Re: [PATCH] config: imx: Add PHYTEC's phycore-imx8mm-fspi_defconfig

[Lukasz Majewski <lukma@denx.de>]

[-- Attachment #1: Type: text/plain, Size: 7681 bytes --]

Hi Teresa,

> Hello Lukasz,
> 
> Am Donnerstag, dem 15.08.2024 um 10:40 +0200 schrieb Lukasz Majewski:
> > This configuration file provides support for booting phycore module
> > (on e.g. polis-rdk base development board) from QSPI memory.
> > 
> > Moreover, the SDP SPL gadget is supported, so single flash.bin
> > binary can be used with uuu (with uuu -v -b qspi ~/u-boot/flash.bin)
> > to flash QSPI in the factory or during debricking.
> > 
> > Signed-off-by: Lukasz Majewski <lukma@denx.de>
> > ---
> >  configs/phycore-imx8mm-fspi_defconfig | 158
> > ++++++++++++++++++++++++++
> >  1 file changed, 158 insertions(+)
> >  create mode 100644 configs/phycore-imx8mm-fspi_defconfig
> > 
> > diff --git a/configs/phycore-imx8mm-fspi_defconfig
> > b/configs/phycore- imx8mm-fspi_defconfig
> > new file mode 100644
> > index 0000000000..79a2668254
> > --- /dev/null
> > +++ b/configs/phycore-imx8mm-fspi_defconfig
> > @@ -0,0 +1,158 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_IMX8M=y
> > +CONFIG_TEXT_BASE=0x40200000
> > +CONFIG_SYS_MALLOC_LEN=0x2000000
> > +CONFIG_SPL_GPIO=y
> > +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> > +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> > +CONFIG_SF_DEFAULT_SPEED=80000000
> > +CONFIG_ENV_SIZE=0x10000
> > +CONFIG_ENV_OFFSET=0x3C0000
> > +CONFIG_IMX_CONFIG="board/freescale/imx8mm_evk/imximage-8mm-lpddr4-
> > fspi.cfg"  
> 
> can you create a cfg in the board folder and not use the one from the
> evk?

I wanted to avoid code duplication - as the same file (from EVK) is
used by other boards already...

> 
> > +CONFIG_DM_GPIO=y
> > +CONFIG_DEFAULT_DEVICE_TREE="freescale/imx8mm-phyboard-polis-rdk"
> > +CONFIG_SPL_TEXT_BASE=0x7E2000
> > +CONFIG_TARGET_PHYCORE_IMX8MM=y
> > +CONFIG_DM_RESET=y
> > +CONFIG_SYS_MONITOR_LEN=524288
> > +CONFIG_SPL_MMC=y
> > +CONFIG_SPL_SERIAL=y
> > +CONFIG_SPL_DRIVERS_MISC=y
> > +CONFIG_SPL_STACK=0x920000
> > +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
> > +CONFIG_SPL_BSS_START_ADDR=0x910000
> > +CONFIG_SPL_BSS_MAX_SIZE=0x2000
> > +CONFIG_SPL=y
> > +CONFIG_ENV_OFFSET_REDUND=0x3E0000
> > +CONFIG_SYS_LOAD_ADDR=0x40480000
> > +CONFIG_PCI=y
> > +# CONFIG_ANDROID_BOOT_IMAGE is not set
> > +CONFIG_FIT=y
> > +CONFIG_FIT_EXTERNAL_OFFSET=0x3000
> > +CONFIG_SPL_LOAD_FIT=y
> > +CONFIG_OF_SYSTEM_SETUP=y
> > +CONFIG_USE_BOOTCOMMAND=y
> > +CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run
> > loadimage; then run mmcboot; else run netboot; fi; fi;"
> > +CONFIG_DEFAULT_FDT_FILE="oftree"
> > +CONFIG_SYS_CBSIZE=2048
> > +CONFIG_SYS_PBSIZE=2074
> > +CONFIG_BOARD_LATE_INIT=y
> > +CONFIG_SPL_MAX_SIZE=0x25000  
> 
> This line
> 
> > +CONFIG_SPL_PAD_TO=0x0  
> 
> and this one is not available in phycore-imx8mm_defconfig.
> Why have you added them here?

I think that I've followed ./configs/imx8mm_beacon_fspi_defconfig as a
starting point.

I would need to check if removing them would make any harm.

> 
> > +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
> > +CONFIG_SPL_SYS_MALLOC=y
> > +CONFIG_SPL_HAS_CUSTOM_MALLOC_START=y
> > +CONFIG_SPL_CUSTOM_SYS_MALLOC_ADDR=0x42200000
> > +CONFIG_SPL_SYS_MALLOC_SIZE=0x80000
> > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
> > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
> > +CONFIG_SPL_I2C=y
> > +CONFIG_SPL_NOR_SUPPORT=y
> > +CONFIG_SPL_POWER=y
> > +CONFIG_SPL_SPI_FLASH_MTD=y
> > +CONFIG_SPL_WATCHDOG=y
> > +CONFIG_HUSH_PARSER=y
> > +CONFIG_SYS_PROMPT="u-boot=> "
> > +# CONFIG_CMD_EXPORTENV is not set
> > +# CONFIG_CMD_IMPORTENV is not set  
> 
> Here is
> 
> CONFIG_CMD_ERASEENV=y
> 
> missing. Which was added with 60e01c6d9f892bfa088a0453cd19d6a418b00add
> for phycore-imx8mm_defconfig. Why did you not add it?
> 

I might used either the older ./configs/phycore-imx8mm_defconfig or the
above mentioned "beacon".

> 
> > +# CONFIG_CMD_CRC32 is not set
> > +CONFIG_CMD_EEPROM=y
> > +CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2
> > +CONFIG_SYS_EEPROM_SIZE=4096
> > +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=5
> > +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5  
> 
> And I also miss
> 
> # CONFIG_CMD_BIND is not set
> CONFIG_FASTBOOT_BUF_SIZE=0x20000000
> 
> which you did set in your 
> 
> "config: imx: Add support for Phytec's phycore imx8mm running SDP
> gadget"
> 
> patch for phycore-imx8mm_defconfig. Are they not required for fspi
> image?

IIRC this value has default value set in drivers/fastboot/Kconfig

With QSPI setup I did not needed it so big, as the flash.bin was small
enough.

With phycore-imx8mm_defconfig I've set it to larger value - as one my
update with it SD/eMMC memory with fastboot gadget.

> 
> Teresa
> 
> > +CONFIG_CMD_CLK=y
> > +CONFIG_CMD_FUSE=y
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_PCI=y
> > +CONFIG_CMD_SF_TEST=y
> > +CONFIG_CMD_DHCP=y
> > +CONFIG_CMD_MII=y
> > +CONFIG_CMD_PING=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_REGULATOR=y
> > +CONFIG_CMD_EXT2=y
> > +CONFIG_CMD_EXT4=y
> > +CONFIG_CMD_EXT4_WRITE=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_OF_CONTROL=y
> > +CONFIG_SPL_OF_CONTROL=y
> > +CONFIG_ENV_OVERWRITE=y
> > +CONFIG_ENV_IS_IN_MMC=y
> > +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> > +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> > +CONFIG_SYS_MMC_ENV_DEV=2
> > +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
> > +CONFIG_SPL_DM=y
> > +CONFIG_SPL_CLK_COMPOSITE_CCF=y
> > +CONFIG_CLK_COMPOSITE_CCF=y
> > +CONFIG_SPL_CLK_IMX8MM=y
> > +CONFIG_CLK_IMX8MM=y
> > +CONFIG_USB_FUNCTION_FASTBOOT=y
> > +CONFIG_FASTBOOT_BUF_ADDR=0x42800000
> > +CONFIG_FASTBOOT_UUU_SUPPORT=y
> > +CONFIG_MXC_GPIO=y
> > +CONFIG_DM_I2C=y
> > +CONFIG_MISC=y
> > +CONFIG_I2C_EEPROM=y
> > +CONFIG_SYS_I2C_EEPROM_ADDR=0x51
> > +CONFIG_SUPPORT_EMMC_BOOT=y
> > +CONFIG_MMC_IO_VOLTAGE=y
> > +CONFIG_MMC_UHS_SUPPORT=y
> > +CONFIG_MMC_HS400_ES_SUPPORT=y
> > +CONFIG_MMC_HS400_SUPPORT=y
> > +CONFIG_FSL_USDHC=y
> > +CONFIG_MTD=y
> > +CONFIG_DM_MTD=y
> > +CONFIG_DM_SPI_FLASH=y
> > +CONFIG_SF_DEFAULT_BUS=3
> > +CONFIG_SPI_FLASH_BAR=y
> > +CONFIG_SPI_FLASH_MACRONIX=y
> > +CONFIG_SPI_FLASH_SPANSION=y
> > +CONFIG_SPI_FLASH_STMICRO=y
> > +CONFIG_SPI_FLASH_SST=y
> > +CONFIG_SPI_FLASH_WINBOND=y
> > +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> > +CONFIG_SPI_FLASH_MTD=y
> > +CONFIG_PHYLIB=y
> > +CONFIG_PHY_TI_DP83867=y
> > +CONFIG_PHY_GIGE=y
> > +CONFIG_FEC_MXC=y
> > +CONFIG_MII=y
> > +CONFIG_NVME_PCI=y
> > +CONFIG_PCIE_DW_IMX=y
> > +CONFIG_PHY_IMX8M_PCIE=y
> > +CONFIG_PINCTRL=y
> > +CONFIG_SPL_PINCTRL=y
> > +CONFIG_PINCTRL_IMX8M=y
> > +CONFIG_POWER_DOMAIN=y
> > +CONFIG_IMX8M_POWER_DOMAIN=y
> > +CONFIG_DM_REGULATOR_FIXED=y
> > +CONFIG_DM_REGULATOR_GPIO=y
> > +CONFIG_DM_SERIAL=y
> > +CONFIG_MXC_UART=y
> > +CONFIG_SPI=y
> > +CONFIG_DM_SPI=y
> > +CONFIG_NXP_FSPI=y
> > +CONFIG_SYSRESET=y
> > +CONFIG_SPL_SYSRESET=y
> > +CONFIG_SYSRESET_PSCI=y
> > +CONFIG_SYSRESET_WATCHDOG=y
> > +CONFIG_DM_THERMAL=y
> > +CONFIG_IMX_TMU=y
> > +CONFIG_USB=y
> > +CONFIG_SPL_USB_HOST=y
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_MXC_USB_OTG_HACTIVE=y
> > +CONFIG_USB_GADGET=y
> > +CONFIG_SPL_USB_GADGET=y
> > +CONFIG_USB_GADGET_VENDOR_NUM=0x0525
> > +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
> > +CONFIG_CI_UDC=y
> > +CONFIG_SDP_LOADADDR=0x40400000
> > +CONFIG_SPL_USB_SDP_SUPPORT=y
> > +CONFIG_IMX_WATCHDOG=y
> > +CONFIG_FSPI_CONF_HEADER=y
> > +CONFIG_FSPI_CONF_FILE="fspi_header.bin"  
> 




Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 488 bytes --]