From: Sasha Levin <sashal@kernel.org>
To: patches@lists.linux.dev, stable@vger.kernel.org
Cc: Chingbin Li <liqb365@163.com>,
Luiz Augusto von Dentz <luiz.von.dentz@intel.com>,
Sasha Levin <sashal@kernel.org>,
marcel@holtmann.org, luiz.dentz@gmail.com,
linux-bluetooth@vger.kernel.org
Subject: [PATCH AUTOSEL 6.18-6.6] Bluetooth: btusb: Add new VID/PID 2b89/6275 for RTL8761BUV
Date: Mon, 8 Dec 2025 19:15:28 -0500 [thread overview]
Message-ID: <20251209001610.611575-36-sashal@kernel.org> (raw)
In-Reply-To: <20251209001610.611575-1-sashal@kernel.org>
From: Chingbin Li <liqb365@163.com>
[ Upstream commit 8dbbb5423c0802ec21266765de80fd491868fab1 ]
Add VID 2b89 & PID 6275 for Realtek RTL8761BUV USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2b89 ProdID=6275 Rev= 2.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00E04C239987
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Chingbin Li <liqb365@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
LLM Generated explanations, may be completely bogus:
## Commit Analysis: Bluetooth: btusb: Add new VID/PID 2b89/6275 for
RTL8761BUV
### 1. COMMIT MESSAGE ANALYSIS
- **Subject:** Adding a USB VID (0x2b89) / PID (0x6275) for a Realtek
RTL8761BUV Bluetooth chip
- **No "Fixes:" tag** - This is not fixing a code bug
- **No "Cc: stable@vger.kernel.org"** - Not explicitly tagged for stable
- **Evidence of real hardware:** The commit includes detailed USB device
information from `/sys/kernel/debug/usb/devices`, showing the
contributor has physical access to the device
### 2. CODE CHANGE ANALYSIS
The change is minimal - just 2 lines added to
`drivers/bluetooth/btusb.c`:
```c
{ USB_DEVICE(0x2b89, 0x6275), .driver_info = BTUSB_REALTEK |
BTUSB_WIDEBAND_SPEECH },
```
This entry:
- Is added to the `quirks_table[]` array in the "Additional Realtek
8761BUV Bluetooth devices" section
- Uses the exact same pattern and flags as other RTL8761BUV entries
- The same vendor ID (0x2b89) already exists with a different product ID
(0x8761)
### 3. CLASSIFICATION
This is a **NEW DEVICE ID** addition - one of the explicitly allowed
exceptions for stable trees:
- Adds a USB ID to an existing, mature driver (btusb)
- The btusb driver already fully supports RTL8761BUV chips
- Only the device ID is new, not any driver functionality
### 4. SCOPE AND RISK ASSESSMENT
| Factor | Assessment |
|--------|------------|
| Lines changed | 2 |
| Files touched | 1 |
| Complexity | Trivial - mechanical ID table addition |
| Risk of regression | Essentially zero |
| Pattern precedent | Exact same pattern used by dozens of other entries
|
The risk is **extremely low** because:
- The new entry cannot affect any existing devices
- It only matches the specific VID/PID combination
- All the handling code (BTUSB_REALTEK, BTUSB_WIDEBAND_SPEECH) is
already tested with similar hardware
### 5. USER IMPACT
- **Affected users:** Anyone with a Bluetooth USB adapter using VID
0x2b89 and PID 0x6275
- **Without the patch:** The device is not recognized, Bluetooth does
not work at all
- **With the patch:** Full Bluetooth functionality via the mature btusb
driver
This is a complete enablement fix for affected hardware.
### 6. STABILITY INDICATORS
- Signed-off-by from the Bluetooth subsystem maintainer (Luiz Augusto
von Dentz)
- Follows established patterns exactly
- USB device info in commit shows real-world testing on actual hardware
### 7. DEPENDENCY CHECK
- **No dependencies** on other commits
- The required flags (BTUSB_REALTEK, BTUSB_WIDEBAND_SPEECH) have existed
for years
- Will apply cleanly to all stable trees with btusb support
---
## Summary
This commit is a textbook example of a stable-appropriate device ID
addition:
**Pros:**
- Trivial 2-line change adding a USB VID/PID
- Zero risk of regression - only affects the specific new device
- Enables real hardware for users who otherwise have no Bluetooth
- Follows exact pattern used by many other stable-backported device ID
additions
- Already merged by subsystem maintainer
**Cons:**
- No explicit stable tag (but not required for device ID additions)
- No Fixes: tag (appropriate - this isn't fixing broken code)
**Risk vs Benefit:** Near-zero risk with clear benefit for hardware
owners.
Per the stable kernel rules, device ID additions to existing drivers are
explicitly appropriate for backporting. They are small, obviously
correct, fix a real user problem (hardware not working), and cannot
introduce regressions.
**YES**
drivers/bluetooth/btusb.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 9b199da1c0d67..cc03c8c38b16f 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -785,6 +785,8 @@ static const struct usb_device_id quirks_table[] = {
BTUSB_WIDEBAND_SPEECH },
{ USB_DEVICE(0x2b89, 0x8761), .driver_info = BTUSB_REALTEK |
BTUSB_WIDEBAND_SPEECH },
+ { USB_DEVICE(0x2b89, 0x6275), .driver_info = BTUSB_REALTEK |
+ BTUSB_WIDEBAND_SPEECH },
/* Additional Realtek 8821AE Bluetooth devices */
{ USB_DEVICE(0x0b05, 0x17dc), .driver_info = BTUSB_REALTEK },
--
2.51.0
next prev parent reply other threads:[~2025-12-09 0:18 UTC|newest]
Thread overview: 47+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-12-09 0:14 [PATCH AUTOSEL 6.18-6.1] ksmbd: fix use-after-free in ksmbd_tree_connect_put under concurrency Sasha Levin
2025-12-09 0:14 ` [PATCH AUTOSEL 6.18-6.17] wifi: rtw89: use skb_dequeue() for queued ROC packets to prevent racing Sasha Levin
2025-12-09 0:14 ` [PATCH AUTOSEL 6.18-6.6] ipv6: clean up routes when manually removing address with a lifetime Sasha Levin
2025-12-09 0:14 ` [PATCH AUTOSEL 6.18-5.10] ext4: remove page offset calculation in ext4_block_zero_page_range() Sasha Levin
2025-12-09 0:14 ` [PATCH AUTOSEL 6.18-6.6] fs/ntfs3: fix KMSAN uninit-value in ni_create_attr_list Sasha Levin
2025-12-09 0:14 ` [PATCH AUTOSEL 6.18-6.6] btrfs: abort transaction on item count overflow in __push_leaf_left() Sasha Levin
2025-12-09 0:14 ` [PATCH AUTOSEL 6.18-6.1] smb/server: fix return value of smb2_ioctl() Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.1] gfs2: Fix use of bio_chain Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] Bluetooth: btusb: Add new VID/PID 13d3/3533 for RTL8821CE Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] wifi: mac80211: reset CRC valid after CSA Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] Bluetooth: btusb: Add new VID/PID 0x0489/0xE12F for RTL8852BE-VT Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] wifi: mt76: mmio_*_copy fix byte order and alignment Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] btrfs: scrub: always update btrfs_scrub_progress::last_physical Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] bpf: Skip bounds adjustment for conditional jumps on same scalar register Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] wifi: rtl8xxxu: Fix HT40 channel config for RTL8192CU, RTL8723AU Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] Bluetooth: btusb: MT7920: Add VID/PID 0489/e135 Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] Bluetooth: btusb: MT7922: Add VID/PID 0489/e170 Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] virtio_blk: NULL out vqs to avoid double free on failed resume Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.1] kbuild: Use objtree for module signing key path Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.17] btrfs: use kvcalloc for btrfs_bio::csum allocation Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] net: sched: Don't use WARN_ON_ONCE() for -ENOMEM in tcf_classify() Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] hfsplus: Verify inode mode when loading from disk Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.6] gfs2: fix remote evict for read-only filesystems Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] net: amd-xgbe: use EOPNOTSUPP instead of ENOTSUPP in xgbe_phy_mii_read_c45 Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] net: init shinfo->gso_segs from qdisc_pkt_len_init() Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.17] Bluetooth: btusb: add new custom firmwares Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] hfsplus: fix missing hfs_bnode_get() in __hfs_bnode_create Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] cxgb4: Rename sched_class to avoid type clash Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] net: mana: Drop TX skb on post_work_request failure and unmap resources Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] hfsplus: fix volume corruption issue for generic/070 Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.17] wifi: rtw89: rtw8852bu: Added dev id for ASUS AX57 NANO USB Wifi dongle Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] net: restore napi_consume_skb()'s NULL-handling Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.15] fs/ntfs3: Support timestamps prior to epoch Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.1] smb/server: fix return value of smb2_query_dir() Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.17] wifi: rtw88: Add BUFFALO WI-U3-866DHP to the USB ID list Sasha Levin
2025-12-09 0:15 ` Sasha Levin [this message]
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] bpf: Disable file_alloc_security hook Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.1] wifi: rtw89: phy: fix out-of-bounds access in rtw89_phy_read_txpwr_limit() Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.6] ntfs: set dummy blocksize to read boot_block when mounting Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-5.10] hfsplus: fix volume corruption issue for generic/073 Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] wifi: mt76: mt792x: fix wifi init fail by setting MCU_RUNNING after CLC load Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.12] gfs2: Fix "gfs2: Switch to wait_event in gfs2_quotad" Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.6] ksmbd: vfs: fix race on m_flags in vfs_cache Sasha Levin
2025-12-09 0:15 ` [PATCH AUTOSEL 6.18-6.1] wifi: rtw89: flush TX queue before deleting key Sasha Levin
2025-12-09 0:15 ` [Intel-wired-lan] [PATCH AUTOSEL 6.18-6.12] ice: Allow 100M speed for E825C SGMII device Sasha Levin
2025-12-09 0:15 ` Sasha Levin
-- strict thread matches above, loose matches on Subject: below --
2025-12-06 14:02 [PATCH AUTOSEL 6.18-6.1] ksmbd: fix use-after-free in ksmbd_tree_connect_put under concurrency Sasha Levin
2025-12-06 14:02 ` [PATCH AUTOSEL 6.18-6.6] Bluetooth: btusb: Add new VID/PID 2b89/6275 for RTL8761BUV Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251209001610.611575-36-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=linux-bluetooth@vger.kernel.org \
--cc=liqb365@163.com \
--cc=luiz.dentz@gmail.com \
--cc=luiz.von.dentz@intel.com \
--cc=marcel@holtmann.org \
--cc=patches@lists.linux.dev \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.