Re: [PATCH v3 08/11] PCI: imx: Config look up table(LUT) to support MSI ITS and IOMMU for i.MX95

[Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>]

PCI: imx6: Add support for configuring BDF to SID mapping for i.MX95

On Tue, Apr 02, 2024 at 10:33:44AM -0400, Frank Li wrote:
> i.MX95 need config LUT to convert bpf to stream id. IOMMU and ITS use the

Did you mean BDF? Here and everywhere.

> same stream id. Check msi-map and smmu-map and make sure the same PCI bpf
> map to the same stream id. Then config LUT related registers.
> 

These DT properties not documented in the binding.

> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
>  drivers/pci/controller/dwc/pcie-imx.c | 175 ++++++++++++++++++++++++++++++++++
>  1 file changed, 175 insertions(+)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-imx.c b/drivers/pci/controller/dwc/pcie-imx.c
> index af0f960f28757..653d8e8ee1abc 100644
> --- a/drivers/pci/controller/dwc/pcie-imx.c
> +++ b/drivers/pci/controller/dwc/pcie-imx.c
> @@ -55,6 +55,22 @@
>  #define IMX95_PE0_GEN_CTRL_3			0x1058
>  #define IMX95_PCIE_LTSSM_EN			BIT(0)
>  
> +#define IMX95_PE0_LUT_ACSCTRL			0x1008
> +#define IMX95_PEO_LUT_RWA			BIT(16)
> +#define IMX95_PE0_LUT_ENLOC			GENMASK(4, 0)
> +
> +#define IMX95_PE0_LUT_DATA1			0x100c
> +#define IMX95_PE0_LUT_VLD			BIT(31)
> +#define IMX95_PE0_LUT_DAC_ID			GENMASK(10, 8)
> +#define IMX95_PE0_LUT_STREAM_ID			GENMASK(5, 0)
> +
> +#define IMX95_PE0_LUT_DATA2			0x1010
> +#define IMX95_PE0_LUT_REQID			GENMASK(31, 16)
> +#define IMX95_PE0_LUT_MASK			GENMASK(15, 0)
> +
> +#define IMX95_SID_MASK				GENMASK(5, 0)
> +#define IMX95_MAX_LUT				32
> +
>  #define to_imx_pcie(x)	dev_get_drvdata((x)->dev)
>  
>  enum imx_pcie_variants {
> @@ -217,6 +233,159 @@ static int imx95_pcie_init_phy(struct imx_pcie *imx_pcie)
>  	return 0;
>  }
>  
> +static int imx_pcie_update_lut(struct imx_pcie *imx_pcie, int index, u16 reqid, u16 mask, u8 sid)
> +{
> +	struct dw_pcie *pci = imx_pcie->pci;
> +	struct device *dev = pci->dev;
> +	u32 data1, data2;
> +
> +	if (sid >= 64) {
> +		dev_err(dev, "Too big stream id: %d\n", sid);

'Invalid SID for index (%d): %d\n', index, sid

> +		return -EINVAL;
> +	}
> +
> +	data1 = FIELD_PREP(IMX95_PE0_LUT_DAC_ID, 0);
> +	data1 |= FIELD_PREP(IMX95_PE0_LUT_STREAM_ID, sid);
> +	data1 |= IMX95_PE0_LUT_VLD;
> +
> +	regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, data1);
> +
> +	data2 = mask;
> +	data2 |= FIELD_PREP(IMX95_PE0_LUT_REQID, reqid);
> +
> +	regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, data2);
> +
> +	regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, index);
> +
> +	return 0;
> +}
> +
> +struct imx_of_map {

imx_iommu_map

> +	u32 bdf;
> +	u32 phandle;
> +	u32 sid;
> +	u32 sid_len;
> +};
> +
> +static int imx_check_msi_and_smmmu(struct imx_pcie *imx_pcie,
> +				   struct imx_of_map *msi_map, u32 msi_size, u32 msi_map_mask,
> +				   struct imx_of_map *smmu_map, u32 smmu_size, u32 smmu_map_mask)
> +{
> +	struct dw_pcie *pci = imx_pcie->pci;
> +	struct device *dev = pci->dev;
> +	int i;
> +

	if (!msi_map || !smmu_map)
		return 0;

> +	if (msi_map && smmu_map) {
> +		if (msi_size != smmu_size)
> +			return -EINVAL;
> +		if (msi_map_mask != smmu_map_mask)
> +			return -EINVAL;

	if (msi_size != smmu_size || msi_map_mask != smmu_map_mask)
		return -EINVAL;

> +
> +		for (i = 0; i < msi_size / sizeof(*msi_map); i++) {
> +			if (msi_map->bdf != smmu_map->bdf) {
> +				dev_err(dev, "bdf setting is not match\n");

'BDF mismatch between msi-map and iommu-map'

> +				return -EINVAL;
> +			}
> +			if ((msi_map->sid & IMX95_SID_MASK) != smmu_map->sid) {
> +				dev_err(dev, "sid setting is not match\n");

'SID mismatch between msi-map and iommu-map'

> +				return -EINVAL;
> +			}
> +			if ((msi_map->sid_len & IMX95_SID_MASK) != smmu_map->sid_len) {
> +				dev_err(dev, "sid_len setting is not match\n");

'SID length  mismatch between msi-map and iommu-map'

> +				return -EINVAL;
> +			}
> +		}
> +	}
> +
> +	return 0;
> +}
> +
> +/*
> + * Simple static config lut according to dts settings DAC index and stream ID used as a match result
> + * of LUT pre-allocated and used by PCIes.
> + *

Please reword the above sentence.

> + * Currently stream ID from 32-64 for PCIe.
> + * 32-40: first PCI bus.
> + * 40-48: second PCI bus.

I believe this is an SoC specific info. So better not add it here. It belongs to
DT.

> + *
> + * DAC_ID is index of TRDC.DAC index, start from 2 at iMX95.
> + * ITS [pci(2bit): streamid(6bits)]
> + *	pci 0 is 0
> + *	pci 1 is 3
> + */
> +static int imx_pcie_config_sid(struct imx_pcie *imx_pcie)
> +{
> +	struct imx_of_map *msi_map = NULL, *smmu_map = NULL, *cur;
> +	int i, j, lut_index, nr_map, msi_size = 0, smmu_size = 0;
> +	u32 msi_map_mask = 0xffff, smmu_map_mask = 0xffff;
> +	struct dw_pcie *pci = imx_pcie->pci;
> +	struct device *dev = pci->dev;
> +	u32 mask;
> +	int size;
> +
> +	of_get_property(dev->of_node, "msi-map", &msi_size);
> +	if (msi_size) {

You mentioned in the commit message that msi-map and iommu-map needs to be the
same for this SoC. But here you are just ignoring the absence of 'msi-map'
property.

> +		msi_map = devm_kzalloc(dev, msi_size, GFP_KERNEL);
> +		if (!msi_map)
> +			return -ENOMEM;
> +
> +		if (of_property_read_u32_array(dev->of_node, "msi-map", (u32 *)msi_map,
> +					       msi_size / sizeof(u32)))
> +			return -EINVAL;
> +
> +		of_property_read_u32(dev->of_node, "msi-map-mask", &msi_map_mask);
> +	}
> +
> +	cur = msi_map;
> +	size = msi_size;
> +	mask = msi_map_mask;
> +
> +	of_get_property(dev->of_node, "iommu-map", &smmu_size);

Same comment as above.

> +	if (smmu_size) {
> +		smmu_map = devm_kzalloc(dev, smmu_size, GFP_KERNEL);
> +		if (!smmu_map)
> +			return -ENOMEM;
> +
> +		if (of_property_read_u32_array(dev->of_node, "iommu-map", (u32 *)smmu_map,
> +					       smmu_size / sizeof(u32)))
> +			return -EINVAL;
> +
> +		of_property_read_u32(dev->of_node, "iommu_map_mask", &smmu_map_mask);
> +	}
> +
> +	if (imx_check_msi_and_smmmu(imx_pcie, msi_map, msi_size, msi_map_mask,
> +				     smmu_map, smmu_size, smmu_map_mask))
> +		return -EINVAL;
> +

Hmm, so you want to continue even if the 'msi-map' and 'iommu-map' properties
don't exist i.e., for old platforms?

> +	if (!cur) {
> +		cur = smmu_map;
> +		size = smmu_size;
> +		mask = smmu_map_mask;
> +	}
> +
> +	nr_map = size / (sizeof(*cur));
> +
> +	lut_index = 0;

Just initialize it while defining itself.

> +	for (i = 0; i < nr_map; i++) {
> +		for (j = 0; j < cur->sid_len; j++) {
> +			imx_pcie_update_lut(imx_pcie, lut_index, cur->bdf + j, mask,
> +					    (cur->sid + j) & IMX95_SID_MASK);
> +			lut_index++;
> +		}
> +		cur++;
> +
> +		if (lut_index >= IMX95_MAX_LUT) {
> +			dev_err(dev, "its-map/iommu-map exceed HW limiation\n");

'Too many msi-map/iommu-map entries'

But I think you can just continue to use the allowed entries.

> +			return -EINVAL;
> +		}
> +	}
> +
> +	devm_kfree(dev, smmu_map);
> +	devm_kfree(dev, msi_map);

Please don't explicitly free the devm_ managed resources unless really needed.
Else don't use devm_ at all.

> +
> +	return 0;
> +}
> +
>  static void imx_pcie_configure_type(struct imx_pcie *imx_pcie)
>  {
>  	const struct imx_pcie_drvdata *drvdata = imx_pcie->drvdata;
> @@ -950,6 +1119,12 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
>  		goto err_phy_off;
>  	}
>  
> +	ret = imx_pcie_config_sid(imx_pcie);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to config sid:%d\n", ret);

'Failed to config BDF to SID mapping: %d\n'

- Mani

-- 
மணிவண்ணன் சதாசிவம்