[net-next v12 3/7] ARM: dts: nxp: mxs: Adjust XEA board's DTS to support L2 switch

[Lukasz Majewski <lukma@denx.de>]

The description is similar to the one used with the new CPSW driver.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>

---
Changes for v2:
- Remove properties which are common for the imx28(7) SoC
- Use mdio properties to perform L2 switch reset (avoid using
  deprecated properties)

Changes for v3:
- Replace IRQ_TYPE_EDGE_FALLING with IRQ_TYPE_LEVEL_LOW
- Update comment regarding PHY interrupts s/AND/OR/g

Changes for v4:
- Use GPIO_ACTIVE_LOW instead of 0 in 'reset-gpios'
- Replace port@[12] with ethernet-port@[12]

Changes for v5:
- Add proper multiline comment for IRQs description

Changes for v6:
- None

Changes for v7:
- None

Changes for v8:
- None

Changes for v9:
- None

Changes for v10:
- None

Changes for v11:
- None

Changes for v12:
- None
---
 arch/arm/boot/dts/nxp/mxs/imx28-xea.dts | 56 +++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts b/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
index 6c5e6856648a..69032b29d767 100644
--- a/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
@@ -5,6 +5,7 @@
  */
 
 /dts-v1/;
+#include<dt-bindings/interrupt-controller/irq.h>
 #include "imx28-lwe.dtsi"
 
 / {
@@ -90,6 +91,61 @@ &reg_usb_5v {
 	gpio = <&gpio0 2 0>;
 };
 
+&eth_switch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>, <&mac1_pins_a>;
+	phy-supply = <&reg_fec_3v3>;
+	status = "okay";
+
+	ethernet-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mtip_port1: ethernet-port@1 {
+			reg = <1>;
+			label = "lan0";
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-mode = "rmii";
+			phy-handle = <&ethphy0>;
+		};
+
+		mtip_port2: ethernet-port@2 {
+			reg = <2>;
+			label = "lan1";
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-mode = "rmii";
+			phy-handle = <&ethphy1>;
+		};
+	};
+
+	mdio_sw: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio3 21 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <25000>;
+		reset-post-delay-us = <10000>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+			smsc,disable-energy-detect;
+			/*
+			 * Both PHYs (i.e. 0,1) have the same, single GPIO,
+			 * line to handle both, their interrupts (OR'ed)
+			 */
+			interrupt-parent = <&gpio4>;
+			interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+		};
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+			smsc,disable-energy-detect;
+			interrupt-parent = <&gpio4>;
+			interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
 &spi2_pins_a {
 	fsl,pinmux-ids = <
 		MX28_PAD_SSP2_SCK__SSP2_SCK
-- 
2.39.5