Re: PCI: hotplug_event: PCIe PLDA Device BAR Reset

[Bjorn Helgaas <helgaas@kernel.org>]

On Tue, Feb 25, 2025 at 06:46:02PM +0530, Naveen Kumar P wrote:
> On Tue, Feb 25, 2025 at 1:24 AM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > On Tue, Feb 25, 2025 at 12:29:00AM +0530, Naveen Kumar P wrote:
> > > On Mon, Feb 24, 2025 at 11:03 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > > > On Mon, Feb 24, 2025 at 05:45:35PM +0530, Naveen Kumar P wrote:
> > > > > On Wed, Feb 19, 2025 at 10:36 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > > > > > On Wed, Feb 19, 2025 at 05:52:47PM +0530, Naveen Kumar P wrote:
> > > > > > > Hi all,
> > > > > > >
> > > > > > > I am writing to seek assistance with an issue we are experiencing with
> > > > > > > a PCIe device (PLDA Device 5555) connected through PCI Express Root
> > > > > > > Port 1 to the host bridge.
> > > > > > >
> > > > > > > We have observed that after booting the system, the Base Address
> > > > > > > Register (BAR0) memory of this device gets reset to 0x0 after
> > > > > > > approximately one hour or more (the timing is inconsistent). This was
> > > > > > > verified using the lspci output and the setpci -s 01:00.0
> > > > > > > BASE_ADDRESS_0 command.
> >
> > > ...
> > > I booted with the pcie_aspm=off kernel parameter, which means that
> > > PCIe Active State Power Management (ASPM) is disabled. Given this
> > > context, should I consider removing this setting to see if it affects
> > > the occurrence of the Bus Check notifications and the BAR0 reset
> > > issue?
> >
> > Doesn't seem likely to be related.  Once configured, ASPM operates
> > without any software intervention.  But note that "pcie_aspm=off"
> > means the kernel doesn't touch ASPM configuration at all, and any
> > configuration done by firmware remains in effect.
> >
> > You can tell whether ASPM has been enabled by firmware with "sudo
> > lspci -vv" before the problem occurs.
> >
> > > > > During the ACPI_NOTIFY_BUS_CHECK event, the lspci output initially
> > > > > showed all FF's, and then the next run of the same command showed
> > > > > BASE_ADDRESS_0 reset to zero:
> > > > > $ sudo lspci -xxx -s 01:00.0 | grep "10:"
> > > > > 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> > > >
> > > > Looks like the device isn't responding at all here.  Could happen if
> > > > the device is reset or powered down.
> > >
> > > From the kernel driver or user space tools, is it possible to
> > > determine whether the device has been reset or powered down?  Are
> > > there any power management settings or configurations that could be
> > > causing the device to reset or power down unexpectedly?
> >
> > Not really.  By "powered down", I meant D3cold, where the main power
> > is removed.  Config space is readable in all other power states.
> >
> > > > What is this device?  What driver is bound to it?  I don't see
> > > > anything in dmesg that identifies a driver.
> > >
> > > The PCIe device in question is a Xilinx FPGA endpoint, which is
> > > flashed with RTL code to expose several host interfaces to the system
> > > via the PCIe link.
> > >
> > > We have an out-of-tree driver for this device, but to eliminate the
> > > driver's role in this issue, I renamed the driver to prevent it from
> > > loading automatically after rebooting the machine. Despite not using
> > > the driver, the issue still occurred.
> >
> > Oh, right, I forgot that you mentioned this before.
> >
> > > > You're seeing the problem on v5.4 (Nov 2019), which is much newer than
> > > > v4.4 (Jan 2016).  But v5.4 is still really too old to spend a lot of
> > > > time on unless the problem still happens on a current kernel.
> >
> > This part is important.  We don't want to spend a lot of time
> > debugging an issue that may have already been fixed upstream.
>
> Sure, I started building the 6.13 kernel and will post more
> information if I notice the issue on the 6.13 kernel.
> 
> Regarding the CommClk- (Common Clock Configuration) bit, it indicates
> whether the common clock configuration is enabled or disabled. When it
> is set to CommClk-, it means that the common clock configuration is
> disabled.
> 
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
>         ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> 
> For my device, I noticed that the common clock configuration is
> disabled. Could this be causing the BAR reset issue?

Not to my knowledge.

> How is the CommClk bit determined(to set or clear)? and is it okay to
> enable this bit after booting the kernel?

It is somewhere in drivers/pci/pcie/aspm.c, i.e.,
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/pci/pcie/aspm.c?id=v6.13#n383

_______________________________________________
Kernelnewbies mailing list
Kernelnewbies@kernelnewbies.org
https://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies