[PATCH v6 2/2] dt-bindings: mtd: davinci: convert to yaml

[Marcus Folkesson <marcus.folkesson@gmail.com>]

Convert the bindings to yaml format.

Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
---
 .../devicetree/bindings/mtd/davinci-nand.txt       |  94 ---------------
 .../devicetree/bindings/mtd/ti,davinci-nand.yaml   | 134 +++++++++++++++++++++
 2 files changed, 134 insertions(+), 94 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
deleted file mode 100644
index eb8e2ff4dbd2901b3c396f2e66c1f590a32dcf67..0000000000000000000000000000000000000000
--- a/Documentation/devicetree/bindings/mtd/davinci-nand.txt
+++ /dev/null
@@ -1,94 +0,0 @@
-Device tree bindings for Texas instruments Davinci/Keystone NAND controller
-
-This file provides information, what the device node for the davinci/keystone
-NAND interface contains.
-
-Documentation:
-Davinci DM646x - https://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
-Kestone - https://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
-
-Required properties:
-
-- compatible:			"ti,davinci-nand"
-				"ti,keystone-nand"
-
-- reg:				Contains 2 offset/length values:
-				- offset and length for the access window.
-				- offset and length for accessing the AEMIF
-				control registers.
-
-- ti,davinci-chipselect:	number of chipselect. Indicates on the
-				davinci_nand driver which chipselect is used
-				for accessing the nand.
-				Can be in the range [0-3].
-
-Recommended properties :
-
-- ti,davinci-mask-ale:		mask for ALE. Needed for executing address
-				phase. These offset will be added to the base
-				address for the chip select space the NAND Flash
-				device is connected to.
-				If not set equal to 0x08.
-
-- ti,davinci-mask-cle:		mask for CLE. Needed for executing command
-				phase. These offset will be added to the base
-				address for the chip select space the NAND Flash
-				device is connected to.
-				If not set equal to 0x10.
-
-- ti,davinci-mask-chipsel:	mask for chipselect address. Needed to mask
-				addresses for given chipselect.
-
-- nand-ecc-mode:		operation mode of the NAND ecc mode. ECC mode
-				valid values for davinci driver:
-				- "none"
-				- "soft"
-				- "hw"
-
-- ti,davinci-ecc-bits:		used ECC bits, currently supported 1 or 4.
-
-- nand-bus-width:		buswidth 8 or 16. If not present 8.
-
-- nand-on-flash-bbt:		use flash based bad block table support. OOB
-				identifier is saved in OOB area. If not present
-				false.
-
-Deprecated properties:
-
-- ti,davinci-ecc-mode:		operation mode of the NAND ecc mode. ECC mode
-				valid values for davinci driver:
-				- "none"
-				- "soft"
-				- "hw"
-
-- ti,davinci-nand-buswidth:	buswidth 8 or 16. If not present 8.
-
-- ti,davinci-nand-use-bbt:	use flash based bad block table support. OOB
-				identifier is saved in OOB area. If not present
-				false.
-
-Nand device bindings may contain additional sub-nodes describing partitions of
-the address space. See mtd.yaml for more detail. The NAND Flash timing
-values must be programmed in the chip select’s node of AEMIF
-memory-controller (see Documentation/devicetree/bindings/memory-controllers/
-davinci-aemif.txt).
-
-Example(da850 EVM ):
-
-nand_cs3@62000000 {
-	compatible = "ti,davinci-nand";
-	reg = <0x62000000 0x807ff
-	       0x68000000 0x8000>;
-	ti,davinci-chipselect = <1>;
-	ti,davinci-mask-ale = <0>;
-	ti,davinci-mask-cle = <0>;
-	ti,davinci-mask-chipsel = <0>;
-	nand-ecc-mode = "hw";
-	ti,davinci-ecc-bits = <4>;
-	nand-on-flash-bbt;
-
-	partition@180000 {
-		label = "ubifs";
-		reg = <0x180000 0x7e80000>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/mtd/ti,davinci-nand.yaml b/Documentation/devicetree/bindings/mtd/ti,davinci-nand.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..fffdaa9bf85ac2ffb1b177bdc693c995d2a8ea20
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/ti,davinci-nand.yaml
@@ -0,0 +1,134 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/ti,davinci-nand.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI DaVinci NAND controller
+
+maintainers:
+  - Marcus Folkesson <marcus.folkesson@gmail.com>
+
+allOf:
+  - $ref: nand-controller.yaml
+
+properties:
+  compatible:
+    enum:
+      - ti,davinci-nand
+      - ti,keystone-nand
+
+  reg:
+    items:
+      - description:
+          Access window.
+      - description:
+          AEMIF control registers
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  partitions:
+    $ref: /schemas/mtd/partitions/partitions.yaml
+
+  ti,davinci-chipselect:
+    description:
+      Number of chipselect. Indicate on the davinci_nand driver which
+      chipselect is used for accessing the nand.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 3]
+
+  ti,davinci-mask-ale:
+    description:
+      Mask for ALE. Needed for executing address phase. These offset will be
+      added to the base address for the chip select space the NAND Flash
+      device is connected to.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0x08
+
+  ti,davinci-mask-cle:
+    description:
+      Mask for CLE. Needed for executing command phase. These offset will be
+      added to the base address for the chip select space the NAND Flash device
+      is connected to.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0x10
+
+  ti,davinci-mask-chipsel:
+    description:
+      Mask for chipselect address. Needed to mask addresses for given
+      chipselect.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
+
+  ti,davinci-ecc-bits:
+    description: Used ECC bits.
+    enum: [1, 4]
+
+  ti,davinci-ecc-mode:
+    description: Operation mode of the NAND ECC mode.
+    $ref: /schemas/types.yaml#/definitions/string
+    enum: [none, soft, hw, on-die]
+    deprecated: true
+
+  ti,davinci-nand-buswidth:
+    description: Bus width to the NAND chip
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [8, 16]
+    default: 8
+    deprecated: true
+
+  ti,davinci-nand-use-bbt:
+    type: boolean
+    description:
+      Use flash based bad block table support. OOB identifier is saved in OOB
+      area.
+    deprecated: true
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+  - ti,davinci-chipselect
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    bus {
+      #address-cells = <2>;
+      #size-cells = <1>;
+
+      nand-controller@2000000,0 {
+        compatible = "ti,davinci-nand";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0 0x02000000 0x02000000
+        1 0x00000000 0x00008000>;
+
+        ti,davinci-chipselect = <1>;
+        ti,davinci-mask-ale = <0>;
+        ti,davinci-mask-cle = <0>;
+        ti,davinci-mask-chipsel = <0>;
+
+        ti,davinci-nand-buswidth = <16>;
+        ti,davinci-ecc-mode = "hw";
+        ti,davinci-ecc-bits = <4>;
+        ti,davinci-nand-use-bbt;
+
+        partitions {
+          compatible = "fixed-partitions";
+          #address-cells = <1>;
+          #size-cells = <1>;
+
+          partition@0 {
+            label = "u-boot env";
+            reg = <0 0x020000>;
+          };
+        };
+      };
+    };

-- 
2.47.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/