[PATCH 0/1] xhci fix for usb-linus

[PATCH 0/1] xhci fix for usb-linus

[Mathias Nyman]

Hi Greg

Michal found and fixed a regression introduced in 6.13
If possible it would be nice to get this into 6.14 still

Thanks
Mathias

Michal Pecio (1):
  usb: xhci: Fix host controllers "dying" after suspend and resume

 drivers/usb/host/xhci.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

-- 
2.43.0

[PATCH 1/1] usb: xhci: Fix host controllers "dying" after suspend and resume

[Mathias Nyman]

From: Michal Pecio <michal.pecio@gmail.com>

A recent cleanup went a bit too far and dropped clearing the cycle bit
of link TRBs, so it stays different from the rest of the ring half of
the time. Then a race occurs: if the xHC reaches such link TRB before
more commands are queued, the link's cycle bit unintentionally matches
the xHC's cycle so it follows the link and waits for further commands.
If more commands are queued before the xHC gets there, inc_enq() flips
the bit so the xHC later sees a mismatch and stops executing commands.

This function is called before suspend and 50% of times after resuming
the xHC is doomed to get stuck sooner or later. Then some Stop Endpoint
command fails to complete in 5 seconds and this shows up

xhci_hcd 0000:00:10.0: xHCI host not responding to stop endpoint command
xhci_hcd 0000:00:10.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:10.0: HC died; cleaning up

followed by loss of all USB decives on the affected bus. That's if you
are lucky, because if Set Deq gets stuck instead, the failure is silent.

Likely responsible for kernel bug 219824. I found this while searching
for possible causes of that regression and reproduced it locally before
hearing back from the reporter. To repro, simply wait for link cycle to
become set (debugfs), then suspend, resume and wait. To accelerate the
failure I used a script which repeatedly starts and stops a UVC camera.

Some HCs get fully reinitialized on resume and they are not affected.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=219824
Fixes: 36b972d4b7ce ("usb: xhci: improve xhci_clear_command_ring()")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
---
 drivers/usb/host/xhci.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 45653114ccd7..1a90ebc8a30e 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -780,8 +780,12 @@ static void xhci_clear_command_ring(struct xhci_hcd *xhci)
 	struct xhci_segment *seg;
 
 	ring = xhci->cmd_ring;
-	xhci_for_each_ring_seg(ring->first_seg, seg)
+	xhci_for_each_ring_seg(ring->first_seg, seg) {
+		/* erase all TRBs before the link */
 		memset(seg->trbs, 0, sizeof(union xhci_trb) * (TRBS_PER_SEGMENT - 1));
+		/* clear link cycle bit */
+		seg->trbs[TRBS_PER_SEGMENT - 1].link.control &= cpu_to_le32(~TRB_CYCLE);
+	}
 
 	xhci_initialize_ring_info(ring);
 	/*
-- 
2.43.0