Re: [PATCH net-next v1 1/3] dt-bindings: net: micrel: Convert to YAML schema

[Simon Horman <horms@kernel.org>]

On Fri, Dec 12, 2025 at 09:46:16AM +0100, Stefan Eichenberger wrote:
> From: Stefan Eichenberger <stefan.eichenberger@toradex.com>
> 
> Convert the devicetree bindings for the Micrel PHY to YAML schema. This
> also combines the information from micrel.txt and micrel-ksz90x1.txt
> into a single micrel.yaml file as this PHYs are from the same series.
> Use yaml conditions to differentiate the properties that only apply to
> specific PHY models.
> 
> Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
> ---
>  .../bindings/net/micrel-ksz90x1.txt           | 228 --------
>  .../devicetree/bindings/net/micrel.txt        |  57 --
>  .../devicetree/bindings/net/micrel.yaml       | 527 ++++++++++++++++++
>  3 files changed, 527 insertions(+), 285 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
>  delete mode 100644 Documentation/devicetree/bindings/net/micrel.txt
>  create mode 100644 Documentation/devicetree/bindings/net/micrel.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt

...

> -  Optional properties:
> -
> -    Maximum value of 1860, default value 900:
> -
> -      - rxc-skew-ps : Skew control of RX clock pad
> -      - txc-skew-ps : Skew control of TX clock pad
> -
> -    Maximum value of 900, default value 420:
> -
> -      - rxdv-skew-ps : Skew control of RX CTL pad
> -      - txen-skew-ps : Skew control of TX CTL pad
> -      - rxd0-skew-ps : Skew control of RX data 0 pad
> -      - rxd1-skew-ps : Skew control of RX data 1 pad
> -      - rxd2-skew-ps : Skew control of RX data 2 pad
> -      - rxd3-skew-ps : Skew control of RX data 3 pad
> -      - txd0-skew-ps : Skew control of TX data 0 pad
> -      - txd1-skew-ps : Skew control of TX data 1 pad
> -      - txd2-skew-ps : Skew control of TX data 2 pad
> -      - txd3-skew-ps : Skew control of TX data 3 pad
> -
> -    - micrel,force-master:
> -        Boolean, force phy to master mode. Only set this option if the phy
> -        reference clock provided at CLK125_NDO pin is used as MAC reference
> -        clock because the clock jitter in slave mode is too high (errata#2).
> -        Attention: The link partner must be configurable as slave otherwise
> -        no link will be established.

Hi Stefan,

Sorry if this is off the mark, but Claude Code with
https://github.com/masoncl/review-prompts/ flags
that micrel,force-master is not included in the new .yaml
schema and yet it is used in the driver (and I would add,
several dts/dtsi files).

https://netdev-ai.bots.linux.dev/ai-review.html?id=2390d104-ff56-43f2-ba06-9650e8e5343b

...