
 		dev_info(&client->dev,
 			 "ctrl(id:0x%x,val:0x%x) is not handled\n",
@@ -918,11 +956,13 @@ static int imx258_enum_mbus_code(struct v4l2_subdev *sd,
 				  struct v4l2_subdev_state *sd_state,
 				  struct v4l2_subdev_mbus_code_enum *code)
 {
-	/* Only one bayer order(GRBG) is supported */
+	struct imx258 *imx258 = to_imx258(sd);
+
+	/* Only one bayer format (10 bit) is supported */
 	if (code->index > 0)
 		return -EINVAL;
 
-	code->code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	code->code = imx258_get_format_code(imx258);
 
 	return 0;
 }
@@ -931,10 +971,11 @@ static int imx258_enum_frame_size(struct v4l2_subdev *sd,
 				  struct v4l2_subdev_state *sd_state,
 				  struct v4l2_subdev_frame_size_enum *fse)
 {
+	struct imx258 *imx258 = to_imx258(sd);
 	if (fse->index >= ARRAY_SIZE(supported_modes))
 		return -EINVAL;
 
-	if (fse->code != MEDIA_BUS_FMT_SBGGR10_1X10)
+	if (fse->code != imx258_get_format_code(imx258))
 		return -EINVAL;
 
 	fse->min_width = supported_modes[fse->index].width;
@@ -945,12 +986,13 @@ static int imx258_enum_frame_size(struct v4l2_subdev *sd,
 	return 0;
 }
 
-static void imx258_update_pad_format(const struct imx258_mode *mode,
+static void imx258_update_pad_format(struct imx258 *imx258,
+				     const struct imx258_mode *mode,
 				     struct v4l2_subdev_format *fmt)
 {
 	fmt->format.width = mode->width;
 	fmt->format.height = mode->height;
-	fmt->format.code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	fmt->format.code = imx258_get_format_code(imx258);
 	fmt->format.field = V4L2_FIELD_NONE;
 }
 
@@ -962,7 +1004,7 @@ static int __imx258_get_pad_format(struct imx258 *imx258,
 		fmt->format = *v4l2_subdev_state_get_format(sd_state,
 							    fmt->pad);
 	else
-		imx258_update_pad_format(imx258->cur_mode, fmt);
+		imx258_update_pad_format(imx258, imx258->cur_mode, fmt);
 
 	return 0;
 }
@@ -998,13 +1040,12 @@ static int imx258_set_pad_format(struct v4l2_subdev *sd,
 
 	mutex_lock(&imx258->mutex);
 
-	/* Only one raw bayer(GBRG) order is supported */
-	fmt->format.code = MEDIA_BUS_FMT_SBGGR10_1X10;
+	fmt->format.code = imx258_get_format_code(imx258);
 
 	mode = v4l2_find_nearest_size(supported_modes,
 		ARRAY_SIZE(supported_modes), width, height,
 		fmt->format.width, fmt->format.height);
-	imx258_update_pad_format(mode, fmt);
+	imx258_update_pad_format(imx258, mode, fmt);
 	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
 		framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
 		*framefmt = fmt->format;
@@ -1154,15 +1195,6 @@ static int imx258_start_streaming(struct imx258 *imx258)
 		return ret;
 	}
 
-	/* Set Orientation be 180 degree */
-	ret = imx258_write_reg(imx258, REG_MIRROR_FLIP_CONTROL,
-			       IMX258_REG_VALUE_08BIT, REG_CONFIG_MIRROR_FLIP);
-	if (ret) {
-		dev_err(&client->dev, "%s failed to set orientation\n",
-			__func__);
-		return ret;
-	}
-
 	/* Apply customized values from user */
 	ret =  __v4l2_ctrl_handler_setup(imx258->sd.ctrl_handler);
 	if (ret)
@@ -1315,7 +1347,6 @@ static int imx258_init_controls(struct imx258 *imx258)
 	struct i2c_client *client = v4l2_get_subdevdata(&imx258->sd);
 	const struct imx258_link_freq_config *link_freq_cfgs;
 	struct v4l2_fwnode_device_properties props;
-	struct v4l2_ctrl *vflip, *hflip;
 	struct v4l2_ctrl_handler *ctrl_hdlr;
 	const struct imx258_link_cfg *link_cfg;
 	s64 vblank_def;
@@ -1340,16 +1371,15 @@ static int imx258_init_controls(struct imx258 *imx258)
 	if (imx258->link_freq)
 		imx258->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
 
-	/* The driver only supports one bayer order and flips by default. */
-	hflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx258_ctrl_ops,
-				  V4L2_CID_HFLIP, 1, 1, 1, 1);
-	if (hflip)
-		hflip->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+	imx258->hflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx258_ctrl_ops,
+					  V4L2_CID_HFLIP, 0, 1, 1, 1);
+	if (imx258->hflip)
+		imx258->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
 
-	vflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx258_ctrl_ops,
-				  V4L2_CID_VFLIP, 1, 1, 1, 1);
-	if (vflip)
-		vflip->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+	imx258->vflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx258_ctrl_ops,
+					  V4L2_CID_VFLIP, 0, 1, 1, 1);
+	if (imx258->vflip)
+		imx258->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
 
 	link_freq_cfgs = &imx258->link_freq_configs[0];
 	link_cfg = link_freq_cfgs[imx258->lane_mode_idx].link_cfg;
-- 
2.44.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2024-04-14 20:41 UTC|newest]

Thread overview: 72+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-04-14 20:34 [PATCH v4 00/25] imx258 improvement series git
2024-04-14 20:34 ` git
2024-04-14 20:34 ` [PATCH v4 01/25] media: i2c: imx258: Remove unused defines git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 02/25] media: i2c: imx258: Make image geometry meet sensor requirements git
2024-04-14 20:34   ` git
2024-04-15  6:25   ` Alexander Stein
2024-04-15  6:25     ` Alexander Stein
2024-04-15 16:38     ` Luis Garcia
2024-04-15 16:38       ` Luis Garcia
2024-04-16 15:18     ` Dave Stevenson
2024-04-16 15:18       ` Dave Stevenson
2024-04-14 20:34 ` [PATCH v4 03/25] media: i2c: imx258: Disable digital cropping on binned modes git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 04/25] media: i2c: imx258: Remove redundant I2C writes git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 05/25] media: i2c: imx258: Add regulator control git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 06/25] media: i2c: imx258: Make V4L2_CID_VBLANK configurable git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 07/25] media: i2c: imx258: Split out common registers from the mode based ones git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 08/25] media: i2c: imx258: Add support for 24MHz clock git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 09/25] media: i2c: imx258: Add support for running on 2 CSI data lanes git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 10/25] media: i2c: imx258: Follow normal V4L2 behaviours for clipping exposure git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 11/25] media: i2c: imx258: Add get_selection for pixel array information git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 12/25] media: i2c: imx258: Allow configuration of clock lane behaviour git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 13/25] media: i2c: imx258: Correct max FRM_LENGTH_LINES value git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 14/25] media: i2c: imx258: Issue reset before starting streaming git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 15/25] media: i2c: imx258: Set pixel_rate range to the same as the value git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 16/25] media: i2c: imx258: Support faster pixel rate on binned modes git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 17/25] dt-bindings: media: imx258: Rename to include vendor prefix git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 18/25] dt-bindings: media: imx258: Add alternate compatible strings git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` [PATCH v4 19/25] media: i2c: imx258: Change register settings for variants of the sensor git
2024-04-14 20:34   ` git
2024-04-14 20:34 ` git [this message]
2024-04-14 20:34   ` [PATCH v4 20/25] media: i2c: imx258: Make HFLIP and VFLIP controls writable git
2024-04-14 20:34 ` [PATCH v4 21/25] dt-bindings: media: imx258: Add binding for powerdown-gpio git
2024-04-14 20:34   ` git
2024-04-14 20:35 ` [PATCH v4 22/25] media: i2c: imx258: Add support for powerdown gpio git
2024-04-14 20:35   ` git
2024-04-14 20:35 ` [PATCH v4 23/25] media: i2c: imx258: Add support for reset gpio git
2024-04-14 20:35   ` git
2024-04-15 16:00   ` Tommaso Merciai
2024-04-15 16:00     ` Tommaso Merciai
2024-04-15 16:25     ` Luis Garcia
2024-04-15 16:25       ` Luis Garcia
2024-04-14 20:35 ` [PATCH v4 24/25] media:i2c: imx258: Use v4l2_link_freq_to_bitmap helper git
2024-04-14 20:35   ` git
2024-04-15 15:18   ` Tommaso Merciai
2024-04-15 15:18     ` Tommaso Merciai
2024-04-15 16:27     ` Luis Garcia
2024-04-15 16:27       ` Luis Garcia
2024-04-15 16:32       ` Tommaso Merciai
2024-04-15 16:32         ` Tommaso Merciai
2024-04-14 20:35 ` [PATCH v4 25/25] media: i2c: imx258: Convert to new CCI register access helpers git
2024-04-14 20:35   ` git
2024-04-15 14:47   ` Tommaso Merciai
2024-04-15 14:47     ` Tommaso Merciai
2024-04-15 15:29     ` Luis Garcia
2024-04-15 15:29       ` Luis Garcia

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20240414203503.18402-21-git@luigi311.com \
    --to=git@luigi311.com \
    --cc=conor+dt@kernel.org \
    --cc=dave.stevenson@raspberrypi.com \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=imx@lists.linux.dev \
    --cc=jacopo.mondi@ideasonboard.com \
    --cc=kernel@pengutronix.de \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=mchehab@kernel.org \
    --cc=pavel@ucw.cz \
    --cc=phone-devel@vger.kernel.org \
    --cc=robh@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=sakari.ailus@linux.intel.com \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.