[PATCH v4 3/4] arm64: dts: rockchip: describe I2c Bus 1 and IMX258 world camera on PinePhone Pro

[Olivier Benjamin <olivier.benjamin@bootlin.com>]

Add the description of the rear/world camera (IMX258) on the PinePhone Pro
to the device dts file.
It receives commands on the I2C Bus 1 at address 0x1a and transmits data
over CSI-MIPI.

The I2C address for IMX258 can be found in the IMX258-0AQH5 Software
Reference Manual, page 24, section 2.3.1: 0b0011010 = 0x1a.
Section 3 indicates the module has 4 pairs of data lines. While 4-lane
mode is nominal, 2-lane mode should also be supported.

The pin muxing info was extracted from the PinePhone Pro schematic v1.0
as well as the RK3399 datasheet revision 1.8.

Table 2-3 in section 2.8 of the RK3399 datasheet contains the mapping
of IO functions for the SoC pins. Page 52 shows GPIO1_A0, page 54 shows
GPIO2_D4.

For I2C power, the PinePhone Pro schematic page 11 quadrants A4 and A5:
RK3399_J.AA8 and RK3399_J.Y8 get power from vcaa1v8_codec, so turn it on

The IMX258 also uses the following regulators, expected by its driver:
 - vana (2.8V analog), called AVDD2V8_DVP on P.18 q.C1 and derived from
   VCC1V8_S3 on P.13 q.B2
 - vdig (1.2V digital core), called DVDD_DVP on P.18 q.C1 and shown on
   P.18 q.D3 to be equivalent to VCC1V2_DVP derived from VCC3V3_SYS on
   P.13 q.B3. Note that this regulator's voltage is inconsistently
   labeled either 1.2V or 1.5V

RK3399_J.AG1 is GPIO4_A1/I2C1_SDA, RK3399_J.Y6 is GPIO4_A2/I2C1_SCL
This is the default pinctrl "i2c1_xfer" for i2c1 from rk3399-base.

For the reset (RESET) signal:
page 11 quadrant D2             | p.18 q.C3-4 | p.18 q.C2
RK3399_E.R25 -> GPIO1_A0 -> Camera_RST -> MIPI_RST0 -> IMX258.12

For the powerdown (PWDN) signal:
page 11 quadrants B4-5          | p.18 q.C2
RK3399_G.AF8 -> GPIO2_D4 -> DVP_PDN1_H -> IMX258.14

Helped-by: Dragan Simic <dsimic@manjaro.org>
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Olivier Benjamin <olivier.benjamin@bootlin.com>
---
 .../boot/dts/rockchip/rk3399-pinephone-pro.dts     | 93 ++++++++++++++++++++++
 1 file changed, 93 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
index 04ba4c4565d0a205e2e46d7535c6a3190993621d..b335d044138b413359ba54269ab646142254a55f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
@@ -114,6 +114,16 @@ vcc3v3_sys: regulator-vcc3v3-sys {
 		vin-supply = <&vcc_sys>;
 	};
 
+	avdd2v8_dvp: regulator-avdd2v8-dvp {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8_dvp";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
 	vcca1v8_s3: regulator-vcc1v8-s3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcca1v8_s3";
@@ -136,6 +146,16 @@ vcc1v8_codec: regulator-vcc1v8-codec {
 		vin-supply = <&vcc3v3_sys>;
 	};
 
+	vcc1v2_dvp: regulator-vcc1v2-dvp {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v2_dvp";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&vcca1v8_s3>;
+	};
+
 	wifi_pwrseq: sdio-wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		clocks = <&rk818 1>;
@@ -312,6 +332,8 @@ vcc3v0_touch: LDO_REG2 {
 
 			vcca1v8_codec: LDO_REG3 {
 				regulator-name = "vcca1v8_codec";
+				regulator-always-on;
+				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 			};
@@ -420,6 +442,45 @@ regulator-state-mem {
 	};
 };
 
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c1_xfer &cif_clkouta>;
+	assigned-clocks = <&cru SCLK_CIF_OUT>;
+	assigned-clock-rates = <24000000>;
+	status = "okay";
+
+	wcam: camera@1a {
+		compatible = "sony,imx258";
+		reg = <0x1a>;
+		clocks = <&cru SCLK_CIF_OUT>; /* MIPI_MCLK0, derived from CIF_CLKO */
+		pinctrl-names = "default";
+		pinctrl-0 = <&camera_rst>;
+		/* Note: both cameras also depend on vcca1v8_codec to power the I2C bus. */
+		vif-supply = <&vcc1v8_dvp>;
+		vana-supply = <&avdd2v8_dvp>;
+		vdig-supply = <&vcc1v2_dvp>; /* DVDD_DVP is the same as VCC1V2_DVP */
+		reset-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_LOW>;
+		orientation = <1>; /* V4L2_CAMERA_ORIENTATION_BACK */
+		rotation = <270>;
+		lens-focus = <&wcam_lens>;
+
+		port {
+			wcam_out: endpoint {
+				remote-endpoint = <&mipi_in_wcam>;
+				data-lanes = <1 2 3 4>;
+				link-frequencies = /bits/ 64 <636000000>;
+			};
+		};
+	};
+
+	wcam_lens: camera-lens@c {
+		compatible = "dongwoon,dw9714";
+		reg = <0x0c>;
+		/* Same I2c bus as both cameras, depends on vcca1v8_codec for power. */
+		vcc-supply = <&vcc1v8_dvp>;
+	};
+};
+
 &i2c3 {
 	i2c-scl-rising-time-ns = <450>;
 	i2c-scl-falling-time-ns = <15>;
@@ -462,6 +523,28 @@ &io_domains {
 	status = "okay";
 };
 
+&isp1 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			mipi_in_wcam: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&wcam_out>;
+				data-lanes = <1 2 3 4>;
+			};
+		};
+	};
+};
+
+&mipi_dphy_rx0 {
+	status = "okay";
+};
+
+&isp1_mmu {
+	status = "okay";
+};
+
 &mipi_dsi {
 	status = "okay";
 	clock-master;
@@ -495,6 +578,10 @@ mipi_in_panel: endpoint {
 	};
 };
 
+&mipi_dsi1 {
+	status = "okay";
+};
+
 &pmu_io_domains {
 	pmu1830-supply = <&vcc_1v8>;
 	status = "okay";
@@ -507,6 +594,12 @@ pwrbtn_pin: pwrbtn-pin {
 		};
 	};
 
+	camera {
+		camera_rst_l: camera-rst-l {
+			rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	leds {
 		red_led_pin: red-led-pin {
 			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;

-- 
2.49.0