[PATCH 0/7] can: m_can: Add am62 wakeup support - Markus Schneider-Pargmann

From: Markus Schneider-Pargmann <msp@baylibre.com>
To: Chandrasekar Ramakrishnan <rcsekar@samsung.com>,
	Marc Kleine-Budde <mkl@pengutronix.de>,
	Vincent Mailhol <mailhol.vincent@wanadoo.fr>,
	"David S . Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>, Nishanth Menon <nm@ti.com>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Tero Kristo <kristo@kernel.org>
Cc: "Vibhore Vardhan" <vibhore@ti.com>,
	"Kevin Hilman" <khilman@baylibre.com>,
	"Dhruva Gole" <d-gole@ti.com>,
	"Martin Hundebøll" <martin@geanix.com>,
	"Simon Horman" <horms@kernel.org>,
	linux-can@vger.kernel.org, netdev@vger.kernel.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	"Markus Schneider-Pargmann" <msp@baylibre.com>
Subject: [PATCH 0/7] can: m_can: Add am62 wakeup support
Date: Thu, 23 May 2024 09:53:40 +0200	[thread overview]
Message-ID: <20240523075347.1282395-1-msp@baylibre.com> (raw)

Hi,

am62, am62a and am62p support Partial-IO, a poweroff SoC state with a
few pin groups being active for wakeup.

To support mcu_mcan0 and mcu_mcan1 wakeup for the mentioned SoCs, the
series introduces a notion of wake-on-lan for m_can. If the user decides
to enable wake-on-lan for a m_can device, the device is set to wakeup
enabled. A 'wakeup' pinctrl state is selected to enable wakeup flags for
the relevant pins. If wake-on-lan is disabled the default pinctrl is
selected.

It is based on v6.9-rc1.

This series is part of a bigger topic to support Partial-IO on am62,
am62a and am62p. Partial-IO is a poweroff state in which some pins are
able to wakeup the SoC. In detail MCU m_can and two serial port pins can
trigger the wakeup.

These two other series are relevant for the support of Partial-IO:

 - firmware: ti_sci: Partial-IO support
 - serial: 8250: omap: Add am62 wakeup support

A test branch is available here that includes all patches required to
test Partial-IO:

https://gitlab.baylibre.com/msp8/linux/-/tree/integration/am62-lp-sk-partialio/v6.9?ref_type=heads

After enabling Wake-on-LAN the system can be powered off and will enter
the Partial-IO state in which it can be woken up by activity on the
specific pins:
    ethtool -s can0 wol p
    ethtool -s can1 wol p
    poweroff

I tested these patches on am62-lp-sk.

Best,
Markus

Markus Schneider-Pargmann (6):
  dt-bindings: can: m_can: Add wakeup-source property
  dt-bindings: can: m_can: Add wakeup pinctrl state
  can: m_can: Map WoL to device_set_wakeup_enable
  can: m_can: Support pinctrl wakeup state
  arm64: dts: ti: k3-am62: Mark mcu_mcan0/1 as wakeup-source
  arm64: dts: ti: k3-am62a-mcu: Mark mcu_mcan0/1 as wakeup-source

Vibhore Vardhan (1):
  arm64: dts: ti: k3-am62p-mcu: Mark mcu_mcan0/1 as wakeup-source

 .../bindings/net/can/bosch,m_can.yaml         | 20 +++++++++
 arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi       |  2 +
 arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi      |  2 +
 arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi      |  2 +
 drivers/net/can/m_can/m_can.c                 | 43 +++++++++++++++++++
 drivers/net/can/m_can/m_can.h                 |  4 ++
 6 files changed, 73 insertions(+)

-- 
2.43.0