[PATCH v6 0/5] Marvell HW overlay support for Cadence xSPI

[PATCH v6 0/5] Marvell HW overlay support for Cadence xSPI

[Witold Sadowski]

This patch series adds support for the second version of the Marvell
hardware overlay for the Cadence xSPI IP block. The overlay is a hardware
change made around the original xSPI block. It extends xSPI features with
clock configuration, interrupt masking, and full-duplex, variable-length SPI
operations.

These functionalities allow the xSPI block to operate not only with memory
devices but also with simple SPI devices and TPM devices.

Changes:
v6:
  Fix item order in cdns,xspi.yaml

v5:
  Rework cdns,xspi.yaml file
  Reword commit messages
  Move mamory mapping to ACPI patch
  Use devm_platform_ioremap_resource instead of two step mapping

v4:
  Rename new Marvell registers to keep naming conventions
  Rename mrvl,xspi-nor to marvell,cnxx,xspi-nor
  Various fixed for cdns,xspi.yaml file:
    - Remove unnecesary parameters
    - Link register xferbase with marvell,cn10-xspi-nor
    - Move default values to .c file from device-tree
  Clock configuration optimization
  ACPI fixes:
    - Remove incorrect ACPI match table
  Added .data field to device_id, fixes for matching in ACPI and dtb case
  Minor style comment changes

v3:
  Removed all kconfig changes
  Added device-tree mrvl,xspi-nor tag

v2:
  Support for second overlay iteration

v1:
  -

v0:
  Initial support for v1 overlay

Piyush Malgujar (1):
  spi: cadence: Allow to read basic xSPI configuration from ACPI

Witold Sadowski (4):
  spi: cadence: Ensure data lines set to low during dummy-cycle period
  spi: dt-bindings: cadence: Add Marvell overlay bindings documentation
    for Cadence XSPI
  spi: cadence: Add Marvell xSPI IP overlay changes
  spi: cadence: Add MRVL overlay xfer operation support

 .../devicetree/bindings/spi/cdns,xspi.yaml    |  32 +-
 drivers/spi/spi-cadence-xspi.c                | 620 +++++++++++++++++-
 2 files changed, 628 insertions(+), 24 deletions(-)

-- 
2.43.0

[PATCH v6 1/5] spi: cadence: Ensure data lines set to low during dummy-cycle period

[Witold Sadowski]

During dummy-cycles xSPI will switch GPIO into Hi-Z mode. In that dummy
period voltage on data lines will slowly drop, what can cause
unintentional modebyte transmission. Value send to SPI memory chip will
depend on last address, and clock frequency.
To prevent unforeseen consequences of that behaviour, force send
single modebyte(0x00).
Modebyte will be send only if number of dummy-cycles is not equal
to 0. Code must also reduce dummycycle byte count by one - as one byte
is send as modebyte.

Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
---
 drivers/spi/spi-cadence-xspi.c | 20 +++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/drivers/spi/spi-cadence-xspi.c b/drivers/spi/spi-cadence-xspi.c
index 8648b8eb080d..cdce2e280f66 100644
--- a/drivers/spi/spi-cadence-xspi.c
+++ b/drivers/spi/spi-cadence-xspi.c
@@ -145,6 +145,9 @@
 #define CDNS_XSPI_STIG_DONE_FLAG		BIT(0)
 #define CDNS_XSPI_TRD_STATUS			0x0104
 
+#define MODE_NO_OF_BYTES			GENMASK(25, 24)
+#define MODEBYTES_COUNT			1
+
 /* Helper macros for filling command registers */
 #define CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_1(op, data_phase) ( \
 	FIELD_PREP(CDNS_XSPI_CMD_INSTR_TYPE, (data_phase) ? \
@@ -157,9 +160,10 @@
 	FIELD_PREP(CDNS_XSPI_CMD_P1_R2_ADDR3, ((op)->addr.val >> 24) & 0xFF) | \
 	FIELD_PREP(CDNS_XSPI_CMD_P1_R2_ADDR4, ((op)->addr.val >> 32) & 0xFF))
 
-#define CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_3(op) ( \
+#define CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_3(op, modebytes) ( \
 	FIELD_PREP(CDNS_XSPI_CMD_P1_R3_ADDR5, ((op)->addr.val >> 40) & 0xFF) | \
 	FIELD_PREP(CDNS_XSPI_CMD_P1_R3_CMD, (op)->cmd.opcode) | \
+	FIELD_PREP(MODE_NO_OF_BYTES, modebytes) | \
 	FIELD_PREP(CDNS_XSPI_CMD_P1_R3_NUM_ADDR_BYTES, (op)->addr.nbytes))
 
 #define CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_4(op, chipsel) ( \
@@ -173,12 +177,12 @@
 #define CDNS_XSPI_CMD_FLD_DSEQ_CMD_2(op) \
 	FIELD_PREP(CDNS_XSPI_CMD_DSEQ_R2_DCNT_L, (op)->data.nbytes & 0xFFFF)
 
-#define CDNS_XSPI_CMD_FLD_DSEQ_CMD_3(op) ( \
+#define CDNS_XSPI_CMD_FLD_DSEQ_CMD_3(op, dummybytes) ( \
 	FIELD_PREP(CDNS_XSPI_CMD_DSEQ_R3_DCNT_H, \
 		((op)->data.nbytes >> 16) & 0xffff) | \
 	FIELD_PREP(CDNS_XSPI_CMD_DSEQ_R3_NUM_OF_DUMMY, \
 		  (op)->dummy.buswidth != 0 ? \
-		  (((op)->dummy.nbytes * 8) / (op)->dummy.buswidth) : \
+		  (((dummybytes) * 8) / (op)->dummy.buswidth) : \
 		  0))
 
 #define CDNS_XSPI_CMD_FLD_DSEQ_CMD_4(op, chipsel) ( \
@@ -351,6 +355,7 @@ static int cdns_xspi_send_stig_command(struct cdns_xspi_dev *cdns_xspi,
 	u32 cmd_regs[6];
 	u32 cmd_status;
 	int ret;
+	int dummybytes = op->dummy.nbytes;
 
 	ret = cdns_xspi_wait_for_controller_idle(cdns_xspi);
 	if (ret < 0)
@@ -365,7 +370,12 @@ static int cdns_xspi_send_stig_command(struct cdns_xspi_dev *cdns_xspi,
 	memset(cmd_regs, 0, sizeof(cmd_regs));
 	cmd_regs[1] = CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_1(op, data_phase);
 	cmd_regs[2] = CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_2(op);
-	cmd_regs[3] = CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_3(op);
+	if (dummybytes != 0) {
+		cmd_regs[3] = CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_3(op, 1);
+		dummybytes--;
+	} else {
+		cmd_regs[3] = CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_3(op, 0);
+	}
 	cmd_regs[4] = CDNS_XSPI_CMD_FLD_P1_INSTR_CMD_4(op,
 						       cdns_xspi->cur_cs);
 
@@ -375,7 +385,7 @@ static int cdns_xspi_send_stig_command(struct cdns_xspi_dev *cdns_xspi,
 		cmd_regs[0] = CDNS_XSPI_STIG_DONE_FLAG;
 		cmd_regs[1] = CDNS_XSPI_CMD_FLD_DSEQ_CMD_1(op);
 		cmd_regs[2] = CDNS_XSPI_CMD_FLD_DSEQ_CMD_2(op);
-		cmd_regs[3] = CDNS_XSPI_CMD_FLD_DSEQ_CMD_3(op);
+		cmd_regs[3] = CDNS_XSPI_CMD_FLD_DSEQ_CMD_3(op, dummybytes);
 		cmd_regs[4] = CDNS_XSPI_CMD_FLD_DSEQ_CMD_4(op,
 							   cdns_xspi->cur_cs);
 
-- 
2.43.0

[PATCH v6 2/5] spi: dt-bindings: cadence: Add Marvell overlay bindings documentation for Cadence XSPI

[Witold Sadowski]

Add new bindings for the v2 Marvell xSPI overlay: marvell,cn10-xspi-nor
compatible string. This new compatible string distinguishes between the
original and modified xSPI block.

Also add an optional base for the xfer register set with an additional
reg field to allocate the xSPI Marvell overlay XFER block.

Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
---
 .../devicetree/bindings/spi/cdns,xspi.yaml    | 32 ++++++++++++++++---
 1 file changed, 28 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/spi/cdns,xspi.yaml b/Documentation/devicetree/bindings/spi/cdns,xspi.yaml
index eb0f92468185..49c6a2c82fc4 100644
--- a/Documentation/devicetree/bindings/spi/cdns,xspi.yaml
+++ b/Documentation/devicetree/bindings/spi/cdns,xspi.yaml
@@ -15,24 +15,27 @@ description: |
   single, dual, quad or octal wire transmission modes for
   read/write access to slaves such as SPI-NOR flash.
 
-allOf:
-  - $ref: spi-controller.yaml#
-
 properties:
   compatible:
-    const: cdns,xspi-nor
+    enum:
+      - cdns,xspi-nor
+      - marvell,cn10-xspi-nor
 
   reg:
     items:
       - description: address and length of the controller register set
       - description: address and length of the Slave DMA data port
       - description: address and length of the auxiliary registers
+      - description: address and length of the xfer registers
+    minItems: 3
 
   reg-names:
     items:
       - const: io
       - const: sdma
       - const: aux
+      - const: xferbase
+    minItems: 3
 
   interrupts:
     maxItems: 1
@@ -42,6 +45,27 @@ required:
   - reg
   - interrupts
 
+allOf:
+  - $ref: spi-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - marvell,cn10-xspi-nor
+    then:
+      properties:
+        reg:
+          minItems: 4
+        reg-names:
+          minItems: 4
+    else:
+      properties:
+        reg:
+          maxItems: 3
+        reg-names:
+          maxItems: 3
+
 unevaluatedProperties: false
 
 examples:
-- 
2.43.0

Re: [PATCH v6 2/5] spi: dt-bindings: cadence: Add Marvell overlay bindings documentation for Cadence XSPI

[Krzysztof Kozlowski]

On 29/05/2024 09:40, Witold Sadowski wrote:
> Add new bindings for the v2 Marvell xSPI overlay: marvell,cn10-xspi-nor
> compatible string. This new compatible string distinguishes between the
> original and modified xSPI block.
> 
> Also add an optional base for the xfer register set with an additional
> reg field to allocate the xSPI Marvell overlay XFER block.
> 
> Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
> ---

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

[PATCH v6 3/5] spi: cadence: Add Marvell xSPI IP overlay changes

[Witold Sadowski]

This commit adds support for the basic v2 Marvell overlay block. Key
features included are:
    - Clock configuration
    - PHY configuration
    - Interrupt configuration (enabling)

The clock divider block, built on top of the Cadence xSPI IP,
divides an external 800MHz clock. It supports a limited range of clock
speeds from 6.25MHz to 200MHz.

To manage interrupts correctly, the driver needs to clear both the MSI-X
interrupt bit and the xSPI interrupt bit. Additionally, interrupt
masking must be disabled.

Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
---
 drivers/spi/spi-cadence-xspi.c | 265 ++++++++++++++++++++++++++++++++-
 1 file changed, 260 insertions(+), 5 deletions(-)

diff --git a/drivers/spi/spi-cadence-xspi.c b/drivers/spi/spi-cadence-xspi.c
index cdce2e280f66..3ba0269f1cc3 100644
--- a/drivers/spi/spi-cadence-xspi.c
+++ b/drivers/spi/spi-cadence-xspi.c
@@ -193,6 +193,43 @@
 		((op)->data.dir == SPI_MEM_DATA_IN) ? \
 		CDNS_XSPI_STIG_CMD_DIR_READ : CDNS_XSPI_STIG_CMD_DIR_WRITE))
 
+/* PHY default values */
+#define REGS_DLL_PHY_CTRL		0x00000707
+#define CTB_RFILE_PHY_CTRL		0x00004000
+#define RFILE_PHY_TSEL			0x00000000
+#define RFILE_PHY_DQ_TIMING		0x00000101
+#define RFILE_PHY_DQS_TIMING		0x00700404
+#define RFILE_PHY_GATE_LPBK_CTRL	0x00200030
+#define RFILE_PHY_DLL_MASTER_CTRL	0x00800000
+#define RFILE_PHY_DLL_SLAVE_CTRL	0x0000ff01
+
+/* PHY config registers */
+#define CDNS_XSPI_RF_MINICTRL_REGS_DLL_PHY_CTRL			0x1034
+#define CDNS_XSPI_PHY_CTB_RFILE_PHY_CTRL			0x0080
+#define CDNS_XSPI_PHY_CTB_RFILE_PHY_TSEL			0x0084
+#define CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_DQ_TIMING		0x0000
+#define CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_DQS_TIMING		0x0004
+#define CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_GATE_LPBK_CTRL	0x0008
+#define CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_DLL_MASTER_CTRL	0x000c
+#define CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_DLL_SLAVE_CTRL	0x0010
+#define CDNS_XSPI_DATASLICE_RFILE_PHY_DLL_OBS_REG_0		0x001c
+
+#define CDNS_XSPI_DLL_RST_N BIT(24)
+#define CDNS_XSPI_DLL_LOCK  BIT(0)
+
+/* Marvell overlay registers - clock */
+#define MRVL_XSPI_CLK_CTRL_AUX_REG   0x2020
+#define MRVL_XSPI_CLK_ENABLE	     BIT(0)
+#define MRVL_XSPI_CLK_DIV	     GENMASK(4, 1)
+#define MRVL_XSPI_IRQ_ENABLE	     BIT(6)
+#define MRVL_XSPI_CLOCK_IO_HZ	     800000000
+#define MRVL_XSPI_CLOCK_DIVIDED(div) ((MRVL_XSPI_CLOCK_IO_HZ) / (div))
+#define MRVL_DEFAULT_CLK	     25000000
+
+/* Marvell overlay registers - MSI-X */
+#define MRVL_XSPI_SPIX_INTR_AUX	0x2000
+#define MRVL_MSIX_CLEAR_IRQ	0x01
+
 enum cdns_xspi_stig_instr_type {
 	CDNS_XSPI_STIG_INSTR_TYPE_0,
 	CDNS_XSPI_STIG_INSTR_TYPE_1,
@@ -212,6 +249,7 @@ enum cdns_xspi_stig_cmd_dir {
 struct cdns_xspi_dev {
 	struct platform_device *pdev;
 	struct device *dev;
+	bool mrvl_hw_overlay;
 
 	void __iomem *iobase;
 	void __iomem *auxbase;
@@ -232,6 +270,118 @@ struct cdns_xspi_dev {
 	u8 hw_num_banks;
 };
 
+struct cdns_xspi_driver_data {
+	bool mrvl_hw_overlay;
+};
+
+static struct cdns_xspi_driver_data mrvl_driver_data = {
+	.mrvl_hw_overlay = true,
+};
+
+static struct cdns_xspi_driver_data cdns_driver_data = {
+	.mrvl_hw_overlay = false,
+};
+
+const int cdns_mrvl_xspi_clk_div_list[] = {
+	4,	//0x0 = Divide by 4.   SPI clock is 200 MHz.
+	6,	//0x1 = Divide by 6.   SPI clock is 133.33 MHz.
+	8,	//0x2 = Divide by 8.   SPI clock is 100 MHz.
+	10,	//0x3 = Divide by 10.  SPI clock is 80 MHz.
+	12,	//0x4 = Divide by 12.  SPI clock is 66.666 MHz.
+	16,	//0x5 = Divide by 16.  SPI clock is 50 MHz.
+	18,	//0x6 = Divide by 18.  SPI clock is 44.44 MHz.
+	20,	//0x7 = Divide by 20.  SPI clock is 40 MHz.
+	24,	//0x8 = Divide by 24.  SPI clock is 33.33 MHz.
+	32,	//0x9 = Divide by 32.  SPI clock is 25 MHz.
+	40,	//0xA = Divide by 40.  SPI clock is 20 MHz.
+	50,	//0xB = Divide by 50.  SPI clock is 16 MHz.
+	64,	//0xC = Divide by 64.  SPI clock is 12.5 MHz.
+	128	//0xD = Divide by 128. SPI clock is 6.25 MHz.
+};
+
+static bool cdns_xspi_reset_dll(struct cdns_xspi_dev *cdns_xspi)
+{
+	u32 dll_cntrl = readl(cdns_xspi->iobase +
+			      CDNS_XSPI_RF_MINICTRL_REGS_DLL_PHY_CTRL);
+	u32 dll_lock;
+
+	/* Reset DLL */
+	dll_cntrl |= CDNS_XSPI_DLL_RST_N;
+	writel(dll_cntrl, cdns_xspi->iobase +
+			  CDNS_XSPI_RF_MINICTRL_REGS_DLL_PHY_CTRL);
+
+	/* Wait for DLL lock */
+	return readl_relaxed_poll_timeout(cdns_xspi->iobase +
+		CDNS_XSPI_INTR_STATUS_REG,
+		dll_lock, ((dll_lock & CDNS_XSPI_DLL_LOCK) == 1), 10, 10000);
+}
+
+/* Static configuration of PHY */
+static bool cdns_xspi_configure_phy(struct cdns_xspi_dev *cdns_xspi)
+{
+	writel(REGS_DLL_PHY_CTRL,
+	       cdns_xspi->iobase + CDNS_XSPI_RF_MINICTRL_REGS_DLL_PHY_CTRL);
+	writel(CTB_RFILE_PHY_CTRL,
+	       cdns_xspi->auxbase + CDNS_XSPI_PHY_CTB_RFILE_PHY_CTRL);
+	writel(RFILE_PHY_TSEL,
+	       cdns_xspi->auxbase + CDNS_XSPI_PHY_CTB_RFILE_PHY_TSEL);
+	writel(RFILE_PHY_DQ_TIMING,
+	       cdns_xspi->auxbase + CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_DQ_TIMING);
+	writel(RFILE_PHY_DQS_TIMING,
+	       cdns_xspi->auxbase + CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_DQS_TIMING);
+	writel(RFILE_PHY_GATE_LPBK_CTRL,
+	       cdns_xspi->auxbase + CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_GATE_LPBK_CTRL);
+	writel(RFILE_PHY_DLL_MASTER_CTRL,
+	       cdns_xspi->auxbase + CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_DLL_MASTER_CTRL);
+	writel(RFILE_PHY_DLL_SLAVE_CTRL,
+	       cdns_xspi->auxbase + CDNS_XSPI_PHY_DATASLICE_RFILE_PHY_DLL_SLAVE_CTRL);
+
+	return cdns_xspi_reset_dll(cdns_xspi);
+}
+
+/* Find max avalible clock */
+static bool cdns_mrvl_xspi_setup_clock(struct cdns_xspi_dev *cdns_xspi,
+				       int requested_clk)
+{
+	int i = 0;
+	int clk_val;
+	u32 clk_reg;
+	bool update_clk = false;
+
+	while (i < ARRAY_SIZE(cdns_mrvl_xspi_clk_div_list)) {
+		clk_val = MRVL_XSPI_CLOCK_DIVIDED(
+				cdns_mrvl_xspi_clk_div_list[i]);
+		if (clk_val <= requested_clk)
+			break;
+		i++;
+	}
+
+	dev_dbg(cdns_xspi->dev, "Found clk div: %d, clk val: %d\n",
+		cdns_mrvl_xspi_clk_div_list[i],
+		MRVL_XSPI_CLOCK_DIVIDED(
+		cdns_mrvl_xspi_clk_div_list[i]));
+
+	clk_reg = readl(cdns_xspi->auxbase + MRVL_XSPI_CLK_CTRL_AUX_REG);
+
+	if (FIELD_GET(MRVL_XSPI_CLK_DIV, clk_reg) != i) {
+		clk_reg &= ~MRVL_XSPI_CLK_ENABLE;
+		writel(clk_reg,
+		       cdns_xspi->auxbase + MRVL_XSPI_CLK_CTRL_AUX_REG);
+		clk_reg = FIELD_PREP(MRVL_XSPI_CLK_DIV, i);
+		clk_reg &= ~MRVL_XSPI_CLK_DIV;
+		clk_reg |= FIELD_PREP(MRVL_XSPI_CLK_DIV, i);
+		clk_reg |= MRVL_XSPI_CLK_ENABLE;
+		clk_reg |= MRVL_XSPI_IRQ_ENABLE;
+		update_clk = true;
+	}
+
+	if (update_clk)
+		writel(clk_reg,
+		       cdns_xspi->auxbase + MRVL_XSPI_CLK_CTRL_AUX_REG);
+
+	return update_clk;
+}
+
 static int cdns_xspi_wait_for_controller_idle(struct cdns_xspi_dev *cdns_xspi)
 {
 	u32 ctrl_stat;
@@ -295,6 +445,10 @@ static void cdns_xspi_set_interrupts(struct cdns_xspi_dev *cdns_xspi,
 				     bool enabled)
 {
 	u32 intr_enable;
+	u32 irq_status;
+
+	irq_status = readl(cdns_xspi->iobase + CDNS_XSPI_INTR_STATUS_REG);
+	writel(irq_status, cdns_xspi->iobase + CDNS_XSPI_INTR_STATUS_REG);
 
 	intr_enable = readl(cdns_xspi->iobase + CDNS_XSPI_INTR_ENABLE_REG);
 	if (enabled)
@@ -319,6 +473,9 @@ static int cdns_xspi_controller_init(struct cdns_xspi_dev *cdns_xspi)
 		return -EIO;
 	}
 
+	writel(FIELD_PREP(CDNS_XSPI_CTRL_WORK_MODE, CDNS_XSPI_WORK_MODE_STIG),
+	       cdns_xspi->iobase + CDNS_XSPI_CTRL_CONFIG_REG);
+
 	ctrl_features = readl(cdns_xspi->iobase + CDNS_XSPI_CTRL_FEATURES_REG);
 	cdns_xspi->hw_num_banks = FIELD_GET(CDNS_XSPI_NUM_BANKS, ctrl_features);
 	cdns_xspi_set_interrupts(cdns_xspi, false);
@@ -326,6 +483,70 @@ static int cdns_xspi_controller_init(struct cdns_xspi_dev *cdns_xspi)
 	return 0;
 }
 
+static void mrvl_ioreadq(void __iomem  *addr, void *buf, int len)
+{
+	int i = 0;
+	int rcount = len / 8;
+	int rcount_nf = len % 8;
+	uint64_t tmp;
+	uint64_t *buf64 = (uint64_t *)buf;
+
+	if (((uint64_t)buf % 8) == 0) {
+		for (i = 0; i < rcount; i++)
+			*buf64++ = readq(addr);
+	} else {
+		for (i = 0; i < rcount; i++) {
+			tmp = readq(addr);
+			memcpy(buf+(i*8), &tmp, 8);
+		}
+	}
+
+	if (rcount_nf != 0) {
+		tmp = readq(addr);
+		memcpy(buf+(i*8), &tmp, rcount_nf);
+	}
+}
+
+static void mrvl_iowriteq(void __iomem *addr, const void *buf, int len)
+{
+	int i = 0;
+	int rcount = len / 8;
+	int rcount_nf = len % 8;
+	uint64_t tmp;
+	uint64_t *buf64 = (uint64_t *)buf;
+
+	if (((uint64_t)buf % 8) == 0) {
+		for (i = 0; i < rcount; i++)
+			writeq(*buf64++, addr);
+	} else {
+		for (i = 0; i < rcount; i++) {
+			memcpy(&tmp, buf+(i*8), 8);
+			writeq(tmp, addr);
+		}
+	}
+
+	if (rcount_nf != 0) {
+		memcpy(&tmp, buf+(i*8), rcount_nf);
+		writeq(tmp, addr);
+	}
+}
+
+static void cdns_xspi_sdma_memread(struct cdns_xspi_dev *cdns_xspi, int len)
+{
+	if (cdns_xspi->mrvl_hw_overlay)
+		mrvl_ioreadq(cdns_xspi->sdmabase, cdns_xspi->in_buffer, len);
+	else
+		ioread8_rep(cdns_xspi->sdmabase, cdns_xspi->in_buffer, len);
+}
+
+static void cdns_xspi_sdma_memwrite(struct cdns_xspi_dev *cdns_xspi, int len)
+{
+	if (cdns_xspi->mrvl_hw_overlay)
+		mrvl_iowriteq(cdns_xspi->sdmabase, cdns_xspi->out_buffer, len);
+	else
+		iowrite8_rep(cdns_xspi->sdmabase, cdns_xspi->out_buffer, len);
+}
+
 static void cdns_xspi_sdma_handle(struct cdns_xspi_dev *cdns_xspi)
 {
 	u32 sdma_size, sdma_trd_info;
@@ -337,13 +558,11 @@ static void cdns_xspi_sdma_handle(struct cdns_xspi_dev *cdns_xspi)
 
 	switch (sdma_dir) {
 	case CDNS_XSPI_SDMA_DIR_READ:
-		ioread8_rep(cdns_xspi->sdmabase,
-			    cdns_xspi->in_buffer, sdma_size);
+		cdns_xspi_sdma_memread(cdns_xspi, sdma_size);
 		break;
 
 	case CDNS_XSPI_SDMA_DIR_WRITE:
-		iowrite8_rep(cdns_xspi->sdmabase,
-			     cdns_xspi->out_buffer, sdma_size);
+		cdns_xspi_sdma_memwrite(cdns_xspi, sdma_size);
 		break;
 	}
 }
@@ -421,6 +640,9 @@ static int cdns_xspi_mem_op(struct cdns_xspi_dev *cdns_xspi,
 	if (cdns_xspi->cur_cs != spi_get_chipselect(mem->spi, 0))
 		cdns_xspi->cur_cs = spi_get_chipselect(mem->spi, 0);
 
+	if (cdns_xspi->mrvl_hw_overlay)
+		cdns_mrvl_xspi_setup_clock(cdns_xspi, mem->spi->max_speed_hz);
+
 	return cdns_xspi_send_stig_command(cdns_xspi, op,
 					   (dir != SPI_MEM_NO_DATA));
 }
@@ -461,6 +683,10 @@ static irqreturn_t cdns_xspi_irq_handler(int this_irq, void *dev)
 	irq_status = readl(cdns_xspi->iobase + CDNS_XSPI_INTR_STATUS_REG);
 	writel(irq_status, cdns_xspi->iobase + CDNS_XSPI_INTR_STATUS_REG);
 
+	if (cdns_xspi->mrvl_hw_overlay)
+		writel(MRVL_MSIX_CLEAR_IRQ,
+		       cdns_xspi->auxbase + MRVL_XSPI_SPIX_INTR_AUX);
+
 	if (irq_status &
 	    (CDNS_XSPI_SDMA_ERROR | CDNS_XSPI_SDMA_TRIGGER |
 	     CDNS_XSPI_STIG_DONE)) {
@@ -534,11 +760,23 @@ static void cdns_xspi_print_phy_config(struct cdns_xspi_dev *cdns_xspi)
 		 readl(cdns_xspi->auxbase + CDNS_XSPI_CCP_PHY_DLL_SLAVE_CTRL));
 }
 
+static int cdns_xspi_setup(struct spi_device *spi_dev)
+{
+	struct cdns_xspi_dev *cdns_xspi = spi_controller_get_devdata(
+						spi_dev->controller);
+
+	if (cdns_xspi->mrvl_hw_overlay)
+		cdns_mrvl_xspi_setup_clock(cdns_xspi, spi_dev->max_speed_hz);
+
+	return 0;
+}
+
 static int cdns_xspi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct spi_controller *host = NULL;
 	struct cdns_xspi_dev *cdns_xspi = NULL;
+	const struct cdns_xspi_driver_data *drv_data;
 	struct resource *res;
 	int ret;
 
@@ -550,10 +788,16 @@ static int cdns_xspi_probe(struct platform_device *pdev)
 		SPI_RX_DUAL | SPI_RX_QUAD | SPI_TX_OCTAL | SPI_RX_OCTAL |
 		SPI_MODE_0  | SPI_MODE_3;
 
+	drv_data = of_device_get_match_data(dev);
+
 	host->mem_ops = &cadence_xspi_mem_ops;
 	host->dev.of_node = pdev->dev.of_node;
+	host->dev.fwnode = pdev->dev.fwnode;
 	host->bus_num = -1;
 
+	if (drv_data->mrvl_hw_overlay)
+		host->setup = cdns_xspi_setup;
+
 	platform_set_drvdata(pdev, host);
 
 	cdns_xspi = spi_controller_get_devdata(host);
@@ -565,6 +809,8 @@ static int cdns_xspi_probe(struct platform_device *pdev)
 	init_completion(&cdns_xspi->auto_cmd_complete);
 	init_completion(&cdns_xspi->sdma_complete);
 
+	cdns_xspi->mrvl_hw_overlay = drv_data->mrvl_hw_overlay;
+
 	ret = cdns_xspi_of_get_plat_data(pdev);
 	if (ret)
 		return -ENODEV;
@@ -598,8 +844,12 @@ static int cdns_xspi_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	cdns_xspi_print_phy_config(cdns_xspi);
+	if (drv_data->mrvl_hw_overlay) {
+		cdns_mrvl_xspi_setup_clock(cdns_xspi, MRVL_DEFAULT_CLK);
+		cdns_xspi_configure_phy(cdns_xspi);
+	}
 
+	cdns_xspi_print_phy_config(cdns_xspi);
 	ret = cdns_xspi_controller_init(cdns_xspi);
 	if (ret) {
 		dev_err(dev, "Failed to initialize controller\n");
@@ -622,6 +872,11 @@ static int cdns_xspi_probe(struct platform_device *pdev)
 static const struct of_device_id cdns_xspi_of_match[] = {
 	{
 		.compatible = "cdns,xspi-nor",
+		.data = &cdns_driver_data,
+	},
+	{
+		.compatible = "marvell,cn10-xspi-nor",
+		.data = &mrvl_driver_data,
 	},
 	{ /* end of table */}
 };
-- 
2.43.0

[PATCH v6 4/5] spi: cadence: Allow to read basic xSPI configuration from ACPI

[Witold Sadowski]

From: Piyush Malgujar <pmalgujar@marvell.com>

These changes enable reading the configurations from ACPI tables as
required for successful probing in an ACPI UEFI environment. In the
case of an ACPI-disabled or DTS-based environment, it will continue
to read configurations from DTS as before.

Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
---
 drivers/spi/spi-cadence-xspi.c | 90 ++++++++++++++++++++++++++++++----
 1 file changed, 80 insertions(+), 10 deletions(-)

diff --git a/drivers/spi/spi-cadence-xspi.c b/drivers/spi/spi-cadence-xspi.c
index 3ba0269f1cc3..490bba7a0fc8 100644
--- a/drivers/spi/spi-cadence-xspi.c
+++ b/drivers/spi/spi-cadence-xspi.c
@@ -2,6 +2,7 @@
 // Cadence XSPI flash controller driver
 // Copyright (C) 2020-21 Cadence
 
+#include <linux/acpi.h>
 #include <linux/completion.h>
 #include <linux/delay.h>
 #include <linux/err.h>
@@ -14,6 +15,7 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
+#include <linux/property.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/spi-mem.h>
 #include <linux/bitfield.h>
@@ -647,6 +649,67 @@ static int cdns_xspi_mem_op(struct cdns_xspi_dev *cdns_xspi,
 					   (dir != SPI_MEM_NO_DATA));
 }
 
+#ifdef CONFIG_ACPI
+static bool cdns_xspi_supports_op(struct spi_mem *mem,
+				  const struct spi_mem_op *op)
+{
+	struct spi_device *spi = mem->spi;
+	const union acpi_object *obj;
+	struct acpi_device *adev;
+
+	adev = ACPI_COMPANION(&spi->dev);
+
+	if (!acpi_dev_get_property(adev, "spi-tx-bus-width", ACPI_TYPE_INTEGER,
+				   &obj)) {
+		switch (obj->integer.value) {
+		case 1:
+			break;
+		case 2:
+			spi->mode |= SPI_TX_DUAL;
+			break;
+		case 4:
+			spi->mode |= SPI_TX_QUAD;
+			break;
+		case 8:
+			spi->mode |= SPI_TX_OCTAL;
+			break;
+		default:
+			dev_warn(&spi->dev,
+				 "spi-tx-bus-width %lld not supported\n",
+				 obj->integer.value);
+			break;
+		}
+	}
+
+	if (!acpi_dev_get_property(adev, "spi-rx-bus-width", ACPI_TYPE_INTEGER,
+				   &obj)) {
+		switch (obj->integer.value) {
+		case 1:
+			break;
+		case 2:
+			spi->mode |= SPI_RX_DUAL;
+			break;
+		case 4:
+			spi->mode |= SPI_RX_QUAD;
+			break;
+		case 8:
+			spi->mode |= SPI_RX_OCTAL;
+			break;
+		default:
+			dev_warn(&spi->dev,
+				 "spi-rx-bus-width %lld not supported\n",
+				 obj->integer.value);
+			break;
+		}
+	}
+
+	if (!spi_mem_default_supports_op(mem, op))
+		return false;
+
+	return true;
+}
+#endif
+
 static int cdns_xspi_mem_op_execute(struct spi_mem *mem,
 				    const struct spi_mem_op *op)
 {
@@ -670,6 +733,9 @@ static int cdns_xspi_adjust_mem_op_size(struct spi_mem *mem, struct spi_mem_op *
 }
 
 static const struct spi_controller_mem_ops cadence_xspi_mem_ops = {
+#ifdef CONFIG_ACPI
+	.supports_op = cdns_xspi_supports_op,
+#endif
 	.exec_op = cdns_xspi_mem_op_execute,
 	.adjust_op_size = cdns_xspi_adjust_mem_op_size,
 };
@@ -721,21 +787,20 @@ static irqreturn_t cdns_xspi_irq_handler(int this_irq, void *dev)
 
 static int cdns_xspi_of_get_plat_data(struct platform_device *pdev)
 {
-	struct device_node *node_prop = pdev->dev.of_node;
-	struct device_node *node_child;
+	struct fwnode_handle *fwnode_child;
 	unsigned int cs;
 
-	for_each_child_of_node(node_prop, node_child) {
-		if (!of_device_is_available(node_child))
+	device_for_each_child_node(&pdev->dev, fwnode_child) {
+		if (!fwnode_device_is_available(fwnode_child))
 			continue;
 
-		if (of_property_read_u32(node_child, "reg", &cs)) {
+		if (fwnode_property_read_u32(fwnode_child, "reg", &cs)) {
 			dev_err(&pdev->dev, "Couldn't get memory chip select\n");
-			of_node_put(node_child);
+			fwnode_handle_put(fwnode_child);
 			return -ENXIO;
 		} else if (cs >= CDNS_XSPI_MAX_BANKS) {
 			dev_err(&pdev->dev, "reg (cs) parameter value too large\n");
-			of_node_put(node_child);
+			fwnode_handle_put(fwnode_child);
 			return -ENXIO;
 		}
 	}
@@ -789,6 +854,11 @@ static int cdns_xspi_probe(struct platform_device *pdev)
 		SPI_MODE_0  | SPI_MODE_3;
 
 	drv_data = of_device_get_match_data(dev);
+	if (!drv_data) {
+		drv_data = acpi_device_get_match_data(dev);
+		if (!drv_data)
+			return -ENODEV;
+	}
 
 	host->mem_ops = &cadence_xspi_mem_ops;
 	host->dev.of_node = pdev->dev.of_node;
@@ -815,19 +885,19 @@ static int cdns_xspi_probe(struct platform_device *pdev)
 	if (ret)
 		return -ENODEV;
 
-	cdns_xspi->iobase = devm_platform_ioremap_resource_byname(pdev, "io");
+	cdns_xspi->iobase = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(cdns_xspi->iobase)) {
 		dev_err(dev, "Failed to remap controller base address\n");
 		return PTR_ERR(cdns_xspi->iobase);
 	}
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "sdma");
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 	cdns_xspi->sdmabase = devm_ioremap_resource(dev, res);
 	if (IS_ERR(cdns_xspi->sdmabase))
 		return PTR_ERR(cdns_xspi->sdmabase);
 	cdns_xspi->sdmasize = resource_size(res);
 
-	cdns_xspi->auxbase = devm_platform_ioremap_resource_byname(pdev, "aux");
+	cdns_xspi->auxbase = devm_platform_ioremap_resource(pdev, 2);
 	if (IS_ERR(cdns_xspi->auxbase)) {
 		dev_err(dev, "Failed to remap AUX address\n");
 		return PTR_ERR(cdns_xspi->auxbase);
-- 
2.43.0

[PATCH v6 5/5] spi: cadence: Add MRVL overlay xfer operation support

[Witold Sadowski]

MRVL Xfer overlay extends xSPI capabilities to support non-memory SPI
operations. The Marvell overlay, combined with a generic command, allows
for full-duplex SPI transactions. It also enables transactions with
undetermined lengths using the cs_hold parameter and the ability to
extend CS signal assertion, even if the xSPI block requests CS signal
de-assertion.

Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
---
 drivers/spi/spi-cadence-xspi.c | 245 +++++++++++++++++++++++++++++++++
 1 file changed, 245 insertions(+)

diff --git a/drivers/spi/spi-cadence-xspi.c b/drivers/spi/spi-cadence-xspi.c
index 490bba7a0fc8..7279a73162ce 100644
--- a/drivers/spi/spi-cadence-xspi.c
+++ b/drivers/spi/spi-cadence-xspi.c
@@ -219,6 +219,7 @@
 #define CDNS_XSPI_DLL_RST_N BIT(24)
 #define CDNS_XSPI_DLL_LOCK  BIT(0)
 
+
 /* Marvell overlay registers - clock */
 #define MRVL_XSPI_CLK_CTRL_AUX_REG   0x2020
 #define MRVL_XSPI_CLK_ENABLE	     BIT(0)
@@ -232,6 +233,22 @@
 #define MRVL_XSPI_SPIX_INTR_AUX	0x2000
 #define MRVL_MSIX_CLEAR_IRQ	0x01
 
+/* Marvell overlay registers - xfer */
+#define MRVL_XFER_FUNC_CTRL		 0x210
+#define MRVL_XFER_FUNC_CTRL_READ_DATA(i) (0x000 + 8 * (i))
+#define MRVL_XFER_SOFT_RESET		 BIT(11)
+#define MRVL_XFER_CS_N_HOLD		 GENMASK(9, 6)
+#define MRVL_XFER_RECEIVE_ENABLE	 BIT(4)
+#define MRVL_XFER_FUNC_ENABLE		 BIT(3)
+#define MRVL_XFER_CLK_CAPTURE_POL	 BIT(2)
+#define MRVL_XFER_CLK_DRIVE_POL		 BIT(1)
+#define MRVL_XFER_FUNC_START		 BIT(0)
+#define MRVL_XFER_QWORD_COUNT		 32
+#define MRVL_XFER_QWORD_BYTECOUNT	 8
+
+#define MRVL_XSPI_POLL_TIMEOUT_US	1000
+#define MRVL_XSPI_POLL_DELAY_US		10
+
 enum cdns_xspi_stig_instr_type {
 	CDNS_XSPI_STIG_INSTR_TYPE_0,
 	CDNS_XSPI_STIG_INSTR_TYPE_1,
@@ -256,6 +273,7 @@ struct cdns_xspi_dev {
 	void __iomem *iobase;
 	void __iomem *auxbase;
 	void __iomem *sdmabase;
+	void __iomem *xferbase;
 
 	int irq;
 	int cur_cs;
@@ -270,6 +288,9 @@ struct cdns_xspi_dev {
 	const void *out_buffer;
 
 	u8 hw_num_banks;
+
+	bool xfer_in_progress;
+	int current_xfer_qword;
 };
 
 struct cdns_xspi_driver_data {
@@ -836,6 +857,220 @@ static int cdns_xspi_setup(struct spi_device *spi_dev)
 	return 0;
 }
 
+static int cdns_xspi_prepare_generic(int cs, const void *dout, int len, int glue, u32 *cmd_regs)
+{
+	u8 *data = (u8 *)dout;
+	int i;
+	int data_counter = 0;
+
+	memset(cmd_regs, 0x00, 6*4);
+
+	if (len > 7) {
+		for (i = (len >= 10 ? 2 : len - 8); i >= 0 ; i--)
+			cmd_regs[3] |= data[data_counter++] << (8*i);
+	}
+	if (len > 3) {
+		for (i = (len >= 7 ? 3 : len - 4); i >= 0; i--)
+			cmd_regs[2] |= data[data_counter++] << (8*i);
+	}
+	for (i = (len >= 3 ? 2 : len - 1); i >= 0 ; i--)
+		cmd_regs[1] |= data[data_counter++] << (8 + 8*i);
+
+	cmd_regs[1] |= 96;
+	cmd_regs[3] |= len << 24;
+	cmd_regs[4] |= cs << 12;
+
+	if (glue == 1)
+		cmd_regs[4] |= 1 << 28;
+
+	return 0;
+}
+
+static unsigned char reverse_bits(unsigned char num)
+{
+	unsigned int count = sizeof(num) * 8 - 1;
+	unsigned int reverse_num = num;
+
+	num >>= 1;
+	while (num) {
+		reverse_num <<= 1;
+		reverse_num |= num & 1;
+		num >>= 1;
+		count--;
+	}
+	reverse_num <<= count;
+	return reverse_num;
+}
+
+static void cdns_xspi_read_single_qword(struct cdns_xspi_dev *cdns_xspi, u8 **buffer)
+{
+	u64 d = readq(cdns_xspi->xferbase +
+		      MRVL_XFER_FUNC_CTRL_READ_DATA(cdns_xspi->current_xfer_qword));
+	u8 *ptr = (u8 *)&d;
+	int k;
+
+	for (k = 0; k < 8; k++) {
+		u8 val = reverse_bits((ptr[k]));
+		**buffer = val;
+		*buffer = *buffer + 1;
+	}
+
+	cdns_xspi->current_xfer_qword++;
+	cdns_xspi->current_xfer_qword %= MRVL_XFER_QWORD_COUNT;
+}
+
+static void cdns_xspi_finish_read(struct cdns_xspi_dev *cdns_xspi, u8 **buffer, u32 data_count)
+{
+	u64 d = readq(cdns_xspi->xferbase +
+		      MRVL_XFER_FUNC_CTRL_READ_DATA(cdns_xspi->current_xfer_qword));
+	u8 *ptr = (u8 *)&d;
+	int k;
+
+	for (k = 0; k < data_count % MRVL_XFER_QWORD_BYTECOUNT; k++) {
+		u8 val = reverse_bits((ptr[k]));
+		**buffer = val;
+		*buffer = *buffer + 1;
+	}
+
+	cdns_xspi->current_xfer_qword++;
+	cdns_xspi->current_xfer_qword %= MRVL_XFER_QWORD_COUNT;
+}
+
+static int cdns_xspi_prepare_transfer(int cs, int dir, int len, u32 *cmd_regs)
+{
+	memset(cmd_regs, 0x00, 6*4);
+
+	cmd_regs[1] |= 127;
+	cmd_regs[2] |= len << 16;
+	cmd_regs[4] |= dir << 4; //dir = 0 read, dir =1 write
+	cmd_regs[4] |= cs << 12;
+
+	return 0;
+}
+
+static bool cdns_xspi_stig_ready(struct cdns_xspi_dev *cdns_xspi, bool sleep)
+{
+	u32 ctrl_stat;
+
+	return readl_relaxed_poll_timeout
+		(cdns_xspi->iobase + CDNS_XSPI_CTRL_STATUS_REG,
+		ctrl_stat,
+		((ctrl_stat & BIT(3)) == 0),
+		sleep ? MRVL_XSPI_POLL_DELAY_US : 0,
+		sleep ? MRVL_XSPI_POLL_TIMEOUT_US : 0);
+}
+
+static bool cdns_xspi_sdma_ready(struct cdns_xspi_dev *cdns_xspi, bool sleep)
+{
+	u32 ctrl_stat;
+
+	return readl_relaxed_poll_timeout
+		(cdns_xspi->iobase + CDNS_XSPI_INTR_STATUS_REG,
+		ctrl_stat,
+		(ctrl_stat & CDNS_XSPI_SDMA_TRIGGER),
+		sleep ? MRVL_XSPI_POLL_DELAY_US : 0,
+		sleep ? MRVL_XSPI_POLL_TIMEOUT_US : 0);
+}
+
+static int cdns_xspi_transfer_one_message_b0(struct spi_controller *controller,
+					   struct spi_message *m)
+{
+	struct cdns_xspi_dev *cdns_xspi = spi_controller_get_devdata(controller);
+	struct spi_device *spi = m->spi;
+	struct spi_transfer *t = NULL;
+
+	const int max_len = MRVL_XFER_QWORD_BYTECOUNT * MRVL_XFER_QWORD_COUNT;
+	int current_cycle_count;
+	int cs = spi_get_chipselect(spi, 0);
+	int cs_change = 0;
+
+	/* Enable xfer state machine */
+	if (!cdns_xspi->xfer_in_progress) {
+		u32 xfer_control = readl(cdns_xspi->xferbase + MRVL_XFER_FUNC_CTRL);
+
+		cdns_xspi->current_xfer_qword = 0;
+		cdns_xspi->xfer_in_progress = true;
+		xfer_control |= (MRVL_XFER_RECEIVE_ENABLE |
+				 MRVL_XFER_CLK_CAPTURE_POL |
+				 MRVL_XFER_FUNC_START |
+				 MRVL_XFER_SOFT_RESET |
+				 FIELD_PREP(MRVL_XFER_CS_N_HOLD, (1 << cs)));
+		xfer_control &= ~(MRVL_XFER_FUNC_ENABLE | MRVL_XFER_CLK_DRIVE_POL);
+		writel(xfer_control, cdns_xspi->xferbase + MRVL_XFER_FUNC_CTRL);
+	}
+
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		u8 *txd = (u8 *) t->tx_buf;
+		u8 *rxd = (u8 *) t->rx_buf;
+		u8 data[10];
+		u32 cmd_regs[6];
+
+		if (!txd)
+			txd = data;
+
+		cdns_xspi->in_buffer = txd + 1;
+		cdns_xspi->out_buffer = txd + 1;
+
+		while (t->len) {
+
+			current_cycle_count = t->len > max_len ? max_len : t->len;
+
+			if (current_cycle_count < 10) {
+				cdns_xspi_prepare_generic(cs, txd, current_cycle_count,
+							  false, cmd_regs);
+				cdns_xspi_trigger_command(cdns_xspi, cmd_regs);
+				if (cdns_xspi_stig_ready(cdns_xspi, true))
+					return -EIO;
+			} else {
+				cdns_xspi_prepare_generic(cs, txd, 1, true, cmd_regs);
+				cdns_xspi_trigger_command(cdns_xspi, cmd_regs);
+				cdns_xspi_prepare_transfer(cs, 1, current_cycle_count - 1,
+							   cmd_regs);
+				cdns_xspi_trigger_command(cdns_xspi, cmd_regs);
+				if (cdns_xspi_sdma_ready(cdns_xspi, true))
+					return -EIO;
+				cdns_xspi_sdma_handle(cdns_xspi);
+				if (cdns_xspi_stig_ready(cdns_xspi, true))
+					return -EIO;
+
+				cdns_xspi->in_buffer += current_cycle_count;
+				cdns_xspi->out_buffer += current_cycle_count;
+			}
+
+			if (rxd) {
+				int j;
+
+				for (j = 0; j < current_cycle_count / 8; j++)
+					cdns_xspi_read_single_qword(cdns_xspi, &rxd);
+				cdns_xspi_finish_read(cdns_xspi, &rxd, current_cycle_count);
+			} else {
+				cdns_xspi->current_xfer_qword += current_cycle_count /
+								 MRVL_XFER_QWORD_BYTECOUNT;
+				if (current_cycle_count % MRVL_XFER_QWORD_BYTECOUNT)
+					cdns_xspi->current_xfer_qword++;
+
+				cdns_xspi->current_xfer_qword %= MRVL_XFER_QWORD_COUNT;
+			}
+			cs_change = t->cs_change;
+			t->len -= current_cycle_count;
+		}
+	}
+
+	if (!cs_change) {
+		u32 xfer_control = readl(cdns_xspi->xferbase + MRVL_XFER_FUNC_CTRL);
+
+		xfer_control &= ~(MRVL_XFER_RECEIVE_ENABLE |
+				  MRVL_XFER_SOFT_RESET);
+		writel(xfer_control, cdns_xspi->xferbase + MRVL_XFER_FUNC_CTRL);
+		cdns_xspi->xfer_in_progress = false;
+	}
+
+	m->status = 0;
+	spi_finalize_current_message(controller);
+
+	return 0;
+}
+
 static int cdns_xspi_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -903,6 +1138,15 @@ static int cdns_xspi_probe(struct platform_device *pdev)
 		return PTR_ERR(cdns_xspi->auxbase);
 	}
 
+	if (cdns_xspi->mrvl_hw_overlay) {
+		cdns_xspi->xferbase = devm_platform_ioremap_resource(pdev, 3);
+		if (IS_ERR(cdns_xspi->xferbase)) {
+			dev_info(dev, "XFER register base not found, set it\n");
+			// For compatibility with older firmware
+			cdns_xspi->xferbase = cdns_xspi->iobase + 0x8000;
+		}
+	}
+
 	cdns_xspi->irq = platform_get_irq(pdev, 0);
 	if (cdns_xspi->irq < 0)
 		return -ENXIO;
@@ -917,6 +1161,7 @@ static int cdns_xspi_probe(struct platform_device *pdev)
 	if (drv_data->mrvl_hw_overlay) {
 		cdns_mrvl_xspi_setup_clock(cdns_xspi, MRVL_DEFAULT_CLK);
 		cdns_xspi_configure_phy(cdns_xspi);
+		host->transfer_one_message = cdns_xspi_transfer_one_message_b0;
 	}
 
 	cdns_xspi_print_phy_config(cdns_xspi);
-- 
2.43.0

Re: (subset) [PATCH v6 0/5] Marvell HW overlay support for Cadence xSPI

[Mark Brown]

On Wed, 29 May 2024 00:40:31 -0700, Witold Sadowski wrote:
> This patch series adds support for the second version of the Marvell
> hardware overlay for the Cadence xSPI IP block. The overlay is a hardware
> change made around the original xSPI block. It extends xSPI features with
> clock configuration, interrupt masking, and full-duplex, variable-length SPI
> operations.
> 
> These functionalities allow the xSPI block to operate not only with memory
> devices but also with simple SPI devices and TPM devices.
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/5] spi: cadence: Ensure data lines set to low during dummy-cycle period
      commit: 4a69c1264ff41bc5bf7c03101ada0454fbf08868

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark