[PATCH v4 3/3] phy: eswin: Create eswin directory and add EIC7700 SATA PHY driver

[Yulin Lu <luyulin@eswincomputing.com>]

Created the eswin phy driver directory and added support for
the SATA phy driver on the EIC7700 SoC platform.

Signed-off-by: Yulin Lu <luyulin@eswincomputing.com>
---
 drivers/phy/Kconfig                  |   1 +
 drivers/phy/Makefile                 |   1 +
 drivers/phy/eswin/Kconfig            |  14 ++
 drivers/phy/eswin/Makefile           |   2 +
 drivers/phy/eswin/phy-eic7700-sata.c | 192 +++++++++++++++++++++++++++
 5 files changed, 210 insertions(+)
 create mode 100644 drivers/phy/eswin/Kconfig
 create mode 100644 drivers/phy/eswin/Makefile
 create mode 100644 drivers/phy/eswin/phy-eic7700-sata.c

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 58c911e1b2d2..e82ebcfe534a 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -105,6 +105,7 @@ source "drivers/phy/allwinner/Kconfig"
 source "drivers/phy/amlogic/Kconfig"
 source "drivers/phy/broadcom/Kconfig"
 source "drivers/phy/cadence/Kconfig"
+source "drivers/phy/eswin/Kconfig"
 source "drivers/phy/freescale/Kconfig"
 source "drivers/phy/hisilicon/Kconfig"
 source "drivers/phy/ingenic/Kconfig"
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index c670a8dac468..ed7444949259 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -17,6 +17,7 @@ obj-y					+= allwinner/	\
 					   amlogic/	\
 					   broadcom/	\
 					   cadence/	\
+					   eswin/	\
 					   freescale/	\
 					   hisilicon/	\
 					   ingenic/	\
diff --git a/drivers/phy/eswin/Kconfig b/drivers/phy/eswin/Kconfig
new file mode 100644
index 000000000000..3fcd76582c3b
--- /dev/null
+++ b/drivers/phy/eswin/Kconfig
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Phy drivers for Eswin platforms
+#
+config PHY_EIC7700_SATA
+	tristate "eic7700 Sata SerDes/PHY driver"
+	depends on ARCH_ESWIN || COMPILE_TEST
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support SerDes/Phy found on ESWIN's
+	  EIC7700 SoC.This Phy supports SATA 1.5 Gb/s,
+	  SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds.
+	  It supports one SATA host port to accept one SATA device.
diff --git a/drivers/phy/eswin/Makefile b/drivers/phy/eswin/Makefile
new file mode 100644
index 000000000000..db08c66be812
--- /dev/null
+++ b/drivers/phy/eswin/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_PHY_EIC7700_SATA)	+= phy-eic7700-sata.o
diff --git a/drivers/phy/eswin/phy-eic7700-sata.c b/drivers/phy/eswin/phy-eic7700-sata.c
new file mode 100644
index 000000000000..19b7ddf2583f
--- /dev/null
+++ b/drivers/phy/eswin/phy-eic7700-sata.c
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ESWIN SATA PHY driver
+ *
+ * Copyright 2024, Beijing ESWIN Computing Technology Co., Ltd..
+ * All rights reserved.
+ *
+ * Authors: Yulin Lu <luyulin@eswincomputing.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+#define SATA_CLK_CTRL				0x0
+#define SATA_AXI_LP_CTRL			0x08
+#define SATA_MPLL_CTRL				0x20
+#define SATA_P0_PHY_STAT			0x24
+#define SATA_PHY_CTRL0				0x28
+#define SATA_PHY_CTRL1				0x2c
+#define SATA_REG_CTRL				0x34
+#define SATA_REF_CTRL1				0x38
+#define SATA_LOS_IDEN				0x3c
+#define SATA_RESET_CTRL				0x40
+
+#define SATA_SYS_CLK_EN				BIT(28)
+#define SATA_PHY_RESET				BIT(0)
+#define SATA_PORT_RESET				BIT(1)
+#define SATA_CLK_RST_SOURCE_PHY			BIT(0)
+#define SATA_P0_PHY_TX_AMPLITUDE_GEN1_MASK	GENMASK(6, 0)
+#define SATA_P0_PHY_TX_AMPLITUDE_GEN2_MASK	GENMASK(14, 8)
+#define SATA_P0_PHY_TX_AMPLITUDE_GEN3_MASK	GENMASK(22, 16)
+#define SATA_P0_PHY_TX_PREEMPH_GEN1_MASK	GENMASK(5, 0)
+#define SATA_P0_PHY_TX_PREEMPH_GEN2_MASK	GENMASK(13, 8)
+#define SATA_P0_PHY_TX_PREEMPH_GEN3_MASK	GENMASK(21, 16)
+#define SATA_LOS_LEVEL_MASK			GENMASK(4, 0)
+#define SATA_LOS_BIAS_MASK			GENMASK(18, 16)
+#define SATA_M_CSYSREQ				BIT(0)
+#define SATA_S_CSYSREQ				BIT(16)
+#define SATA_REF_REPEATCLK_EN			BIT(0)
+#define SATA_REF_USE_PAD			BIT(20)
+#define SATA_MPLL_MULTIPLIER_MASK		GENMASK(22, 16)
+#define SATA_P0_PHY_READY			BIT(0)
+
+#define PHY_READY_TIMEOUT			(usecs_to_jiffies(4000))
+
+struct eic7700_sata_phy {
+	void __iomem *regs;
+	struct phy *phy;
+};
+
+static int wait_for_phy_ready(void __iomem *base, u32 reg, u32 checkbit,
+			      u32 status)
+{
+	unsigned long timeout = jiffies + PHY_READY_TIMEOUT;
+
+	while (time_before(jiffies, timeout)) {
+		if ((readl(base + reg) & checkbit) == status)
+			return 0;
+		usleep_range(50, 70);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int eic7700_sata_phy_init(struct phy *phy)
+{
+	struct eic7700_sata_phy *sata_phy = phy_get_drvdata(phy);
+	u32 val;
+	int ret;
+
+	/*
+	 * The SATA_CLK_CTRL register offset controls the pmalive, rxoob, and
+	 * rbc clocks gate provided by the PHY through the HSP bus, and it is
+	 * not registered in the clock tree.
+	 */
+	val = readl(sata_phy->regs + SATA_CLK_CTRL);
+	val |= SATA_SYS_CLK_EN;
+	writel(val, sata_phy->regs + SATA_CLK_CTRL);
+
+	writel(SATA_CLK_RST_SOURCE_PHY, sata_phy->regs + SATA_REF_CTRL1);
+	writel(FIELD_PREP(SATA_P0_PHY_TX_AMPLITUDE_GEN1_MASK, 0x42) |
+	       FIELD_PREP(SATA_P0_PHY_TX_AMPLITUDE_GEN2_MASK, 0x46) |
+	       FIELD_PREP(SATA_P0_PHY_TX_AMPLITUDE_GEN3_MASK, 0x73),
+	       sata_phy->regs + SATA_PHY_CTRL0);
+	writel(FIELD_PREP(SATA_P0_PHY_TX_PREEMPH_GEN1_MASK, 0x5) |
+	       FIELD_PREP(SATA_P0_PHY_TX_PREEMPH_GEN2_MASK, 0x5) |
+	       FIELD_PREP(SATA_P0_PHY_TX_PREEMPH_GEN3_MASK, 0x8),
+	       sata_phy->regs + SATA_PHY_CTRL1);
+	writel(FIELD_PREP(SATA_LOS_LEVEL_MASK, 0x9) |
+	       FIELD_PREP(SATA_LOS_BIAS_MASK, 0x2),
+	       sata_phy->regs + SATA_LOS_IDEN);
+	writel(SATA_M_CSYSREQ | SATA_S_CSYSREQ,
+	       sata_phy->regs + SATA_AXI_LP_CTRL);
+	writel(SATA_REF_REPEATCLK_EN | SATA_REF_USE_PAD,
+	       sata_phy->regs + SATA_REG_CTRL);
+	writel(FIELD_PREP(SATA_MPLL_MULTIPLIER_MASK, 0x3c),
+	       sata_phy->regs + SATA_MPLL_CTRL);
+	usleep_range(15, 20);
+
+	/*
+	 * The SATA_RESET_CTRL register offset controls reset/deassert for both
+	 * the port and the PHY through the HSP bus, and it is not registered
+	 * in the reset tree.
+	 */
+	val = readl(sata_phy->regs + SATA_RESET_CTRL);
+	val &= ~(SATA_PHY_RESET | SATA_PORT_RESET);
+	writel(val, sata_phy->regs + SATA_RESET_CTRL);
+
+	ret = wait_for_phy_ready(sata_phy->regs, SATA_P0_PHY_STAT,
+				 SATA_P0_PHY_READY, 1);
+	if (ret < 0)
+		dev_err(&sata_phy->phy->dev,
+			"PHY READY check failed\n");
+	return ret;
+}
+
+static int eic7700_sata_phy_exit(struct phy *phy)
+{
+	struct eic7700_sata_phy *sata_phy = phy_get_drvdata(phy);
+	u32 val;
+
+	val = readl(sata_phy->regs + SATA_RESET_CTRL);
+	val |= SATA_PHY_RESET | SATA_PORT_RESET;
+	writel(val, sata_phy->regs + SATA_RESET_CTRL);
+
+	val = readl(sata_phy->regs + SATA_CLK_CTRL);
+	val &= ~SATA_SYS_CLK_EN;
+	writel(val, sata_phy->regs + SATA_CLK_CTRL);
+
+	return 0;
+}
+
+static const struct phy_ops eic7700_sata_phy_ops = {
+	.init		= eic7700_sata_phy_init,
+	.exit		= eic7700_sata_phy_exit,
+	.owner		= THIS_MODULE,
+};
+
+static int eic7700_sata_phy_probe(struct platform_device *pdev)
+{
+	struct eic7700_sata_phy *sata_phy;
+	struct phy_provider *phy_provider;
+	struct device *dev = &pdev->dev;
+
+	sata_phy = devm_kzalloc(dev, sizeof(*sata_phy), GFP_KERNEL);
+	if (!sata_phy)
+		return -ENOMEM;
+
+	sata_phy->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(sata_phy->regs))
+		return PTR_ERR(sata_phy->regs);
+
+	dev_set_drvdata(dev, sata_phy);
+
+	sata_phy->phy = devm_phy_create(dev, NULL, &eic7700_sata_phy_ops);
+	if (IS_ERR(sata_phy->phy))
+		return dev_err_probe(dev, PTR_ERR(sata_phy->phy),
+				     "failed to create PHY\n");
+
+	phy_set_drvdata(sata_phy->phy, sata_phy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider))
+		return dev_err_probe(dev, PTR_ERR(phy_provider),
+				     "failed to register PHY provider\n");
+
+	return 0;
+}
+
+static const struct of_device_id eic7700_sata_phy_of_match[] = {
+	{ .compatible = "eswin,eic7700-sata-phy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, eic7700_sata_phy_of_match);
+
+static struct platform_driver eic7700_sata_phy_driver = {
+	.probe	= eic7700_sata_phy_probe,
+	.driver = {
+		.of_match_table	= eic7700_sata_phy_of_match,
+		.name  = "eic7700-sata-phy",
+	}
+};
+module_platform_driver(eic7700_sata_phy_driver);
+
+MODULE_DESCRIPTION("SATA PHY driver for the ESWIN EIC7700 SoC");
+MODULE_AUTHOR("Yulin Lu <luyulin@eswincomputing.com>");
+MODULE_LICENSE("GPL");
-- 
2.25.1