[PATCH net-next v1 1/3] dt-bindings: net: micrel: Convert to YAML schema

[Stefan Eichenberger <eichest@gmail.com>]

From: Stefan Eichenberger <stefan.eichenberger@toradex.com>

Convert the devicetree bindings for the Micrel PHY to YAML schema. This
also combines the information from micrel.txt and micrel-ksz90x1.txt
into a single micrel.yaml file as this PHYs are from the same series.
Use yaml conditions to differentiate the properties that only apply to
specific PHY models.

Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
---
 .../bindings/net/micrel-ksz90x1.txt           | 228 --------
 .../devicetree/bindings/net/micrel.txt        |  57 --
 .../devicetree/bindings/net/micrel.yaml       | 527 ++++++++++++++++++
 3 files changed, 527 insertions(+), 285 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
 delete mode 100644 Documentation/devicetree/bindings/net/micrel.txt
 create mode 100644 Documentation/devicetree/bindings/net/micrel.yaml

diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
deleted file mode 100644
index 6f7b907d5a044..0000000000000
--- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
+++ /dev/null
@@ -1,228 +0,0 @@
-Micrel KSZ9021/KSZ9031/KSZ9131 Gigabit Ethernet PHY
-
-Some boards require special tuning values, particularly when it comes
-to clock delays. You can specify clock delay values in the PHY OF
-device node. Deprecated, but still supported, these properties can
-also be added to an Ethernet OF device node.
-
-Note that these settings are applied after any phy-specific fixup from
-phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c),
-and therefore may overwrite them.
-
-KSZ9021:
-
-  All skew control options are specified in picoseconds. The minimum
-  value is 0, the maximum value is 3000, and it can be specified in 200ps
-  steps, *but* these values are in no way what you get because this chip's
-  skew values actually increase in 120ps steps, starting from -840ps. The
-  incorrect values came from an error in the original KSZ9021 datasheet
-  before it was corrected in revision 1.2 (Feb 2014), but it is too late to
-  change the driver now because of the many existing device trees that have
-  been created using values that go up in increments of 200.
-
-  The following table shows the actual skew delay you will get for each of the
-  possible devicetree values, and the number that will be programmed into the
-  corresponding pad skew register:
-
-  Device Tree Value	Delay	Pad Skew Register Value
-  -----------------------------------------------------
-	0   		-840ps		0000
-	200 		-720ps		0001
-	400 		-600ps		0010
-	600 		-480ps		0011
-	800 		-360ps		0100
-	1000		-240ps		0101
-	1200		-120ps		0110
-	1400		   0ps		0111
-	1600		 120ps		1000
-	1800		 240ps		1001
-	2000		 360ps		1010
-	2200		 480ps		1011
-	2400		 600ps		1100
-	2600		 720ps		1101
-	2800		 840ps		1110
-	3000		 960ps		1111
-
-  Optional properties:
-
-    - rxc-skew-ps : Skew control of RXC pad
-    - rxdv-skew-ps : Skew control of RX CTL pad
-    - txc-skew-ps : Skew control of TXC pad
-    - txen-skew-ps : Skew control of TX CTL pad
-    - rxd0-skew-ps : Skew control of RX data 0 pad
-    - rxd1-skew-ps : Skew control of RX data 1 pad
-    - rxd2-skew-ps : Skew control of RX data 2 pad
-    - rxd3-skew-ps : Skew control of RX data 3 pad
-    - txd0-skew-ps : Skew control of TX data 0 pad
-    - txd1-skew-ps : Skew control of TX data 1 pad
-    - txd2-skew-ps : Skew control of TX data 2 pad
-    - txd3-skew-ps : Skew control of TX data 3 pad
-
-KSZ9031:
-
-  All skew control options are specified in picoseconds. The minimum
-  value is 0, and the maximum is property-dependent. The increment
-  step is 60ps. The default value is the neutral setting, so setting
-  rxc-skew-ps=<0> actually results in -900 picoseconds adjustment.
-
-  The KSZ9031 hardware supports a range of skew values from negative to
-  positive, where the specific range is property dependent. All values
-  specified in the devicetree are offset by the minimum value so they
-  can be represented as positive integers in the devicetree since it's
-  difficult to represent a negative number in the devictree.
-
-  The following 5-bit values table apply to rxc-skew-ps and txc-skew-ps.
-
-  Pad Skew Value	Delay (ps)	Devicetree Value
-  ------------------------------------------------------
-  0_0000		-900ps		0
-  0_0001		-840ps		60
-  0_0010		-780ps		120
-  0_0011		-720ps		180
-  0_0100		-660ps		240
-  0_0101		-600ps		300
-  0_0110		-540ps		360
-  0_0111		-480ps		420
-  0_1000		-420ps		480
-  0_1001		-360ps		540
-  0_1010		-300ps		600
-  0_1011		-240ps		660
-  0_1100		-180ps		720
-  0_1101		-120ps		780
-  0_1110		-60ps		840
-  0_1111		0ps		900
-  1_0000		60ps		960
-  1_0001		120ps		1020
-  1_0010		180ps		1080
-  1_0011		240ps		1140
-  1_0100		300ps		1200
-  1_0101		360ps		1260
-  1_0110		420ps		1320
-  1_0111		480ps		1380
-  1_1000		540ps		1440
-  1_1001		600ps		1500
-  1_1010		660ps		1560
-  1_1011		720ps		1620
-  1_1100		780ps		1680
-  1_1101		840ps		1740
-  1_1110		900ps		1800
-  1_1111		960ps		1860
-
-  The following 4-bit values table apply to the txdX-skew-ps, rxdX-skew-ps
-  data pads, and the rxdv-skew-ps, txen-skew-ps control pads.
-
-  Pad Skew Value	Delay (ps)	Devicetree Value
-  ------------------------------------------------------
-  0000			-420ps		0
-  0001			-360ps		60
-  0010			-300ps		120
-  0011			-240ps		180
-  0100			-180ps		240
-  0101			-120ps		300
-  0110			-60ps		360
-  0111			0ps		420
-  1000			60ps		480
-  1001			120ps		540
-  1010			180ps		600
-  1011			240ps		660
-  1100			300ps		720
-  1101			360ps		780
-  1110			420ps		840
-  1111			480ps		900
-
-  Optional properties:
-
-    Maximum value of 1860, default value 900:
-
-      - rxc-skew-ps : Skew control of RX clock pad
-      - txc-skew-ps : Skew control of TX clock pad
-
-    Maximum value of 900, default value 420:
-
-      - rxdv-skew-ps : Skew control of RX CTL pad
-      - txen-skew-ps : Skew control of TX CTL pad
-      - rxd0-skew-ps : Skew control of RX data 0 pad
-      - rxd1-skew-ps : Skew control of RX data 1 pad
-      - rxd2-skew-ps : Skew control of RX data 2 pad
-      - rxd3-skew-ps : Skew control of RX data 3 pad
-      - txd0-skew-ps : Skew control of TX data 0 pad
-      - txd1-skew-ps : Skew control of TX data 1 pad
-      - txd2-skew-ps : Skew control of TX data 2 pad
-      - txd3-skew-ps : Skew control of TX data 3 pad
-
-    - micrel,force-master:
-        Boolean, force phy to master mode. Only set this option if the phy
-        reference clock provided at CLK125_NDO pin is used as MAC reference
-        clock because the clock jitter in slave mode is too high (errata#2).
-        Attention: The link partner must be configurable as slave otherwise
-        no link will be established.
-
-KSZ9131:
-LAN8841:
-
-  All skew control options are specified in picoseconds. The increment
-  step is 100ps. Unlike KSZ9031, the values represent picoseccond delays.
-  A negative value can be assigned as rxc-skew-psec = <(-100)>;.
-
-  Optional properties:
-
-    Range of the value -700 to 2400, default value 0:
-
-      - rxc-skew-psec : Skew control of RX clock pad
-      - txc-skew-psec : Skew control of TX clock pad
-
-    Range of the value -700 to 800, default value 0:
-
-      - rxdv-skew-psec : Skew control of RX CTL pad
-      - txen-skew-psec : Skew control of TX CTL pad
-      - rxd0-skew-psec : Skew control of RX data 0 pad
-      - rxd1-skew-psec : Skew control of RX data 1 pad
-      - rxd2-skew-psec : Skew control of RX data 2 pad
-      - rxd3-skew-psec : Skew control of RX data 3 pad
-      - txd0-skew-psec : Skew control of TX data 0 pad
-      - txd1-skew-psec : Skew control of TX data 1 pad
-      - txd2-skew-psec : Skew control of TX data 2 pad
-      - txd3-skew-psec : Skew control of TX data 3 pad
-
-Examples:
-
-	/* Attach to an Ethernet device with autodetected PHY */
-	&enet {
-		rxc-skew-ps = <1800>;
-		rxdv-skew-ps = <0>;
-		txc-skew-ps = <1800>;
-		txen-skew-ps = <0>;
-		status = "okay";
-	};
-
-	/* Attach to an explicitly-specified PHY */
-	mdio {
-		phy0: ethernet-phy@0 {
-			rxc-skew-ps = <1800>;
-			rxdv-skew-ps = <0>;
-			txc-skew-ps = <1800>;
-			txen-skew-ps = <0>;
-			reg = <0>;
-		};
-	};
-	ethernet@70000 {
-		phy = <&phy0>;
-		phy-mode = "rgmii-id";
-	};
-
-References
-
-  Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014.
-  http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf
-
-  Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014.
-  http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf
-
-Notes:
-
-  Note that a previous version of the Micrel ksz9021rl/rn Data Sheet
-  was missing extended register 106 (transmit data pad skews), and
-  incorrectly specified the ps per step as 200ps/step instead of
-  120ps/step. The latest update to this document reflects the latest
-  revision of the Micrel specification even though usage in the kernel
-  still reflects that incorrect document.
diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt
deleted file mode 100644
index 01622ce58112e..0000000000000
--- a/Documentation/devicetree/bindings/net/micrel.txt
+++ /dev/null
@@ -1,57 +0,0 @@
-Micrel PHY properties.
-
-These properties cover the base properties Micrel PHYs.
-
-Optional properties:
-
- - micrel,led-mode : LED mode value to set for PHYs with configurable LEDs.
-
-	Configure the LED mode with single value. The list of PHYs and the
-	bits that are currently supported:
-
-	KSZ8001: register 0x1e, bits 15..14
-	KSZ8041: register 0x1e, bits 15..14
-	KSZ8021: register 0x1f, bits 5..4
-	KSZ8031: register 0x1f, bits 5..4
-	KSZ8051: register 0x1f, bits 5..4
-	KSZ8081: register 0x1f, bits 5..4
-	KSZ8091: register 0x1f, bits 5..4
-	LAN8814: register EP5.0, bit 6
-
-	See the respective PHY datasheet for the mode values.
-
- - micrel,rmii-reference-clock-select-25-mhz: RMII Reference Clock Select
-						bit selects 25 MHz mode
-
-	Setting the RMII Reference Clock Select bit enables 25 MHz rather
-	than 50 MHz clock mode.
-
-	Note that this option is only needed for certain PHY revisions with a
-	non-standard, inverted function of this configuration bit.
-	Specifically, a clock reference ("rmii-ref" below) is always needed to
-	actually select a mode.
-
- - clocks, clock-names: contains clocks according to the common clock bindings.
-
-	supported clocks:
-	- KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference
-	  input clock. Used to determine the XI input clock.
-
- - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
-
-	Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled
-	by the FXEN boot strapping pin. It can't be determined from the PHY
-	registers whether the PHY is in fiber mode, so this boolean device tree
-	property can be used to describe it.
-
-	In fiber mode, auto-negotiation is disabled and the PHY can only work in
-	100base-fx (full and half duplex) modes.
-
- - coma-mode-gpios: If present the given gpio will be deasserted when the
-		    PHY is probed.
-
-	Some PHYs have a COMA mode input pin which puts the PHY into
-	isolate and power-down mode. On some boards this input is connected
-	to a GPIO of the SoC.
-
-	Supported on the LAN8814.
diff --git a/Documentation/devicetree/bindings/net/micrel.yaml b/Documentation/devicetree/bindings/net/micrel.yaml
new file mode 100644
index 0000000000000..f48e9b9120ca0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/micrel.yaml
@@ -0,0 +1,527 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/micrel.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Micrel KSZ series PHYs and switches
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+  - Stefan Eichenberger <eichest@gmail.com>
+
+description: |
+  The Micrel KSZ series contains different network phys and switches.
+
+  Some boards require special tuning values, particularly when it comes to
+  clock delays. You can specify clock delay values in the PHY OF device node.
+
+properties:
+  compatible:
+    enum:
+      - ethernet-phy-id000e.7237 # KSZ8873MLL
+      - ethernet-phy-id0022.1430 # KSZ886X
+      - ethernet-phy-id0022.1435 # KSZ8863
+      - ethernet-phy-id0022.1510 # KSZ8041
+      - ethernet-phy-id0022.1537 # KSZ8041RNLI
+      - ethernet-phy-id0022.1550 # KSZ8051
+      - ethernet-phy-id0022.1555 # KSZ8021
+      - ethernet-phy-id0022.1556 # KSZ8031
+      - ethernet-phy-id0022.1560 # KSZ8081, KSZ8091
+      - ethernet-phy-id0022.1570 # KSZ8061
+      - ethernet-phy-id0022.1610 # KSZ9021
+      - ethernet-phy-id0022.1611 # KSZ9021RLRN
+      - ethernet-phy-id0022.161a # KSZ8001
+      - ethernet-phy-id0022.1620 # KSZ9031
+      - ethernet-phy-id0022.1631 # KSZ9477
+      - ethernet-phy-id0022.1640 # KSZ9131
+      - ethernet-phy-id0022.1650 # LAN8841
+      - ethernet-phy-id0022.1660 # LAN8814
+      - ethernet-phy-id0022.1670 # LAN8804
+      - ethernet-phy-id0022.1720 # KS8737
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ethernet-phy-id0022.1510
+    then:
+      properties:
+        micrel,fiber-mode:
+          type: boolean
+          description: |
+            If present the PHY is configured to operate in fiber mode.
+
+            The KSZ8041FTL variant, supports fiber mode, enabled by the FXEN
+            boot strapping pin. It can't be determined from the PHY registers
+            whether the PHY is in fiber mode, so this boolean device tree
+            property can be used to describe it.
+
+            In fiber mode, auto-negotiation is disabled and the PHY can only work in
+            100base-fx (full and half duplex) modes.
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - ethernet-phy-id0022.1555
+              - ethernet-phy-id0022.1556
+              - ethernet-phy-id0022.1560
+    then:
+      properties:
+        clock-names:
+          const: rmii-ref
+          description: |
+            supported clocks:
+              - The RMII reference input clock. Used to determine the XI
+                input clock.
+        micrel,rmii-reference-clock-select-25-mhz:
+          type: boolean
+          description: |
+            RMII Reference Clock Select bit selects 25 MHz mode
+
+            Setting the RMII Reference Clock Select bit enables 25 MHz rather
+            than 50 MHz clock mode.
+
+            Note that this option in only needed for certain PHY revisions with a
+            non-standard, inverted function of this configuration bit.
+            Specifically, a clock reference ("rmii-ref") is always needed to
+            actually select a mode.
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ethernet-phy-id0022.1660
+    then:
+      properties:
+        coma-mode-gpios:
+          maxItems: 1
+          description: |
+            If present the given gpio will be deasserted when the PHY is probed.
+
+            Some PHYs have a COMA mode input pin which puts the PHY into
+            isolate and power-down mode. On some boards this input is connected
+            to a GPIO of the SoC.
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - ethernet-phy-id0022.1510
+              - ethernet-phy-id0022.1555
+              - ethernet-phy-id0022.1556
+              - ethernet-phy-id0022.1550
+              - ethernet-phy-id0022.1560
+              - ethernet-phy-id0022.161a
+              - ethernet-phy-id0022.1660
+    then:
+      properties:
+        micrel,led-mode:
+          description: |
+            LED mode value to set for PHYs with configurable LEDs.
+
+            Configure the LED mode with single value. The list of PHYs and the
+            bits that are currently supported:
+
+            KSZ8001: register 0x1e, bits 15..14
+            KSZ8041: register 0x1e, bits 15..14
+            KSZ8021: register 0x1f, bits 5..4
+            KSZ8031: register 0x1f, bits 5..4
+            KSZ8051: register 0x1f, bits 5..4
+            KSZ8081: register 0x1f, bits 5..4
+            KSZ8091: register 0x1f, bits 5..4
+            LAN8814: register EP5.0, bit 6
+
+            See the respective PHY datasheet for the mode values.
+          minimum: 0
+          maximum: 3
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ethernet-phy-id0022.1620
+    then:
+      properties:
+        enable-edpd:
+          type: boolean
+          description:
+            Enable Energy Detect Power Down mode. Reduces power consumption when the
+            link is down.
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - ethernet-phy-id0022.1555
+              - ethernet-phy-id0022.1556
+              - ethernet-phy-id0022.1560
+    then:
+      properties:
+        clock-names:
+          const: rmii-ref
+          description: |
+            supported clocks:
+              - The RMII reference input clock. Used to determine the XI
+                input clock.
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - ethernet-phy-id0022.1610
+              - ethernet-phy-id0022.1611
+    then:
+      properties:
+        rxc-skew-ps:
+          description: |
+            Skew control of RXC pad (picoseconds). A value of 0 equals to a
+            skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        txc-skew-ps:
+          description: |
+            Skew control of TXC pad (picoseconds). A value of 0 equals to a
+            skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        rxdv-skew-ps:
+          description: |
+            Skew control of RX CTL pad (picoseconds). A value of 0 equals to a
+            skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        txen-skew-ps:
+          description: |
+            Skew control of TX CTL pad (picoseconds). A value of 0 equals to a
+            skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        rxd0-skew-ps:
+          description: |
+            Skew control of RX data 0 pad (picoseconds). A value of 0 equals to
+            a skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        rxd1-skew-ps:
+          description: |
+            Skew control of RX data 1 pad (picoseconds). A value of 0 equals to
+            a skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        rxd2-skew-ps:
+          description: |
+            Skew control of RX data 2 pad (picoseconds). A value of 0 equals to
+            a skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        rxd3-skew-ps:
+          description: |
+            Skew control of RX data 3 pad (picoseconds). A value of 0 equals to
+            a skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        txd0-skew-ps:
+          description: |
+            Skew control of TX data 0 pad (picoseconds). A value of 0 equals to
+            a skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        txd1-skew-ps:
+          description: |
+            Skew control of TX data 1 pad (picoseconds). A value of 0 equals to
+            a skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        txd2-skew-ps:
+          description: |
+            Skew control of TX data 2 pad (picoseconds). A value of 0 equals to
+            a skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+        txd3-skew-ps:
+          description: |
+            Skew control of TX data 3 pad (picoseconds). A value of 0 equals to
+            a skew of -840ps. Increments of 200ps are allowed.
+
+            The actual increment on the chip is 120ps ranging from -840ps to
+            960ps, this mismatch comes from a documentation error before
+            datasheet revision 1.2 (Feb 2014):
+          minimum: 0
+          maximum: 3000
+          default: 1400
+    else:
+      if:
+        properties:
+          compatible:
+            contains:
+              const: ethernet-phy-id0022.1620
+      then:
+        properties:
+          rxc-skew-ps:
+            description: |
+              Skew control of RXC pad (picoseconds). A value of 0 equals to a skew
+              of -900ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 1860
+            default: 900
+          txc-skew-ps:
+            description: |
+              Skew control of TXC pad (picoseconds). A value of 0 equals to a skew
+              of -900ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 1860
+            default: 900
+          rxdv-skew-ps:
+            description: |
+              Skew control of RX CTL pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          txen-skew-ps:
+            description: |
+              Skew control of TX CTL pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          rxd0-skew-ps:
+            description: |
+              Skew control of RX data 0 pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          rxd1-skew-ps:
+            description: |
+              Skew control of RX data 1 pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          rxd2-skew-ps:
+            description: |
+              Skew control of RX data 2 pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          rxd3-skew-ps:
+            description: |
+              Skew control of RX data 3 pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          txd0-skew-ps:
+            description: |
+              Skew control of TX data 0 pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          txd1-skew-ps:
+            description: |
+              Skew control of TX data 1 pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          txd2-skew-ps:
+            description: |
+              Skew control of TX data 2 pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+          txd3-skew-ps:
+            description: |
+              Skew control of TX data 3 pad (picoseconds). A value of 0 equals to a
+              skew of -420ps. Increments of 60ps are allowed.
+            minimum: 0
+            maximum: 900
+            default: 420
+      else:
+        if:
+          properties:
+            compatible:
+              contains:
+                enum:
+                  - ethernet-phy-id0022.1640
+                  - ethernet-phy-id0022.1660
+        then:
+          properties:
+            rxc-skew-psec:
+              description: |
+                Skew control of RXC pad (picoseconds). A value of 0 equals to a
+                skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 2400
+              default: 0
+            txc-skew-psec:
+              description: |
+                Skew control of TXC pad (picoseconds). A value of 0 equals to a
+                skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 2400
+              default: 0
+            rxdv-skew-psec:
+              description: |
+                Skew control of RX CTL pad (picoseconds). A value of 0 equals to a
+                skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            txen-skew-psec:
+              description: |
+                Skew control of TX CTL pad (picoseconds). A value of 0 equals to a
+                skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            rxd0-skew-psec:
+              description: |
+                Skew control of RX data 0 pad (picoseconds). A value of 0 equals to
+                a skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            rxd1-skew-psec:
+              description: |
+                Skew control of RX data 1 pad (picoseconds). A value of 0 equals to
+                a skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            rxd2-skew-psec:
+              description: |
+                Skew control of RX data 2 pad (picoseconds). A value of 0 equals to
+                a skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            rxd3-skew-psec:
+              description: |
+                Skew control of RX data 3 pad (picoseconds). A value of 0 equals to
+                a skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            txd0-skew-psec:
+              description: |
+                Skew control of TX data 0 pad (picoseconds). A value of 0 equals to
+                a skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            txd1-skew-psec:
+              description: |
+                Skew control of TX data 1 pad (picoseconds). A value of 0 equals to
+                a skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            txd2-skew-psec:
+              description: |
+                Skew control of TX data 2 pad (picoseconds). A value of 0 equals to
+                a skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+            txd3-skew-psec:
+              description: |
+                Skew control of TX data 3 pad (picoseconds). A value of 0 equals to
+                a skew value of 0ps. Increments of 100ps are allowed.
+              minimum: -700
+              maximum: 800
+              default: 0
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+
+        ethernet-phy@5 {
+            compatible = "ethernet-phy-id0022.1510";
+            reg = <5>;
+            micrel,led-mode = <2>;
+            micrel,fiber-mode;
+        };
+
+        ethernet-phy@7 {
+            compatible = "ethernet-phy-id0022.1610";
+            reg = <7>;
+            rxc-skew-ps = <3000>;
+            rxdv-skew-ps = <0>;
+            txc-skew-ps = <3000>;
+            txen-skew-ps = <0>;
+        };
+
+        ethernet-phy@9 {
+            compatible = "ethernet-phy-id0022.1640";
+            reg = <9>;
+            rxc-skew-psec = <(-100)>;
+            txc-skew-psec = <(-100)>;
+        };
+    };
-- 
2.51.0