[PATCH v10 5/8] media: i2c: ov9282: add strobe output enable v4l2 control

[Richard Leitner <richard.leitner@linux.dev>]

Add V4L2_CID_FLASH_STROBE_OE enable/disable support using the
"strobe output enable" feature of the sensor.

All values are based on the OV9281 datasheet v1.53 (january 2019) and
tested using an ov9281 VisionComponents module.

Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
---
 drivers/media/i2c/ov9282.c | 26 +++++++++++++++++++++++++-
 1 file changed, 25 insertions(+), 1 deletion(-)

diff --git a/drivers/media/i2c/ov9282.c b/drivers/media/i2c/ov9282.c
index e67cff6c30ffa..6afce803a049d 100644
--- a/drivers/media/i2c/ov9282.c
+++ b/drivers/media/i2c/ov9282.c
@@ -670,6 +670,23 @@ static int ov9282_set_ctrl_vflip(struct ov9282 *ov9282, int value)
 				current_val);
 }
 
+static int ov9282_set_ctrl_flash_strobe_oe(struct ov9282 *ov9282, bool enable)
+{
+	u32 current_val;
+	int ret;
+
+	ret = ov9282_read_reg(ov9282, OV9282_REG_OUTPUT_ENABLE6, 1, &current_val);
+	if (ret)
+		return ret;
+
+	if (enable)
+		current_val |= OV9282_OUTPUT_ENABLE6_STROBE;
+	else
+		current_val &= ~OV9282_OUTPUT_ENABLE6_STROBE;
+
+	return ov9282_write_reg(ov9282, OV9282_REG_OUTPUT_ENABLE6, 1, current_val);
+}
+
 /**
  * ov9282_set_ctrl() - Set subdevice control
  * @ctrl: pointer to v4l2_ctrl structure
@@ -736,6 +753,9 @@ static int ov9282_set_ctrl(struct v4l2_ctrl *ctrl)
 		ret = ov9282_write_reg(ov9282, OV9282_REG_TIMING_HTS, 2,
 				       (ctrl->val + ov9282->cur_mode->width) >> 1);
 		break;
+	case V4L2_CID_FLASH_STROBE_OE:
+		ret = ov9282_set_ctrl_flash_strobe_oe(ov9282, ctrl->val);
+		break;
 	default:
 		dev_err(ov9282->dev, "Invalid control %d", ctrl->id);
 		ret = -EINVAL;
@@ -1325,7 +1345,7 @@ static int ov9282_init_controls(struct ov9282 *ov9282)
 	u32 lpfr;
 	int ret;
 
-	ret = v4l2_ctrl_handler_init(ctrl_hdlr, 10);
+	ret = v4l2_ctrl_handler_init(ctrl_hdlr, 11);
 	if (ret)
 		return ret;
 
@@ -1390,6 +1410,10 @@ static int ov9282_init_controls(struct ov9282 *ov9282)
 						OV9282_TIMING_HTS_MAX - mode->width,
 						1, hblank_min);
 
+	/* Flash/Strobe controls */
+	v4l2_ctrl_new_std(ctrl_hdlr, &ov9282_ctrl_ops,
+			  V4L2_CID_FLASH_STROBE_OE, 0, 1, 1, 0);
+
 	ret = v4l2_fwnode_device_parse(ov9282->dev, &props);
 	if (!ret) {
 		/* Failure sets ctrl_hdlr->error, which we check afterwards anyway */

-- 
2.47.3