From: Hal Feng <hal.feng@starfivetech.com>
To: Conor Dooley <conor+dt@kernel.org>,
Emil Renner Berthing <emil.renner.berthing@canonical.com>,
Heinrich Schuchardt <heinrich.schuchardt@canonical.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Palmer Dabbelt <palmer@dabbelt.com>,
Paul Walmsley <paul.walmsley@sifive.com>,
Albert Ou <aou@eecs.berkeley.edu>
Cc: Hal Feng <hal.feng@starfivetech.com>,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [RFC 2/3] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts
Date: Thu, 21 Aug 2025 18:09:29 +0800 [thread overview]
Message-ID: <20250821100930.71404-3-hal.feng@starfivetech.com> (raw)
In-Reply-To: <20250821100930.71404-1-hal.feng@starfivetech.com>
Some node in this file are not used by the upcoming VisionFive 2 Lite
board. Move them to the board dts to prepare for adding the new
VisionFive 2 Lite device tree.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
---
.../boot/dts/starfive/jh7110-common.dtsi | 22 ---------
.../jh7110-deepcomputing-fml13v01.dts | 49 +++++++++++++++++++
.../boot/dts/starfive/jh7110-milkv-mars.dts | 49 +++++++++++++++++++
.../dts/starfive/jh7110-pine64-star64.dts | 49 +++++++++++++++++++
.../jh7110-starfive-visionfive-2.dtsi | 46 +++++++++++++++++
arch/riscv/boot/dts/starfive/jh7110.dtsi | 16 ------
6 files changed, 193 insertions(+), 38 deletions(-)
diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index 2eaf01775ef5..8332622420ca 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -281,15 +281,9 @@ &mmc0 {
assigned-clock-rates = <50000000>;
bus-width = <8>;
bootph-pre-ram;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- cap-mmc-hw-reset;
post-power-on-delay-ms = <200>;
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&emmc_vdd>;
status = "okay";
};
@@ -299,12 +293,7 @@ &mmc1 {
assigned-clock-rates = <50000000>;
bus-width = <4>;
bootph-pre-ram;
- no-sdio;
- no-mmc;
- cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
- disable-wp;
cap-sd-highspeed;
- post-power-on-delay-ms = <200>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
status = "okay";
@@ -448,17 +437,6 @@ GPOEN_SYS_I2C6_DATA,
};
mmc0_pins: mmc0-0 {
- rst-pins {
- pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
- GPOEN_ENABLE,
- GPI_NONE)>;
- bias-pull-up;
- drive-strength = <12>;
- input-disable;
- input-schmitt-disable;
- slew-rate = <0>;
- };
-
mmc-pins {
pinmux = <PINMUX(PAD_SD0_CLK, 0)>,
<PINMUX(PAD_SD0_CMD, 0)>,
diff --git a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
index f2857d021d68..5a2a41a7e8c3 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
@@ -11,6 +11,55 @@ / {
compatible = "deepcomputing,fml13v01", "starfive,jh7110";
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ no-sdio;
+ no-mmc;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ post-power-on-delay-ms = <200>;
+};
+
&pcie1 {
perst-gpios = <&sysgpio 21 GPIO_ACTIVE_LOW>;
phys = <&pciephy1>;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
index fdaf6b4557da..96f6b2f072d4 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
@@ -11,6 +11,25 @@ / {
compatible = "milkv,mars", "starfive,jh7110";
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
@@ -22,6 +41,36 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ no-sdio;
+ no-mmc;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ post-power-on-delay-ms = <200>;
+};
+
&pcie0 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
index 31e825be2065..c9677aef9ff0 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
@@ -14,6 +14,25 @@ aliases {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
starfive,tx-use-rgmii-clk;
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
@@ -44,6 +63,36 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ no-sdio;
+ no-mmc;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ post-power-on-delay-ms = <200>;
+};
+
&pcie1 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 5f14afb2c24d..d1e4206f1251 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -13,6 +13,25 @@ aliases {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
status = "okay";
};
@@ -38,9 +57,36 @@ &i2c0 {
};
&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
non-removable;
};
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ no-sdio;
+ no-mmc;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ post-power-on-delay-ms = <200>;
+};
+
&pcie0 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 0ba74ef04679..d2463399b959 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -200,22 +200,6 @@ core4 {
cpu_opp: opp-table-0 {
compatible = "operating-points-v2";
opp-shared;
- opp-375000000 {
- opp-hz = /bits/ 64 <375000000>;
- opp-microvolt = <800000>;
- };
- opp-500000000 {
- opp-hz = /bits/ 64 <500000000>;
- opp-microvolt = <800000>;
- };
- opp-750000000 {
- opp-hz = /bits/ 64 <750000000>;
- opp-microvolt = <800000>;
- };
- opp-1500000000 {
- opp-hz = /bits/ 64 <1500000000>;
- opp-microvolt = <1040000>;
- };
};
thermal-zones {
--
2.43.2
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
WARNING: multiple messages have this Message-ID (diff)
From: Hal Feng <hal.feng@starfivetech.com>
To: Conor Dooley <conor+dt@kernel.org>,
Emil Renner Berthing <emil.renner.berthing@canonical.com>,
Heinrich Schuchardt <heinrich.schuchardt@canonical.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Palmer Dabbelt <palmer@dabbelt.com>,
Paul Walmsley <paul.walmsley@sifive.com>,
Albert Ou <aou@eecs.berkeley.edu>
Cc: Hal Feng <hal.feng@starfivetech.com>,
devicetree@vger.kernel.org, linux-riscv@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [RFC 2/3] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts
Date: Thu, 21 Aug 2025 18:09:29 +0800 [thread overview]
Message-ID: <20250821100930.71404-3-hal.feng@starfivetech.com> (raw)
In-Reply-To: <20250821100930.71404-1-hal.feng@starfivetech.com>
Some node in this file are not used by the upcoming VisionFive 2 Lite
board. Move them to the board dts to prepare for adding the new
VisionFive 2 Lite device tree.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
---
.../boot/dts/starfive/jh7110-common.dtsi | 22 ---------
.../jh7110-deepcomputing-fml13v01.dts | 49 +++++++++++++++++++
.../boot/dts/starfive/jh7110-milkv-mars.dts | 49 +++++++++++++++++++
.../dts/starfive/jh7110-pine64-star64.dts | 49 +++++++++++++++++++
.../jh7110-starfive-visionfive-2.dtsi | 46 +++++++++++++++++
arch/riscv/boot/dts/starfive/jh7110.dtsi | 16 ------
6 files changed, 193 insertions(+), 38 deletions(-)
diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index 2eaf01775ef5..8332622420ca 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -281,15 +281,9 @@ &mmc0 {
assigned-clock-rates = <50000000>;
bus-width = <8>;
bootph-pre-ram;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- cap-mmc-hw-reset;
post-power-on-delay-ms = <200>;
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&emmc_vdd>;
status = "okay";
};
@@ -299,12 +293,7 @@ &mmc1 {
assigned-clock-rates = <50000000>;
bus-width = <4>;
bootph-pre-ram;
- no-sdio;
- no-mmc;
- cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
- disable-wp;
cap-sd-highspeed;
- post-power-on-delay-ms = <200>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
status = "okay";
@@ -448,17 +437,6 @@ GPOEN_SYS_I2C6_DATA,
};
mmc0_pins: mmc0-0 {
- rst-pins {
- pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
- GPOEN_ENABLE,
- GPI_NONE)>;
- bias-pull-up;
- drive-strength = <12>;
- input-disable;
- input-schmitt-disable;
- slew-rate = <0>;
- };
-
mmc-pins {
pinmux = <PINMUX(PAD_SD0_CLK, 0)>,
<PINMUX(PAD_SD0_CMD, 0)>,
diff --git a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
index f2857d021d68..5a2a41a7e8c3 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
@@ -11,6 +11,55 @@ / {
compatible = "deepcomputing,fml13v01", "starfive,jh7110";
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ no-sdio;
+ no-mmc;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ post-power-on-delay-ms = <200>;
+};
+
&pcie1 {
perst-gpios = <&sysgpio 21 GPIO_ACTIVE_LOW>;
phys = <&pciephy1>;
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
index fdaf6b4557da..96f6b2f072d4 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
@@ -11,6 +11,25 @@ / {
compatible = "milkv,mars", "starfive,jh7110";
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
@@ -22,6 +41,36 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ no-sdio;
+ no-mmc;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ post-power-on-delay-ms = <200>;
+};
+
&pcie0 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
index 31e825be2065..c9677aef9ff0 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
@@ -14,6 +14,25 @@ aliases {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
starfive,tx-use-rgmii-clk;
assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
@@ -44,6 +63,36 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ no-sdio;
+ no-mmc;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ post-power-on-delay-ms = <200>;
+};
+
&pcie1 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
index 5f14afb2c24d..d1e4206f1251 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -13,6 +13,25 @@ aliases {
};
};
+&cpu_opp {
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-750000000 {
+ opp-hz = /bits/ 64 <750000000>;
+ opp-microvolt = <800000>;
+ };
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1040000>;
+ };
+};
+
&gmac0 {
status = "okay";
};
@@ -38,9 +57,36 @@ &i2c0 {
};
&mmc0 {
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&emmc_vdd>;
non-removable;
};
+&mmc0_pins {
+ rst-pins {
+ pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-pull-up;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+};
+
+&mmc1 {
+ no-sdio;
+ no-mmc;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ post-power-on-delay-ms = <200>;
+};
+
&pcie0 {
status = "okay";
};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 0ba74ef04679..d2463399b959 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -200,22 +200,6 @@ core4 {
cpu_opp: opp-table-0 {
compatible = "operating-points-v2";
opp-shared;
- opp-375000000 {
- opp-hz = /bits/ 64 <375000000>;
- opp-microvolt = <800000>;
- };
- opp-500000000 {
- opp-hz = /bits/ 64 <500000000>;
- opp-microvolt = <800000>;
- };
- opp-750000000 {
- opp-hz = /bits/ 64 <750000000>;
- opp-microvolt = <800000>;
- };
- opp-1500000000 {
- opp-hz = /bits/ 64 <1500000000>;
- opp-microvolt = <1040000>;
- };
};
thermal-zones {
--
2.43.2
next prev parent reply other threads:[~2025-08-21 13:34 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-08-21 10:09 [RFC 0/3] Add support for StarFive VisionFive 2 Lite board Hal Feng
2025-08-21 10:09 ` Hal Feng
2025-08-21 10:09 ` [RFC 1/3] dt-bindings: riscv: Add StarFive JH7110S SoC and " Hal Feng
2025-08-21 10:09 ` Hal Feng
2025-08-21 18:17 ` Conor Dooley
2025-08-21 18:17 ` Conor Dooley
2025-08-22 7:37 ` Hal Feng
2025-08-22 7:37 ` Hal Feng
2025-08-22 16:37 ` Conor Dooley
2025-08-22 16:37 ` Conor Dooley
2025-08-24 17:14 ` Icenowy Zheng
2025-08-24 17:14 ` Icenowy Zheng
2025-08-24 19:48 ` E Shattow
2025-08-24 19:48 ` E Shattow
2025-08-21 10:09 ` Hal Feng [this message]
2025-08-21 10:09 ` [RFC 2/3] riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts Hal Feng
2025-08-21 15:07 ` E Shattow
2025-08-21 15:07 ` E Shattow
2025-08-22 6:11 ` Hal Feng
2025-08-22 6:11 ` Hal Feng
2025-08-21 10:09 ` [RFC 3/3] riscv: dts: starfive: Add VisionFive 2 Lite board device tree Hal Feng
2025-08-21 10:09 ` Hal Feng
2025-08-21 14:08 ` Vivian Wang
2025-08-21 14:08 ` Vivian Wang
2025-08-22 2:13 ` Hal Feng
2025-08-22 2:13 ` Hal Feng
2025-08-23 19:32 ` E Shattow
2025-08-23 19:32 ` E Shattow
2025-08-25 3:20 ` Hal Feng
2025-08-25 3:20 ` Hal Feng
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250821100930.71404-3-hal.feng@starfivetech.com \
--to=hal.feng@starfivetech.com \
--cc=aou@eecs.berkeley.edu \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=emil.renner.berthing@canonical.com \
--cc=heinrich.schuchardt@canonical.com \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.